Home

Canon i900D Printing Guide

1. Te Print all 2 Use the A W buttons to select Specify images Maintenance and then press the OK button A Print nets The maintenance menu is displayed yout DPOF GT Maintenance OK Select 3 Use the A W buttons to select Auto head Maintenance S Nozzle check align and then press the OK button pes ed The confirmation screen is displayed Auto head align Manual head align Thick paper Contrast Do you want to start 4 Use the A W buttons to select Yes and pe A then press the OK button Yes A pattern is printed and the print head is No automatically aligned Load plain paper Note When Automatic Print Head Aligning Cannot Execute Correctly When automatic print head aligning cannot execute correctly the power lamp flashes orange 11 times and the message Failed to align print head is displayed on the LCD Please follow the procedure below 1 Press the Resume button to clear the error 2 Open the front cover and check if there is ink left If there is no ink left replace the ink tanks See Replacing Ink Tanks on page 35 3 Print the nozzle check pattern to verify that the print nozzles are clean See Printing the Nozzle Check Pattern on page 38 4 Move the printer so that the paper output is not in direct sunlight and try automatic print head aligning again 5 If the error persists adjust the print head manually See Adjusting the Print Head Manually
2. amp Ink is almost empty Continue anaoa No 34 Empty ink tank with an empty ink tank When printing is finished replace the ink tank immediately If you continue printing with an empty ink tank it will be a cause of trouble When Low Ink is Detected When printing starts the message is displayed on the LCD indicates ink low Obtain a replacement tank as soon as possible To continue printing select Yes and then press the OK button To cancel printing select NO and then press the OK button Replacing Ink Tanks When ink tanks run out of ink replace them using the following steps 1 Ensure that the printer is on and then open the front cover The print head holder moves to the center 2 Remove the empty ink tank 1 Push the tab and remove the ink tank Do not touch the lock lever remove only the ink tank D Important e Handle ink tanks carefully to avoid staining clothing or the surrounding area e Discard empty ink tanks according to the local laws and regulations regarding disposal of consumables 3 Prepare a replacement tank 1 Unpack the new ink tank and pull off the orange tape 2 Remove the orange protective cap from the bottom of the ink tank and discard it e Do not squeeze the side of ink tanks as this may cause the ink to leak out and stain your clothes and hands e Do not re attach the protective cap once you have removed it e Once the protective cap is re
3. 1 Ensure that the digital camera is turned off 2 Connect the digital camera and the printer with the USB cable that came with the digital camera The digital camera should turn on automatically If not turn it on manually 25 4 Start printing using the print function of the digital camera The message of Digital camera connected is displayed on the printer LCD Digital camera connected 1 Display the image you want to print in the Replay mode If the camera will not change to the Replay mode refer to your digital camera user s manual s instructions for changing the camera to the Replay mode E will display on the LCD display of the digital camera when the printer is correctly connected 2 Press the SET button to display the Print menu 3 Select Style and specify the paper size Bordered or Borderless printing and date printing On or Off 4 After specifying the style specify a number of copies select Print and then press the SET button Notes For the digital camera operation and troubleshooting refer to your digital camera manual For print error message refer to Cannot Print Properly from the Digital Camera on page 45 For the digital video camcorder operation print error messages and troubleshooting refer to your digital video camcorder manual You can make the following prints directly from a digital camera A standard print from the image displayed in the sin
4. 1 Use the A W buttons to select Quiet mode and then press the OK button The Quiet mode setting screen is displayed 2 Use the A W buttons to select On and then press the OK button 33 Replacing an Ink Tank When replacing an ink tank check the model number very carefully The printer will not print properly if the wrong ink tank is used or installed in the incorrect position With this printer ink tanks must be installed from the right in the order indicated below Magenta BCI 6M Q Black BCI 6BK U Photo Magenta BCI 6PM Photo Cyan BCI 6C 6 Yellow BCI 6Y 6 Q Photo Cyan BCI 6PC Photo 6 Knowing When to Replace Ink Tank If an ink tank needs replacing the Power lamp will change from green to orange and flash four times as soon as printing begins It is important to identify the empty tank using the LCD and replace it Note Should missing characters or white streaks appear despite sufficient ink levels See When Printing Becomes Faint or Colors are Incorrect on page 37 The following message appears on the LCD when ink is empty Printing will resume as soon as ink tank is replaced and the front cover is closed Notes Too isd The ink tank with symbol is out of ink o T Ymae Replace with a new ink tank aoa DPen k ak Press the Cancel button to cancel the current print job e Press the Resume button to resume printing
5. 10 11 12 3 Resume Button Press to resume printing after resolving a printer problem Menu Button Displays menus See Menu Displays on page 3 Settings Button Allows you to set the Paper Size Paper Type Bordered Borderless printing printing with the date etc See Specifying the Paper and Optimizing Images on page 22 Trimming Button Allows you to trim the image being displayed when Trimming is displayed on the screen See Printing a specified area Trimming on page 15 OK Button Allows you to make a selection For example selecting an image to be printed selecting a menu item or other setting A V Buttons Press to select an item in menus or options to specify the number of copies to print or print settings 9 lt p Buttons Press to scroll through the options or to scroll the screen 10 Photo Viewer Button Press to start exit the Photo Viewer This button is also used to save the data stored in the memory card on the hard disk of the computer For more details about Photo Viewer see Using Photo Viewer on page 27 11 Print Button Press to start printing according to the settings displayed on the LCD 12 Cancel Button Press to cancel the settings you have made If this button is pressed during printing the printer aborts printing 13 Q Buttons Press to enlarge or reduce the image being displayed Pressing this button in trimming mode allows you to enlarge red
6. 4 Click Complete The selected read write attribute is saved USB Memory Card Settings 29 30 Ensure that the printer and the computer are turned on Start the BJ Utility 1 Ensure that no memory card is inserted in the card slot If a memory card is inserted in the card slot remove it See Removing a Memory Card on page 8 2 Select Applications from the Go menu and then double click the BJ Utility icon Specify the read write attribute 090 Canon BJ Utility Change the read write attribute Set the read write attribute for the card slot of the BJ printer Select the mode and click OK Read only mode This mode disables writing on the Memory Card O Read write mode This mode allows both reading and writing on the Memory Card Start ImageCapture when a card is inserted F Do not display this dialog when a card is inserted 1 Specify the read write attribute Read only mode The card slot is used only for read Be sure to select this mode when printing images Read write mode The card slot is used as the memory card drive of the computer Image data can be written into the memory card 2 Click OK The selected read write attribute is saved Changing the Language Displayed You can change the language displayed on the LCD 1 Turn on the printer 2 Select Maintenance from the Menu 1 Press the Menu button amp Print all
