American Standard One 2064.400 User's Manual
Contents
1. Locked mode insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the sink and the American Standard logo is facing front Rotate stopper slightly if necessary so that the Stopper slides all the way down Fig G E Re install the Cam into the Drain rotating the Cam if necessary to make sure tt is fully inserted Fig J m Re install the Cam Cap making sure the guide teeth are facing ania arenes outward If the Cam Cap does not snap into place then rotate the Cam to make sure it is fully inserted Fig K E Re attach Cable See CABLE ADJUSTMENT PROCEDURE in Locked Mode Troubling Shooting Guide to complete installation Stopper will be Vandal Proof in Locked mode and not be removable Unlocked Mode m Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper Fig H m To install the stopper in Unlocked mode insert the Stopper into the Drain so that the Plastic Loop is facing toward the front of the sink and the American Standard logo is facing rear Rotate Stopper slightly if necessary so that the Stopper slides all the way down Fig H E Re install the Cam into the Drain rotating the Cam if necessary to make sure tt is fully inserted Fig J lt LOOP TOWARD E Re install the Cam Cap making sure the guide teeth are facing FRONT OF BIDET outward If the Cam Cap does not snap into place then rotate the Ca2. AYE EverClean Finish Care Instructions American Standard s EverClean finish will wipe clean with a soft dry cloth Turn valve to OFF position A soft cloth with clean water Thread counter clock wise HANDLE BASE 1 to remove 1 may also be used if desired HANDLE ASSEMBLY 2 from ESCUTCHEON BASE 3 No additional cleaning products Use a flat blade screw driver to remove SPRING CLIP 4 are required Lift STOP WASHER 5 turn 90 and replace Replace SPRING CLIP 4 DO NOT USE Soaps acid m Reinstall HANDLE ASSEMBLY 2 polish abrasives harsh If spout drips operate handles several times from OFF cleaners or a cloth with a to ON position Do not force handles turn only 90 coarse surface E To change direction of handle rotation proceed as follows UNTHREAD M968924 SpeedConnect Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the down position e Follow CABLE ADJUSTMENT PROCEDURE If Stopper does not raise up fully or sink drains too slowly e Follow CABLE ADJUSTMENT PROCEDURE If you need to remove the Stopper e Follow STOPPER REMOVAL PROCEDURE If you would like the ability to remove your Stopper simply by lifting it out of the drain e Follow STOPPER INSTALLATION PROCEDURE for Unlocked mode CABLE ADJUSTMENT PROCEDURE Disconnect the Cable from the Drain by threading the Cable Connector 1 counter clockwise Fig A Look
3. ADJUSTMENT PROCEDURE If Stopper does not raise up fully or sink drains too slowly e Follow CABLE ADJUSTMENT PROCEDURE If you need to remove the Stopper e Follow STOPPER REMOVAL PROCEDURE If you would like the ability to remove your Stopper simply by lifting it out of the drain e Follow STOPPER INSTALLATION PROCEDURE for Unlocked mode CABLE ADJUSTMENT PROCEDURE Disconnect the Cable from the Drain by threading the Cable Connector 1 counter clockwise Fig A Look at the area on the Drain Body where the Cable was attached and locate the component labeled as Cam in the illustration Fig B Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go At this point the Stopper should be in the UP position Fig B C Push DOWN on the Lift Knob to make sure it is fully down Fig C Re attach the Cable to the Drain Body Connection 2 by threading the Cable Connector 1 clockwise onto the Drain Body Connection 2 and hand tighten Fig A STOPPER STOPPER REMOVAL PROCEDURE Disconnect the Cable from the Drain by threading the Cable Connector 1 counter clockwise Fig A Look at the area on the Drain Body where the Cable was attached and locate the component labeled as Cam and Cam Cap in the illustration Fig B Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain Fig D Remove the Cam by pulling it straight ou
