Audiovox APS-775 User's Manual
Contents
1. Model APS 775 Owner s Manual 3 Button Remote Start Security System With Plug In Shock Sensor amp Starter Disable FEATURES 2 Three Button Programmable RF Transmitters Three Channel Code Learning Receiver Anti Code Grabbing Technology Remote Panic In All Modes Protected Valet Override Remote Start Safety Control Switch Safe Start RF Control Double Push Of RF Transmitter Selectable Automatic Timed Start Mode 7 Function LED Arming Armed Disarmed Valet Zones 1 2 amp 3 Intrusion Alert With Memory Audible Arm Disarm Defect Zone And Intrusion Indications Instant Siren Activation All Entry Points Starter Disable When Armed True Last Door Arming Defective Zone By Pass On Command RF Chirp Delete Mini Six Tone Siren Two Stage Shock Sensor Selectable Run Time 10 or 15 Minutes OPTIONS Remote Trunk Release Remote Keyless Entry Illuminated entry Remote Power Window Control Remote Garage Door Interface Multiple Vehicle Capable CAUTION Be certain that the vehicle is outdoors before using this or any remote vehicle starting device A running engine produces dangerous carbon monoxide fumes which can be harmful or fatal if prolonged exposure occurs DO NOT remote start the vehicle if it is garaged Page 1 Your APS 775 Remote Start Alarm System has many features and available options some of which are selected at time of installation For your reference the list on page 7 of this manual shows what fea2. 2 times 2 Shut off the vehicle using the keychain transmitter by pressing and releasing the second channel transmitter button 2 times 3 Within 10 seconds of step 2 activate the RF start command two times Push the second channel button of your keychain transmitter 4 times The parking lights will flash and the siren will chirp 4 times indicating the timed start mode is activated CANCELING THE AUTOMATIC START UP TIMER To cancel the automatic start up timer do one of the following 1 Start the vehicle manually with the use of the ignition key and depress the brake pedal 2 Remote start the vehicle using your keychain RF transmitter Page 6 ADDITIONAL REMOTE FUNCTION CHANNEL 2 The system has an additional feature Channel 2 that can be connected to a number of different optional accessories Some of the more common uses for this channel are Remote Trunk Release Remote Window Close Remote Garage Door Interface To operate the accessory associated with channel 2 press and hold the channel 2 button s of your keychain transmitter for four seconds NOTE The feature that has been added to channel 2 will always be operated using the same transmitter button that controls the remote start unit There is no way to move the channel 2 function to a different channel ADDITIONAL REMOTE FUNCTION CHANNEL 3 The system has an additional feature Channel 3 that can be connected to a number of different optional accessories Some of th
3. and if the optional interior illumination circuit was installed the interior light will flash To disengage the panic feature press and release the arm disarm button If you do not shut off the panic feature the system will time out and shut off automatically after 30 seconds During this mode all normal transmitter functions are operational SAFETY Red Handled CONTROL SWITCH The control switch allows you to temporarily disable the remote starting function of your APS 775 To disable the unit move the red handled control switch to the off position The control switch also allows you to select between 2 hour start up and 4 hour start up when using the automatic start up timer mode The factory preset start up time for this mode is every 4 hours To select between 2 or 4 hour start up timer 1 Begin with the control switch in the on position 2 Turn the ignition switch on then off 3 Within 10 seconds move the control switch off on off on 2 switch cycles to select a 2 hour start timer After 10 seconds expire the parking lights will flash and the siren will chirp 2 times confirming that the two hour start cycle is set Or within 10 seconds move the control switch off on off on off on off on 4 switch cycles to select a 4 hour start timer The parking lights will flash and the siren will chirp 4 times confirming that the 4 hour start timer is set REMOTE STARTING THE VEHICLE The APS 775 WILL NOT start the vehicle if any one of t
