Accusplit 760M User's Manual
Contents
1. 008 2001 002 2 19 A 10 15 30 The header consisting of the date time stamp will be shown The number of laps in the segment will appear in the upper left while the segment number is displayed in the middle left If the segment shown is not your desired segment press START to reach the desired segment The current segment will be accessed first then it will cycle back to the 1st then 2nd and so on When you have found the segment you want you can press RECALL button consecutively to read the lap records from the first to the last lap RECALL 001 0 01 00 55 002 0 00 12 86 an 0 01 00 55 As you continue to press RECALL during the display of the last lap you can advance to the next segment by pressing START The front page of the segment will be shown Say the next segment is SEG 1 RECALL 012 2001 001 2 18 A 10 00 15 How to delete individual memory segments Search the desired segment first as described above During the display of the segment front page press RESET for 2 seconds to activate Delete One function DELETE ONE will be shown in blinking and beep sound will be generated dELETE OnE A ready period of 2 seconds will be counted At the end of the ready period all the lap records of the corresponding segment will be erased And a long beep sound will be heard Then the displav will show the next segment If you don t want to delete t2. In the Speed mode you can record a number of lap times and speeds for covering the distance you program into the chronograph Before starting to use the Speed mode you need to enter the distance as explained below Otherwise the speed measurement won t work 15 16 Distance Setting Press RECALL for 2 seconds to enter setting mode he unit icon flashes DIST KM 000 000 0 00 00 00 0 00 00 00 000 LAP STOP Press START to toggle between KM and MILE To se digit will blink and you can set the distance from the least significant digit to the most significant digit The distance can be set in the range 0 000 to 1999 999 km or ML Press RECALL OR MODE to exit from the setting mode As an example the distance is set at 400m ect the following digits press RESET The far right DIST KM 0 400 0 00 00 00 0 00 00 00 000 LAP STOP Speed Mode Running Press START to start the Speed timer The STOP indicator is OFF The maximum time can be up to 19 hr 59 min 59 99 sec DIST KM 0 000 0 00 00 00 0 00 05 35 000 LAP RUN While the timer is running press LAP SPLIT to record mph will be displayed on the upper line The lap counter shown on the upper left corner will advance by one the lap time and the corresponding speed in km hr or DIST KM 25 760 0 01 05 35 0 01 05 35 001 LAP RUN P
3. OFF you can press RESET The bell icon will be ON and OFF correspondingiv Normal Time Setting Press and hold RECALL for 2 seconds to enter setting mode The normal time setting starts with second The second digits will then be flashing You can change the flashing digit by pressing START button To speed up the setting you can press and hold START for longer than 2 seconds to activate fast setting To select other digits press RESET button The setting order is Second Minute Hour Year Month Date month date m d or date month d m Sound ON or OFF Contrast and recvcles again Note when the second is to At the end of setting press IRECALLI or IMODI Displav Displav for Sound ON or OFF setting Let the current status be ON SOUnd On darkness of the digits default is 9 then back to Second be set press START to reset the second digits to zero E to exit from the setting mode and back to Normal Time Press START to toggle Sound ON or OFF SOUnd On Display for contrast adjustment Let the current contrast be 5 COnT Press START consecutively to advance the contrast up to 16 then cycle back to 1 The contrast setting will be shown on the display COnT 16 NOTE The hour digits may be displayed in 12hr or The year digits can be set from 2000 to 2099 The date adjusts automa 24hr format ically for odd and even months including