7. Turn on the printer Open the card slot cover Install the memory card in the card slot e If you use a CompactFlash CF card or Microdrive insert it as far as it will go as shown left e Ifyou use a SmartMedia card insert it until it stops with its end projecting as shown left e If you use a Memory Stick insert it until it stops with its end projecting as shown left e Ifyou use an SD card or MultiMedia card insert it until it stops with its end projecting as shown left Removing a Memory Card Note If you use the printer connected to your computer follow the instructions for removal of the memory card from the computer For the procedure refer to the on screen User Guide 1 Ensure that the Indicator lamp is not flashing then remove the memory card Removing the memory card or turning off the printer while the Indicator lamp is flashing can damage the data stored in the memory card If you use CompactFlash CF card or Microdrive press the card eject button to remove the card Indicator lamp If you use a SmartMedia card hold the exposed portion of the memory card with your fingers to remove the memory card e If you use a Memory Stick hold the exposed portion of the memory card with your fingers to remove the memory card Ifyou use an SD card or MultiMedia card hold the exposed portion of the memory card with your fingers to remove the memory card Printing Photogr
8. 2 Use the A W buttons to select Gai Specify images Maintenance and then press the OK button Pll fare The maintenance menu is displayed yT MAMiaRE OK Select 3 Select a language for display Dery Henning 1 Use the A W buttons to select Languages Auto head align and then press the OK button Manual head ali i i i mk sala Ld The language selection screen is displayed Contrast Quiet mode Languages 2 Use the lt gt A YW buttons to select a Manguagess language and then press the OK button BAB Nederlands The menu selection items and messages English mm Espa ol i i i EFTS RRA will be displayed in the language you select Deutsch Svenska Francais OK Select 31 Adjusting Contrast of the LCD You can adjust contrast of the LCD if it is too high or too low 1 Turn on the printer 2 Select Maintenance from the Menu 1 Press the Menu button KE Print all 2 Use the A W buttons to select Gai Specify images Maintenance and then press the OK button Print index E Select layout The maintenance menu is displayed DPOF QT Maintenance OK Select 3 Select Contrast Maintenance ozs check 1 Use the A W buttons to select Contrast Head cleaning and then press the OK button leani i ie di PAren The Contrast setting screen is displayed Manual head align Thick paper Contrast OA 2 Pre
9. Supports TYPE I TYPE II 3 3V or 5V T SmartMedia Card Supports 3 3V card only 1MB and 2MB cards not supported O Memory Stick QO Secure Digital SD Card QO MultiMedia Card Other memory cards can be used through the adapter which is compatible with the above NI Important Images stored in a memory card not supported by the digital camera may fail in loading or be damaged For types of memory cards supported by the digital camera refer to your digital camera user s manual e To format a memory card use the digital camera Memory card data formats may not be compatible with computer specific formats e Images edited on the computer may result in improper printing e Please use only one type of memory card at a time If you use more than 2 types of memory card at the same time you could lose data or data could be read incorrectly from the cards Inserting a Memory Card Notes e When Read write mode is selected in the Memory Card Utility Windows or BJ Utility Macintosh neither printing nor maintenance can be done After using the card slot as the memory card drive of the computer be sure to select Read only mode again See Setting up the Card Slot as the Memory Card Drive of the Computer on page 29 e If you used a computer to edit or process the data stored in the memory card be sure to print images from the computer Using the operation panel to print images may result in improper printing
10. size 101 6x152 4mm 127x177 8mm M ESettings Check 2 Press the OK button After the paper size is set Paper type tab is displayed Paper Type 2 Photo Paper Pro Photo Paper Plus Glossy Plain paper Settings Check 3 Repeat the same steps to set the necessary items 2 Finalize the Settings 1 When you have completed the necessary settings press the Settings button The Setting confirmation is displayed 101 6 x 152 4mm Photo Paper Pro Borderless YYYY MM DD High quality Exif Print Noise reduction off OK Set 2 Confirm the settings and press the OK button The screen returns to the state before the Settings button was pressed 22 Paper Size 101 6x152 4mm 127x177 8mm M ESettings Check Paper Type Photo Paper Pro Photo Paper Plus Glossy Plain paper Settings Check Borderless Printing 3 Borderless Bordered Settings Check Date Date off YYYY MM DD MM DD YYYY DD MM YYYY Settings Check Print Quality High quality Standard quality Settings Check Photo Optimizer Exif Print Vivid Photo POP VP POP Photo optimizer off Settings Check Noise Reduction Noise reduction off Noise reduction on Settings Check E Other Setting Items E Page Size Select the paper size for the print job E
11. Paper Tray lowered paper cannot be fed from the Sheet Feeder Turn the dial to use the Turn the knob on the Photo Paper Tray to change the way to feed sheet feeder paper The size of paper loaded in the Photo Paper Tray may be different from the paper size selected on your digital camera or the operation panel of the printer When printing from the digital camera change the paper size setting of the digital camera to the size of paper loaded in the Photo Paper Tray When using the digital camera that cannot select the paper size or when printing from a memory card change the setting on the operation panel of the printer Error code Turn off the printer remove the power cord plug from the outlet plug the power cord back in and then turn on the printer again If the same error persists contact a Canon service representative Note Adjusting the Print Head Manually If the automatic print head adjustment does not work or if you wish to adjust the print heads manually follow the procedure below 1 With the printer on load two sheets of A4 plain paper in the printer 2 Press the Menu button 3 Use the A V buttons to select Maintenance and then press the OK button 4 Use the A W buttons to select Manual head align and then press the OK button do you want toprint 5 Use the A W buttons to select Yes and then press the OK button the print head alignment pattern ya 6 Ea message of Did the
12. button The Photo Viewer is terminated forcibly in the following cases e When a compatible digital camera or digital video camcorder is connected e When Read write mode is selected in the Memory Card Utility Windows or BJ Utility Macintosh e When a USB cable is disconnected Saving the data stored in the memory card to the hard disk of the computer e The image data JPEG TIFF format movie data AVI MPEG or sound data WAVE stored in the memory card in the card slot can be saved on the hard disk of the computer Keep pressing the Photo Viewer button on the operation panel for 3 seconds or longer Saving of the image data starts and the name of the file currently being saved and the name of the destination folder are displayed in the Photo Viewer window e If you press the Cancel button during the save operation the save operation will be stopped e The images will be saved in the location specified below A folder will be created with a name and the date of the images were saved YYYY_MM_ DD Windows XP Windows 2000 Windows Me My Pictures folder Windows 98 My Document folder Mac OS X 10 2 1or later Pictures folder Mac OS 9 0 9 2 Desk Top 28 Setting up the Card Slot as the Memory Card Drive of the Computer The card slot of the printer can also be used as the memory card drive of the computer N Important To use the card slot of the printer as the memory card drive of the computer the printer must b
