Chicago Electric 95519 User's Manual
Contents
1. TOOL APPLIANCE WATTAGE Camcorder Charger 99 Watts Drill Charger 8 Watts SKU 95519 For technical questions please call 1 800 444 3353 PAGE 7 INSPECTION MAINTENANCE AND CLEANING WARNING Always make sure the Power Switch of the Inverter is in the OFF position and the unit is disconnected from its power source before performing inspection maintenance or cleaning procedures Before each use inspect the general condition of the Inverter Check for mis alignment or binding of moving parts cracked or broken parts damaged electrical wiring and any other condition that may affect its safe operation If abnormal heat noise or vibration occurs have the problem corrected before further use Do not use damaged equipment To replace the Fuse Turn the Fuse Cap on the Plug end of the Cigarette Lighter Power Cord counterclockwise and remove to expose the Fuse Pull out the old Fuse and replace with a new F10A 250V Fuse Then replace the Fuse Cap To clean the exterior parts of the Inverter use only a clean dry cloth Do not clean the unit with water or harsh cleaners NOTE This Inverter does not contain any replaceable parts It the unit needs service make sure to take it to a qualified service technician Make sure to store the Inverter in a clean dry safe location out of reach of children and other unauthorized people CAUTION All maintenance service or repairs not mentioned in this manual must only be2. and the power source must provide enough current to operate a load of 100 Watts or under Place the Inverter on a dry flat level surface capable of supporting the weight of the unit Make sure the Inverter has adequate ventilation and is not in direct sunlight Connect the 12 volt DC Cigarette Lighter Connector to the Inverter Connect the 12 volt DC Cigarette Lighter Plug to the vehicle s Cigarette Lighter Receptacle Press the Power Switch on the Inverter to turn the unit on The LED in the Power Switch will illuminate a dim BLUE indicating the Inverter is receiving 12 volt DC power NOTE If the Inverter does not turn on check to make sure the vehicle s ignition switch is actually powering the Cigarette Lighter Receptacle Some vehicles require the ignition switch to be turned on Plug the 115 volt AC device you wish to power into the 115 volt AC Outlet on the Inverter or the USB powered tool appliance into the Inverters USB Power Port The tool appliance must not use more than 100 total watts during continuous operation otherwise it may overload the Inverter NOTE The Inverter s USB Power Port does not support data communica tions It only provides 5 volt 500 mA DC maximum power to an external USB powered device USB power output is not controlled by the Power Switch of the Inverter USB power is always on when the Cigarette Lighter Power Cord is connected to a 12 volt DC power source Operate the tool appliance normal
3. any tool or appliance Keep the Inverter well ventilated Do not place any objects on top of or next to the Inverter or wrap anything around the Inverter Doing so can cause the Inverter to overheat causing a potential fire hazard and or damage to the Inverter Make sure to read and understand all warnings and safety precautions as outlined in the manufacturer s manual for the device that this Inverter is used to power Performance of this unit may vary depending on the Inverter voltage battery power or tool appliance wattage The Inverter housing will become hot when in use Avoid touching materials clothes sleeping bags carpet etc to the Inverter that can not withstand such high temperatures Avoid touching a hot Inverter with your fingers and hands SKU 95519 For technical questions please call 1 800 444 3353 PAGE 4 10 ae 12 13 14 15 16 17 18 CAUTION This Inverter must only be connected to a circuit with a nominal output voltage of 12 VDC Lower voltage will not operate the Inverter properly and more voltage could damage the unit Do not use this Inverter with positive ground electrical systems CAUTION Some rechargeable tools and appliances may damage the Inverter or the tool appliance When first using a rechargeable device check its tempera ture for the first ten minutes If it becomes abnormally hot do not use the device with the Inverter It is recommended that the vehicle be st
4. ELECTRIC BALLA 100 WATT MINI SLIM POWER INVERTER MEL 95519 ASSEMBLY AND OPERATION INSTRUCTIONS Due to continuing improvements actual product may differ slightly from the product described herein Distributed Exclusively by 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our website at http www harborfreight com TO PREVENT SERIOUS INJURY READ AND UNDERSTAND ALL WARNINGS AND INSTRUCTIONS BEFORE USE Copyright 2006 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions or replacement parts please call 1 800 444 3353 REV 1 07 SPECIFICATIONS Power Connector Type 16 AWG x 2C x 24 Long Wire Lighter Plug with F10A 250V Fuse Power Switch Type Clear Push Button with 3 Way LED Green LED Indicates 12 Volt DC Power to Unit Green LED Indicates AC Power Output is Active Red LED Indicates Overheating Electrical Problem SAVE THIS MANUAL You will need this manual for the safety warnings and precautions assembly oper ating inspection maintenance and cleaning procedures parts list and assembly diagram Keep your invoice with this manual Write the invoice number on the inside of the front cover Keep this manual and invoice in a safe and dry place for future reference GENERAL SAFETY RULES WARNING READ AND UNDERSTAND ALL INSTRUC