4. 000 hour chronograph by pressing LAP SPLIT again 1 10 000H 000 SPLIT 0 00000 0 00000 STOP 0 00000 1 100000H Please note that if the stopwatch has started running or is running no selection for chronograph operating modes can be made until the stopwatch has been stopped and reset Segmented run memorv for lap split time storage A header consisting of the date time stamp is attached to each segment to indicate the moment when vou began recording the particular timing segment To get to this feature press IMODEJ in chronograph mode to enter DATA mode when the stopwatch has been stopped Records for different segments can be recalled read or deleted Detailed operation in DATA mode is described in Data Mode section below Chronograph Data Recall Mode Press RECALL in Chronograph mode to recall stored split lap time memories The mode message will be shown up for one to two seconds as mode message display is enabled RECALL The split and lap time will be displayed on the upper and the middle line respectively The lower line shows the current stopwatch counting During data recall the fastest lap time will be reviewed first RECALL FAST 004 0 01 12 34 sa O 00 01 60 an 0 03 06 52 Then comes the slowest lap time by further pressing of RECALL RECALL SLOW 001 0 00 07 63 0 00 07 63 LAP an 0 03 10 16 Press RECALL again to v
5. ACCUSPLIT DIGITAL QUARTZ STOPWATCH AE602M100 AE760M100 AE790M500 AE790M500DEC INSTRUCTION MANUAL IMPORTANT NOTE FOR MODEL 760M amp 790M This stopwatch can store up to 100 or 500 split lap times depending on the model However please note when there are 5 free memories left the icon FULL will blink to remind you of the nearly full situation Whenever the storage is full extra split lap times will NOT be stored into memory even though you reset your stopwatch and start a new event Extra split lap times will only be shown on the display but not recorded In order for the stopwatch to record the lap split times again you must delete the data in the DATA memory Please refer to the Data Mode section on the instruction manual for how to delete the memory Instructions Introduction Vou are about to enjov an advanced Cumulative and Lap memorv professional digital quartz stopwatch with advanced timing features Model AE602M100 AE760M100 AE790M500 amp AE790M500DEC Stopwatch includes Time of day Daily Alarm Chronograph stopwatch 100 or 500 memory Data register Model 760M amp 790M only Countdown timer Stroke Measurement timer Pacer from 5 to 240 beats per minute Model AE790M500DEC Decimal Stopwatch includes Decimal stopwatch 1 100 of a sec 1 1000 of a minute 1 100 000 of an hour Model AE760M100 amp AE790M500 Speed Stopwatch includes Speed Measurement General Features 4 buttons o
6. ETI to move to minute 000 0 00 00 0 See CR 0 00 00 0 A 12 58 57 Press RESET further to go to 2 f u hour digits Hour digits can be 000 0 00 00 0 adjusted from 0 to 19 CR A B sai 0 59 02 Press RESET again to adjust the n 1 u operating mode Press START 000 0 00 00 0 to switch the operating modes CR 0 00 00 0 among CR CS and CU A 12 59 11 At the end of setting press RECALL or MODE to leave setting mode 13 14 Pacer Mode Press IMODEJ until vou enter the Pacer mode In the Pacer mode vou can set the standard pacer speed from 5 to 240 beats per minute i n the following values 5 10 20 30 40 50 60 80 100 120 150 180 200 240 In Pacer mode the display will be PACER P 5 The digits are flashing to indicate that the pace co count Once the desired p ace count is selected unt is ready for setting Press RESET to select the pace press START to confirm the setting and start the pace count The display will show the elapsed time on the upper line the pace count number on the middle and the pace count value on the lower display 0 00 51 85 C 0051 P 60 Press STOP to stop the pace count The STOP indicator is ON to show the status and the display freezes To restart the pace count press START again Or press RESET to reset the time elapsed and the pace count number as follows Stroke Measurement Press MODE until
7. February of leap years The day of week also adjusts automatically after you set the date Alarm Time Mode Press IMODEJ until vou enter Alarm mode This mode is used for displaving the dailv alarm time and allows you to enable or disable the alarm When vou enter the Alarm Time mode the displav shows the alarm time on the upper line while the date is shown in the middle of the displav and the normal time is on the lower line AL P 3 30 TU 1 3 A 10 3530 To toggle the alarm ON or OFF press RESET When alarm is ON the indicator 0 will be ON while it will be turned off when alarm is disabled When alarm time is reached the alarm signal will sound for 60 seconds Press anv button to stop the alarm sound Setting Alarm Time Press and hold RECALL for 2 seconds to activate the alarm setting The alarm minute digits will flash as an indication Adjust the flashing digit by pressing START To set the alarm hour digits press RESET to switch to hour digits and then press START to adjust Press RECALL or MODE to exit from Alarm setting mode Chronograph and Recall Mode Press MODE until you enter the Chrono mode The stopwatch can measure up to 19 hours 59 minutes 59 99 seconds When you enter the Chronograph mode the display format is as below 000 0 00 00 00 sm 0 00 00 00 0 00 00 00 The upper line shows the split time the middle line shows the lap time and the accumulated elapsed