4. intrusion attempt was made to the vehicle doors Check all doors for indications of forced entry Note The LED intrusion warning indications are stored in the system s memory and will be erased when the ignition switch is turned on VALET SYSTEM OVERRIDE SWITCH The valet switch allows you to temporarily by pass all alarm functions eliminating the need to hand your keychain transmitter to parking attendants or garage mechanics When the system is in the valet mode all alarm functions are by passed however the remote panic feature and the optional remote door lock unlock will remain operational To enter the valet mode 1 Start with the valet switch in the off position 2 Turn the ignition switch to the on position 3 Within 10 seconds of step 2 move the valet switch to the on position The dash mounted LED will turn on solid indicating that the valet mode has successfully been entered To return to the normal alarm mode operation move the valet switch to the off position any time the ignition switch is in the on position Note In the event that you lose your keychain transmitter or the transmitter fails to operate the alarm system the valet switch can be used to disarm the alarm To disarm the alarm 1 Open the door with the vehicle door key The siren will sound 2 Turn the ignition switch to the on position 3 Move the valet override switch to the on position The system will disarm and the vehicle can be opera
5. 3 CHIRPS ARMING WITH ENTRY POINT OPENED 4 CHIRPS DISARM AFTER INTRUSION CONTINUOUS TRIGGERED PANIC ALARM PARKING LAMP INDICATIONS 1 FLASH ARM 2 FLASH DISARM 3 FLASH DISARM AFTER INTRUSION CONTINUOUS FLASH TRIGGERED PANIC REMOTE START SIREN INDICATIONS 1 LONG 1SHORT RF START COMMAND ISSUED IF SELECTED ON REMOTE START PARKING LAMP INDICATIONS 1 FLASH RF START COMMAND ISSUED ON RUNNING UNDER REMOTE START CONTROL IF SELECTED CONTINUOUS FLASH RUNNING UNDER REMOTE START CONTROL IF SELECTED 1998 Audiovox Corp Hauppauge N Y 11788 Form No 128 5321 Page 8
6. d LED will turn off If you have the optional door lock unlock circuit installed the doors will unlock If you have the optional entry illumination circuit installed the interior light will turn on for 30 seconds or until the ignition key is switched on Note If the passive arming mode was selected at time of installation the dash mounted LED will start flashing rapidly indicating that the system is rearming Opening any door will suspend the automatic arming If the parking lights flashed three times and the siren chirps four times this indicates that the alarm system was triggered during your absence Before turning on the ignition key examine the dash mounted LED s flash pattern The number of flashes identifies the triggered zone For additional information refer to INTRUSION WARNING SIGNALS found later in this manual If the siren did not sound upon disarm then the chirps have been turned off Refer to the section titled ELIMINATING THEARM DISARM CHIRPS SILENT DISARMING 1 As you approach the vehicle press and hold the Arm Disarm button of your key chain transmitter for two seconds The parking lights will flash twice and the dash mounted LED will turn off confirming that the system is disarmed The siren will not chirp If you have the optional door lock unlock circuit installed the doors will unlock If you have the optional entry illumination circuit installed the interior light will turn on for 30 seconds or until t
7. e more common uses for this channel are Remote Trunk Release Remote Window Close Remote Garage Door Interface To operate the accessory associated with channel 3 press and release the channel 3 button s of your keychain transmitter Note The channel 3 output will remain active for as long as the transmitter button s are held Certain accessories may take advantage of the extended output capability of this channel Check with your installation center for operation of the accessory that may be connected to channel 3 FEATURE AND FUNCTION SETTINGS To Be Completed By Installing Technician Settings Remote Start Function O 1 Sec O 3 5 Sec 1 Sec L Dbl UL Door Lock Time O Pulse O Steady Run Time O 10 Min O 15 Min Remote Activation Chirp O On O Off Transmitter Button s Remote Alarm Function Arm Disarm C Channel 1 O N A m 02 03 04 Auto Door Lock O On O off Auto Door Unlock O On O off Passive Lock I On O off Passive Arm I On oO Off Remote Trunk Release OJ Channel 2 OChanneel3 01 02 03 4 Remote Window Close O Channel 2 O Channel3 M 02 03 04 Remote Garage Interface Channel 2 O Channel3 1 02 08 04 Page 7 APS 775 SYSTEM FUNCTIONS AT A GLANCE ALARM DASH LED INDICATORS RAPID FLASHING PASSIVE ARMING SLOW FLASHING ARMED OFF DISARMED ON SOLID VALET MODE 3 FLASH PAUSE INTRUSION ZONE 3 2 FLASH PAUSE INTRUSION ZONE 2 1 FLASH PAUSE INTRUSION ZONE 1 ALARM SIREN CHIRP INDICATION 1 CHIRP ARM 2 CHIRPS DISARMED
