Elite Screens R273WV1 Plus
Contents
1. ezFrame Plus Series Fixed Frame Projection Screen Hardware and Parts List User s Guide 1 Frame Parts x 6 pcs 4 top bottom horizontal frame pcs 2 side vertical frame pcs 2 Tension Rods x 6 pcs 4 top bottom rods 2 side rods 3 Screen Material x l pe 4 Center joints x 2 pcs 5 Elbow Joints x 4 pcs 6 Wall brackets x 2 3 pcs depending on model size 7 M5x50 wood screws x 6 pcs 8 Hollow wall anchor x 6 pcs 9 M5x15 screws x 16 pcs 10 Center Support Bar x 1 2 pcs depending on model size 11 Support joiner x 2 4 pcs depending on model size 12 Fix Plates x 60 180 pcs depending on model size Note Please make sure all parts are included in your package before proceeding to assemble your Elite Screens fixed frame projection screen FRAME ASSEMBLY 1 Insert the center joint connector into to one of the 1 2 horizontal frames and fasten it with two M5x15 screws M5 X 15 screws Horizontal Frame Push _ a Joint j Rev 041014 JA www elitescreens com 1 2 Insert the other 1 2 horizontal frame piece to the center joint connector and fasten it with two M5x15 screws Repeat steps 1 and 2 for assembling the second horizontal frame Horizontal Long Frame Note a 2 long frames should be assembled for a screen b Do not tighten the screws completely until all frame pieces have been assembled correctly 3 Insert both elbow joint connectors into the long hor2. Black backing for AcousticPro models This procedure only applies to AcousticPro models Disregard this section if your Fixed Frame does not include an acoustically transparent screen material The purpose of the black backing material is to block out any light penetration that may reflect off of anything mounted behind the screen which can cause distortion to the projected image The black backing is held in place by the Velcro that is on the fix plates Black backing Fix plates secure the Acoustic material and the black backing behind it erect Interval markings reveal the best points for inserting the fix plates hA AOAO NDA i Fig 13 The prongs on the fix plates insert to the lip on the back EE V E RTR Ron a of the frame creating a friction hold that will firmly keep the fe NR ISA ARAR material and black backing in place Fig 14 15 After the l 3 inners i hy A material has been installed the backing will lie over the back of I EERE Oe RR Oa MN the white Acoustic material and then be held in place by the aa we ay Velcro on the fix plates Fig 16 Fig 13 Fig 14 Fig 15 Fig 16 Rev 041014 JA www elitescreens com 5 Center Support Bar 1 Insert the support joiner into each end of the center support bar to complete assembly support joiner NS li Center support bar h 2 Insert the Center Support Bar into the upper top groove on the back of the frame not the one where the f
3. accordance with household safety guidelines For a local Elite Screens contact or Technical Support please visit www elitescreens com Rev 041014 JA www elitescreens com 7
4. ix plate inserts with the bottom end near the approximate center point as shown in Fig 17 and rotate it in at an angle so that both ends of the bar are in alignment with the groove Center point 1 Wa a Remove Push Center point Fig 17 Center Support Bar L 3 Slide the top end of the bar into the top center point of the frame to complete the center support bar installation This will provide added stability to your frame and added tension to the material Installation 1 Locate your desired installation location with a stud finder recommended and mark the drill hole area of where the screen is to be installed Drill a hole with the proper bit size according to the wood screws included 3 Line up the wall brackets with the drilled holes on the installation location and screw them in using a Phillips screwdriver Note Use use 3 top wall brackets on diagonal sizes 135 and above 4 Position the fixed frame screen onto the top wall brackets as shown in Fig 19 and push down at the center of the bottom frame to secure the installation 5 The design of the wall brackets allows the frame to slide over them through its sides This is an important feature of the installation design as it allows your screen to be properly centered 6 Using both hands finish the installation by pushing the lower portion of the fixed frame screen into the lower b
5. izontal frame and then fasten it with two M5x15 screws see Fig 1 Then insert the vertical short frames and fasten them with screws fig 1 2 _ Long frame Short frame Short frame Fig 1 1 d M5 X 15 screws Fig 1 2 Rev 041014 JA www elitescreens com 2 4 Join all four frame parts together following the steps shown below Fig 2 Note When assembled please push simultaneously the two ends of the long frames Insert the exposed ends of the joint connectors into the short vertical frame and align the four corners so that they meet at perfect right angles Wy E M fig 2 Attaching the screen material to the frame 1 Unroll the screen material and lay it down on a clean surface edges of all four corners of the material see fig 3 Then insert the tension rods separately into the Tension Rod Vertical x 2 Tension Rod Horizontal x 4 push Tension Rod Vertical x 2 ee Tension Rod Horizontal x 4 Screen Material Screen Material P Fig 3 gt aoo push push Rev 041014 JA www elitescreens com 2 Make sure that the material and fra
6. me are both lying face down on a clean dry and non abrasive surface 3 Center the material inside the frame Please note the material will be noticeably smaller than the frame as the material must be stretched to create a sufficient amount of tension for perfect material flatness 4 Attach the fix plates 1 Begin by securing the four corners in the following order A gt B gt C gt D Fig 4 2 Insert the fix plates as shown on Fig 5 Fix plate is approximately 10 cm away from the frame s corner and fix plate is approximately 5cm away Fig 4 3 Stretch the material to the corner and insert the screen material s edge into the groove of the frame While one hand holds the material in place the other hand snaps in the push plate Fig 6 Fig 7 Insert push plate in Ni ee 4 Schematic Cross section of the Frame 4 Place a fix plate in the center of each side in the following order E gt F gt G gt H Fig 8 E F u Mx F Fig 8 Rev 041014 JA www elitescreens com 4 5 Put the next set of fix plates 2 in the middle between fix plate 1 and the corner Fig 9 6 Then put the next set of fix plates 3 between 1 and 2 and the corner Fig 10 7 Lastly put the next set of fix plates 4 as shown in Fig 11 8 Repeat steps 5 7 to for the rest of the sides to complete attaching the screen material Fig 12 Fig 12
7. racket as shown in Fig 20 Rev 041014 JA www elitescreens com 6 AYE Tii iii HE be A A i l Please follow these instructions carefully to ensure proper maintenance and safety of your Fixed Frame Screen 1 When hanging the screen up please make sure that no other objects such as power switches outlets furniture ladders windows etc occupy the space designated for your Fixed Frame screen 2 Regardless if the screen is hung on or installed into the wall make sure that the proper mounting anchors are used and that the weight is supported appropriately by a strong and structurally sound surface just as any large and heavy picture frame should Please consult a home improvement specialist for the best advice on installation 3 Frame parts are made of high quality velour surfaced aluminum and should be handled with care 4 When not in use cover over the screen with a furniture sheet to protect it from dirt grime paint or any other impurities 5 When cleaning use a damp soft cloth with warm water to remove any marks on the frame or screen surface 6 Never attempt to use any solutions chemicals or abrasive cleaners on the screen surface 7 In order to avoid damaging the screen avoid touching it directly with your fingers tools or any other sharp or abrasive objects 8 Spare Parts should be placed out of reach of small children in
Download Pdf Manuals
Related Search