8. acer mode Stroke measurement mode Speed mode AE760M100 amp AE790M500 model only Button Operation Mode used to change the mode of the watch Start Stop Set used to start and stop the timer counting or the chronograph function Recall used for recalling recorded split and lap times Lap Split Reset Select for taking the record of the split and lap time TIMER PACER STROKE SPEEd This is only a brief description of these buttons Detailed uses of the buttons are different in particular functions and will be described later in the instructions Pressing MODE button will toggle among the modes above Note that there is no auto return function in the stopwatch Whenever you change modes the stopwatch will remain in that mode until the MODE button is pressed again Each time you enter a mode a message will be displayed for a second before you enter the mode Note In the following descriptions items printed in dark gray stand for flashing digits Normal Time Mode The starting point for operating your stopwatch is NORMAL TIME If NORMAL TIME is not displayed press Mode until it is Year 2001 Date January 1 Day of week Monday Time 12 00 am The display format is as below 2001 year WE 1 3 day month date A10 35 30 hr min second During clock display press START to switch between 12Hr and 24Hr display mode To toggle chime ON or
9. er is located at the upper left of the display Before starting the timer enter a countdown time first Then press ISTARTI to start timer running When the timer counts down to zero a 3 second beep beep sound will be generated for a timer setting within one minute 15 second beep beep sound for 1 minute to 10 minutes setting and 30 second beep beep sound for over 10 minutes Pressing any key will stop the beep sound Under CR operation mode the timer value will be reloaded and count down will start again The timer cycle counter will be increased by one and updated on the display Under CS operation mode the timer after counting down to 0 00 00 will stay at 0 00 00 0 until you press IRESETI to reload the timer value Under CU operation mode the timer after counting down to 0 00 00 0 will count up and stop at 19 59 59 9 How to set the timer Press and hold RECALL for 2 seconds to activate timer setting Timer setting starts with second digits which are shown blinking You can press START to advance the flashing digits Or you can press RESET to select other digits The setting is in sequence of second minute hour and timer operating mode CR CS and CU NOTE You can only set Hour Minute and Seconds The 1 10 second cannot be set Press and hold RECALL for 2 seconds 1 u Timer setting starts with second pesa o je si digits a A 12 58 55 Press RES
10. he records you can press any key to exit from delete ready state before the end of the ready period and resume the display of the segment front page 11 12 How to delete all memorv segments Instead of deleting one segment vou can also delete all memorv segments When vou enter the Data mode you see the screen FREE XXX LAP Press and hold the RESET for 3 seconds You will hear Beep beep beep for 3 seconds then a long Beep At this point all data in the memory will be deleted and DELETE ALL will show on the display If you don t want to delete the records you can press any key to exit DELETE ALL state before the end of the ready period and resume the display of the segment front page dELETE ALL Timer Mode Press MODE until you enter the Timer mode 3 count down operation modes are available on this stopwatch Count down repeat CR Count down stop CS Count down then count up CU The timer is set at the factory to the count down repeat CR mode At entering timer mode the mode message TIMER will be shown for a second before the timer counting is to be displayed 000 0 00 00 0 CR 0 00 00 0 A 12 58 20 The upper line shows the programmable timer value initially set at 0 00 00 0 while the middle line displays the current timer counting Time of Dav clock displav is at the lower line of the displav CR indicates the current timer operating mode while the timer cycle count