4. Americam Standard Installation Instructions ONE 2064 400 Bidet Faucet and Transfer Valve with EverClean Finish amp SpeedConnect Drain Congratulations on purchasing your American Standard faucet with EverClean finish and Speed Connect drain two features found only on American Standard faucets Certified to comply with ANSI A112 18 1 EverClean Finish SpeedConnect Drain meee e One wipe effortlessly removes spots e Fewer parts installs in less time e Eliminates the need for cleaners and scrubbing e No tools needed e Permanent surface protectant remains beautiful Never needs adjustment for the life of the faucet e Guaranteed to seal properly the first time every time Your new American Standard faucet is designed to work only with the SoeedConnect drain Heplful tips for removing your current drain can be found in the Troubleshooting section of these instructions To ensure that your installation proceeds smoothly please read these instructions carefully before you begin Roughing in 8 TO 12 Required tools TRANSFER VALVE FINISHED lt gt Dimensions fon nvedNe MAL BIDET OUTLINE IM OR SPRAY IS IS SYMBOLIC 7 8 DIA bs 5 l Screwdriver Sts Putty or oa L aL aulking lt H 2 1 8 o SSPRAY NTO 2 1 4 PIA gy lt L sya D i l l N Phillips Screwdriver 3 7 8 i ar n FOR GROUND JOINT Channel Locks DIA m CONNECTION OR 1 2 Il rit O D SLIP INLETS N TT REAR VIEW WITH WA
5. EAL WASHER 3 is properly seated Fig B WHITE FOAM ILLUSTRATION GASKET E From below slip slot in MOUNTING NUT 4 over CABLE 5 ied Ye VALVES Thread NUT 4 onto lift rod guide shank to secure ROD GUIDE 1 to bidet Hand tighten only Fig B M968923 1 0 TEE AND HOSE CONNECTION ATTACH CABLE CONNECTOR POP UP KNOB 1 must be fully down Fig A Thread CABLE CONNECTOR 1 i AEN clockwise onto DRAIN BODY A eS CONNECTION 2 and hand AWA CA X x r R tighten Fig B cus E le Your new POP UP DRAIN installation is now complete Fig C Note Tailpeice on pop up drain 1 1 4 O D is 1 1 4 O D Fig C CHECK OPERATION OF POP UP Operate LIFT KNOB 1 to verify that STOPPER 2 opens and closes Note If STOPPER 2 does not open and close properly then refer to the troubleshooting section of these instructions INSTALL DIVERTER KNOB Push DIVERTER KNOB 1 onto HANDLE ADAPTER 2 Push on RING 3 and tighten with SCREW 4 Press on KNOB CAP 5 Note Screwdriver gap is for disassembling and should point downwards Insert SEAL 1 into ADAPTER 2 and tighten ADAPTER 2 to bottom of TRANSFER VALVE 3 Install SEAL 4 into coupling nut of TEE 5 and tighten connection to ADAPTER 2 Connect HOSE COUPLING NUTS 6 to Hot and Cold valve bodies and securely tighten WATER SUPPLY CONNECTION NOTE FLEXIBLE SUPPLIES OR BULL NOSE R
6. ISERS NOT INCLUDED AND MUST BE PURCHASED SEPARATELY Connect water supply to VALVE BODIES 7 7a with Le i 1 2 IPS FLEXIBLE SUPPLIES 2 or 3 8 0 D BULL NOSE RISERS 3 Use adjustable wrench to tighten connections Do not over tighten Be careful not to kink copper supply when FLEXIBLE bending Use tubing cutter to cut to proper length SUPPLIES 3 8 O D BULL NOSE RISERS COMPRESSION NUT Connect HOT water supply to inlet of left SHANK and COLD water supply to right SHANK using sealant appropriate connectors and COUPLING NUTS Connect 1 1 4 O D tailpiece