Adtran 1442981G1 network transceiver module
Contents
1. This product is designed to meet the following environmental classes e ETSI EN 300 019 1 1 Classification of environmental conditions Storage Class 1 2 e ETSI EN 300 019 1 2 Classification of environmental conditions Transportation Class 2 3 e ETSI EN 300 019 1 3 Classification of environmental conditions Stationary use at weatherprotected locations Class 3 3 The equipment is designed to function without degradation during exposure to all test severities per Class 3 3 of ETSI EN 300 019 1 3 This product meets EU RoHS Directive 2002 95 EC and or applicable exemptions Refer to www adtran com for further information on RoHS WEEE 6144298XGX 22B ADIRAN FRANCAIS Lisez tous les avertissements et mises en garde avant l installation de cet amp quipement ou la r alisation de toute op ration de maintenance Ce produit utilise un module laser de classe 1 qui conforme aux normes 21 CFR 1040 10 1040 11 et IEC 60825 1 et 2 Pour assurer la conformit aux normes mentionn es plus haut seuls les modules laser de classe 1 qui sont approuv s par ADTRAN doit tre utilis dans ce produit Pour une liste des SFP et XFP approuv s par ADTRAN voir adtran com gt support gt support community gt recherche SFP XFP ADTRAN ne peut certifier l int grit d un syst me dot d autres modules laser L ESD d charge lectrostatique peut endommager les modules lectroniques Lors de la manipulation des modules portez un bra2. Optical Path Penalty 2 dB e Receive Sensitivity 24 dBm 9 95 Gbps 10e 12 BER 28 dBm 10 7 Gbps 10e 4 BER 27 dBm 11 1 Gbps 10e 4 BER 26 5 dBm 11 35 Gbps 10e 4 BER e OSNR Dispersion 360 to 1440 ps nm 25 5 dB 9 95 Gbps 10e 12BER 20 dB 10 7 Gbps 10e 4BER 20 dB 11 1 Gbps 10e 4BER 21 dB 11 35 Gbps 10e 4BER e Minimum Span Attenuation 10 dB e Optical Budget 21 dB 9 95 Gbps 10e 12BER 25 dB 10 7 Gbps 10e 4BER 24 dB 11 1 Gbps 10e 4BER 23 5 dB 11 35 Gbps 10e 4BER e Dispersion Tolerance 360 to 1440 ps nm e Optical connectors LC e Extended Environmental Support Operational temperature range 40 C to 65 C Storage temperature range 40 C to 85 C Relative humidity up to 85 noncondensing INSTALLATION To install the LR 2 XFP into an appropriate module complete the following steps 1 Inspect the LR 2 XFP If damaged file a claim with the car rier and then contact ADTRAN Customer Support Do not remove the protective end cap from the XFP until the fiber optic cable is ready to be connected 2 Insert the LR 2 XFP into the XFP cage on the module Ensure that the manufacturer label on the XFP is facing upward for correct installation 3 Slide the LR 2 XFP all the way into the receptacle until there is an audible click NOTE Use the latch on the LR 2 XFP to remove the XFP from the XFP cage mounted on the printed circuit board SAFETY AND REGULAT
3. contained ina Channel 29 1554 13 nm 1442981G9 BVL3AUDD__ single module These XFPs support operations over a wide Channel 30 1553 33 nm 1442982G1 BVL3AUED _ temperature igo and as ine for A in no cs Channel 31 1552 52 nm 1442982C2 EVL3AUFD _ environments They provide a high spee seria at 10 Gbps to Channel 32 1551 72m 144208963 EVL3AUCD _ support SONET SDH Ethernet OTN and Fiber Channel The F gt Channel 33 1550 92 nm 1442982G4 BVL3AUHD__ LR 2 XFP operates on various optical channels Installed in the i appropriate host module the LR 2 XFP provides a 10 Gigabit Slane 1530 12 mi a BVBAUJD interface to the supporting system Channel 35 1549 32 nm 1442982G6 BVL3AUKD__ te 5 R Channel 36 1548 51 1442982G7 BVL3AULD__ The transmit side of the LR 2 XFP converts serial NRZ electrical rm p 5 Channel 37 1547 72 nm 1442983G3 