13. on page 43 41 Troubleshooting Let s take a look at countermeasures against troubles which may occur during use of the printer Note Here we will discuss errors indicated on the LCD problems that might occur during direct printing from the digital camera and problems that are also likely to occur while using the Photo Viewer If you cannot find the symptom corresponding to a certain problem refer to the User s Guide A Message is Displayed on the LCD on page 42 Ink does not come out Printing is Blurred Colors are Wrong White Streaks on page 44 Printed Surface is Scratched on page 44 Cannot Print Properly from the Digital Camera on page 45 An Error Message is Displayed While Using the Photo Viewer on page 46 A Message is Displayed on the LCD If a message is displayed on the LCD take the corresponding countermeasure described below Message Try This No images Image data edited processed on the computer should be printed from the computer not from the camera Waste ink tank almost full Press the Resume button to recover from the error You can print images for a while but you cannot print any more image when the waste ink tank becomes full Contact a Canon service representative Read write mode enabled The memory card utility started on the computer has write enabled the card slot When the card slot is write enabled the printer cannot print images When you
14. page 31 gt Printing Flow This is the procedure for printing images from the memory card inserted in the card slot of the printer Step 1 Turn on the Printer Step 4 Selecting the Print Mode Print an image Specify Image Select layout Prints the image displayed Specify how many copies to Prints the specified image in on the LCD print for each image the specified layout Borderless or Bordered x2 x4 x8 postcard album Display the Image to Print Press the Menu button wv Select Specify images Select Select layout from from the Menu the Menu Specify the number of Select a Layout copies to print for each Images Select the image to print wv Step 5 Change Confirm Print Settings and Start Printing Confirm the Print Change the Settings Setti ngs 101 6 x 152 4mm Photo Paper Pro Print an image x 4 gt Settings gt Sedat Current settings button YYYY MM DD 101 6x152 4mm High quality Photo Paper Pro Exit Print derless q OK button g Noise reduction off OK Set Settings Change Print Print After setting the Paper Size Paper Type and Bordered Borderless printing press the OK button See Change the settings on page 10 Using a Memory Card Let s take a look at different types of memory cards and how to insert and remove them Memory Cards Supported by this printer Supported memory cards are as follows QO CompactFlash CF Card Microdrive
15. press the OK button Do not perform any other operations until the print head cleaning finishes This takes about 50 seconds Note After print head cleaning finishes After print head cleaning finishes print the nozzle check pattern to verify that the print head nozzles are clean See Printing the Nozzle Check Pattern on page 38 When ink is low the nozzle check pattern is not printed correctly See Replacing Ink Tanks on page 35 If the print quality remains poor repeat head cleaning 3 times If the print quality still remains poor perform head refreshing See Print Head Deep Cleaning on page 40 39 Print Head Deep Cleaning If print quality does not improve by standard print head cleaning try print head deep cleaning which is a more powerful process Print head deep cleaning consumes ink so perform this procedure only when necessary 1 Ensure that the printer is on 2 Print Head Deep Cleaning 1 Press the Menu button amp Print all 2 Use the A W buttons to select Gi Specify images Maintenance and then press the OK button a Print index The maintenance menu is displayed B Select layout DPOF QT Maintenance OK Select Mai Nozzle check Head cleani pet m 3 Use the A W buttons to select Deep farta paan eo cleaning and then press the OK button anual head align k R Thick paper The confirmation screen is displayed Contrast E Deep cleani
16. 02 2 Use the A W buttons to specify the number of copies to print 3 Repeat steps 1 and 2 and specify the number of copies for each image you wish to print 4 Press the OK button The print confirmation screen is displayed Trimming IF Note For each image selected you can also set the area to print using the Trimming function Refer to Printing a specified area Trimming 4 Start printing 1 Confirm the print settings To change any of the settings press the Settings button See Specifying the Paper and Optimizing Images on page 22 Ga Specify images Current settings 101 6x152 4mm Photo Paper Pro Borderless YYYY MM DD Settings Change Print Print 2 Press the Print button The specified number of copies for each image will be printed E Printing a specified area Trimming When Trimming is displayed below Specify images Select layout and Printing an Image the image displayed can be trimmed Note Please trim the image after specifying Paper Size Paper Type Borderless Bordered on each settings screen If you change the settings after trimming the image the trimmed selection will be lost 1 Set the Trimming Mode 1 Display the setting screens for Specify images Select layout and Printing an Image See Printing an Image Displayed on the LCD on page 9 See Specifying how many copies to print for each image on page 14 See S
17. Canon BUBBLE JET PRINTER 1905D 1900D Direct Printing Guide dp Printing Flow Printing Photograph Loading Paper Printing Maintenance Table of Contents Operation Panel and Menu Display 1 4 Using a Memory Card 6 9 11 Printing Images from a Memory Card 14 Specifying how many copies to print for each image 14 Printing all images N Printing an Image List Print Index 18 Specifying the layout AO Printing According to the Settings Made on the Camera DPOF Printing 20 Specifying the Paper and Optimizing Images 22 Printing Photographs Directly from a Digital Camera 24 Other Useful Functions 27 Replacing an Ink Tank 34 37 42 Troubleshooting 6 Pls sneer Exif Print E DIRECT PictBridge B 0A7 2791 V01 Operation Panel and Menu Display The names and functions of the controls on the operation panel how to display the menus and the items in the menus are discribed below Operation Panel Names and Functions 4 GF 7 9 4 5 6 7 8 1 Power Button Press to turn the printer on or off 2 Power Lamp Off the printer is turned off Green the printer is ready to print Flashing green the printer is preparing to print or is currently printing Flashing orange an error has occurred and the printer is not ready to print Flashing orange and green alternately an error has occurred that may require a service call
