Audiovox VX7012 Installation Manual
Contents
1. JENSEN VX7012 VX4012 INSTALLATION GUIDE Made for iPod Q iPhone External Microphone Mounting Sleeve amp Removal Keys e Installation Guide What s in the Box Tools and Supplies The following items are supplied The following tools and supplies are needed to with the VX7012 VX4012 install the head unit e Head Unit e Torx type flat head and Philips e GPS Antenna VX7012 Only screwdrivers e Trim Ring e Wire cutters and strippers e Hardware Bag e Tools to remove existing radio screw e Power Speaker Output Harness driver socket wrench set or other e Remote Control tools e Electrical tape e Crimping tool e Volt meter test light e Crimp connections e 18 gauge wire for power connections e 16 18 gauge speaker wire Optional Equipment Steering Wheel Control Interface SWC The VX7012 VX4012 are compatible with various PAC Metra and iDatalink Maestro SW steering wheel control adapters Disconnect the Battery To prevent a short circuit be sure to turn off the ignition and remove the negative battery cable prior to installation NOTE If the head unit is to be installed in a car equipped with an on board drive or navigation computer do not disconnect the battery cable If the cable is disconnected the computer memory may be lost Under these conditions use extra caution during installation to avoid causing a short circuit Replacing the Fuse When replacing the vehicles radio fuse always2. ANTENNA VX7012 Only IGNITION SWITCH ED RED N FRONT L aE BATTERY tik 3 YELLOW VIDEO OUT White Purple White Purple _ SWCB White Brown White Brown PINK PARKING BRAKE L___ E RED C WHITE S SE YELLOW REAR R FRONT R BATTERY YELLOW IGN ACC RED FRONT R GRAY REAR R VIOLET FRONT R GRAY BLACK VIOLET BLACK SSS PLY 7 REAR L GREEN j T EEn FRONT L WHITE BLACK REAR L GREEN BLACK ORANGE TFT DIMMER REAR R MONITOR SWC ADAPTER CABLE SWC GND Brown Black Brown Black n BACKUP YELLOW RCA REAR CAMERA CAMERA m ew Voxx Electronics Corporation Hauppauge NY 11788 Technical Assistance 800 323 4815 www jensenmobile com 2015 Printed in China
3. shboard or center console using the reverse procedure in step 1 above CAUTION Be careful not to damage the car wiring Trim plate NOTE It is the end users responsibility to install and operate this unit in a manner in accordance with local state and federal laws The PARKING BRAKE wire MUST BE CONNECTED as directed in the manual Using the Cosmetic Trim Ring A cosmetic trim ring is supplied with the head unit for installation flexibility This unit will fit into most import dashes with little or no modification to the dash board cavity Some US domestic vehicle dashes will accept a Single DIN chassis but there is usually a small gap between the radio and dash piece after installation is complete In this case use the trim ring to conceal any gaps that may be present NOTE For proper operation of the CD DVD player the chassis must be mounted within 30 of horizontal Make sure the unit is mounted within this limitation N Wiring Diagram CAUTION IMPORTANT Incorrect wiring connections can damage the unit Follow the wiring instructions carefully or have the installation handled by an experienced technician Need Help For technical assistance call the Jensen customer support line at 1 800 323 4815 paPUSUWIUOAL s UOI L JESU EUOISSAJOg SUOI IUNY DMS Ije WOddns you Aew sapiyan awos BLACK 3 5MM BT MICROPHONE l AUTO ANTENNA BLACK ANTENNA O o I WH BLACK 1MM WIRE BT ANTENNA GPS
4. use the proper rated replacement fuse Using a fuse with an improper rating could damage the unit and cause a fire ISO DIN Installation The head unit is designed to fit into a 1 0 DIN dashboard opening The unit has threaded holes in the chassis side panels which may be used with the original factory We Felt of some Toyota Nissan Mitsubishi Isuzu Hyundai and Honda vehicles to mount the radio to the dashboard Please consult with your local car stereo specialty shop for assistance on this type of installation 1 Remove the existing factory radio from the dashboard or center console mounting Save all hardware and brackets as ac Bests they will be used to mount the new radio _ S 2 Remove the factory mounting brackets and hardware from the existing radio and attach them to the new radio CAUTION Do not exceed M5 X 6MM screw size Longer screws may damage components inside the chassis 3 Place the radio in front of the dashboard opening so the wiring can be brought through the mounting sleeve Follow the wiring diagram carefully and make certain all connections are secure and insulated with wire nuts or electrical tape After completing the wiring connections plug the connector into the mating socket on the rear of the chassis Turn the unit on to confirm operation vehicle ignition switch must be ON If 9 the unit does not operate re check all wiring until the problem is corrected 4 Mount the new radio assembly to the da
Download Pdf Manuals
Related Search