BVL3AUSD__ data at the 10 Gbps line rate to a standard compliant optical and signal The receive side converts the incoming DC balanced serial came 134o azami eS VESTE NRZ optical data at the 10 Gb s line rate into serial electrical data _Channel 39 neo ieee BVISADUD _ r Channel 40 1545 32 nm 1442983G6 BVL3AUVD__ Refer to the table in the next column for the part numbers Channel 41 1544 53 nm 1442983G7 BVL3AUWD__ channels and wave lengths supported by these XFPs Channel 42 1543 73 nm 1442983G8 BVL3AUXD__ NOTE Channel 43 1542 94 nm 1442983G9 BVL3AUYD__ To ensure compatibility refer to the documentation provided Channel 44 154
4. does not meet its published specifications or fails while in service Warranty information can be found online at www adtran com warranty 2012 ADTRAN Inc All Rights Reserved Dieses Produkt erf llt die EU RoHS Richtlinie 2002 95 EC und oder g ltige Ausnahmen Bitte besuchen Sie www adtran com f r ausf hrlichere Informationen zu ROHS WEEE ADTRAN CUSTOMER CARE From within the U S 1 800 726 8663 From outside the U S 1 256 963 8716 PRICING AND AVAILABILITY 1 800 827 0807 6144298X GX 2Bk 2 hs CAUTION SUBJECT TO ELECTROSTATIC DAMAGE OR DECREASE IN RELIABILITY HANDLING PRECAUTIONS REQUIRED
5. 19 1 3 Classification des conditions d environnements l utilisation poste fixe dans des endroits prot g s contre les intemp ries classe 3 3 L quipement est con u pour fonctionner sans d gradation lors des tests tous les niveaux de s v rit suivant les sp cifications de la classe 3 3 de l ETSI EN 300 019 1 3 Ce produit est conforme la directive europ enne RoHS 2002 95 CE et ou aux exon rations applicables Reportez vous a www adtran com pour de plus amples renseignements sur RoHS WEEE DEUTSCH Lesen Sie sich alle Warn und Sicherheitshinweise durch bevor Sie dieses Ger t installieren oder warten Dieses Produkt nutzt ein mit den Richtlinien 21 CFR 1040 10 und 1040 11 und IEC 60825 1 und 2 konformes Class 1 Lasermodul Damit die obigen Richtlinien auch in Zukunft eingehalten werden k nnen installieren Sie nur Klasse 1 Laser Module in diesem Produkt das von ADTRAN zugelassen sind F r eine Liste der ADTRAN SFPs und XFPs siehe adtran com gt Support gt Community gt Suche SFP XFP ADTRAN garantiert nicht f r die Systemintegrit t bei anderen Lasermodulen Elektrostatische Entladung k nnen elektronische Module besch digen Tragen Sie beim Umgang mit Modulen ein Erdungsarmband um Sch den an den elektronischen Komponenten zu vermeiden Transportieren oder lagern Sie Module in antistatischem Verpackungsmaterial Bei der Arbeit an den Modulen achten Sie darauf diese stets auf antistatische elektrisch ge
6. 2 14 nm 1442986G1 BVL3AUZD__ with the host module Channel 45 1541 35 nm 1442986G2 BVL3AUOD__ The foll ino f d he LR 2 XFP Channel 46 1540 56 nm 1442986G3 BVL3AU1ID__ e tollowing features are supported on the LR i Channel 47 153977nm 1442986G4 BVL3AU2D__ e Optical signals for up to 80 km reach Channel 48 1538 98 nm 1442986G5 BVL3AU3D__ e Low power consumption lt 3 5 W max Channel 49 1538 19 nm 1442986G6 BVL3AU4D__ Channel 50 1537 40 nm 1442986G7 BVL3AU5D_ _ A CAUTION anne Bi 153661nm 1442986G8___ BVL3AU6D__ Due to compliance certification requirements use only XFPs Channel 52 1535 82 nm 1442986G9 BVL3AU7D__ supplied by ADTRAN with the host module ADTRAN cannot Channel 53 1535 04 nm 1442987G1 BVL3AUSD__ certify system integrity with other XFPs Channel 54 1534 25 nm 1442987G2 BVL3AU9D__ Channel 55 1533 47 nm 1442987G3 BVL3AVAD__ Channel 56 1532 68 nm 1442987G4 BVL3AVBD__ Channel 57 1531 90 nm 1442987G5 BVL3AVCD__ Channel 58 1531 12 nm 1442987G6 BVL3AVDD__ Channel 59 1530 33 nm 1442987G7 BVL3AVED__ Channel 60 1529 55 nm 1442987G8 BVL3AVFD__ ADIRAN OPERATIONAL SPECIFICATIONS e Channel Spacing 100 GHz e Data Rate 9 95 Gbps to 11 35 Gbps e Optical distance 80 km maximum e Transmit Wavelength See Supported Modules Table e Receive Wavelength 1270 to 1600 nm e Optical transmit levels 1 0 to 3 0 dBm e Spectral width 1 nm e Extinction Ratio 8 2 dB e Max Optical receive level 7 0 dBm e Receiver Damage Threshold 7 0 dBm e