11. iew the average lap time Press IRECALLI continuall to the first record when the RECALL RECALL RECALL RECALL 005 AVG 0 00 05 12 0 03 16 03 LAP RUN ly to review all the stored spi stopwatch is running and vi it lap times The sequence starts from the last record ice versa when the stopwatch has been stopped RECALL 005 0 00 14 91 9 00 02 05 an 0 03 28 94 004 0 00 12 86 sv 0 00 01 60 an 0 03 33 64 003 0 00 11 26 sv 0 00 01 78 an 0 03 40 15 002 0 00 09 48 9 00 01 85 an 0 03 45 34 10 RECALL After recalling the first record press RECALL once mor mode The RECALL ico RECALL RECALL 001 SPLIT 0 00 07 63 0 00 07 63 0 03 48 01 LAP RUN n will be OFF e to exit from Recall mode and go back to chronograph 0 03 50 11 0 00 42 60 0 03 50 11 005 During memory recall you can press either START STOP or LAP SPLIT to exit from chrono recall mode and jump to the chrono start stop or lap state respectively Data Mode AE760M amp AE790M Model only Press MODE until you en before the number of free memories is to be shown You can press START to scroll through all segments jer DATA mode The mode message DATA will be shown for one to two seconds FREE 95 LAP The current segment will come first RECALL
12. n Whenever the storage is full extra split lap times will not be stored into memory but will still be shown on the display Any fastest and slowest laps will not be stored The memory counter will flash as the extra split lap times are being displayed The icon FULL will be steadily ON The maximum memory counter value is 100 or 500 To stop the chronograph press STOP The indicator STOP will come on again to show the status Press RESET as the stopwatch stops to reset the stopwatch while the split lap times will be kept in memory When the stopwatch starts running from reset state all the lap memories will be cleared Decimal Timing AE790M 1 ISOODEC model only second and decimal hour chronograph As you press MODE to enter the chronograph mode shown Reset the chronograph to 00 then press LAP SPLIT will note the change by lool Change to the 1 1000 of a 000 SPLIT 0 00 00 00 0 00 00 00 0 00 00 00 LAP STOP king at the bottom of the dis 000 00000 00 00000 00 00000 00 soos LAP STOP 000 SPLIT 000 000 000 000 000 000 1 1000M STOP The DM Model can operate as a normal 1 100 second chronograph as well as decimal minute decimal he normal 1 100 second chronograph displav will be o go to the second chronograph mode 1 100s You plav to see 1 100s minute chronograph mode by pressing LAP SPLIT again 1 1000M Go to the 1 10
13. ower line shows the current time counting During Data recall the fastest speed will be reviewed first then the slowest speed and average speed Further presses of RECALL will retrieve the memories in ascending order or reverse order depending on whether the speed measurement is stopped or under operation respectively During Recall the Recall indicator is ON Note Speed mode and Chrono mode will not run simultaneously When Chrono mode is active Speed mode should be in reset state and vice versa ALCLCUSPLIT NO PROOF OF PURCHASE LIMITED WARRANTY See label on back of unit for details or check http support ACCUSPLIT com ACCUSPLIT Inc 3090 Independence Drive Suite 148 Livermore CA 94551 USA 800 935 1996 e 925 290 1900 9 FAX 925 290 1930 www ACCUSPLIT com 7 support ACCUSPLIT com
14. peration Large LCD display with contrast adjustment 12 24 hour display Normal time and chime Daily alarm Full 1 100 second chronograph with working range from 0 to 19 hr 59 min 59 99 seconds with 100 or 500 memory records of split and lap time Recall function for recorded split and lap times Count Down timer with working range from 0 to 19hr 59min 59 9 seconds Three operating modes Countdown Repeat Countdown Stop Countdown then count up for count down timer Stroke measurement basing on 3 Speed measurement AE760M100 amp AE790M500 Model only Decimal second minute and hour chronograph AE790M500DEC Model only Segmented run memory Model 760M 8 790M only Beep sound selectable Low battery check As you choose each mode a message will be displayed for a second before you enter the mode Normal Time mode All models TIME Alarm Time mode All models ALARM Chronograph mode All models CHRONO Lap Time Recall mode All models RECALL Data mode DATA 760M amp 790M models only Timer mode All models Pacer mode All models Stroke Measurement All models Speed mode AE760M100 amp AE790M500 model only The operation of the stopwatch is divided into eight modes as noted above AN OA PON gt Normal time mode Alarm time mode Chronograph and Recall mode Data mode 760M amp 790M Models only Count down timer mode P