on POP UP DRAIN to waste outlet CONNECT TO WASTE OUTLET 3 8 COMPRESSION CONNECTION M968923 INSTALL HANDLES E Push ADAPTER 1 on VALVE STEM 2 so that the hole of the ADAPTER 1 without a spline is facing up See figure A Tighten STEM SCREW 8 to secure ADAPTER 1 THREAD ON TO DECK ADAPTER m Find correct position of LEVER HANDLE ASSEMBLY 4 by adjusting male teeth on ADAPTER 1 to female teeth in HANDLE 4 Thread LEVER HANDLE ASSEMBLY 4 onto ESCUTCHEON 5 until snug against mounting surface Figure A sect ball NN uiii SPLINE END mn 7 1 Pd TEST INSTALLED FITTING m With HANDLES 1 in OFF position turn on WATER SUPPLIES 2 and check all connections for leaks m m Operate both HANDLES 1 to flush water lines thoroughly E Rotate TRANSFER VALVE 5 from rim wash to
7. LL REMOVED Adjustable Wrench Tubing Cutter Turn off hot and cold water CAUTION supplies before beginning 1 BIDET FAUCET INSTALLATION Place RUBBER RING 10 into ESCUTCHEON 4 Install LOCKNUT 1 and RUBBER WASHER 2 onto VALVE BODIES 3 3a From under side of mounting surface install VALVE BODY 3 3a through valve mounting holes Threads of VALVE BODY 3 3a should extent at least 5 16 of a inch above mounting surface top Fig A Thread ESCUTCHEON 4 onto VALVE BODIES 3 3a until snug against internal stop If necessary adjust LOCKNUT 1 E Tighten LOCKNUTS 1 with WRENCH 5 supplied to secure VALVE BODIES 3 3a m Remove ESCUTCHEON 6 WASHER 7 and 10 UPPER GASKET 8 from TRANSFER VALVE 9 MOUNTING Insert TRANSFER VALVE 9 into the center forward SURFACE hole of BIDET E Replace UPPER GASKET 8 and WASHER 7 and ESCUTCHEON 6 until it locks against internal stop Position the side threaded outlet rearward and secure MOUNTING NUT 11 SPRAY INSTALLATION Assemble SPRAY BODY 1 to BIDET Using putty seal underside of SPRAY BODY FLANGE 2 and secure with NUT 3 Thread SPRAY HOSE 4 with SEAL WASHER 5 to SPRAY BODY 1 Connect other end of HOSE 4 with SEAL WASHER 6 to side outlet NIPPLE 7 of the TRANSFER VALVE 8 Thread SPRAY CAP 9 onto SPRAY BODY 1 3 POP UP DRAIN Remove CLEAR PLASTIC COVER 1 Remove CARDBOARD SPACER 2 fr
8. at the area on the Drain Body where the Cable was attached and locate the component labeled as Cam in the illustration Fig B Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go At this point the Stopper should be in the UP position Fig B C Push DOWN on the Lift Knob to make sure it is fully down Fig C Re attach the Cable to the Drain Body Connection 2 by threading the Cable Connector 91 clockwise onto the Drain Body Connection 2 and hand tighten Fig A STOPPER REMOVAL PROCEDURE Disconnect the Cable from the Drain by threading the Cable Connector 1 counter clockwise Fig A Look at the area on the Drain Body where the Cable was attached and locate the component labeled as Cam and Cam Cap in the illustration Fig B Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain Fig D Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal Fig E The Stopper can now be removed by lifting it out of the Drain Fig F AOT tana REMOVE CAM CAP M968924 STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways Locked Mode Stopper cannot be removed or Unlock Mode Stopper is removable Locked Mode m Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper Fig G E To install the stopper in