7. ADRAN Small Form Factor Pluggable jobAid 10 Gbps LR 2 DWDM 80 km Issue Date December 2012 Product P N 144298XGX Document P N 6144298XGX 22B Documentation for ADTRAN Carrier Networks products is The following document provides additional information for this product available for viewing and download directly from the Broadband SFP XFP Matrix Application Guide P N 61442000G1 49 ADTRAN Support Community website Go to adtran com gt support gt support community Registration is required SUPPORTED MODULES This Job Aid supports the modules listed in the following table Channel Number Wave Length Part Number CLEI Channel 17 1563 86 nm 1442982G8 BVL3AUMD__ Channel 18 1563 05 nm 1442982G9 BVL3AUND__ Channel 19 1562 23 nm 1442983G1 BVL3AUPD__ Channel 20 1561 42 nm 1442983G2 BVL3AURD__ Channel 21 1560 61 nm 1442981G1 BVL3AT5D__ Channel 22 1559 79 nm 1442981G2 BVL3AT6D__ Channel 23 1558 98 nm 1442981G3 BVL3AT7D__ Channel 24 1558 17 nm 1442981G4 BVL3AT8D__ Channel 25 1557 36 nm 1442981G5 BVL3AT9ID DESCRIPTION Channel 26 1556 55 nm 1442981G6 BVL3AUAD__ The Small Form Factor Pluggable Long Reach 10 Gbps LR 2 Channel 27 1555 75 nm 1442981G7 BVL3AUBD__ DWDM 80 km XFP is a full duplex serial electric serial optic Channel 28 1554 94 nm 1442981G8 BVL3AUCD__ device with both transmit and receive functions
8. ORY COMPLIANCE Read all warnings and cautions before installing or servicing this equipment a SSS This product uses a Class 1 Laser module that complies with 21 CFR 1040 10 and 1040 11 and IEC 60825 1 and 2 For continued compliance with the above standards install only ADTRAN approved Class 1 Laser Modules in this product For a list of ADTRAN approved SFPs and XFPs see adtran com gt support gt support community gt search SFP XFP ADTRAN cannot certify system integrity with other laser modules CA CAUTION e Electrostatic Discharge ESD can damage electronic modules When handling modules wear an antistatic discharge wrist strap to prevent damage to electronic components Place modules in antistatic packing material when transporting or storing When working on modules always place them on an approved antistatic mat that is electrically grounded e Per GR 1089 CORE this product is designed and intended for installation as part of a Common Bonding Network CBN This product is not designed nor intended for installation as part of an Isolated Bonding Network IBN e Per GR 1089 CORE Section 9 this product does not have an internal DC connection between 48 VR and frame ground This product can be installed in a DC I isolated or DC C common installation For installations where other cards or the host system have internal connections between 48 VR and frame ground the system would be intended for deployment only in a DC C i
