Airlink101 AGSW801 User's Manual
Contents
1. 0Mbps data transmission two pairs Category 3 4 or 5 standards for 10Mbps data transmission Maximum length using UTP cable between the switch and connected device is 100 meters 300ft Once the network cable is connected to both ends and the attached network device is powered on the green LNK ACT LED should be lit Step 2 Connecting the power Connect the output end of the power adapter to the power connector on the rear panel of the switch Connect the power adapter to the power outlet The green Power LED on the front panel should be lit Troubleshooting 1 Power LED is not lit e Check if the power adapter is properly connected to the power outlet Make sure the power jack is firmly plugged into the power socket of the switch 2 Link Activity is not lit when connect to 10 100 1000Mbps device e Check the power switch of the network device attached to the switch make sure it is turned ON e Check the network cable make sure it is properly connected to the switch and the network device e Check the network cable make sure the UTP cables comply with the specifications described in Section 2 Technical Support E mail support airlink101 com Toll Free 1 888 746 3238 Website www airlink101 com Power savings may vary depending on products used Actual data throughput will vary Network conditions and environmental factors lower actual data throughput rate Specifications are subject to change without notice All right2. Abin Quick Installation Guide 8 Port 10 100 1000Mbps Green Switch Model AGSW801 Ver 1A Introduction This Quick Installation Guide tells you how to install your 8 Port 10 100 1000Mbps Green Switch and how to connect it to your Gigabit Ethernet network The 8 Port 10 100 1000Mbps Green Switch is designed for energy saving easy installation and high performance in an environment where network traffic and the number of users increase continuously You can add other Ethernet devices like computers IP cameras and Network Attached Storage NAS onto your network quickly and easily The Green Ethernet technology of AGSW801 automatically reduces the power usage when a connected port is detected inactive idle or cable unplugged and intelligently allocates less power for a port that connects with an Ethernet cable shorter than 20m 66 ft Before you begin the installation please check the items of your package Package Contents e 8 Port 10 100 1000Mbps Green Switch e Power Adapter e Quick Installation Guide Hardware Description Front Panel 1 8 LNK IACT e 8 Port 10 100 1000Mbps Pern e e PWE Green Switch SPEED LED Indicators LED Color Status Description On The switch is powered on PWR Green Off The switch is powered off On LAN port is connected LNK ACT Green Off LAN port is not connected Flashing Transferring or receiving data Yellow On The LAN port is r
3. s reserved Copyright 2009 AirLink101 AirLink101 the stylized AirLink101 logo specific product designations and all other words and logos that are identified as trademarks and or service marks are unless noted otherwise the trademarks and service marks of AirLink101 All other product or service names are the property of their respective holders AirLink101 products are protected under numerous U S and foreign patents and pending applications mask work rights and copyrights
4. unning at 1000Mbps Green lt i lt lt O i is i C SPEED Green On The LAN port is running at 100Mbps Yellow Off The LAN port is running at 10Mbps Rear Panel Power 8 LIC Itt Jt IL JL IL Ports Item Name Description Power Power connector DC 12V 1A 1 8 10 100 1000Mbps LAN ports 1 to 8 Connecting the Switch Note Operating Environment This switch must be installed and operated within the limits of specified operating temperature 32 131 F and humidity 10 90 Non condensing Do not place objects on top of the unit Do not obstruct any vents at the sides of the unit Do not position the unit near any heating source such as heater radiator or direct exposure to sun Prevent entering of water and moisture into the unit If necessary use dehumidifier to reduce humidity Step 1 Connecting to network devices The RJ 45 ports on the switch support Auto MDI MDI X function which allows using straight through or cross over type cables to connect this switch to workstation or hub Connect one end of the network cable to the RJ 45 port on the rear panel and connect the other end of the network cable to the RJ 45 port on the network device Follow the same procedure to connect all the RJ 45 ports of the switch The UTP network cables must be four pairs Category 5 or above for 1000Mbps data transmission two pairs Category 5 for 10
Download Pdf Manuals
Related Search