AT&T E598-2 User's Manual
Contents
1. Press to initiate an inter com conversation or transfer a call Getting started Battery installation amp charging After battery installation the battery may have enough charge to allow for some calls For best performance place the handset in the charger or telephone base and allow it to charge for 16 hours before use You can keep the battery charged by returning the handset to the charger or the telephone base after each use When the battery is fully depleted a recharge takes about 12 hours The average talk time on a fully charged battery is about eight hours depending on environmental conditions and the standby time when idle is approximately five days 1 Plug the small 2 Plug the end of the smaller large end of power adapter into the smaller the jack on the power underside of char adapter into ger then route the an electrical cord through the outlet slot as shown 3 Plug the battery 4 Place the 5 Slide battery securely into the plug battery and compartment inside the handset wires neatly cover towards battery compartment inside the com the center until matching the color partment it clicks closed coded label 1 6 The battery may have enough charge to allow for some calls For best performance Low battery indicator To replace the battery press place handset in Return handset to the in and downward on the tab me arpion telephone base or char to open the battery compart ase or charger er to rech2. SS atat Quick start guide E598 2 5 8 GHz expansion handset for use with AT amp T models E5901 E5902B E5903B E5911 E5912B E5913B E5914B E5921 E5922B E5923B E5924B E6001 E6002B E6012B E6013B E6014B E3813B Getting started j i UP Quick reference guide CENTER Handset LEFT RIGHT DOWN menuzserecrt Press to display the menu Once in the menu press to select an item or save an entry or set ting Press Q or Q to scroll up or down while in menus While entering names or numbers press or Q to move the cur sor to the left or right DIR CID Press to display caller ID information PHONE FLASH Press to make or answer a call During a call press to receive an incoming call if call wait ing is activated Press to display directory entries MUTE DELETE OFF CLEAR While on a call press to mute microphone While reviewing the call log press to delete an indi vidual entry or press and hold to clear the caller ID log While predialing press to delete digits from During a call press to hang up While using menus press to cancel an operation back up to the previous menu or exit the menu display REDIAL PAUSE a string Press to view redial memory While entering numbers press and hold SPEAKER to insert a dialing pause Press to activate hand set speakerphone Press INT again to resume normal handset use
3. arge when a to charge for at ae symbol achas P cover Mik out the lease 16 hours Handset will beep when 2 attery and disconnect before first use battery is low Follow the instructions on this page to install and charge the LOW BATTERY new battery Caution Use only the supplied rechargeable battery or AT amp T replacement battery model 27910 part number 89 0099 00 00 To order visit our website at www telephones att com or call 1 800 222 3111 In Canada dial 1 866 288 4268 Getting started Adding and registering handsets Before using a new E598 2 handset you must register it with your E5901 E5902B E5903B E5911 E5912B E5913B E5914B E5921 E5922B E5923B E5924B E6001 E6002B E6012B E6013B E3813B or E6014B telephone base purchased separately The E5901 E5902B E5903B E5911 E5912B E5913B E5914B E5921 E5922B E5923B E5924B E6001 E6002B E6012B E6013B E3813B or E6014B can accommodate up to four cordless handsets The handset provided with the E5901 E5911 E5921 or E6001 is automatically registered as handset 1 Additional handsets will be assigned numbers in the order they are registered handset 2 handset 3 and handset 4 You can register a maximum of four handsets The E5902B E5912B E5922B E6002B or E6012B has two hand sets automatically registered as handset 1 and 2 You can register two additional handsets which will be assigned numbers 3 and 4 The E5903B E5913B E5923B E3813B or E6013B has three handsets auto
4. matically registered as handsets 1 2 and 3 You can register one additional handset which will be assigned number 4 The E5904B E5914 E5924B E6014B has four pre registered handsets so you cannot register any additional handsets to it Getting started Adding and registering handsets PRESS HNOST LOC 4 SEC ON BASE PLEASE WAIT HS X REGISTERED 12 00PM Before using a new E598 2 handset you must register it with the telephone base Each handset must be registered seper ately To register a handset to your telephone base When first purchased the expansion hand set will show NOT REGISTERED on the screen The new handset may need to be charged for five minutes before registering to the main telephone base 1 Place the unregistered handset into the telephone base If PRESS HNDST LOC 4 SEC ON BASE does not appear on the handset screen after a few seconds lift up handset and place it in the telephone base again 2 On the telephone base press and hold HANDSET LOCATOR for about four seconds until the red IN USE light on the telephone base turns on and then release the button The handset will show PLEASE WAIT and will take about 10 seconds to complete the registration The handset will show HS X REGISTERED and will beep if the registration was successful a NOTES 1 If the registration was not successful the display will show NOT REGISTERED To reset the hand set lift the handset out of
5. registered handset and press the PHONE FLAsH button then press the 4 OFF c ear button and place the handset back into the base You may also reset by unplugging the power from the telephone base and plug it back in 2 You cannot de register the handset s if any phone connected to your phone line is in use 5 atat www telephones att com Copyright 2007 Advanced American Telephones All rights reserved AT amp T and the AT amp T logo are trademarks of AT amp T Knowledge Ventures licensed to Advanced American Telephones Printed in China Issue 2 03 07 91 001110 010 100
6. the telephone base or charger and replace it Try the registration process again 2 You cannot register a handset if any phone con nected to your phone line is in use Getting started Replacing a handset You may need to de register your handsets if You have the maximum number of registered handsets four and you need to replace a handset OR You wish to change the designated handset number of your reg istered handsets You must first de register ALL the handsets and then re register ALL the handsets you wish to use Please read carefully through all the instructions on this page before beginning the de registration process To de register all handsets 1 Press and hold HANDSET LOCATOR on the telephone base for about 10 seconds until the IN USE light turns on and starts to flash then release the HANDSET LOCATOR button 2 Immediately press and release HANDSET LOCATOR again You must press HANDSET LOCATOR while the IN USE light is still flashing The light flashes for about seven seconds 3 The handset s will show CONNECTING and it will take about 10 seconds to complete de registration ALL handsets will show NOT REGISTERED if de registration was successful 4 To re register the handset s to the telephone base follow the registration instructions on page 3 4 O NOTES 1 If the de registration process was not successful you may need to reset the system and try again To reset pick up any
Download Pdf Manuals
Related Search