9. celet de d charge antistatique pour viter d endommager les composants lectroniques Placez les modules dans un emballage antistatique lors du transport ou du stockage Lorsque vous travaillez sur les modules placez les toujours sur un tapis antistatique certifi muni d un branchement de mise la terre Selon le document GR 1089 CORE ce syst me est con u et pr vu pour une installation int gr e un r seau de masse maill Ce syst me n est pas con u ni pr vu pour une installation int gr e un r seau de masse isol IBN Toujours selon la GR 1089 CORE article 9 ce produit n a pas de connexion CC interne entre 48 VR et la masse du ch ssis Ce produit peut tre install en mode CC I isol ou DC C commun Pour les installations quip es d autres cartes ou d un syst me h te ayant des connexions internes entre 48 VR et la masse du ch ssis le syst me doit tre d ploy uniquement dans une installation CC C La borne de mise la terre du ch ssis doit tre branch e une prise de terre afin d assurer que le bo tier m tallique de la SFP XFP est correctement mis la terre gr ce au connecteur de face arri re Ce produit est con u pour r pondre aux classes environnementa les suivantes e ETSI EN 300 019 1 1 Classification des conditions d environnement Entreposage classe 1 2 e ETSI EN 300 019 1 2 Classification des conditions d environnements Transport classe 2 3 e ETSI EN 300 0
10. erdete Matten zu legen Laut GR 1089 CORE dient dieses System zur Installation in einer gemeinsamen Potentialausgleichsanlage Dieses System dient nicht zur Installation in einer isolierten Potentialausgleichsanlage e Gem f s GR 1089 CORE Abschnitt 9 besitzt dieses Produktkeine interne DC Verbindung zwischen 48 VR und der Geh usemasse Dieses Produkt kann in einer DC I Anlage isoliert oder DC C Anlage gemeinsam installiert werden Im Falle von Installationen bei denen andere Karten oder das Hostsystem interne Verbindungen zwischen 48 VR und der Geh usemasse besitzen eignet sich das System ausschlie lich zum Einsatz in einer DC C Installation Die Erdungsschiene des Rahmens muss an eine Bodenstation angeschlossen werden um sicherzustellen dass das Metallgeh use des SFP XFP vorschriftsm ig ber den R ckwandanschluss geerdet ist Dieses Produkt wurde entsprechend der folgenden Umweltklassen ent wickelt e ETSI EN 300 019 1 1 Klassifikation von Umweltbedingungen Lagerung Klasse 1 2 e ETSI EN 300 019 1 2 Klassifikation von Umweltbedingungen Transport Klasse 2 3 e ETSI EN 300 019 1 3 Klassifikation von Umweltbedingungen Station rer Einsatz ohne Witterungseinfl sse Klasse 3 3 Dieses Ger t funktioniert ohne Leistungsabfall w hrend aller f r Klasse 3 3 von ETSI EN 300 019 1 3 vorgeschriebenen Belastung stests a Warranty ADTRAN will replace or repair this product within the warranty period if it
11. nstallation e The chassis frame ground terminal must be connected to an earth ground to ensure that the metal enclosure of the SFP XFP is properly grounded via the backplane connector 6144298XGX 22B NOTE The Gigabit Ethernet port s are optical and therefore are not classified as any type of port as defined in Appendix B of GR 1089 CORE This product is compliant with SFF 8472 Digital Diagnostics Monitoring Interface for Optical Transceivers Revision 9 3 This product is compliant with the XFP Multi Source Agreement MSA This product is designed to be deployed in GR 3108 CORE environmental Class 1 and 2 as defined in GR 3108 CORE This product meets or exceeds all the applicable requirements of NEBS Telcordia GR 63 CORE GR 1089 CORE and ETSI EN 300368 This product is intended for deployment in Central Office type facilities EEEs EECs and locations where the NEC applies for example Customer Premises This product is to be installed in ADTRAN products in Restricted Access Locations only and installed by trained service personnel This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Changes or modifications not expressly approved by ADTRAN could void the user s authority to operate this equipment
Download Pdf Manuals
Related Search