American Standard T038.900 User's Manual
Contents
1. Installation Instructions DECK MOUNT TO38 900 TUB SYSTEMS TROPIC TRIM KIT with EverClean Finish Congratulations on purchasing your American Standard faucet with EverClean finish found only on American Certified to comply with ANSI A112 18 1 Standard faucets U S Patent No D403 750 EverClean Finish M968896 One wipe effortlessly removes spots Eliminates the need for cleaners and scrubbing Permanent surface protectant remains beautiful for the life of the faucet e EverClean available on Polished Chrome Satin Nickel Stainless Steel Polished Brass or any combination of these finishes To ensure that your installation proceeds smoothly please read these instructions carefully before you begin Required Tools 3 Phillips Screwdriver 0S OO RY Adjustable Wrench 3 Channel Locks Drill with 3 16 bit Flat Blade Screwdriver SPOUT INSTALLATION Complete FINISHED DECK before trim installation Turn off the water supplies A 3 r REMOVE ALL Remove the GUARDS 1 from the VALVE BODIES 2 Remove the m BE A GUARD 3 and 1 4 PLUG 4 from the SPOUT SHANK 5 1 i 9 The SPOUT SHANK 5 height should be 1 to 2 above the FINISHED DECK Cut the SPOUT SHANK 5 if necessary Remove all burrs and bevel the end of the shank Failure to do so may damage the SPOUT O ring during installation and cause water leakage Drill a 3 16 hole i2. llation DECK MOUNT Instructions TUB FILLERS TO38 990 TROPIC DIVERTER amp PERSONAL SHOWER TRIM KITS with EverClean Finish Congratulations on purchasing your American Standard faucet with EverClean finish found only on American Standard faucets Certified to comply with ANSI A112 18 1 EverClean Finish U S Patent No 403 750 One wipe effortlessly removes spots M968897 Eliminates the need for cleaners and scrubbing Permanent surface protectant remains beautiful for the life of the faucet e EverClean available on Polished Chrome Satin Nickel Stainless Steel Polished Brass or any combination of these finishes To ensure that your installation proceeds smoothly please read these instructions carefully before you begin INSTALL HANDLE ADAPTER Remove DIVERTER GUARD 1 from valve Place the ESCUTCHEON SEAL 7 into groove of DECK ADAPTER 2 Align the HANDLE STEM 3 with the SLEEVE 4 as necessary Thread the HANDLE ADAPTER 5 into the VALVE BODY 6 until the DECK ADAPTER 2 contacts tight against the finished mounting surface INSTALL HANDLES Push ADAPTER 1 on VALVE STEM 2 so that the hole of the ADAPTER 1 without a spline is facing up Fig A Tighten STEM SCREW 3 to I THREAD ON secure ADAPTER 1 poe Find correct position of LEVER HANDLE ASSEMBLY 4 by adjusting male teeth on ADAPTER 1 to female teeth in HANDLE 4 Thread LEVER HANDLE ASSEMBLY 4 onto DECK ADAPTER 5 until s
3. n the finished deckfor spout locking pin See TEMPLATE for location 21 64 L 3 16 DIA HOLE r 18 6mm DIA 23 32 a 47764 SPOUT SHANK TEMPLATE FOR SPOUT ROLL i PIN LOCATION AS DRILLED 1 A SPOUT INSTALLATION Lubricate the SPOUT ADAPTER O RING 6 and SPOUT O RING 7 oh Push SPOUT ADAPTER 8 on SPOUT SHANK 5 and ale slot in SPOUT ADAPTER 8 with 3 16 FINISHED drilled hole DECK Tighten SPOUT ADAPTER SET SCREW 9 securely with 4mm HEX KEY 10 supplied Position the RUBBER RING 14 in the groove in the base of the ESCUTCHEON 1911 Push the SPOUT 12 with ESCUTCHEON 14 down onto the SPOUT ADAPTER 8 and tighten the SET SCREW 13 securely with the Smm HEX KEY 15 supplied INSTALL HANDLE ADAPTERS Place the ESCUTCHEON SEALS 1 into groove of DECK ADAPTERS 2 m Align the HANDLE STEM 3 with the SLEEVE 4 as necessary E Thread the HANDLE ADAPTER 5 into the VALVE BODY 6 until the DECK ADAPTERS 2 contacts tight against the finished deck INSTALL HANDLES Push ADAPTER 1 on VALVE STEM 2 so that the hole of the ADAPTER 1 without a spline is od up See figure A Tighten STEM SCREW 3 to secure ADAPTER 1 Find correct position of LEVER HANDLE ASSEMBLY 4 by adjusting male teeth on ADAPTER 1 to female teeth in HANDLE 4 THREAD ON Thread LEVER HANDLE ASSEMBLY 4 onto DECK TO DECK ADAPTER 5 until snug against mounting surface ADAPTER Repeat step
