Atmel AT91CAP7X-DK User's Manual
Contents
1. CAP CUSTOMIZABLE MICROCONTROLLERS 7 as Wi E eg a pcre a wet a use pi M en L i q 11 pi aa ree aoe y Cae ie pet AE d Sas TANA ata z jbp aT loarn e ra a ae Eien a i m i ek i Iona iTA iy i l 11 1 j d n r ENR Ped bo iwi AT91CAP7X DK Development Kit for CAP Customizable Microcontroller The AT91CAP7X DK development board implements the fixed portion of the AT91CAP7 device as a microcontroller standard product tightly coupled to a high density FPGA that emulates the MP Block The boards also include a range of memories and physical interfaces connectors representing external system components This configuration enables parallel hardware software testing of the application under development at close to operational speed with no penalty for hardware modifications This enables software development to proceed in parallel with hardware development and significantly reduces the design cycle time increasing confidence in a right first time system solution The AT91CAP7X DK development board or kit is composed of three ae k ii ANN Mim A Ea associated boards namely Motherboard Mezzanine and Memory fa l i Extension to be used jointly in order to develop AT91CAP7 processor gif applications AT91CAP7X DK Motherboard The AT91CAP7X DK motherboard features the following on board interfaces oe E ATX power supply connector E Image Sensor expansion connector E 2x Full speed Host U2. SB interfaces E 16 push buttons arranged in a keypad form E 100 base TX Ethernet PHY with three status E CAN bus interface LEDs E Software controlled Power LED E DBGU serial communication port E 2x general purpose LEDs E 4x analog inputs E PIO expansion connectors PIOA PIOB PIOC E AC97 interface with three 3 5 mm audio jack PIOD connectors MIC IN LINE IN LINE OUT E CAP Mezzanine extension connectors E 2S audio codec with two 3 5 mm audio jack 2x 320 pins connectors LINE IN LINE OUT E PCI64 form FPGA I O extension connector E 2x SD MMC card slots E Custom mezzanine style FPGA I O extension E Atmel TWI serial EEPROM connector E 1 4 inch TFT LCD VGA interface E 3x USB device PHY interfaces with USB B E Touch Screen Controller connectors FPGA controlled AT91CAP7X DK Development Kit for CAP Customizable Microcontroller AT91CAP7X Features E 160 KB of fast on chip SRAM E A large MP Block of 450K ASIC gates 2 input NAND equivalents E Micro Core ARM7TDMI at 80 MHz E MPRAM 2x DPRAM 2K x 16 E ROM 256 KB E A minimal number of ARM peripherals are instantiated in the fixed portion of the design to address low cost applications E Flexibility to instantiate other peripherals in the MP Block using IP available in Atmel s vast library The CAP Customizable Microcontroller Atmel s CAP is an ARM microcontroller based system on chip with fast local memory a wide range of industry standard peripherals and interfaces an
3. VEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice Atmel does not make any commitment to update the information contained herein Unless specifically provided otherwise Atmel products are not suitable for and shall not be used in automotive applications Atmel s products are not intended authorized or warranted for use as components in applications intended to support or sustain life Headquarters Atmel Corporation 2325 Orchard Parkway San Jose CA 95131 USA TEL 1 408 441 0311 FAX 1 408 487 2600 International Atmel Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong TEL 852 2721 9778 FAX 852 2722 1369 Atmel Europe Le Krebs 8 Rue Jean Pierre Timbaud BP 309 78054 St Quentin en Yvelines Cedex France Tel 33 1 30 60 70 00 Fax 83 1 30 60 71 11 Atmel Japan QF Tonetsu Shinkawa Bldg 1 24 8 Shinkawa Chuo ku Tokyo 104 0033 Japan NEI 1 323523 35511 FAX 81 3 3523 7581 Product Contacts Technical Support www atmel convproducts AT91CAP Sales Contacts www atmel com contacts Web Site www atmel com a Lu aa LLI jae a 2008 Atmel Corporation All rights reserved Atmel logo and combinat
4. d a Metal Programmable MP Block that allows the designer to add custom logic By combining the performance density and low power consumption of the fixed portion of the device with the flexibility of the MP Block CAP enables application specific products to be developed in a fraction of the time and at a fraction of the cost of standard cell ASICs but at a unit price close to that of standard cell devices CAP also offers superior performance smaller form factor and lower power consumption at a unit price significantly lower than an MCU plus FPGA combination for the same functionality Disclaimer The information in this document is provided in connection with Atmel products No license express or implied by estoppel or otherwise to any intellectual property right is granted by this document or in connection with the sale of Atmel products EXCEPT AS SET FORTH IN ATMEL S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL S WEB SITE ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE OR NON INFRINGEMENT IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT INDIRECT CONSEQUENTIAL PUNITIVE SPECIAL OR INCIDENTAL DAMAGES INCLUDING WITHOUT LIMITATION DAMAGES FOR LOSS OF PROFITS BUSINESS INTERRUPTION OR LOSS OF INFORMATION ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT E
5. ions thereof and others are registered trademarks CAP and others are trademarks of Atmel Corporation or its subsidiaries ARM and ARM7TDMI are registered trademarks of ARM Ltd Other terms and product names may be trademarks of others REV 8522A 03 08 AMEL T A
Download Pdf Manuals
Related Search