American Standard Culinaire 4137.100 User's Manual
Contents
1. CARTRIDGE 6 and MANIFOLD 7 E Reassemble CARTRIDGE 6 alternately tightening SCREWS 5 Replace CAP 4 and HANDLE 3 check flow 6 EverClean Finish Care Instructions American Standard s EverClean finish will wipe clean with a soft dry cloth A soft cloth with clean water may also be used if desired No additional cleaning products are required DO NOT USE Soaps acid polish abrasives harsh cleaners or a cloth with a coarse surface M968208 REV 1 12. the SCREWS 9 on LOCKNUT 7 Work your way around LOCKNUT 7 tightening the screws slightly each time until all are snug to ensure even pressure P MAKE WATER SUPPLY CONNECTIONS E D NOTE FLEXIBLE SUPPLIES HAVE TO BE PURCHASED SEPARATELY m Carefully bend COPPER SUPPLIES to meet water supply lines using the palms of the hands to avoid kinking E Connect HOT water supply line to left tube and COLD water supply line to right tube using appropriate connectors Use 1 2 IPS FLEXIBLE SUPPLIES 3 or 3 8 0 D BULL NOSE RISERS 4 Use adjustable wrench to tighten connections Do not over tighten Be careful not to kink See copper supply when bending Use tubing cutter to cut to proper length an TTT gt S VIII v 3 CONNECT SPRAY HOSE Slide COUPLING NUT 1 onto HOSE 2 E Place WASHER 8 into COUPLING NUT 1 on HOSE 2 Thread COUPLING NUT 19 onto HAND SPRAY 4 and tighten E Feed small end of HOSE 2 through BODY 5 so HAND SPRAY 4 rests inside SPRAY HOLDER 6 m Pull KNURLED NUT 7 down over HOSE 2 thread faces to the small end of the hose E Put SMALL RUBBER WASHER 8 in HOSE NUT 9 and screw HOSE NUT 9 onto HOSE END 10 and tighten E Pull KNURLED NUT 7 up over HOSE NUT 9 Place WASHER 91 into KNURLED NUT 7 Thread KNURLED NUT 7 onto OUTLET TUBE ADAPTER 12 and tighten E With HAND SPRAY 4 seated in SPRAY HOLDER 6 install WEIGHTS 13 onto HOSE 2 using t
3. Installation Instructions Culinaire 4137 100 Single Control Kitchen Faucet and Deluxe Pull Out Spray with EverClean Finish Congratulations on purchasing your American Standard faucet with EverClean finish found only on American Standard faucets EverClean Finish e One wipe effortlessly removes spots e Eliminates the need for cleaners and scrubbing e Permanent surface protectant remains beautiful for the life of the faucet e EverClean available on Polished Chrome Satin Nickel Stainless Steel Polished Brass or any combination of these finishes To ensure that your installation proceeds smoothly please read these instructions carefully before you begin TOOLS REQUIRED N p Phillips Screwdriver Channel Locks Adjustable Wrench Plumbers Putty or Caulking Tubing Cutter Certified to comply with ANSI A112 18 1M M968208 REV 1 1 1 INSTALL FITTING WITH OR WITHOUT DECK ESCUTCHEON anpi a fees Meaney Apply a bead of putty to bottom edge of ESCUTCHEON 1 Note Installation of ESCUTCHEON 1 is optional Make certain the large O RING 2 is properly seated in recess of faucet body Insert supply TUBES 3 and SHANK 4 through center hole of ESCUTCHEON 1 if used and sink Assemble RUBBER WASHER 5 BRASS WASHER 6 and threaded LOCKNUT 7 onto SHANK 4 from underside of sink Hand tighten LOCKNUT 7 and check that rotation of HANDLE 8 from HOT to COLD is centered Use a screwdriver to tighten
4. wo SCREWS 14 Locate the WEIGHTS 13 two feet 2 from the underside of the sink deck Tighten SCREWS 14 firmly M968208 REV 1 1 E With HANDLE 1 down in off position E Pull HAND SPRAY 2 from FAUCET 5 m Move HANDLE 1 down into off and disconnect HAND SPRAY 2 Pull position HOSE 3 HOSE should pull m Turn on water supplies and check approximately 2 feet and direct open all connections for leaks HOSE END 4 into sink 4 TEST INSTALLED FAUCET E Operate handle up and down in COLD and HOT positions to flush water lines thoroughly E Connect HAND SPRAY 2 to HOSE END 4 Place HAND SPRAY 2 back into faucet operate HANDLE 1 and check all connections for leaks E Check HAND SPRAY 2 operation E With faucet on push front of BUTTON for a broad cleansing spray CHECK CONNECTIONS FOR LEAKS Reduced flow If the flow should gradually be reduced over a number of months the AERATOR may have debris in it To clean remove AERATOR 1 and rinse with water to remove any debris Turn on faucet to wash any debris out of the faucet ocrew AERATOR 1 back to the spout Operate faucet E Clogged CARTRIDGE outlets or inlets may cause reduced flow To clean first turn off water supply then E Remove BUTTON 2 and loosen HANDLE SCREW 2 and pull off HANDLE 3 m Remove ESCUTCHEON CAP 4 by pulling it upward Unscrew the three CARTRIDGE SCREWS 5 and remove CARTRIDGE 6 Clean inlets of
Download Pdf Manuals
Related Search