American Standard Amarilis Heritage Kitchen Faucet 8281 User's Manual
Contents
1. Amtrican Standard Installation Instructions BOTTOM MOUNTED HERITAGE KITCHEN FAUCETS 7230 SERIES 7231 SERIES 7270 SERIES 7271 SERIES A MARILIS 8280 SERIES 8281 SERIES E Certified to comply with ANSI A112 18 1M U S Patent No 5 819 789 To ensure that your installation proceeds smoothly please read these instructions carefully before you begin SPOUT gt SUBASSEMBLY l 5 AERATOR we ee ESCUTCHEON HANDLE RUBBER SCREW a RING ae Sor amp RUBBER 7230 SERIES gt L WASHER GOOSENECK SPOUT CARTRIDGE lt BRASS WASHER CARTRIDGE S o lt LOCKNUT ESCUTCHEON DIVERTER oe eee RUBBER ane RING CD wasir O _ 2 7270 SERIES See D D TUBE SPOUT LOCKNUT VALVE HOUSING SY W 4 COUPLING NUT NIPPLE HI FLOW SPOUT WRENCH CAUTION Turn off hot and cold water supplies before beginning VALVE INSTALLATION Remove ESCUTCHEONS with RUBBER RINGS and insert VALVE HOUSING through holes from underside of SINK Thread of all three VALVE SHANKS should extend at least 5 16 inch above SINK top If necessary adjust LOCKNUTS Place RUBBER RINGS into ESCUTCHEONS recess and thread ESCUTCHEONS onto VALVE HOUSING until snug against internal stop Center VALVE HOUSING on SINK and tighten LOCKNUTS 3 using WRENCH supplied with faucet Connect the HOT water supply to the left valve and the COLD water supply to the right valve using sealant approp2. o SHANK of SPRAY HOLDER and tighten RUBBER WASHER Feed SPRAY HOSE through SPRAY HOLDER and attach SPRAY COUPLING NUT of HOSE to HOLDER NIPPLE of VALVE CENTER Tighten COUPLING NUT VANE firmly CENTER Make certain that SPACER WASHER and RUBBER WASHER are attached to SPRAY HOSE and thread SPRAY HEAD to NUT SPOUT SUBASSEMBLY O RINGS Operate both handles to flush water lines thoroughly Check spout mounting and hose connections for leaks Turn handles into OFF position and replace AERATOR If spout drips operate handles several times from OFF to ON position Do not force handles turn only 90 Plastic SCREEN in CARTRIDGE may accumulate dirt causing reduced water flow To clean first turn off hot and cold water supplies then Remove INSERT and HANDLE SCREW Slip HANDLE with ADAPTER off Unscrew CARTRIDGE with wrench Thoroughly rinse plastic SCREEN at base of C RTRIDEE Replace CARTRIDGE until flange is tight against valve body Turn valves OFF SCREEN Replace ADAPTER HANDLE SCREW and INSERT CARTRIDGE Product names listed herein are trademarks of American Standard Inc American Standard Inc 1999 M34450B
3. riate connectors and COUPLING NUTS ESCUTCHEON HANDLE eN RUBBER SCREW 5 16 a RING je SINK RUBBER WASHER BRASS WASHER LOCKNUT VALVE BODY N N p Vs SPOUT INSTALLATION Check that both O RINGS are properly seated on the valve center FOR MODELS WITH HAND SPRAY Check that the DIVERTER PLUG is free and can move up and down Apply the grease provided liberally to the O RINGS Push the SPOUT SUBASSEMBLY on to the VALVE CENTER and tighten the SPOUT NUT until snug on valve body TEST INSTALLED FAUCET Remove AERATOR With handle in OFF position turn on water supplies and check all connections for leaks SERVICE To change direction of handle rotation proceed as follows E Turn valve to OFF position m Remove INSERT and HANDLE SCREW SPRING m Slip HANDLE with ADAPTER off CLIP m Remove SPRING CLIP STOP m Lift STOP WASHER turn 90 and replace WASHER m Replace SPRING CLIP m Replace ADAPTER HANDLE SCREW and INSERT AERATOR may accumulate dirt causing distorted and reduced water flow Remove AERATOR and rinse clean HOTLINE FOR HELP For toll free information and answers to your questions call 1 800 223 0068 Weekdays 8 00 a m to 4 00 p m Eastern Time HAND SPRAY INSTALLATION FOR MODEL 7231 AND 7271 ONLY Place SPRAY HOLDER into separate hole of SINK Assemble PLASTIC LOCKNUT ont
Download Pdf Manuals
Related Search