4. nug against mounting surface INSTALL HAND SHOWER Unscrew the HOLDER 1 from the SHOWER ESCUTCHEON 2 Slip the SHOWER HOSE 3 through the SHOWER ESCUTCHEON 2 and the HOLDER 1 Pull out the SLEEVE GUARD 6 and HOSE 7 Unthread the SLEEVE GUARD G from the HOSE END 8 connection Be careful not to allow the HOSE 7 to fall back through the SLEEVE 9 Insert SEAL WASHER 10 into the SHOWER HOSE CONNECTOR 111 Thread the SHOWER HOSE CONNECTOR 11 onto the HOSE END 8 and tighten securely Thread the SHOWER ESCUTCHEON 2 into the SLEEVE 9 until the SHOWER ESCUTCHEON 2 contacts the finished deck Loosen the SET SCREW 12 in the SHOWER ESCUTCHEON 2 and rotate the ESCUTCHEON 2 so that SET SCREW 12 faces the center of the tub Retighten the SET SCREW 12 Thread the HOLDER 1 into the SHOWER ESCUTCHEON 2 Insert a SEAL WASHER 4 into the SHOWER HOSE CONNECTOR 5 and hand tighten HAND SHOWER 13 into SHOWER HOSE CONNECTOR 5 Place the HAND SHOWER 13 into the HOLDER 1 Turn DIVERTER VALVE 1 fully clockwise Tub fill position Turn on control valves and check all connections for leaks With DIVERTER VALVE 1 in clockwise position flow should only come from tub spout Lift HANDSHOWER 2 from holder direct spray into tub turn DIVERTER VALVE 1 fully counter clockwise to check HANDSHOWER 2 and HOSES 3 for leaks With DIVERTER VALVE 1 in counter clockwise position flow
5. s for opposite handle Figure A SPLINE END DOWN a M968896 Turn the HOT HANDLE clockwise and the COLD HANDLE counterclockwise to the off position E Unscrew and remove the STREAM STRAIGHTENER m Slowly turn on the water supplies operae the HANDLES to flush water lines thoroughly Check SPOUT connection for leakage Turn the Handles off Replace the SPOUT END HOT HANDLE SERVICE To change the direction of handle rotation Turn off the water supplies Turn HANDLE 1 to the off position Unthread the HANDLE BASE 2 from HANDLE ADAPTER 3 Unthread HANDLE ADAPTER 3 and remove Remove VALVE LOCKNUT 4 A 17mm deep socket is required Remove the CARTRIDGE 5 by pulling up on the SLEEVE 6 Remove SCREW 7 and pull off SLEEVE 6 Remove the SPRING CLIP 8 Remove the STOP WASHER 9 Turn it 90 and replace Replace the SPRING CLIP 8 Reverse the above steps to reassembly the components If the spout drips operate the handles several times from the off to the on position Do not force the handles only turn 90 CARE INSTRUCTIONS EverClean Finish Care Instructions American Standard s EverClean finish will wipe clean with a soft dry cloth A soft cloth with clean water may also be used if desired No additional cleaning products are required DO NOT USE Soaps acid polish abrasives harsh cleaners or a cloth with a coarse surface M968896 Ambrican Standard Insta
6. should only come from HANDSHOWER 2 Turn control valves off 5 EverClean Finish Care Instructions American Standard s EverClean finish will wipe clean with a soft dry cloth A soft cloth with clean water may also be used if desired No additional cleaning products are required DO NOT USE Soaps acid polish abrasives harsh cleaners or a cloth with a coarse surface M968897
Download Pdf Manuals
Related Search