Casablanca Fan Company Star C28GXXM User's Manual
Contents
1. 84 CIRCUIT BREAKER TRIP BREAKER FOR THE before servicing it working on it or replacing CIRCUIT YOU WILL BE light bulbs WORKING ON e Never insert anything into the path of the fan eel blades while the fan is in operation Be e Never install a fan over a pool or spa e Never operate a fan that has been damaged in any way Contact Casablanca Fan Company ZZ EE by calling 1 888 227 2178 or contact your local authorized Casablanca dealer for assistance in obtaining service al L rsl Lo PN C2843001 AT0209 ESN Before mounting your Casablanca fan read the following helpful recommendations The location of the fan air circulation and fan size are all important factors to consider before installation Location Ceiling fans have practical uses in almost every room in your home We suggest you follow these mounting recommen dations as you decide where to install your Casablanca fan e For safety reasons the fan blades must be a minimum of 7 above the floor e Do not locate the fan in a doorway or above a swinging door e In any installation the tips of the blades must be at least 18 from the wall in order to provide sufficient clearance for the blades e In bedrooms fans work best when mounted above the foot of the bed e Over pool tables be sure to provide plenty of clearance to avoid damage from pool cues e In low ceiling loca2. METAL WASHER a 4 PER BLADE 4 PER BLADE 4 PER BLADE BLADE HARDWARE BLADE INSTALLATION Step 3 Assemble the blades to the motor using the blade screws rubber washers and metal washers BLADE SCREW amp WASHERS Hand tighten firmly RUBBER WASHER STAR STARLET NA HANGING THE FAN S Step 4 To hang the fan body in the canopy hold the fan g body firmly and insert the ball into the canopy opening Check that no wires were pinched Rotate the fan body until the slot in the nylon ball fits into the pin opposite the canopy opening CANOPY ELECTRICAL CONNECTIONS Step 5a Attach the fan wires to the ceiling fixture outlet box wiring by twisting the bare ends of the wires together and then securing with a wire nut Test that the connection is secure by pulling on the wire nut Connect in this order Step 5b Wiring Connections e GREEN leads from mounting plate and fan to GROUND conductor of power source Secure with wire nut e WHITE wire from fan to white NEUTRAL wire in ceiling fixture outlet box Secure with wire nut e BLACK power wire from fan to BLACK power wire in ceiling outlet box Secure with wire nut 3 GREEN WIRES WIRE NUT CANOPY HATCH INSTALLATION Step 6 Tuck the wires into the canopy with the wire nuts pointed upwards so that the WHITE and BLACK wires are on opposite sides of the canopy and all wires are clear of the canopy Opening S
3. ceiling fan installations if it is not a new box must be installed Casablanca extension poles are available for sloped or high ceiling installations e This ceiling fan requires a grounded electrical supply of 120 VAC 60 Hz and a minimum 15 amp circuit The maximum current requirement for the fan with light fixture is 1 48 amps Star 1 28 amps Starlet The fan uses about 85 amps 102 watts Star 65 amps 78 watts Starlet Maximum light current is 63 amps or 75 watts of lighting e Where wire nuts are employed be sure all bare wires are within the connectors When installing the canopy hatch make sure all wires are within the canopy and that no wires are being pinched For best performance and for your warranty to be valid use only genuine Casablanca blades light fixtures and accessories The blades in each pack are matched for equal FUSE BOX weight to assure smooth fan operation If more REMOVE FUSE FOR THE than one fan is being installed be careful not CIRCUIT YOU WILL BE to mix blades from different cartons WORKING ON e Inspect the contents of your carton for possible shipping or handling damage and report any such damage directly to your authorized Casablanca dealer e tis always a good idea to have an assistant to help with the installation e When cleaning painting or working near your fan be very careful of the fan and blades Always turn the power OFF to the ceiling fan 18 70
4. only No lighting wattage is included