5. TIONS Failure to follow all instructions listed below may result in electric shock fire and or serious injury SAVE THESE INSTRUCTIONS WORK AREA 1 Keep your work area clean and well lit Cluttered benches and dark areas invite accidents 2 Do not operate power equipment in explosive atmospheres such as in the presence of flammable liquids gases or dust Power equipment creates sparks which may ignite the dust or fumes ELECTRICAL SAFETY 1 Never remove the grounding prong of a power tool or appliance or modify the plug in any way Do not use any adapter plugs with this product If the tool or SKU 95519 For technical questions please call 1 800 444 3353 PAGE 2 appliance should electrically malfunction or break down grounding provides a low resistance path to carry electricity away from the user Double insulated tools and appliances are equipped with a polarized plug one blade is wider than the other This plug will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug Do not change the plug in any way Double insulation El eliminates the need for the three wire grounded power cord and grounded power supply system Avoid body contact with grounded surfaces such as pipes radiators ranges and refrigerators There is an increased risk of electric shock if your body is grounded Do not expose power tools and appliances to rain or wet conditions Water entering a power to
6. arted every hour to recharge its battery system Doing so will help prevent any unexpected shutdown of the equipment This will also ensure there will be enough battery power to start the vehicle Do not attempt to power a device over 100 watts Doing so will damage the Inverter Do not attempt to connect or set up the unit or its components while operating your vehicle Inattention to the road may result in a serious accident This Inverter is not designed for use with medical devices WARNING People with pacemakers should consult their physician s before using this product Electromagnetic fields in close proximity to a heart pacemaker could cause interference to or failure of the pacemaker WARNING The warnings and cautions discussed in this manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator SAVE THESE INSTRUCTIONS UNPACKING When unpacking check to make sure all the parts shown in the illustrations on page 8 are included If any parts are missing or broken please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible SKU 95519 For technical questions please call 1 800 444 3353 PAGE 5 10 OPERATION INSTRUCTIONS NOTE For this Inverter to work properly your power source must provide nominal 12 volts DC
7. facilities or to lack of NX CF maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent VIS CA special or consequential damages arising from the use of our product Some states do not allow the exclusion or PA PLA limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS ZZ RY WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING NSS AN THE WARRANTIES OF MERCHANTABILITY AND FITNESS Ny D NS CA 9 YM f To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection IV Ns SS verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase i Zi KAN DX IN ZA N price if we cannot readily and quickly provide you with a replacement We will return repaired products at our y KY expense but if we determine there is no defect or that the defect resulted from causes not within the scope of AX FAA our warranty then you must bear the cost of returning the product SY GA WX PLA This warranty gives you specific legal rights and you may also have other rights which vary from state to state ZA KA a NS AG 3491 Mission Oaks Blvd PO Box 6009 Camari
8. llo CA 93011 800 444 3353 KA SSW aE NNE O es NNE O NNE es eee es ee es NNN eS CANT INGC TAN YC TIAN ICRC AIRS YC INEI INEENS RSAC SISAL SILAS SILAS SARS SKU 95519 For technical questions please call 1 800 444 3353 PAGE 9
9. ly NOTE The Inverter will not operate tools appliances that generate heat such as hair dryers electric blankets microwave ovens toasters etc Protective Features Low battery voltage Though not harmful to the Inverter this condition could dam age the power source In this case the Inverter will automatically shut down when DC input voltage falls below 10 2 volts DC Input voltage too high This situation can damage the Inverter To avoid dam age the Inverter will automatically shut down when DC input voltage exceeds 15 0 volts SKU 95519 For technical questions please call 1 800 444 3353 PAGE 6 3 Thermal shutdown protection The Inverter will automatically shut down when the unit exceeds 149 Fahrenheit 4 Overload amp short circuit protection The Inverter will automatically shut down when a short circuit occurs 5 AC ground leakage The Inverter will automatically shut down when current leak age exceeds safety level 6 NOTE The LED Light on the Inverter will illuminate RED to indicate an input voltage problem or alternately blink RED and BLUE to indicate one of the other problems listed above before automatic shut down occurs If the Inverter shuts down turn its Power Switch to OFF Remove the load Wait several minutes Then turn the unit back on TOOL APPLIANCE POWER CONSUMPTION The Table below gives approximate general use wattage Always verify the tool appliance wattage before using the Inverter
