Balance KH8097 User's Manual
Contents
1. T G gy wae Time Date Display Systolic Blood Pressure Diastolic Blood Pressure Pulse per Minute Start stop measuring process Sequential memory recall Time Date Adjust the setting Select memory block Enter limit values Time Date Select position Confirm entered values Number of saved measured values Battery compartment KH 8097 Blood pressure meter 1 Intended Use 0 eee 4 2 Package contents 0eeeeeeeeee 4 3 Important information for your health and safety 0cccee eee eee 5 4 Insert exchange batteries 7 5 Adjust date time 0cccceeeee eee 8 6 Enter limit values 000eeeeeeee 9 7 Fitting the appliance 05 10 8 Measuring blood pressure 005 12 9 Saving measured values 0 000 14 10 Cleaning and Care 0cceueeeaee 16 11 Storage and Disposal 055 17 12 Troubleshooting 0cceee ee eee 18 13 Technical Data iiss sciicccorecenaeareaens 20 14 Warranty and service 00000es 21 This manual is a product component Please keep it in a safe place for later reference and if the appliance is sold pass it on to the new owner 3 1 Intended Use With the blood pressure meter KH 8097 you can quickly and easily measure your blood pressure save the mea sured values enter in limit values as well as display the progress and average of the la2. in the ordinary household garbage poisonous heavy metals Dispose of these at a battery collection point or at your dealer 12 Troubleshooting Never open the casing you will not be able to close it again correctly without a special tool Do not carry out repairs by yourself In case of problems approach the Customer Service department see Warranty Card f no display appears although a button has been pressed Remove the batteries and insert them again after a few seconds If the sleeve pumps itself up continuously press the button start stop to interrupt it If you cannot stop the inflation process in this way remove the sleeve immediately and take out the batteries Appears as soon as a pul se is detected If it does not appear or unregularly the identification is disrupted Appears when the batte ries are almost completely flat Appears if the measure ment could not be succes sfully completed Measurement being taken What do the symbols on the display mean What is to be done Keep the arm still do not move or speak Replace the batteries as soon as the sym bol appears see Chapter 4 Check the correct positioning of the sleeve Chapter 7 Keep the arm still do not move or talk nothing all ok 13 Technical Data Measurement range Measurement accuracy Inflation deflation Pressure sleeve size Operating temper
3. Fitting the appliance Use the appliance only on persons whose wrist fits the pressure sleeve The sleeve must be attached lightly and closed firmly with the Velcro fastener ar 3 The sleeve is appropriate to a wrist perimeter se of 135m 195mm If the wrist is too thin it may not be possible to pump up the pressure sleeve sufficiently and in this case an exact measurement is not possible the wrist is too thick it may not be possible to fasten the pressure sleeve firmly enough and in this case also it is not possible to obtain an exact measurement A Caution Do not use the appliance if you have any injuries or lesions to the wrist These could be aggrava ted by pressure when the sleeve is pumped up A measurement of blood pressure can only be meaning ful if the blood circulation has settled You should take a seat and relax for 3 5 minutes before taking a measurement Notice Before taking the first measurement remove the protective foil from the display Place the appliance on the inside of the left wrist as illustrated Close the Velcro fastener firmly but only sufficiently to ensure the sleeve is lying evenly 8 Measuring blood pressure 7 g J o JBI It is important to avoid moving the appliance in any way while a measurement is being taken The arm should be supported on a firm surface and held still As far as possible do not talk Position
4. ature Storage temperature Power supply Memory Dimensions Weight 0 300 mmHg Pressure Pulse 40 200 beats minute 3 mmHg Pressure Pulse 5 automatic for wrist circumference 135 195 mm 10 40 C at 30 85 relative humidity 20 C 50 C at 10 95 relative humidity 2 x Batteries 1 5 V Typ AAA for ca 250 Measurements Only Alkali batteries 3 blocks with 30 memory cells each 70 x 72 x 29 mm LxB x H approx 110 g The CE trademark of the measuring appliance fulfills the EC Guideline 93 42 EEC The blood pressure measuring device fulfills the European Regulations EN 1060 Part 1 EN 1060 Part 3 and IEC 60601 1 2 20 14 Warranty and service The warranty conditions and the service address can be found on the warranty card 21
5. d pressure meter contains precision compo nents and electronics Measurement accuracy and the usable life of the appliance both depend on careful handling You must protect the appliance from knocks and from being dropped use the appliance only in normal interior ambient conditions protect it from humidity dirt exposure to excess heat or cold and temperature fluctuations keep it well away from electromagnetic fields such as mobile telephones sound amplification systems or switched on electrical appliances Do not inflate the pressure sleeve if the appliance has not been fitted if the sleeve is twisted A Important Do not press the button START STOP unless the appli ance has been fitted Otherwise inflation of the pressu re sleeve might be set off inadvertently Replace the batteries when the appliance functions become faint at the latest after 1 year In this way you will prevent discharged batteries from leaking into the appliance Open the battery compartment as illustrated e Insert the batteries exactly as marked in the battery compartment Lay the strip underneath the batteries Battery type 1 5 V size AAA A Notice Empty batteries must not be disposed of in the ordinary household garbage poisonous heavy metals Dispose of them at a collection point for old batteries or with your dealer Y 5 Adjust date time This is necessary should you wish to save and eva l
