Chamberlain 935CB User's Manual
Contents
1. CHAMBERLAIN Motion Detecting Control Panel FOR USE WITH GARAGE DOOR OPENERS MANUFACTURED AFTER JANUARY 1 1995 This door control contains a motion detector that will automatically turn on the light when it detects a person entering the garage This feature can be easily turned off for extended work light use Locate the door control within sight of the door at a minimum height of 5 feet 1 5 m where small children cannot reach and away from moving parts of the door and door hardware NOTE After installation an indicator light behind the cover will indicate proper connection If not lit the Lock and Light features will not function reverse wires to correct INSTALLATION The door control is typically attached directly to the wall For pre wired installations as in new home construction it can be mounted to a standard single gang box See illustrations If installing the door control adjacent to existing door controls be sure the detector switch is accessible 1 Disconnect power to the garage door opener 2 Strip 7 16 11 mm of insulation from one end of bell wire and connect to the two screw terminals on back of door control by color white wire to 2 and white red wire to the 1 3 Remove white cover by gently prying at slot in top of the cover with a small flat head screwdriver Fasten with 6ABx1 1 4 self tapping screws drywall installation or 6 32x1 machine screws into gang box as follows e Drill and i2. R OFFICE USE Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation 2007 The Chamberlain Group Inc 114A2398C All Rights Reserved
3. control is installed on an opener manufactured from January 1 1995 to May 15 1999 the following difference may apply If the light is on when the opener is actuated the light may go off for a moment then turn on again as the detector senses you Automatic Light Override Feature We recommend that you disable the motion sensor when using the opener lights as working lights Otherwise they will turn off automatically if you are working beyond the sensor s range Slide the Detector Switch on the right side of the door control down off then press the light button to control the lights Lock Feature Designed to prevent operation of the door from handheld remote controls However the door will open and close from the Door Control the Outside Keylock and Keyless Entry accessories To activate Press and hold the Lock button for 2 seconds The push bar light will flash as long as the lock feature is on To turn off Press and hold the Lock button again for 2 seconds The push bar light will stop flashing Normal operation will resume The Lock feature will also turn off whenever the Learn button on the motor unit panel is activated NOTICE To comply with FCC and or Industry Canada IC rules adjustment or modifications of this receiver and or transmitter are prohibited except for changing the code setting or replacing the battery THERE ARE NO OTHER USER SERVICEABLE PARTS Tested to Comply with FCC Standards FOR HOME O
4. er light on or off When the door is opened or closed the light will remain on for 4 1 2 minutes Press the Light button to turn it off sooner The Light button will not control the opener light when the door is in motion When using the opener lights as working lights we recommend that you first disable the motion sensor See Automatic Light Override Feature below When used with openers manufactured after May 15 1999 check the date on the opener panel the 4 1 2 minute interval can be changed to 1 1 2 2 1 2 or 3 1 2 minutes as follows Press and hold the Lock button until the light blinks about 10 seconds A single blink indicates that the timer is reset to 1 1 2 minutes Repeat the procedure and the light will blink twice resetting the timer to 2 1 2 minutes Repeat again for a 3 1 2 minute interval etc up to a maximum of four blinks and 4 1 2 minutes Automatic Light Feature The opener light will turn on automatically when a person enters the garage When a person walks in front of the door control the opener light will come on for five minutes then shut off This feature works by detecting body heat It is more sensitive in front of the door control than at its sides and works better as a person moves closer It may not work in temperatures around 100 F 38 C To disable this feature slide the Detector Switch on the right side of the door control down off Special note for older garage door openers If this door
5. nstall bottom screw allowing 1 8 3 mm to protrude above wall surface e Position bottom of door control on screw head and slide down to secure Adjust screw for snug fit e Install top screw with care to avoid cracking plastic housing Do not overtighten e Insert top tabs and snap on cover STANDARD WALL MOUNT To Replace Insert Top Tabs First Top Mounting Hole i Detector wi 24 Volt a Ss 22g Bell Wire OFF Terminal Screws Lag Bottom 24 Volt jo Mounting 2 Conductor Back View Hole Bell Wire To Replace Insert Top Tabs First Detector son Push Bar Cover Switch Lorr Model 935CB OWNER S MANUAL To prevent possible SERIOUS INJURY or DEATH from electrocution e Be sure power is not connected BEFORE installing door control e Connect ONLY to 24 VOLT low voltage wires To prevent possible SERIOUS INJURY or DEATH from a closing garage door e Install door control within sight of garage door out of reach of children at a minimum height of 5 feet 1 5 m and away from all moving parts of door e NEVER permit children to operate or play with door control push buttons or remote control transmitters e Activate door ONLY when it can be seen clearly is properly adjusted and there are no obstructions to door travel e ALWAYS keep garage door in sight until completely closed NEVER permit anyone to cross path of closing garage door NOTE The push bar may stick if the door control is no
6. t mounted on a smooth surface If a click is not heard when pressing the push bar loosen the two mounting screws or relocate the door control to a smoother surface 4 Standard installation only Run bell wire up wall and across ceiling to motor unit Use insulated staples to secure wire in several places Do not pierce wire with a staple creating a short or open circuit 5 Strip 7 16 11 mm of insulation from end of bell wire For quick connect terminals connect bell wire as follows white to white and white red to red For opener terminal screws connect white to 2 and white red to 1 OPENER TERMINAL SCREWS Push Bar 1 2 L 3 7 16 9 el gt E o a Strip wire 7 16 11 mm NS al k Opener Panel Antenna Loc Button Light Button QUICK CONNECT TERMINALS To release wire push in tab with screwdriver tip IY NOTE When connecting multiple door controls to the opener twist same color wires together Insert wires into quick connect holes white to white and red white to red or for terminal screws attach white to 2 and white red to 1 The automatic light feature will become functional 1 1 2 minutes after power is restored OPERATION Door Control Push Bar Press to open or close the door Press again to reverse the door during the closing cycle or to stop the door while it is opening Light Feature Press the Light button to turn the open
Download Pdf Manuals
Related Search