9. emble SPRAY BODY 1 to BIDET Using putty seal underside of SPRAY BODY FLANGE 2 and secure with NUT 3 Thread SPRAY HOSE 4 with SEAL WASHER 5 to SPRAY BODY 1 Connect other end of HOSE 4 with SEAL WASHER 6 to side outlet NIPPLE 7 of the TRANSFER VALVE 8 Thread SPRAY CAP 9 onto SPRAY BODY 1 3 POP UP DRAIN E Remove CLEAR PLASTIC COVER 1 E Remove CARDBOARD SPACER 2 from under DRAIN POP UP 3 E Tighten TAILPIECE 4 on DRAIN BODY before installing DRAIN BODY Fig B 4 REMOVE FLANGE E Thread FLANGE 1 counter clockwise and remove FLANGE 1 and FOAM GASKET 2 from drain body Fig A mM Thread LOCKNUT 3 clock wise to bottom of drain body Push GASKET 4 down against LOCKNUT 3 Fig B INSTALL DRAIN FROM BELOW FIXTURE From under side of BIDET Tighten LOCKNUT 1 firmly with Adjustable install DRAIN BODY 1 up Wrench or Channel Locks through drain outlet Note No plumber s putty or caulk is required The CABLE ATTACHMENT POINT 2 must face towards the rear of the BIDET Install FOAM GASKET 3 and FLANGE 4 onto drain body from above BIDET and tighten FLANGE 4 firmly FLANGE GASKET Check DRAIN FLANGE in BIDET to ensure that WHITE FOAM GASKET 1 is fully compressed and not visible Fig A POP UP ROD ASSEMBLY SLOTTED E Insert LIFT ROD GUIDE 1 and CABLE CONNECTOR 2 through rear hole making sure S
10. er into the Drain so that the Plastic Loop is facing toward the front of the sink and the American Standard logo is facing rear Rotate Stopper slightly if necessary so that the Stopper slides all the way down Fig H E Re install the Cam into the Drain rotating the Cam if necessary to make sure tt is fully inserted Fig J lt LOOP TOWARD m Re install the Gam Cap making sure the guide teeth are facing FRONT OF BIDET outward If the Cam Cap does not snap into place then rotate the Cam to make sure it is fully inserted Fig K E Re attach Cable See CABLE ADJUSTMENT PROCEDURE in Unlocked Mode Troublingshooting Guide to complete installation Stopper will be in Unlocked mode and removable INSTALL CAM CAP M968923
11. er to cut to proper length E Connect HOT water supply to inlet of left SHANK and COLD water supply to right SHANK using sealant appropriate connectors and COUPLING NUTS CONNECT TO WASTE OUTLET E Connect 1 1 4 O D tailpiece on POP UP DRAIN to HOT 3 8 COMPRESSION waste outlet CONNECTION M968924 INSTALL HANDLES E Push ADAPTER 1 on VALVE STEM 2 so that the hole of the ADAPTER 19 without a spline is facing up See figure A Tighten THREAD ON STEM SCREW 3 to secure ADAPTER 1 FO DECK Find correct position of LEVER HANDLE ASSEMBLY 4 by adjusting male teeth on ADAPTER 1 to female teeth in HANDLE 4 Thread LEVER HANDLE ASSEMBLY 4 onto ESCUTCHEON 5 until snug against mounting surface 1 2 TEST INSTALLED FITTING m With HANDLES 1 in OFF position turn on WATER OUTLINE OF BIDET SUPPLIES 2 and check all connections for leaks m m Operate both HANDLES 1 to flush water 4 lines thoroughly E Rotate TRANSFER VALVE 5 from rim wash to spray several times to check operation 1 3 CHECK DRAIN CONNECTIONS WAC VVS E Pull up POP UP KNOB 3 and fill Bidet with water Check that DRAIN STOPPER 4 makes a good seal and retains water in Bidet If STOPPER 4 does not seal properly please refer to Troubleshooting Guide in these instructions Vi VVV VVV E Push POP UP KNOB 3 down and check all drain connections and P trap for leaks m Tighten if necessary
12. m to make sure it Is fully inserted Fig K m Re attach Cable See CABLE ADJUSTMENT PROCEDURE in Unlocked Mode Troublingshooting Guide to complete installation Stopper will be in Unlocked mode and removable INSTALL CAM CAP M968924 Amtrican Standard Installation Instructions ONE 2064 401 Bidet Faucet and Vacuum Breaker with EverClean Finish amp SpeedConnect Drain Congratulations on purchasing your American Standard faucet with EverClean finish and Speed Connect drain two features found only on American Standard faucets EverClean Finish e One wipe effortlessly removes spots