5. ALLATION Proceed with installation as follows Step 1 Place the wires from the ceiling outlet box to one side of the crossbar mounting bracket Attach the bracket with ground wire and ridges down to the ceiling fixture outlet box with the mounting hardware included with the outlet box Tighten the screws firmly by hand only being careful not to bend the bracket by over tightening CAUTION To reduce the risk of personal injury use only the mounting hardware provided with the approved outlet box to install the crossbar mounting bracket CEILING CEILING FIXTURE WIRING OUTLET BOX CEILING FAN RATED GREEN GROUND WIRE j CROSSBAR A MOUNTING J oO BRACKET en ot RIDGE SIDE DOWN WASHERS 2 1 X 8 32 ROUND HEAD SCREWS 2 DS LAG SCREW AND WASHER 1 o STAR STARLET NA CANOPY HARDWARE CANOPY HATCH a CANOPY P CANOPY SCREW 4 oO CANOPY LOCK SCREWDRIVER CANOPY INSTALLATION Step 2 Attach the canopy to the crossbar mounting bracket with three of the 8 32 x 2 long canopy screws and canopy lock washers Tighten the screw firmly by hand only gt gt gt 2r gt Zau Note On sloped ceilings align the canopy opening towards the CROSSBAR top or room peak MOUNTING BRACKET CANOPY 1 mi CANOPY bi LOCK WASHER CANOPY SCREW CaS Ewean S BLADE SCREW RUBBER WASHER
6. CONTENTS INTRODUCTION ceeuese eee crete cee eee eee eee eters ee ewe eee oes ew eee eee ee see 1 MOUNTING RECOMMENDATIONS 2 eccccccsccccsaeaeeceeesee eee teeteeth ines teaw deena eesaee 2 PANUNGTALEATION pesis rin cece a eee heck eee r ee eee eek ee ee bee eee oe ese 3 CONTROL FEATURES VERSA TOUGH OPERATION 22222204424 homer Seep eon cree eee teebe estas eee a acess 10 TROUBLESHOOTING setereceseeesehiee ninni ee sabes bese teearteekawat as Raeeee he eeusaeenas 12 PRODUCT SPECIFICATIONS oa occu ence eae beet a ree de ee ere ee ee eee 13 READ AND SAVE THESE INSTRUCTIONS SAFETY FIRST Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product and proper installation therefore before attempting to install and operate your Casablanca fan read this owner s manual com pletely and carefully Retain this manual for future reference CAUTION To avoid possible electrical shock make certain that electricity is turned off at the circuit breaker or fuse box before attempting any installation procedure e All wiring must be in accordance with the National Electric Code ANSI NFPA 70 1993 and the appropriate local electrical codes The National Electric Code requires proper grounding as a precaution against electrical shock A qualified electrician should be consulted if you are unsure e This fan is designed to be installed on an existing electrical outlet box The outlet box must be UL Listed for
7. Fan works but light does not dim e The fan receiver is defective Replace fan receiver Fan works but light does not work The fan receiver is defective Replace fan receiver e The light socket is broken Replace socket e A lightbulb is defective Replace lightbulb NOTE In compliance with US Federal Energy Regulations this ceiling fan contains a device that restricts the light fixture to a maximum of 190 watts Exceeding that limit or the marked limit on this product may result in a fire hazard or improper operation STAR STARLET PRODUCT SPECIFICATIONS Model Name Sar Motor 172mm x 20mm Direct Drive Model Number C28GXXM Blade Span 52 Blade Iron Pitch 15 Dimensions A 11 8 caina Line D Bee Technology Versa Touch2 W 72 B 14 35 eee Ce 3 Lightbulb 1 75 watt halogen includes light fixture _ d ane pass x E Airflow 5 640 cfm Electricity Use 66 watts Weight 27 lbs Airflow Efficiency 84 cfm watt Model Name Starlet Motor 153mm x 12mm Direct Drive Model Number C29GXXM Blade Span 36 Blade Iron Pitch 15 No of Blades 3 Technology Versa Touch2 W 72 Lightbulb 1 75 watt halogen Dimensions A 11 7 Ceiling Line B 14 35 NOTE Dimension B 3 n includes light fixture _ lt and glass D 8 09 o Airflow 3 074 cf EE Electricity Use 50 watts Weight 20 lbs Airflow Efficiency 62 cfm watt Performance data is for fan