8. ed entry point hood trunk or doors will cause the alarm to trigger immediately The siren will sound and the parking lights will flash for 30 seconds then stop and continue to monitor all protected entry points If the thief left the door opened the unit Page 2 will sound for six 30 second cycles then shut down isolate the triggered zone and continue to protect all other zones Whenever the system is armed the dash mounted LED will slowly flash This serves as a visual deterrent to a potential thief This LED is a very low current light emitting diode and will not cause the battery to drain even if left unattended for long periods of time Whenever the system is triggered the vehicle s parking lights will flash for the full siren sounding period Optional whenever the system is triggered the interior courtesy light will flash for the full siren sounding period Whenever the system is armed the vehicle starter circuit is disabled and the vehicle will not start with the ignition key Whenever the system is armed any strong impact to the vehicle will cause the shock detector to trigger the alarm Any lesser impact will cause the pre detect stage of the shock sensor to emit a few short series of warning tones from the siren DISARMING THE SYSTEM As you approach the vehicle press and release the Arm Disarm button on the keychain transmitter The parking lights will flash two times the siren will chirp twice and the dash mounte
9. he following conditions exists 1 The Vehicle Hood Is Opened 2 The Gear Selector Is In Any Gear Other Then Park 3 The Brake Is Depressed 4 The Safety Control Switch Is In The Off Position CAUTION Be certain that the vehicle is outdoors before using this or any remote vehicle starting device A running engine produces dangerous carbon monoxide fumes which can be harmful or fatal if prolonged exposure occurs DO NOT remote start the vehicle if it is garaged To Remote Start The Vehicle Press and release channel 2 of your keychain transmitter two times within 2 seconds The vehicle will start and remain running for the pre programmed 10 or 15 minutes As a visual indication the parking lights will flash or turn on depending on the programming set up by your installation center When you arrive at your vehicle disarm the alarm system by pressing and releasing the Page 5 arm disarm button of your keychain transmitter Enter the vehicle and turn the ignition key to the on position CAUTION Do not turn the key to the start position This will cause the starter motor to engage with the already running engine which could result in damage Step on the brake pedal to disengage the remote start unit The vehicle will continue to run but now on it s own power NOTE The engine will stop running before the expiration of the pre programmed run timer if you complete any of the following 1 Press and release channel 2 of your keychain tran
10. he ignition key is switched on Note If the passive arming mode was selected at time of installation the dash mounted LED will start flashing rapidly indicating that the system is rearming Opening any door will suspend the automatic arming If the parking lights flashed three times and the siren chirps four times this indicates that the alarm system had been triggered in your absence Before turning on the ignition key examine the dash mounted LED s flash pattern The number of flashes identifies the triggered zone For additional information refer to INTRUSION WARNING SIGNALS found later in this manual Page 3 INTRUSION WARNING SIGNAL This system will inform you if an intrusion attempt has occurred while you were away from the vehicle Upon disarm the siren will chirp 4 times and the parking lights will flash 3 times Enter the vehicle and before turning on the ignition switch observe the LED flash pattern If the LED flashes one time pause one time pause etc then an intrusion attempt was made by impact or a strong vibration that the shock sensor detected Check the vehicle for possible damage to the glass or body panels If the LED flashes two times pause two times pause etc then an intrusion attempt was made to open the hood trunk or by an accessory triggering device Check the vehicle for indications of forced entry to these openings If the LED flashes three times pause three times pause etc then an
11. ps three times then you have left a door hood or trunk ajar Simply closing that opening will provide full protection If your vehicle has delayed interior lighting you may also get three chirps when arming Once the light turns off you will hear one chirp confirming full arming ARMING THE SYSTEM PASSIVE AUTOMATIC If the passive arming feature has been selected 1 Turn the engine off exit the vehicle and close all doors hood and trunk The dash mounted LED will begin to flash rapidly indicating that the 30 second passive arming timer has begun If the LED does not begin to flash rapidly then you have left a door hood or trunk ajar Closing this entry point will allow the arming cycle will begin If any entry point is opened during the 30 second arming cycle arming will be suspended When all entry points are closed the arming cycle will begin again At the end of the 30 seconds the parking lights will flash once the siren will chirp once and the dash mounted LED will begin to flash slowly confirming the system is armed If the siren did not sound when arming then the chirps have been turned off Refer to the section on Eliminating the Arm Disarm Chirps shown later in this manual Passive door locking is a selectable feature If you have the optional door lock unlock circuit installed the doors may or may not lock passively depending upon the setup during installation PROTECTION WHILE THE SYSTEM IS ARMED Opening any protect