10. ng parts breakage of parts and any other condition that may affect this product s operation If damaged SKU 95519 For technical questions please call 1 800 444 3353 PAGE 3 have the Inverter serviced before using Many accidents are caused by poorly maintained power equipment Use only accessories that are recommended by the manufacturer for your model Accessories that may be suitable for one Inverter may become hazardous when used on another Inverter SERVICE Product service must be performed only by qualified repair personnel Service or maintenance performed by unqualified personnel could result in a risk of injury This Inverter does not contain any replaceable parts It the unit needs service make sure to take it to a qualified service technician Maintain labels and nameplates on the Inverter These carry important informa tion If unreadable or missing contact Harbor Freight Tools for a replacement SPECIFIC SAFETY RULES WARNING Do not plug in a battery charger if the charger has a warning that dangerous voltages are present at the battery terminals Keep the Inverter away from any direct heat source or combustible material Avoid potential electrical shock Do not attempt to open the metal housing of the Inverter Always disconnect power from the Inverter when not in use Avoid unintentional starting Make sure the Power Switch of the Inverter is in the OFF position when not in use and before plugging in
11. ol or appliance will increase the risk of electric shock Stay alert Watch what you are doing and use common sense when operat ing this product Do not use this product while tired or under the influence of drugs alcohol or medication A moment of inattention while operating this product may result in serious personal injury PERSONAL SAFETY Use safety equipment Always wear ANSI approved safety impact goggles when using this product TOOL USE AND CARE Do not force this product Use the correct product for your application The correct product will do the job better and safer at the rate for which it is designed Do not use the Inverter if the Power Switch does not turn it on or off Any product that cannot be controlled with the Power Switch is dangerous and must be replaced Turn off the Inverter and unplug it from its Power Cord before making any ad justments changing accessories or storing a tool or appliance Such preven tive safety measures reduce the risk of starting the tool or appliance accidentally Store the Inverter out of reach of children and other untrained persons This product may be dangerous in the hands of untrained users Maintain this product with care Keep the Inverter clean and dry Properly main tained power equipment are less likely to bind and are easier to control Do not use this product if damaged Tag a damaged Inverter Do not use until repaired Check for misalignment or binding of movi
12. performed by a qualified service technician TROUBLESHOOTING If you are unsure if the Inverter will have the proper amount of current to run a tool appliance use this rough guideline Take the power consumption of the load in amps and multiply it by 12 input voltage The result will be the approximate number of watts needed to power the tool appliance Example Load is rated at 26 amps 26 amps x 12 volts 312 watts needed You cannot use this device with the Inverter If your television will not turn on it is important to keep in mind some appli ances including many televisions may require two to six times their wattage to turn on This Inverter will not work with such devices If your audio system buzzes while using this Inverter it is because some sound systems cannot filter out the modified sine wave produced by the Inverter A possible solution is to use a sound system that incorporates a higher quality power supply This Inverter is designed to minimize the interference with television signals However especially with weak television signals some interference may still be vis SKU 95519 For technical questions please call 1 800 444 3353 PAGE 8 ible To correct this place the Inverter as far away as possible from the television antenna and its cables Next adjust the orientation of the Inverter to the antenna cables and television power cord to minimize the interference Also use a shielded antenna cable 5 If the lo
13. w battery alarm is on all the time try these corrective measures Re charge the battery Next check the condition of the cigarette lighter cable plug and the socket You may need to clean the socket 6 If you are getting a low output voltage try reducing the load to minimize watts You may have overloaded the Inverter Reduce your load to under 100 watts Also keep input voltage above 10 1 volts DC to maintain a constant flow of power f If you are not getting any power output turn the Power Switch off and on again Some automotive systems require that the ignition be turned on Turn the ignition to the accessory position Your devices may draw too much power to operate them The Inverter may be in thermal shutdown Let the unit cool down and make sure there is adequate ventilation around the unit WARRANTY YTN Vary Vary Vary Y CHICAGO PX Ww WY SS ESSA Ss VIX gt e ELECTRIC D NI NSI AX LIMITED 90 DAY WARRANTY NY C l EAN 7 VOX KN Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards a 4 and warrants to the original purchaser that this product is free from defects in materials and workmanship for Zs KA the period of ninety days from the date of purchase This warranty does not apply to damage due directly or NSS KY indirectly to misuse abuse negligence or accidents repairs or alterations outside our
Download Pdf Manuals
Related Search