8. all your fan EXAMPLE 2 This slope is 32 This is the maximum slope that will allow the fan to hang Calculation of 32 d straight down Itis OK to install your Use the tear off Ceiling Angle Template card inserted in A PLE 3 this manual It provides you with a simple go or no go a This slope is more than 32 for installing your fan on a sloped ceiling Your fan will not hang straight down an adapter is necessary Contact your local Authorized Casablanca Dealer in regards to purchasing a Slope Ceiling Adapter STAR STARLET INSTALLATION INSTRUCTIONS Unpacking Before assembling and installing your ceiling fan remove all parts from the shipping cartons and check them against the parts listed here Before discarding packaging material be certain that all parts have been removed Setup Remove the fan body from the box and place the body of the fan on top of a cloth on a flat surface This will protect the fan body from being scratched during assembly DOWNROD amp BALL LOCKING BOLT MOTOR COUPLING ASSEMBLY IMPORTANT SAFETY INFORMATION BEFORE STARTING THE INSTALLATION OF YOUR CEILING FAN INSTALL THE THREADED DOWNROD INTO THE MO TOR COUPLING AND LOCK THE ASSEMBLY GROUND Prepare for fan installation as follows WIRE MOTOR Step A Route the wires from the motor through the WIRES PermaeLock downrod and ball assembly Tip The downrod has a ta
9. circuit breaker for at least 5 seconds Step 3 Turn the power back on at the circuit breaker and push the HIGH MED and LOW buttons in that order within 20 seconds Step 4 The fan should now function properly OR FUSE BOX 1 HIGH PRESS IN THIS ORDER TO SET NEW FREQUENCY 2 MED 3 LOW Geet TROUBLESHOOTING TIPS Please refer to this troubleshooting guide before requesting service or contacting your dealer for assistance PROBLEM POSSIBLE REMEDIES Fan will not start e Check the main circuit fuses circuit breakers and wall switch position Check all wire connections Make sure the power is turned off during this inspection e The 9 pin connector is not making good contact Check the 9 pin connector in the receiver mounted in the switch housing The battery is weak Install a fresh battery The fan receiver is defective Replace fan receiver e Check the frequency setting Turn the power off at the circuit breaker only for the fan that is not functioning Check that the jumper switches match in both the receiver and the transmitter Fan wobbles or shakes excessively e Be sure the canopy pin is set properly into the slot on the ball e Check that the bladeholders have not been bent during installation and the blades are balanced The hanger bracket and or ceiling outlet are attached too loosely Make sure the hanger bracket is attached tightly to the ceiling outlet box and the downrod assemb
10. duce the risk of electrical shock this fan must be installed with an isolating wall control switch CAUTION Do not use with wall dimmer WARNING To reduce the risk of fire or electric shock do not use this fan with any solid state speed control device Use only the control provided with this fan Step 12 Follow instructions for the type of transmitter control bracket you will be using TOGGLE SWITCH INNER MOUNTING HOLES SWITCH COVER PLATE CONTROL BRACKET Standard Light Switch Step A Remove the two screws holding the switch cover plate Do not remove the cover plate Step B Orient the control bracket as shown and line up the two inner mounting holes with those on the switch Step C Insert and tighten the screws using the provided screwdriver Wall Installation Step A Locate a 2x4 wall stud in a convenient location Step B Orient the control bracket as shown over the 2x4 stud Step C Insert the 1 wood screws in either the inner or outer mounting holes and tighten using the provided screwdriver 177 6 ROCKER LIGHT SWITCH OUTER MOUNTING HOLES go oN SWITCH COVER CONTROL PLATE BRACKET Rocker Light Switch Step A Break off the two tabs by pushing outward Step B Remove the two screws holding the switch cover plate Do not remove the cover plate Step C Orient the control bracket as shown and line up the two inner mounting holes with those on the switch Ste
11. he halogen bulb carefully cut off the end of the plastic sleeve the bulb comes in and hold the bulb by the plastic sleeve to screw it into the socket Step 10 Screw the 75 watt halogen bulb into the socket Do not touch the glass bulb with your fingers it is extremely important that the glass be clean If it is accidentally touched or dirty clean carefully with a tissue A dirty glass will cause the bulb to fail almost immediately HALOGEN BULB NOTE In compliance with US Federal Energy LIGHT ee Regulations this ceiling fan contains a device SOCKET that restricts the light fixture to a maximum of HALOGEN 190 watts Exceeding that limit or the marked BULB limit on this product may result in a fire hazard or improper operation Step 11 Position the indentations in the outer rim of the glass shade so that they line up with the tabs on the inside surface of the fan light fixture rim Carefully lift the glass shade up inside the light fixture as far as it will go Rotate the shade in a clockwise direction until it is held tightly in place by the three tabs TAB TIP At first the shade is a very loose fit in the fixture and can be wiggled a little from side GLASS SHADE to side It is a great help when rotating the glass shade to wiggle it at the same time W 72 W 72 Control Control Holder Wood Screw Screw Screw 6 32 X 6 32 X 1 1 2 2 2 SAFETY FIRST To re