18. E Cannot Print Properly from the Digital Camera The following messages may be displayed on the cameras or camcorders when images are printed directly Take the appropriate action to correct the error This section describes errors that can occur when you connect a Canon Bubble Jet Direct compatible digital camera to the printer Notes Images can be printed directly from a PictBridge or Canon Bubble Jet Direct compatible digital cameras and digital video camcorders connected to this printer If the connected digital camera or digital video camcorder is not supported by this printer the Power lamp on the printer will flash nine times If this happens disconnect the connection cable and press the Resume button If the operation time or data transmission time is too long a communication time error may occur and no more images can be printed If this error occurs disconnect the camera connection cable press the Resume button and then connect the cable once again The digital camera should be turned on automatically If not turn it on manually A low ink warning is not displayed on the digital camera For more details also refer to the user s manual for the digital camera or digital video camcorder Error message on Try This camera Printer in use Images are printed from the computer Wait until printing ends Printer warming up Wait until warm up ends No Paper Load the paper in the printer and pr
19. Paper Type Select the paper type If you select Plain paper Borderless printing cannot be done E Borderless Print Borderless Prints on the whole paper without a border Bordered Prints with a border E Date YYYY MM DD Prints the date the photo was taken in the format YYYY MM DD 2003 10 22 MM DD YYYY Prints the date in the format MM DD YYYY 10 22 2003 DD MM YYYY Prints the date in the format DD MM YYYY 22 10 2003 Date Off Does not print the date the photo was shot E Print Quality Select the print quality E Photo Optimizer Exif Print 0000000 Optimizes photos based on the information at the time the photo was taken with a digital camera compatible with Exif 2 2 Vivid Photo Selects the Vivid Photo function Greens and blue are printed more brightly is used POR eesclcastaneeek Photo Optimizer PRO function automatic correction of image brightness and color combinations is used together VP POP vcen cage 3 Vivid Photo function and Photo Optimizer PRO function are used Photo optimizer off No photo optimization functions are performed E Noise Reduction If Noise reduction on is set digital camera noise which may be seen in dark areas or areas such as sky is reduced 23 Printing Photographs Directly from a Digital Camera Connecting a digital camera or digital video camcorder to the printer allows you to print captured i
20. aining DPOF information inserted in the printer press the Menu button 2 Use the A W buttons to select DPOF and then press the OK button 3 Start printing 1 Confirm the print settings To change any of the settings press the Settings button See Specifying the Paper and Optimizing Images on page 22 Current settings 101 6 x 152 4mm Photo Paper Pro Borderless Settings Change Print Print 2 Press the Print button The images will be printed according to the DPOF information on the memory card 21 Specifying the Paper and Optimizing Images You can use the Settings button to set the following items Paper Size or Type Bordered or Borderless print and Date format E Settings Menu Display Displaying an image on the LCD 001 023 100 0001 amp Settings Current settings 101 6x152 4mm p Settings button p dade Borderless YYYY MM DD Cancel Back OK Print Settings Change y p 3 F Settings button Displaying the print confirmation g screen on the LCD AA E Print an image x 4 Paper Size Current settings 10 101 6x152 4mm Photo Paper Pro Borderless YYYY MM DD Settings Change Print Print 101 6x152 4mm 127x177 8mm p Settings button p M Settings Check Properties screen m How to Make Settings 1 Select an item to set Paper Size 1 Use the A W buttons to select the paper
21. aph Let s select an image from the images stored on the memory card of the digital camera and print it Printing an Image Displayed on the LCD 1 Turn on the printer 2 Load the Paper See Loading Paper on page 11 3 Insert the memory card in the card slot See Inserting a Memory Card on page 6 The stored image is displayed on the LCD 001 023 100 0001 OK Print 4 Select the image to print a Te KE ON EX ORO J D Wer Print Cp OS iC 5 Confirm the settings fa Print an image Settings Change Print Print x 1 a gt Current settings 10 101 6x152 4mm Photo Paper Pro b Borderless YYYY MM DD fa Print an image Settings Change Print Print Current settings 1 High quality q Exif Print Noize reduction on xLi Ow Note You can also set the area to print using the Trimming function See Printing a specified area Trimming on page 15 1 Using the lt p buttons select the image to print 2 Press the OK button The print confirmation screen is displayed 1 Confirm the printer settings On the first screen the Paper Size Paper Type Bordered Borderless printing status and whether or not to print the date are displayed 2 Press the p button On the second screen the settings for Print Quality Photo Optimizer and Noise Reduction are displayed 6 C
22. ccording to the Settings Made on the Camera DPOF Printing on page 20 Select Maintenance Nozzle check Deep cleaning Head cleaning A Auto head align Deep cleaning Manual head align Auto head align Thick paper Manual head align Vv Contrast Thick paper Quiet mode Contrast Languages Nozzle check Prints a check pattern to ensure that ink is output correctly or that the print head is aligned properly See Printing the Nozzle Check Pattern on page 38 Head cleaning Cleans the print head when nozzles are clogged See Print Head Cleaning on page 39 Deep cleaning If print quality does not improve after standard head cleaning use Deep Cleaning See Print Head Deep Cleaning on page 40 Auto head align Aligns the print head automatically See Aligning Print Head Auto head align on page 41 Manual head align Aligns the print head manually See Adjusting the Print Head Manually on page 43 Thick paper Use the Thick Paper setting if white streaks appear on the printed page or the printed surface is scratched See If the printed surface is still scratched on page 44 Contrast Adjusts the contrast of the LCD See Adjusting Contrast of the LCD on page 32 Quiet mode Reduces the printing noise See Reducing the Sound of Printer Operation on page 33 Languages Sets the Language displayed on the LCD See Changing the Language Displayed on
23. d OK Select 3 Start printing 1 Confirm the print settings To change any of the settings press the Settings button See Specifying the Paper and Optimizing Images on page 22 E Print index Current settings 2 Use the A W buttons to specify the number of copies to print Plain paper YYYY MM DD Settings Change Print Print 3 Press the Print button A list of all images saved on the memory card will be printed 18 Specifying the layout You can print the specified image in the specified layout Borderless or Bordered x2 x4 x8 postcard album Bordered o Borderless Postcard i Prepare to print 1 Turn on the printer and load the paper See Loading Paper on page 11 2 Insert the memory card into the card slot See Inserting a Memory Card on page 6 A stored image is displayed on the LCD Select the print mode from the Menu 1 Press the Menu button The menu listing is displayed amp Print all a Speuity images Print index El Select layout DPOF GT Maintenance OK Select Specify the layout Borderless x2 T OK Choose images 2 Press the OK button 2 Use the A W buttons to select Select layout and then press the OK button The screen for specifying
