Arxel Guild M118i User's Manual
Contents
1. DNS Server Address POP3 Server Address POP3 Login User Name Password Xerox WorkCentre M118i 2 Enabling Scan to E mail Enabling Scan to E mail To enable the Scan to E mail feature i 2 gt On the control panel press the Log In Out button Press the Select button below the display to select System Settings a Use the numeric keypad to enter the Password The default password is 11111 b Press the Select button to select Confirm Select Print Settings and then press the Enter button Press the Select button until you see Software Option on the display and then press the Enter button Use the numeric keypad to enter the Software Option password for Scan to E mail and then press the Enter button The password can be found on the inside cover of the Scan to E mail Instructions Configuring Scan to E mail After Scan to E mail is enabled follow these steps to configure Scan to E mail on your network Set the Administrator E mail Address 1 2 3 4 At your computer launch your web browser Enter the machine s IP address in the browser s Address field http XXX XXX XXX XXX Click the Properties tab Select Machine Details on the left sidebar a Enter the machine s email address in the Administrator E mail Address field If an email address for the machine has not been created enter your email address Once an email address is available for the M118i machine repeat Steps 1 throu2. Troubleshooting Scan to E mail If the machine reports an SMTP error use the following table to determine the cause and resolution Possible Cause Resolution Incorrect mail server host name m Verify that the correct corporate or ISP mail server name has been entered in the SMTP Host Name field m Ensure that DNS information is entered correctly Incorrect From E mail address entered Verify that the Administrator E mail Address is correct The E mail address must match what the corporate or ISP mail server is expecting The corporate or ISP mail server requires authentication Check with your network administrator or ISP to determine if the mail server requires authentication If so use CentreWare IS to enable POP before SMTP authentication and then enter the POP User Name and POP Password information The corporate or ISP mail server does not allow mail on the standard port number 25 Check with your network administrator or ISP to verify that Port 25 is being used for mail service If not obtain the mail service port information and then use CentreWare IS to configure it Xerox WorkCentre M118i 5
3. X R OX Xerox WorkCentre M118i scan to E mail 701P42574 Quick Setup Guide This guide provides a quick reference for setting up the Scan to E mail feature on the Xerox WorkCentre M118i It includes procedures for m Enabling Scan to E mail on page 3 m Configuring Scan to E mail on page 3 m Verifying Scan to E mail Setup on page 5 m Troubleshooting Scan to E mail on page 5 See also System Administrator Guide Provides detailed information about setting up E mail User Guide Provides step by step instructions for sending E mail Copyright 2004 Xerox Corporation All rights reserved 1 Before You Begin Before enabling and configuring Scan to E mail Verify that the machine is connected on a TCP IP network See the Network Connection Quick Setup Guide for more information Obtain the following information from your network administrator or Internet Service Provider ISP Required Administrator E mail Address Note Enter the e mail address created for the M118i machine in the Administrator E Mail Address field The email address populates the From portion of each e mail sent from the M118i machine If an email address for the machine has not been created enter your email address When an email address is created for the machine replace your e mail address with the machine s e mail address See Configuring Scan to E mail on page 3 SMTP Server Address Local E mail Address for testing Optional
4. gh 5 in this procedure to replace your e mail address with the machine s email address b Click the Apply New Settings button at the bottom of the page c Enter the CentreWare IS administrator s User Name and Password and then click the OK button Note The default CentreWare IS administrator s User Name is admin and Password is x admin These should be changed after network setup is complete d At the reboot prompt click the Reboot button Wait one minute for the reboot to complete and then click the browser Refresh button Xerox WorkCentre M118i 3 Configuring Scan to E mail Enable the E mail Ports 1 Click the Properties tab 2 Select Port Status on the left sidebar a Enable the SNMP Send E mail and Mail Notice Service ports Do not modify the other port settings on this page b Click the Apply New Settings button at the bottom of the page C At the reboot prompt click the Reboot button 3 Wait one minute for the reboot to complete and then click the browser Refresh button Enter the SMTP Settings 1 Click the Properties tab 2 Select the Protocol Settings folder on the left sidebar and then select E mail a Enter the SMTP Server Address b If SMTP authentication is required enter the POP3 Server Address POP User Name and POP Password Note The POP3 Server Address can be entered as an IP address or a server name c Ifthe machine uses a host name rather than an IP address click TCP IP in the
5. left side bar and verify that the DNS Address 1 field contains the DNS Server Address For more information see the Network Connection Quick Setup Guide d Click the Apply New Settings button at the bottom of the page e At the reboot prompt click the Reboot button 3 Wait one minute for the reboot to complete and then click the browser Refresh button Create an Address Book Entry to Use for Verifying Scan to E mail Setup 1 2 Click the Properties tab Select Address Book on the left sidebar a Type a Speed Dial number from 1 200 to assign to the test recipient and then click the Edit button Select E mail from the Address Type drop down list Enter the recipient s local E mail address in the Recipient Address field Enter the Recipient Name Click the Apply New Settings button e295 Xerox WorkCentre M118i 4 Verifying Scan to E mail Setup Verifying Scan to E mail Setup Send a test E mail to verify the Scan to E mail setup 1 Load a sample document into the document feeder 2 On the control panel press the E mail button 3 Press the Address Book button 4 Inthe menu highlight the address book entry you created and then press the Next Address button to select it i Press the Enter button m Press the green Start button to scan the document and send it as an attachment to the selected recipient 7 Verify that the recipient received the E mail with the scanned document as an attachment
Download Pdf Manuals
Related Search