15. ress LAP SPLIT to record more lap times and show different speeds Note that as the speed exceeds the value 1999 999 km hr or 1999 999 mph Err will be shown and no storage will be made for that record LAP SPLIT LAP SPLIT 002 LAP RUN DIST KM 22 060 0 01 05 25 0 02 01 15 003 LAP RUN DIST KM 25 730 0 00 55 95 0 02 57 10 To stop the speed measurement press STOP to stop the timer 003 LAP STOP DIST KM 25 730 0 00 59 13 0 03 48 23 Before starting again you can reset the timer by press ing RESET 000 LAP STOP DIST KM 0 400 0 00 00 00 0 00 00 00 Note When you reset the Speed timer the speed measurement starts again from a reset state and all speed records in memory will be cleared provided that the storage is not under segmented run memory mode The Recall function is simi can be accessed and records storing both the speed and elapsed time can be retrieved jar to chronograph recall If segmented run memory is selected the DATA mode 17 18 Lap Time amp Speed Recall Similar to the Chrono Recall mode during speed measurement or Stop state you can press RECALL to recall the speed lap memories The Mode message will be shown for one to two seconds as the Mode message display is displayed RECALL The Speed and Lap time will be displayed on the upper and the middle lines The l
16. time is displayed on the lower line Whenever the stopwatch si start the stopwatch As it r 000 0 00 00 00 0 00 00 00 0 03 35 52 ops running the STOP indicator will be ON Press the button START STOP to uns the current elapsed time is shown on the lower line To view the current split lap time you can press LAP SPLIT 001 0 10 43 35 0 10 43 35 0 10 43 35 The number of split lap times is shown on the upper left corner The corresponding split and lap times are displayed on the upper and middle line Press LAP S the number of split lap time is updated 002 SPLIT RUN 0 15 10 94 0 04 27 59 0 15 10 94 PLIT again the next split lap time will be shown and The stopwatch Model 790M amp 790MDEC can store up to 500 split lap times The split lap times can be stored into the memory as you press LAP SPLIT to view the current split lap time Meanwhile the lap and split time will be frozen for 5 seconds After this 5 second period the lap and split time will return to normal In addition the fastest lap the slowest lap and the averages of all laps will also be recorded As you press STOP to stop the chronograph the last lap split time will also be stored provided that the last lap split time is not the first lap split time When there are 5 free memories left the icon FULL will blink to remind you of the nearly full situatio
17. you en 0 00 00 00 C 00 00 P 60 er the Stroke Measure ment mode The display will be as follows STROKE 0 0 In the Stroke Measurement mode the duration of 3 strokes is taken and the stroke frequencv counts per minute is calculated As the stroke frequency falls out of the range of 10 180 Err will appear to show the error condition Press START to start the measurement During the 1st second 180 0 will be shown and flashing as below STROKE 180 0 At the end of the first second the display will become steady If measurement is stopped in the first second stroke frequency gt 180 error signal Err will be shown After the first second has elapsed the instantaneous measurement reading will be shown When you press STOP the display will show the steady stroke measurement reading If the measurement lasts for more than 18 seconds stroke frequency lt 10 an error signal Err will be displayed When the measurement is stopped press RESET to reset the displayed reading to 0 0 Speed Mode AE760M100 amp AE790M500 Model only Press MODE until you enter the Speed mode The display will be as follows DIST KM 000 0 000 ue 0 00 00 00 sop 0 00 00 00 Note that the default setting is KM Hence KM icon will be ON The upper line shows the distance or speed The lap time is in the middle line while the total time is displayed on the lower line
Download Pdf Manuals
Related Search