24. d No then press the OK button The nozzle check pattern is printed Load plain paper 5 Examining the nozzle check pattern Examining the Nozzle Check Pattern The nozzle check pattern should appear as follows when ink is discharged properly Examine the nozzle check pattern output by the printer 1 White stripes in this pattern require running print head cleaning When white stripes appear See Print Head Cleaning on page 39 2 Unevenness in this pattern indicates the print head requires alignment When lines are uneven When lines are even See Aligning Print Head Auto head align on page 41 38 Print Head Cleaning Clean the print head if you suspect that the nozzles might be clogged Cleaning the print head consumes ink so perform print head cleaning only when necessary 1 Ensure that the printer is on 2 Print Head Cleaning 1 Press the Menu button amp Print all 2 Use the A W buttons to select Specify images Maintenance and then press the OK button eu ak The maintenance menu is displayed DPOF Yf Maintenance OK Select Nozzle check Head cleaning 3 Use the A W buttons to select Head Pind sane dl cleaning and then press the OK button Manual head align Thick paper Contrast The confirmation screen is displayed Do you want to start Head Cleaning Yes __ _______ 4 Use the A W buttons to select Yes and No then
25. e connected to the computer and the Memory Card Utility Windows or BJ Utility Macintosh must have been installed in the computer If the utility is not installed install it following the installation procedure explained in the Quick Start Guide e When Read write mode is selected neither printing nor maintenance can be done After you are finished with using the card slot as a memory card drive for your computer be sure to select Read only mode again Windows 1 Ensure that the printer and the computer are turned on Open the USB memory card setup window 1 Ensure that no memory card is inserted in the card slot If a memory card is inserted in the card slot remove it See Removing a Memory Card on page 8 2 Select All Programs or Program from the Start menu Next select Canon Utilities Memory Card Utility and then USB Memory Card Settings The USB Memory Card Settings window appears 3 Specify the read write attribute 1 Click Next The Read write attribute setting window appears 2 Specify the read write attribute Perce oe etc pi eC Read only mode 5 The card slot is used only for reading Be sure to select this mode when printing images Read write mode The card slot is used as the memory card drive of the computer Image data can be written into the ti AE TTEN S an memory card Se TEE EE TEONE 3 Click Next When you have selected Read write mode read Carcel the precaution and click Next
26. e from the Menu 1 Press the Menu button The menu listing is displayed amp Print all i Specify images E Print index Select layout DPOF Tt Maintenance OK Select Start printing 2 Use the A W buttons to select Print all and then press the OK button The print confirmation screen is displayed 1 Confirm the print settings To change any of the settings press the Settings button See Specifying the Paper and Optimizing Images on page 22 3 Press the Print amp Print all Current settings 101 6x152 4mm Photo Paper Pro Borderless YYYY MM DD Settings Change Print Print button TD 2 Use the amp W buttons to specify the number of copies to print All images saved on the memory card will be printed 17 Printing an Image List Print Index You can print a list of all images saved in the memory card known as an index print 1 Prepare to print 1 Turn on the printer and load the paper See Loading Paper on page 11 2 Insert the memory card into the card slot See Inserting a Memory Card on page 6 A stored image is displayed on the LCD 2 Select the print mode from the Menu 1 Press the Menu button The menu listing is displayed pila Ean E Print index 2 Use the A V buttons to select Print index A at input and then press the OK button 4T Maintenance The print confirmation screen is displaye
27. er of sheets up to 10 sheets one at a time to avoid sheets sticking together 13 Printing Images from a Memory Card The following functions are available when printing from a memory card Specifying how many copies to print for each image on page 14 Printing all images on page 17 Printing an Image List Print Index on page 18 Specifying the layout on page 19 Printing According to the Settings Made on the Camera DPOF Printing on page 20 Specifying the Paper and Optimizing Images on page 22 Specifying how many copies to print for each image You can specify how many copies to print for each image In addition you can trim each image before it is printed E Specifying the number of copies to print for each image 1 Prepare to print 1 Turn on the printer and load the paper See Loading Paper on page 11 2 Install the memory card into the card slot See Inserting a Memory Card on page 6 A stored image is displayed on the LCD 2 Select the print mode from the Menu 1 Press the Menu button The menu listing is displayed Speci imagen 4 _ 2 Use the A YW buttons to select Specify A a images and then press the OK button yout ae DPOF The screen for specifying the number of Bld images is displayed 14 3 Specify the number of copies to print 1 Using the lt p buttons select the image you wish to print 11002 023 100 00
28. ess the Resume button on the printer Paper Jam Remove the jammed paper load new media and press the Resume button Printer cover open Close the front cover No print head The Power lamp on the printer flashes five times No print head is installed Install a print head according to the Quick Start Guide When there is a print head installed the print head is defective Contact a Canon service representative Waste tank full The waste ink tank is nearly full Press the Resume button on the printer to recover from the error Contact a Canon service representative as soon as possible Printer error An error requiring servicing has occurred The Power lamp on the printer flashes alternately orange and green Turn off the printer unplug the power cord from the power supply plug the power cord back in and then turn on the printer If the same error occurs contact a Canon service representative 45 An Error Message is Displayed While Using the Photo Viewer If one of the following messages appears while using the Photo Viewer printing may be disabled or the Photo Viewer may be terminated forcibly Error Massage Try This Executing maintenance Printing cannot be done in the maintenance mode Insert a memory card Insert a memory card after checking its orientation See Using a Memory Card on page 6 If a memory card has already been inserted remove it and then insert it again Next check t
29. gle display mode or in the index display mode Specified numbers of images or an index print using the DPOF function Images other than Exif may not be index printed The images taken with an Exif 2 2 compatible digital camera will be adjusted by using the Photo Optimizer PRO function If date printing is set on the digital camera the date of shooting will be printed excluding the index print Images will be scaled automatically according to the size of the media set on the digital camera The digital camera does not support the following functions Print quality setting Maintenance The print head cannot be aligned through the digital camera To align the print head use the operation panel of the printer To disconnect the cable connected between the digital camera and printer follow the procedure below 1 Disconnect the cable from the printer 2 Turn off the digital camera 3 Disconnect the cable from the digital camera When disconnecting the cable be sure to hold the connector by its sides 26 Other Useful Functions Using Photo Viewer The Photo Viewer application allows you to preview the print image on the display of the computer In addition photos can be printed at high speed through the use of the computer s performance N Important To use the Photo Viewer the printer must be connected to the computer and the printer driver must have been installed in the computer If the printer driver has not bee