a oaa a e Eliminates the need for cleaners and scrubbing SpeedConnect Drain Permanent surface protectant remains beautiful tae sek see in less time for the life of the faucet Ever eed aa eat EverClean available on Polished Chrome Satin Nickel Guaranteed to seal properly the first time every time Stainless Steel Polished Brass or any combination of these finishes Certified to comply with ANSI A112 18 1 Your new American Standard faucet is designed to work only with the SoeedConnect drain To ensure that your installation proceeds smoothly please read these instructions carefully before you begin Roughing in Dimensions Required tools DIVERTER AND C_D VACUUM BREAKER ASSEMBLY c ye TRANSFER VALVE FOR FLUSHING imi RIM OR SPRAY Lt BIDET OUTLINE i Screwdri
13. om under DRAIN POP UP 3 Tighten TAILPIECE 4 on DRAIN BODY before installing DRAIN BODY Fig B 4 REMOVE FLANGE E Thread FLANGE 1 counter clockwise and remove FLANGE 1 and FOAM GASKET 2 from drain body Fig A E Thread LOCKNUT 3 clock wise to bottom of drain body Push GASKET 4 down against LOCKNUT 3 Fig B INSTALL DRAIN FROM BELOW FIXTURE 6 TIGHTEN LOCKNUT From under side of BIDET install DRAIN BODY 1 up through drain outlet Tighten LOCKNUT 1 firmly with Adjustable Wrench or Channel Locks Note No plumber s putty or caulk is required The CABLE ATTACHMENT POINT 2 must face towards the rear of the BIDET Install FOAM GASKET 3 and FLANGE 4 onto drain body from above BIDET and tighten FLANGE 4 firmly FLANGE GASKET Check DRAIN FLANGE in BIDET to ensure that WHITE FOAM GASKET 1 is fully compressed and not visible Fig A POP UP ROD ASSEMBLY E Insert LIFT ROD GUIDE 1 and CABLE CONNECTOR 2 through rear hole making sure SEAL WASHER 3 is properly seated Fig B i ASKET ILLUSTRATION E From below slip slot in MOUNTING NUT 4 over CABLE 5 NOT VISIBLE ar aaa i 2 Thread NUT 4 onto lift rod guide shank to secure ROD GUIDE 1 to bidet Hand tighten only Fig B M968924 NUT SLOTTED ene ATTACH CABLE CONNECTOR POP UP KNOB 1 must be fully down Fig A Thread CABLE CONNECTOR 1 clockwi
14. se onto DRAIN BODY CONNECTION 2 and hand tighten Fig B Your new POP UP DRAIN installation is now complete Fig C Note Tailpeice on pop up drain is 1 1 4 O D Fig C 9 CHECK OPERATION OF POP UP E Operate LIFT KNOB 1 to verify that STOPPER 2 Opens and closes Note If STOPPER 2 does not open and close properly then refer to the troubleshooting section of these instructions INSTALL DIVERTER KNOB E Push DIVERTER KNOB 1 onto HANDLE ADAPTER 2 E Push on RING 8 and tighten with SCREW 4 m Press on KNOB CAP 5 Note Screwdriver gap is for disassembling and should point downwards 1 0 TEE AND HOSE CONNECTION OUTLINE OF PREN E Insert SEAL 1 into ADAPTER 2 and tighten ADAPTER 2 to side of TRANSFER VALVE 3 m Install SEAL 4 into coupling nut of TEE 5 and tighten at W Ee oS Ja connection to ADAPTER 2 y NG Zo g Connect HOSE COUPLING NUTS 6 to Hot and Cold valve COUPLING bodies and securely tighten NUT 7 9 3 8 O D ii BULL NOSE 1 2 PIPE RISERS WATER SUPPLY CONNECTION THREAD NOTE FLEXIBLE SUPPLIES OR BULL NOSE RISERS NOT a INCLUDED AND MUST BE PURCHASED SEPARATELY 2 E Connect water supply to VALVE BODIES 7 7a with FLEXIBLE 1 2 IPS FLEXIBLE SUPPLIES 8 or 3 8 0 D BULL NOSE SUPPLIES lt ie age RISERS 9 Use adjustable wrench to tighten connections Do not over tighten Be careful not to kink copper supply when bending Use tubing cutt