12. ly is secured firmly e The downrod is attached to downrod base too loosely Make sure all the screws are securely tightened Fan is noisy during operation e Check and tighten the light fixture retaining screws glass shade screws and or lightbulb s Tighten the canopy screws and mounting plate assembly Make sure the wire nuts inside the canopy and switch housing are not touching the metal parts and that they have not fallen off the wire splices Tighten as necessary e Tighten the blade holders to the flywheel or direct drive motor and the blades to the bladeholder screws e Make sure all screws in the motor housing are snug but not overly tight Fan does not run on low speed If fan is new it may need to be broken in Run at high speed for several days Battery life is short e Replace with alkaline batteries Light works but fan does not work e The fan wires are not connected properly Fan and light run only on full speed e The fan receiver is defective Replace fan receiver Fan is missing one speed e The fan receiver is defective Replace fan receiver Fan does not change speed but light works e The fan receiver is defective Replace fan receiver Reverse does not work The fan receiver is defective Replace fan receiver Fan starts working by itself e There is frequency interference Change frequency Fan operates only when transmitter is close e Check that antenna wire is not touching metal plate
13. p D Insert and tighten the screws using the provided screwdriver NOTE The wall anchors and 6 32 x 1 screws may be used in situations where mounting to a stud is not possible Use the inner mounting holes After securing the anchor discard the anchor s pointed screws and use the 6 32 decor ovalhead screws supplied ANCHOR ___ diaaa PANHEAD n SCREW DRYWALL ANCHOR WOOD DECOR OVALHEAD SCREW SCREW 1 6 32 X 1 VERSAel OUCH2 Fan Control To start the fan Press the selected speed button to run the fan at the desired speed Send Signal LOW Low speed MED Medium speed HIGH High speed LED To turn off the fan press the FAN OFF button SED Airflow Direction To reverse the airflow press the REVERSE button REVERSE operates at any speed LOW whether the fan is on or off The fan returns to its set speed after reversing Light Control Turn the light on or off independently from the fan by pressing the LIGHT button If you press the button for more than 0 7 seconds it becomes a dimmer The light varies from bright to dim over approximately 8 seconds If you continue to hold REVERSE the LIGHT button this sequence will reverse when the light reaches its brightest or dimmest level Release the button when the desired level is reached Memory Feature The last light fuction and fan speed will resume when power is turned back on Auto Resume Quick pressing less than 0 7 seconds on off operation of
14. pered thread that is designed to lock com DOWNROE pletely when correctly installed TAPERED THREAD BALL Step B Thread the downrod into the motor coupling and ASSEMBLY turn it clockwise until it stops turning ensuring that the pole has bottomed out LOCKING BOLT Step C Securely tighten the locking bolt to ensure safe operation of your fan MOTOR COUPLING CAUTION Failure to fully lock in the down rod before securely tightening the locking bolt may cause the fan to separate from the downrod during normal operation WIRE NUT 4 CROSSBAR MOUNTING BRACKET x 8 32 ROUND HEAD SCREWS 2 EY FLAT WASHER 2 e CO LAG SCREW AND WASHER 1 GETTING STARTED Installing a New Ceiling Fixture Outlet Box If you do not have an existing fixture located where you wish to place your Casablanca fan an approved ceiling fixture outlet box must be installed and wired Warning To reduce the risk of fire electrical shock or personal injury mount to outlet box marked acceptable for ceiling fan support using the mounting hardware provided with the outlet box Using Existing Ceiling Fixture Outlet Box After turning the power OFF at its source either circuit breaker or fuse box lower the old fixture and discon nect the wiring Check the ceiling fixture outlet box to be sure that it is marked Approved for ceiling fan mount ing If it is not a new box must be installed CROSSBAR MOUNTING BRACKET INST