30. h the printed surface until the ink dries For specific drying times refer to the instructions packaged with your media 12 E Media Types for Card Direct Printing You can use the following Canon media Setting Paper size Paper Size 1 101 6x152 4mm 127x177 8mm M Settings Check Setting Paper Type Paper Type 2 Photo Paper Pro Photo Paper Plus Glossy Plain paper Settings Check For instructions on how to display and set these settings see Specifying the Paper and Optimizing Images on page 22 Media Type Paper Rest Load Limit Paper Size Paper Type Plain Paper A4 Letter Up to 150 A4 8 5 x 11 Plain Paper sheets Photo Paper Pro A4 Letter 10 sheets 1 A4 8 5 x 11 101 6 x 152 4 mm 4 x 6 up to 20 sheets 101 6 x 152 4 mm 14 x 6 Photo Paper Pro Photo Paper Plus Glossy A4 Letter 10 sheets 1 A4 8 5 x 11 101 6 x 152 4 mm 4 x 6 up to 20 sheets 101 6 x 152 4 mm j4 x 6 127 x 177 8 mm 5 x 7 up to 20 sheets 127 x 177 8 mm 5 x 7 Photo Paper Plus Glossy Notes When using plain paper 64 gsm or Ib up to 150 sheets can be set For the number of sheets loadable at a time on the Photo Paper Tray refer to the electronic User s Guide 1 When loading A4 Letter size paper in the sheet feeder do not load the paper all at once Place the necessary numb
31. hange the settings If there are no settings to change proceed to Step 7 3 Press the OK button or the p button Paper Size 1 101 6x152 4mm 127x177 8mm M Settings Check 1 Press the Settings button The Paper Size tab is displayed 2 Press the A W buttons and select the paper size to set After the paper size is set the Paper Type tab is displayed For more information about each setting see Specifying the Paper and Optimizing Images on page 22 4 When you ha Paper Type 2 Photo Paper Pro Photo Paper Plus Glossy Plain paper Settings Check 101 6 x 152 4mm Photo Paper Pro Borderless YYYY MM DD High quality Exif Print Noise reduction off OK Set 5 Confirm the settings and press the OK button The print confirmation screen is displayed 7 Start printing 10 Gal Print an image Current settings 101 6x152 4mm Photo Paper Pro Borderless YYYY MM DD Settings Change Print Print GT oe sk GS ve completed the selection press the Settings button The Setting confirmation is displayed i tings OK y 1 Press the A W buttons to specify the number of copies to print 2 Press the Print button The specified number of copies of the selected image will be printed Loading Paper This section describes how to load the paper and select the paper sizes and type
32. hat the Indicator lamp stays on The printer s card slot has been write enabled The memory card utility started on the computer has write enabled the card slot When the card slot is write enabled the printer cannot print images When you have finished writing data to the card cancel the write enable mode For the cancellation procedure see Setting up the Card Slot as the Memory Card Drive of the Computer on page 29 There is a problem with the memory card or it is not inserted The memory card is inserted incorrectly Insert the memory card after checking its orientation See Using a Memory Card on page 6 If a memory card has already been inserted remove it and then insert it again Next check that the Indicator lamp stays on The memory card cannot be read Image data edited processed on the computer must also be printed from the computer Insufficient disk space The hard disk of the computer does not have a sufficient free space Delete unnecessary files on the hard disk to create a sufficient free space then start the Photo Viewer again Insufficient memory The computer does not have sufficient free memory Close some applications or increase virtual memory then start the Photo Viewer again A digital camera is connected to the printer Printing from a computer or the operation panel cannot be done when a digital camera or digital video camcorder i
33. have finished writing data to the card select the read only mode For the cancellation procedure see Setting up the Card Slot as the Memory Card Drive of the Computer on page 29 Failed to align print head Press the Resume button and follow the procedure below 1 Open the front cover and check if there is ink left If there is no ink left replace the ink tanks See Replacing Ink Tanks on page 35 2 Print the nozzle check pattern to verify that the print nozzles are clean See Printing the Nozzle Check Pattern on page 38 3 Move the printer so that the paper output is not in direct sunlight and try automatic print head aligning again 4 If the error persists adjust the print head manually Cannot communicate with Disconnect the camera connection cable press the Resume button digital camera and then connect the cable once more The digital camera should be turned on automatically If not turn it on manually 42 Message Try This Unsupported device Disconnect the camera connection cable press the Resume button connected and then connect the cable once more If the error is still unresolved there is a possibility that you are using a digital camera or digital video camcorder that is not supported by this printer Connect only digital cameras or digital video camcorders that are compatible with this printer Photo Paper Tray is When paper feeding is set to be done from the Photo
34. k for uneven ink output clogged or misaligned When a specific color is missing from the nozzle check pattern clean the print head e Ifink supply is uneven See Print Head Cleaning on page 39 If straight lines are misallign See Aligning Print Head Auto head align on page 41 Media not loaded print Check that your paper is loaded with the correct print side facing up side up Note Follow the instructions packaged with your specialty media for loading and handling E Printed Surface is Scratched Possible Cause Inappropriate Paper Type Check to see if the paper you are printing on is too thick or curled is used See Print Media to Avoid on page 11 Note that smudging may occur at the top and bottom edges of the paper when using Borderless Printing Ensure that the paper you are using is compatible with Borderless Printing Note If the printed surface is still scratched Follow the procedure below and set the Thick paper to Thick paper This procedure also applies to direct printing from your camera 1 Press the Menu button 2 Use the A W buttons to select Maintenance and then press the OK button Thick paper 3 Use the A W buttons to select Thick paper from the Maintenance menu and then press the OK button a 4 Use the A W buttons to select Thick paper and then press the OK button After printing is completed return the Thick paper to Auto 44
35. mages directly without using a computer Use the USB cable that came with your digital camera to connect to the printer Notes e Use only a PictBridge or Canon Bubble Jet Direct compatible digital camera or digital video camcorder for printing directly e This section describes how to operate a Canon Bubble Jet Direct compatible camera For instructions on operating a PictBridge compliant camera refer to Direct Printing for PictBridge compliant Digital Camera e When you print directly from a digital camera you need to operate the printer from the camera itself e You are recommended to use mains power rather than the battery pack to power the camera when it is connected to a printer If you do use a battery pack ensure that it is fully charged Media Types for Digital Camera When you print from a digital camera you can use the following media Digital Camera Setting Media Type Card 1 Photo Paper Pro 4 x 6 101 6 x 152 4 mm Card 2 Photo Paper Plus Glossy 4 x 6 101 6 x 152 4 mm Card 3 Photo Paper Plus Glossy 5 x 7 127 x 177 8 mm LTR Photo Paper Pro or Photo Paper Plus Glossy Letter size A4 Photo Paper Pro or Photo Paper Plus Glossy A4 size 24 Printing from a Digital Camera 1 Ensure that the printer is turned on 2 Load the paper Load the paper as shown below 3 Press the paper guide and slide it against the left side of the media 3 Connect the digital camera and the printer