12. smitter two times within 2 seconds 2 Depress the brake pedal 3 Open the hood 4 Move the red handled control switch to the off position 5 Race the engine to above 4000 RPM OPERATING ON AUTOMATIC START UP TIMER MODE The APS 775 has the ability to automatically start the vehicle every 2 or 4 hours over a 48 hour period This feature is especially useful in cold climates where the only means to keep the engine and engine fluids warm is to periodically start the engine CAUTION Be certain that the vehicle is outdoors before using this or any remote vehicle starting device Arunning engine produces dangerous carbon monoxide fumes which can be harmful or fatal if prolonged exposure occurs DO NOT remote start the vehicle if it is garaged TO BEGIN THE AUTOMATIC START UP TIMER 1 Turn the ignition key on then off 2 Within 10 seconds activate the RF start command two times Push the second channel button of your keychain transmitter 4 times The parking lights will flash and the siren will chirp 4 times indicating the timed start mode is activated The vehicle on a 2 or 4 hour interval basis will automatically start run for the pre programmed time 10 of 15 minutes and then shut off This will continue for 48 hours NOTE The automatic start up timer can also be initiated from the keychain transmitter To do this 1 Start the vehicle using the keychain transmitter by pressing and releasing the second channel transmitter button
13. ted normally Always remember to move the valet switch to the off position to ensure the vehicle remains protected at all times ELIMINATING THE NORMAL ARM DISARM CHIRPS You can selectively eliminate the normal arm amp disarm chirps by holding the transmitter button slightly longer when arming or disarming This will prevent the siren chirps for one arm or disarm cycle If you find this inconvenient and wish to eliminate these chirps permanently 1 Start with the valet switch in the off position 2 Turn the ignition switch on then off 3 Within 10 seconds of turning off the ignition move the valet switch on off on off on off 4 If the chirps were on before you started the siren will emit 2 short chirps indicating that the chirps are now off If the chirps were off before you started the siren will emit one Page 4 Short chirp indicating that the chirps are now on NOTE If the vehicle battery is disconnected then reconnected the unit will return to the default setting of chirps on Repeat the above procedure to eliminate the arm disarm chirps REMOTE PANIC OPERATION The arm disarm button of your keychain transmitter also serves as a panic switch and will turn the alarm on from the maximum operating range of the transmitter In an emergency situation to use the panic feature press and hold the arm disarm button of your keychain transmitter for 3 seconds This will cause the lights to flash the siren to sound
14. tures and options have beeninstalled Consult your installing dealer for options that may have been installed and are not listed ARMING THE SYSTEM ACTIVE 1 Turn the engine off exit the vehicle and close all doors hood and trunk 2 Press and release the Arm Disarm button of your key chain transmitter one time The parking lights will flash once the siren will chirp once and the dash mounted LED will begin to flash slowly confirming the system is armed If you have the optional door lock unlock circuit installed the doors will lock Note If the siren chirped three times then you have left a door hood or trunk ajar Simply closing that opening will provide full protection If your vehicle has delayed interior lighting you may also get three chirps when arming Once the light turns off you will hear one chirp confirming full arming Ifthe siren did not sound when arming then the chirps have been turned off Refer to the section on Eliminating the Arm Disarm Chirps shown later in this manual SILENT ARMING ACTIVE 1 Turn the engine off exit the vehicle and close all doors hood and trunk 2 Press and hold the Arm Disarm button of your key chain transmitter for two seconds The parking lights will flash once and the dash mounted LED will begin to flash slowly confirming the system is armed The siren will not chirp If you have the optional door lock unlock circuit installed the doors will lock Note If the siren chir
Download Pdf Manuals
Related Search