15. tep 7 Install canopy hatch with the last canopy screw and lock washer To do this tilt the fan body away from the hatch opening Tighten the screws firmly by hand only Step 8 Straighten the fan then check to ensure that there is no movement between the canopy and ceiling or Hang Tru ball and top support shaft CANOPY SCREW CANOPY HATCH LOCK A CANOPY WASHER e X d N i A eee TILT THE FAN TO INSTALL LAST CANOPY SCREW ATTACHING THE LIGHT FIXTURE Step 9a Before getting started remove the rubberband from the plug connector Step 9b Install two of the three light adapter screws into the light adapter plate Thread the plug connec tor through the hole in the center of the light adapter plate Step 9c Align the two key slot holes with the two screws and rotate the light adapter plate clockwise Install the third light adapter screw and securely tighten all three screws Tighten the screws firmly by hand only Step 9d Connect the light fixture plug to the plug from the bottom of the fan Step Ye Align the light fixture to the three screw holes on the light adapter plate using the light fixture screws then attach the light fixture to the fan STEPS 9a 9c LIGHT ADAPTER SCREWS LIGHT ADAPTER PLATE STEPS 9d LIGHT ee FIXTURE STEPS 9e LIGHT FIXTURE SCREWS me STAR STARLET NA INSTALLING THE HALOGEN BULB IMPORTANT When installing t
16. the LIGHT button maintains the desired brightness level set previously Note All fans leave the factory set to 00000 You will only have to change the dip switch settings in the remote if you are using more than one fan in the same area and want to control them separately Step 1 At the circuit breaker or fuse box turn the power off for the fan you want to change Step 2 Open the battery door of the Versa Touch control and remove the batteries Step 3 Change the dip switch settings assuring that they are different from the previously installed Versa Touch fan Step 4 Re install the batteries and the battery door on the control Step 5 At the circuit breaker or fuse box turn the power back on for the fan whose frequency you are changing 10000 Step 6 Within 20 seconds of restoring power push the HIGH MED and LOW buttons in that order LIGHT VERSA TOUCH 2 CONTROL BACK DIP SWITCH SET TO 01001 WARNING ls enc Do not turn the power off at the circuit breaker then Note You may want to label your controls to assure back on for the previously installed Versa Touch2 you do not mix them up fan s as you may inadvertently change the frequency settings for it as well If the fan is not functioning after installation Step 1 Check to make sure that batteries are installed cor rectly in the control Step 2 Turn the power off to the fan from the
17. tions our optional low ceiling adapter LCS available at extra cost can be used to gain 31 2 not applicable to Stealth Venus and Silhouette series e In kitchens be sure to allow for open cupboard doors to clear the fan blades e Do not install a fan close to or over a pool or spa High humidity combined with corrosive P gases will destroy the finish and warp the blades FAMILY CEIS ROOM Fan Size Variable fan speed capability permits the use of a full size 52 fan even in smaller rooms For very large rooms two fans may be needed Suggested Extension Pole Lengths Be anA Ceiling Height Pole Length EXTENSION ANGLE 32 Standard POLE Standard 6 12 12 18 2 30 48 BLADES MUST BE A MINIMUM OF 7 ABOVE THE FLOOR 7 MINIMUM When to Use Extension Poles For best performance and best appearance an extension pole should be used with your Casablanca fan when installing on high cathedral ceilings or sloped ceilings Casa blanca offers standard poles in increments of 6 up to 5 See your Authorized Casablanca Dealer for details O ake N ON RN S EA WA LAN S NS N N NOTE Fan may wobble or vibrate if pole length is not long enough and inside blade is too close to downslope or side wall Extending pole length will usually solve problem EXAMPLE 1 This slope is less than 32 It is OK to inst
Download Pdf Manuals
Related Search