36. moved do not touch the open ink port 35 4 Install the ink tank 1 Insert the ink tank in the print head holder 2 Press on the PUSH mark until the ink tank snaps firmly into place 5 Close the front cover The print head holder moves to the right The ink tank installation process is now complete Notes e To maintain optimal Print Quality use an ink tank within six months of first use e Once an ink tank has been used do not remove it from the printer and leave it out in the open An ink tank left out in the open and then reinstalled in the printer may not function e Color ink consumption may occur even when black and white or grayscale printing is specified Color ink is consumed in the head cleaning and deep cleaning which are necessary to maintain the printer s capabilities 36 Printing Maintenance When Printing Becomes Faint or Colors are Incorrect When printing becomes faint or colors are incorrect even if ink remains in the ink tanks see if the print head nozzles are clogged and clean them first Follow the procedures below and maintain the print head N Important Before maintaining the print head check the following e Open the front cover and make sure whether the ink tank contains ink If it is out of ink replace it See Replacing Ink Tanks on page 35 Ensure that all the orange tape of the ink tank has been peeled off Press PUSH on the ink tank and ensure that the ink ta
37. n installed install it following the procedure described in the Quick Start Guide 1 Ensure that the printer and the computer are turned on 2 Start the Photo Viewer 1 Insert the memory card in the card slot See Using a Memory Card on page 6 ERZO D Settings g N al l R 5 q 2 Press the Photo Viewer button aN o The current information is displayed on the ie Fin SF display of the computer Print Image Displayed on the Display of the Computer EE pria Se lt 3 Make print settings and start printing Use the operation panel to make print settings 1 Make print settings media size and type bordered borderless with without date See Printing Photograph on page 9 The print image on the display changes according to the settings you make 2 Press the Print button to start printing 27 4 Exit the Photo Viewer Notes O A Ss Y 2 e ZBL Q Changing the Display Mode To change the display mode of the Photo Viewer press the F3 key on the keyboard of the computer or click the display selector button on the screen The display selector button Photo Viewer 001 023 100 0001 1 After printing finishes press the Photo Viewer button to exit the Photo Viewer To exit the Photo Viewer before printing finishes cancel printing and then press the Photo Viewer button The display selector
38. ng DPOF settings Image format CIFF Exif JPEG JFIF and Exif Tiff Print type Standard The images for which you specified Standard using the DPOF function are printed Print type Index The images for which you specified Index using the DPOF function are printed according to the index print layout Images to Print Only the images specified using the DPOF function are printed images cannot be specified on the operation panel Copies Images are printed according to the numbers of copies specified using the DPOF function numbers of copies cannot be specified on the operation panel Other functions addition of comments trimming rotation etc are not supported Images are automatically scaled according to the paper size The upper lower left and or right portion s of the image may be missing depending on the size of the paper you use 20 1 Turn on the printer and load the paper See Loading Paper on page 11 2 Set the DPOF mode 1 Insert the memory card containing DPOF information into the card slot See Inserting a Memory Card on page 6 The DPOF print confirmation screen is displayed Do you want to use DPOF settings Yes 2 Use the A W buttons to select Yes and then press the OK button The print confirmation screen is displayed No Notes DPOF Printing can also be started from the Menu 1 With the memory card cont
39. ng requires a lot of ink Continue Yes 4 Use the A W buttons to select Yes and No then press the OK button Execute only if Cleaning has no effect NI Important The process takes one or two minutes to complete so simply wait until the Power lamp stops flashing Note After print head cleaning finishes After print head deep cleaning finishes print the nozzle check pattern to verify that the print head nozzles are clean See Printing the Nozzle Check Pattern on page 38 When one specific color only does not print see Replacing Ink Tanks on page 35 If the problem remains make sure that ink remains in the ink tank turn off the printer s power for at least 24 hours and then perform deep cleaning of the print head again If the problem still remains the print head may be damaged Contact your local Canon service representative 40 Aligning Print Head Auto head align Aligning the print head position allows you to print without shifts in the color registration There are two ways to align the print head automatic or manual First try adjusting the print head automatically If the automatic print head aligning does not work or if you wish you can adjust the print head manually See Adjusting the Print Head Manually on page 43 1 With the printer on load a sheet of A4 paper in the printer 2 Align the print head automatically 1 Press the Menu button
40. nk is installed securely e Increase the Print Quality setting in the printer driver settings Step1 Printing the Nozzle Check Pattern on page 38 If the print quality is poor If white stripes are noticeable Step2 Step2 Print Head Cleaning on page 39 Aligning Print Head Auto head align on page 41 If the problem remains D i Step3 Print Head Deep Cleaning on page 40 Note If print head maintenance does not resolve the problem contact the Canon service representative 37 Printing the Nozzle Check Pattern Print the nozzle check pattern to determine whether the ink ejects properly from the print head nozzles and to verify print head alignment Use this function when printed results are blurred or the color is incorrect 1 With the printer on load a sheet of A4 paper in the printer 2 Printing the nozzle check pattern 1 Press the Menu button C 2 Use the A W buttons to select Ge Specify images Maintenance and then press the OK button E Print ind A i i a ll ets The maintenance menu is displayed DPOF GT Maintenance OK Select Maintenance r Nozzle check m 3 Use the A W buttons to select Nozzle Esc check and then press the OK button Auto heed aign The pattern print confirmation screen is Mi d alli i THEE a E displayed Contrast E Do you want to print the nozzle check pattern Yes c 4 Use the A W buttons to select Yes an
41. pattern print properly is displayed on the No Use the A W buttons to select Yes and then press the OK button Load plain paper Enter the numbers of 7 Examine the printed pattern and enter the number of column A with fewest white stripes fewest white stripes using the lt p buttons aap y 8 Press the OK button Bees 9 Use the W button and move the cursor to column B D 2 10 Repeat Steps 6 through 8 and enter the pattern numbers up to column G 11 After entering the pattern numbers up to column G press the OK button If the Same Error Persists If the same error persists after a countermeasure is taken according to the above error number turn off the printer remove the power cord plug from the outlet plug the power cord back in and then turn on the printer again 43 E Ink does not come out Printing is Blurred Colors are Wrong White Streaks Possible Cause Try This Ink tank is not seated Check that the ink tanks are firmly seated in the print head and reseat properly Ink tank is empty them if necessary Check to see if all the orange tape has been removed as shown in 1 If a part of the orange tape remains as shown in 2 remove it If ink tank is empty See Replacing an Ink Tank on page 34 Incorrect paper type On the operation panel confirm that the Media Type selected matches the paper loaded Print head nozzles Print the nozzle check pattern to chec