6. of measurement for each is indicated c Erasing stored measurements When all memory spaces are occupied the appliance automatically overwrites the oldest measurement Should you however wish to erase all measured values select first of all your memory block For this repeatedly press the button CSET until your memory block no 1 to no 3 appears in the display Press the button MEM to call up the indicated memory block Now press the buttons SET Jand at the same time 47 appears in the display All measured values in your memory block are now erased 10 Cleaning and Care e Carefully clean the equipment and pressure sleeve using a slightly damp cloth only e Do not use chemical agents or solvents for cleaning e Do not under any circumstances immerse the appliance in water as fluids will penetrate through to the inside This would cause irreparable damage to the appliance 11 Storage and Disposal Should you not use the appliance for a longer period of time remove the batteries to prevent possible damage by battery leakage Keep the appliance only in the box supplied Store it at a location that is both dry and protected from large temperature variations Do not dispose of the appliance in your nor mal domestic waste If you wish to dispose of mam the appliance at a later time take it to a recycling centre for electronic equipment Notice Empty batteries must not be disposed of
7. st 3 measurements The appliance is intended for checking your own blood pressure people over 18 years of age private use in the home The appliance is not intended for measuring the blood pressure of children for usage in professional or commercial care 2 Package contents Blood pressure meter Storage box 2 Batteries 1 5 V Typ AAA Operating manual Warranty card 3 Important information for your health and safety The information contained in this handbook and that obtained from measurements with the appliance should not encourage you to make any forms of diagnosis to treat health problems or to make any decisions about medications The measurements taken by yourself can only be used for your information they cannot be a substitute for examination by a doctor Blood pressure is heavily influenced by time of day physical exertion and other factors Do not rely on individual measurements Diseases of the cardio vascular system can result in erroneous measurements as can very low blood pressure circulatory disorder arrhythmia and other pre existing conditions for example diabetes mellitus Especially in such cases you should not rely on the measurement values determined by yourself Under no circumstances should you abstain from having your blood pressure measured by a doctor in cases of known ailment although the values shown by this appliance are without defect This bloo
8. the arm such that the appliance is at the same level as the heart This is roughly a hand s breadth above the bottom of the rib cage Now press the button START STOP Press the button SET to programme the desired memory block no 1 to no 3 Press the button again All elements in the display appear shortly then the desired memory block The measurement process starts with the pumping up of the sleeve To break off the measurement process press the button again During measurement air is gradually released from the sleeve If the measurement fails at this point the appli ance may pump some more air into the sleeve If a measurement is taken successfully the remaining air is released and the display shows the systolic blood pressure at the top in healthy adults it lies between about 105 140 mmHg the diastolic blood pressure in the middle in healthy adults it lies between about 60 90 mmHg the pulse measurement at the bottom The m easured blood pressure as well as the program med limit values are displayed alternatively Should a limit value be exceeded SYS or DIA the appropriate value flashes in the display Press the button to change over to the Start display and possibly alter the programmed values The appliance is equipped with an automatic switch off Should a button not be activated within one minute the appliance switches itself off Press
9. the button to switch the appliance back on 13 9 Saving measured valas ie ib DIA The appliance has three memory blocks numbered 1 to 3 each with 30 memory locations It can therefore save up to 30 measurements for 3 persons or up to 90 mea surements for one person Additionally the average of the last three measurements can also be displayed a How to save a measurement First of all select your memory block For this repeatedly press the button SET until your memory block no 1 to no 3 appears in the display When you now carry out the measurement process as detailed in chapters 5 amp 8 the results are saved into the selected memory block b Recalling a previous measurement First of all select your memory block For this re peatedly press the button CSET until your memory block no 1 to no 3 appears in the display Press the button MEM to call up the indicated memory block There then appears on the lower dis play line an A average and in alternating display the average values of the last three measurements as well as the programmed limit values for the appropriate individual are shown Press the button MEM again In the lower display screen the number of saved measurement values for the individual memory block are shown Pressing again on the button MEM allows you to browse through all saved measurement results The date and time
10. uate your measurements Press the button MODE The month and day as well as the time appear at the top of the display You can move from one position to the next by pressing the button again The currently selected position flashes Press the button Ser to change the value of the flashing position In the time display the second part of the day is indicated by a small letter P for PM under the colon character Then press the button to save the program med details and change over to programming the systolic and diastolic value limits 6 Enter limit values After you have entered in the time and date the first programmable limit value for systolic blood pressure blinks in the display Press the button to raise the value in 5 mmHg steps The adjustment range for systolic blood pressure lies between 70 250 mmHg Press the button MODE to save this setting and move to programming the diastolic limit values Press the button to raise the value in 5 mmHg steps The adjusment range for diastolic blood pressure lies between 40 245 mmHg Press the button MODE to save the setting Repeat the last five instructions to enter the value limits for further users 2 3 Press the button START STOP to discontinue the programming of limit values The programming of limit values into each of the 3 memory slots no 1 to no 3 can also be carried out at a later time 7
Download Pdf Manuals
Related Search