15. spray several times to check operation NE Vi 1 3 CHECK DRAIN CONNECTIONS WA AVAVAVAVATATANNA E Pull up POP UP KNOB 3 and fill Bidet with water Check that DRAIN STOPPER 4 makes a good seal and retains water in Bidet If STOPPER 4 does not seal properly please refer to Troubleshooting Guide in these instructions I LIV A VVVVV E Push POP UP KNOB 3 down and check all drain connections and P trap for leaks m Tighten if necessary x Ky Wavavaval EverClean Finish Care Instructions American Standard gt EverClean E To change direction of handle rotation finish will wipe clean with a soft proceed as follows dry cloth Turn valve to OFF position A soft cloth with clean water Thread counter clock wise HANDLE BASE 1 to remove 1 may also be used if desired HANDLE ASSEMBLY 2 from ESCUTCHEON BASE 3 UNTHREAD No additional cleaning products Use a flat blade screw driver to remove SPRING CLIP 4 are required Lift STOP WASHER 5 turn 90 and replace Replace SPRING CLIP 4 DO NOT USE Soaps acid Reinstall HANDLE ASSEMBLY 2 polish abrasives harsh If spout drips operate handles several times from OFF cleaners or a cloth with a to ON position Do not force handles turn only 90 coarse surface M968923 SpeedConnect Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the down position e Follow CABLE
16. t while wiggling gently to loosen the Rubber Seal Fig E The Stopper can now be removed by lifting it out of the Drain Fig F Ae CAM REMOVE CAM CAP M968923 STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways Locked Mode Stopper cannot be removed or Unlock Mode Stopper is removable Locked Mode m Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper Fig G E To install the stopper in Locked mode insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the sink and the American Standard logo is facing front Rotate stopper slightly if necessary so that the Stopper slides all the way down Fig G E Re install the Cam into the Drain rotating the Cam if necessary to make sure it is fully inserted Fig J m Re install the Cam Cap making sure the guide teeth are facing e EET outward If the Cam Cap does not snap into place then rotate the Cam to make sure it is fully inserted Fig K E Re attach Cable See CABLE ADJUSTMENT PROCEDURE in Locked Mode Troubling Shooting Guide to complete installation Stopper will be Vandal Proof in Locked mode and not be removable Unlocked Mode Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper Fig H m To install the stopper in Unlocked mode insert the Stopp
17. ver Plumbers Putty or IS SYMBOLIC N 7 8 DIA Lt Caulking cS _ C 1 316 Da ADJ 1 1 4 _ 2 1 8 lt lt TO 2 1 4 DIA Phillips Screwdriver H 1 3 8 ere FOR GROUND JOINT D j CONNECTION OR 1 2 Se ts D e Ai O D SLIP INLETS 5 1 2 T REAR VIEW WITH l FINISHED WALL REMOVED Adjustable Wrench Channel Locks SS Oy ii 1 1 4 0 D TAILPIECE Tubing Cutter BIDET FAUCET INSTALLATION BWI cuppiies before beginning Place RUBBER RING 10 into ESCUTCHEON 4 Install LOCKNUT 4 and RUBBER WASHER 2 onto VALVE BODIES 3 3a From under side of mounting surface install VALVE BODY 3 3a through valve mounting holes Threads of VALVE BODY 3 3a should extent at least 5 16 of a inch above mounting surface top Fig A Thread ESCUTCHEON 4 onto VALVE BODIES 3 3a until snug against internal stop If necessary adjust LOCKNUT 1 m Tighten LOCKNUTS 1 with WRENCH 5 supplied a LEDGE to secure VALVE BODIES 3 3a Fig A 4 10 m Remove MOUNTING NUT 6 WASHER 7 and 5 16 UPPER GASKET 8 from TRANSFER VALVE 9 y MIN SURFACE z Insert TRANSFER VALVE 9 into the center forward hole of BIDET 4 3 E Replace UPPER GASKET 8 and WASHER 7 Position 1 the side threaded outlet rearward and secure MOUNTING 3 3 NUT 6 Thread ESCUTCHEON 11 onto TRANSFER va VALVE 9 until it seats against the BIDET LEDGE SPRAY INSTALLATION Ass
Download Pdf Manuals
Related Search