42. pecifying the layout on page 19 Trimming 2 Press the Trimming button The printer is now in Trimming Mode 15 2 Trimming and Rotating the Sections you wish to Print Rotate the trimming area Using the Trimming button you can rotate the trimming area Move the area for trimming Using the lt gt A V buttons you can move the trimming area __Enlarge Reduce the area for trimming Using the Q Q buttons you can enlarge or reduce the trimming area Trimming Rotate A f Trimming gt Button gt OK Set OK Set 3 Finalize the trimmed area 1 Press the OK button The trimming area is finalized and the screen returns to the state when the Trimming button was pushed Sn Trimming Bi as This mark indicates that Trimming is set Notes Once the trimmed area is finalized if you press the Trimming button again you can modify the trimmed area If you want to cancel the Trimming setting press the Trimming button and then the Cancel button in the Trimming screen 16 Printing all images You can print all images saved on a memory card 1 Prepare to print 1 Turn on the printer and load the paper See Loading Paper on page 11 2 Insert the memory card into the card slot See Inserting a Memory Card on page 6 A stored image is displayed on the LCD Select the print mod
43. s connected to the printer After completion of operation from the digital camera disconnect the connection cable Failed to communicate with the printer The computer cannot communicate with the printer Check whether the cable is connected securely between the printer and computer Turn the printer off and on again then start the Photo Viewer again Failed to print An unexpected error occurred during printing Turn the printer off and on again An internal error code nnnn occurred n Alphanumeric character An internal error occurred Turn the printer off and on again then start the Photo Viewer again If the same error persists reboot the computer and then start the Photo Viewer again 46 The following ink tanks are compatible with this printer For details on ink tank replacement refer to Print Head Maintenance in this guide 6 6 6 6 5 BCI 6BK BCI 6C BCI 6M BCI 6Y BCI 6PC BCI 6PM QA7 2791 V01 XX2003XX CANON INC 2003 PRINTED IN THAILAND
44. s from the operation panel E Print Media to Avoid Do not use the following types of paper Using such paper will not only produce unsatisfactory results but can also cause the printer to jam or malfunction Folded curled or wrinkled paper Damp paper Excessively thin paper less than 64 gsm or 17 Ib Excessively thick paper more than 105 gsm or 28 Ib non Canon branded paper Picture postcards Postcards affixed with photos or stickers Any type of paper with holes such as loose leaf E Loading the Print Media In this example description is provided using Photo Paper Plus Glossy 4 x 6 101 6 x 152 4 mm in your printer Refer to Media Types for Card Direct Printing on page 13 for compatible paper 1 Turn on the printer 2 Flatten the four corners of the paper before loading it Note If paper is curled gently bend the corners in the opposite direction until the paper becomes completely flat 11 3 Preparing to Load Paper 1 Open the paper support 2 Open the cover and pull out the paper output tray 4 Loading the Paper Load Limit Mark Do not load beyond this Load Limit Mark 1 Insert the paper in the sheet feeder with print side facing up Load the media with the more glossy surface facing up 2 Align the paper stack snug against the right side of the sheet feeder 3 Press the paper guide and slide it against the left side of the stack of paper Note Do not touc
45. ssing the q button increases contrast Pressing the p button decreases contrast Oki Set e 3 After adjusting contrast at your discretion press the OK button The LCD display will be changed to the adjusted contrast 32 Reducing the Sound of Printer Operation The Quiet Mode allows you to significantly reduce the sound the printer generates during operation It is ideal when working at night or in crowded environments N Important Print speed may be somewhat slower than in the normal operating mode e Sound reduction is not as effective when certain printing options are selected Sound generated during printer warm up is the same as during normal operation The following operations are effective only when you are printing from a memory card or from a digital camera connected to this printer If you are printing with your computer connected specify the required settings in the Printer Driver 1 Turn on the printer 2 Select Maintenance from the Menu 1 Press the Menu button amp Print all Ga Specify images Print index B Select layout DPOF GT Maintenance OK Select 3 Select Quiet mode Head cleaning Deep cleaning Auto head align Manual head align Thick paper Contrast Quiet mode Quiet mode Off 2 Use the A W buttons to select Maintenance and then press the OK button The maintenance menu is displayed
46. the layout is displayed 1 Press the lt p buttons to specify the layout The screen for specifying the image to print is displayed 19 4 Select the image to print 1 Using the lt gt buttons select the image you wish to print 2 Using the A W buttons to specify the number of copies to print For example if you select Borderless x 2 in the Layout and set the number of copies to print to 2 two identical images will be printed on a sheet 3 Repeat steps 1 and 2 for each image you wish to print 4 Press the OK button The print confirmation screen is displayed Note For each image selected you can also set the area to print using the Trimming function See Printing a specified area Trimming on page 15 5 Start printing 1 Confirm the print settings To change any of the settings press the Settings button See Specifying the Paper and Optimizing Images on page 22 Select layout x 1 Current settings 30 101 6 x 152 4mm Photo Paper Pro gt YYYY MM DD Settings Change Print Print 2 Press the Print button The specified number of copies for each image will be printed Printing According to the Settings Made on the Camera DPOF Printing If DPOF Digital Print Order Format settings are made on the camera images are printed automatically according to those settings Notes This printer allows you to make the followi
47. uce the area to be trimmed See Trimming and Rotating the Sections you wish to Print on page 16 14 14 Indicator Lamp The indicator lamp is lit when memory card reading is enabled and flashes while the memory card is being read NI Important Removing the memory card or turning off the printer while the Indicator Lamp is flashing can damage the data stored in the memory card Note To zoom in to an image Follow the procedure below to zoom in to the image displayed on the LCD 001 023 100 0001 4 gt 4 OK Print q Scroll the image with A V lt 4 P buttons Menu Displays Inserting a memory card 10017023 100 0001 4 gt OK Print From the Menu Print all i Specify images E Print index B Select layout DPOF Qf Maintenance OK Select Print all Prints all images See Printing all images on page 17 Specify images Prints the specified number of copies for each image You can also trim each image See Specifying how many copies to print for each image on page 14 Print index Prints an index of all images See Printing an Image List Print Index on page 18 Select layout Prints the specified image in the specified layout Borderless or Bordered x2 x4 x8 postcard album See Specifying the layout on page 19 DPOF Prints according to the DPOF settings if available See Printing A

Canon i900D Printing Guide

Contents

Download Pdf Manuals

Related Search

Related Contents