Home

Cisco C3850-NM-2-10G network switch module

image

Contents

1. 5 C to 55 C up to 6000 feet 1800m 5 C to 50 C up to 10 000 feet 3000m 5 C to 45 C up to 13 000 feet 4000m 5 C to 45 C at sealevel with single fan failure Not more than following in one year period 96 consecutive hours or 360 hours total or 15 occurrences 10 to 95 noncondensing With AC or DC power supply with 24 PoE ports loaded LpA 43GB typical 45dB maximum LwA 5 2B typical 5 5B maximum Typical Noise emission for a typical configuration Maximum Statistical maximum to account for variation in production Temperature 40 C to 70 C Altitude 15 000 ft Operating 0 41Grms from 3 to 500Hz with spectral break points of 0 0005 G2 Hz at 10Hz and 200Hz 5dB octave roll off at each end Non operating 1 12Grms from 3 to 500Hz with spectral break points of 0 0065 G2 Hz at 10Hz and 100Hz 5dB octave roll off at each end Operating 30G 2ms half sine Non operating 55G 10ms trapezoid 2013 Cisco and or its affiliates This document is Cisco Public Information Page 19 of 28 Connectors for Cisco Catalyst 3850 Series Table 9 shows connectors Table 9 Connectors Connectors and cabling Power connectors 1000BASE T ports RJ 45 connectors 4 pair Cat 5E UTP cabling 1000BASE T SFP based ports RJ 45 connectors 4 pair Cat 5E UTP cabling e 100BASE FX 1000BASE SX LX LH ZX BX10 DWDM and CWDM SFP transceivers LC fiber connectors single mode or multimode fiber e 10GB
2. CAB TA NA AC power cord for Cisco Catalyst 3850 North America CAB TA AP AC power cord for Cisco Catalyst 3850 Australia CAB TA AR AC power cord for Cisco Catalyst 3850 Argentina CAB TA SW AC power cord for Cisco Catalyst 3850 Switzerland CAB TA UK AC power cord for Cisco Catalyst 3850 United Kingdom CAB TA JP AC power cord for Cisco Catalyst 3850 Japan CAB TA 250VAC JP Japan 250VAC power cord for Cisco Catalyst 3850 Japan CAB TA EU AC power cord for Cisco Catalyst 3850 Europe CAB TA IT AC power cord for Cisco Catalyst 3850 Italy CAB TA IN AC power cord for Cisco Catalyst 3850 India CAB TA CN AC power cord for Cisco Catalyst 3850 China CAB TA DN AC power cord for Cisco Catalyst 3850 Denmark CAB TA IS AC power cord for Cisco Catalyst 3850 Israel CAB C15 CBN Cabinet jumper power cord 250 VAC 13A C14 C15 connectors Spare Accessory and Rack Mount Kits for the Cisco Catalyst 3850 Series C3850 ACC KIT C3850 RAC KIT C3850 4PT KIT Accessory kit for Cisco Catalyst 3850 Series Rack mount kit for Cisco Catalyst 3850 Series Extension rails and brackets for four point mounting for Cisco Catalyst 3850 Series Optics Compatibility Information The Cisco Catalyst 3850 Series supports a wide range of optics Because the list of supported optics is updated on a regular basis consult the tables available here for the latest SFP compatibility information http www cisco com en US products hw modules ps5455 produc
3. presence and conferencing and supports all Cisco Unified Communications wireless IP phones for cost effective real time voice service Deployment Options Campus In a campus type deployment operating the Cisco Catalyst 3850 in the mobility agent mode and centralizing the mobility controller functionality in a WLC 5760 WLC 5508 or WiSMe helps achieve better scalability and performance The Cisco Catalyst 3850 provides CAPWAP termination for access points uniform policy enforcement for wireless clients better wireless bandwidth and uniform Cisco IOS Software based configuration and monitoring for wired plus wireless features The mobility controller provides central mobility RRM and CleanAir coordination Backward compatibility with traditional centralized wireless deployment mode on the WLC 5508 WiSM2 and WLC 5760 ensures that customers can migrate to the Cisco Catalyst 3850 based converged access approach in phases providing a continued controller for existing access points This migration also provides investment protection on the existing wireless controller infrastructure A phased adoption of the new Cisco Catalyst 3850 ensures that migration to the converged access mode of wireless is seamless Figure 6 shows Catalyst 3850 in the campus type deployment 2013 Cisco and or its affiliates This document is Cisco Public Information Page 15 of 28 Figure 6 Mobility Controller MC and Mobility Agent MA New WLC 5760
4. AP CAPWAP Tunnels Mobility Tunnels Branch 3850 is optimized for branch deployments when it operates in mobility controller mode In this mode not only can the switch terminate CAPWAP tunnels from the access points and provide client connectivity it can also manage mobility within the branch This eliminates the need for a local controller in every branch in addition to the access layer switches Also complete visibility into the wired plus wireless traffic means that the WAN router can prioritize the right wired plus wireless traffic in and out of the branch Figure 7 shows Cisco Catalyst 3850 in the branch type deployment 2013 Cisco and or its affiliates This document is Cisco Public Information Page 16 of 28 Figure 7 Deploying Cisco Catalyst 3850 in the Branch B Prime ISE Employee Guest Tunnel Switch AP CAPWAP Tunnels Cisco Catalyst 3850 Series Specifications Switch Performance Table 7 shows Cisco Catalyst 3850 Series Switches performance specifications Table 7 Cisco Catalyst 3850 Performance Specifications Performance Numbers for All Switch Models Switching capacity 176 Gbps on 48 port models 88 Gbps on 24 port models Stacking bandwidth 480 Gbps Total number of MAC addresses 32 000 Total number of IPv4 routes ARP plus learned routes 24 000 2013 Cisco and or its affiliates This document is Cisco Public Information Page 17 of 28 Performance Numbers for All Switch Mode
5. TIDTIIT CISCO Data Sheet Cisco Catalyst 3850 Series Switches The Cisco Catalyst 3850 Series is the next generation of enterprise class stackable access layer switches that provide full convergence between wired and wireless on a single platform Cisco s new Unified Access Data Plane UADP application specific integrated circuit ASIC powers the switch and enables uniform wired wireless policy enforcement application visibility flexibility and application optimization This convergence is built on the resilience of the new and improved Cisco StackWise 480 The Cisco Catalyst 3850 Series Switches support full IEEE 802 3at Power over Ethernet Plus PoE modular and field replaceable network modules redundant fans and power supplies Product Overview e Integrated wireless controller capability with o Up to 40G of wireless capacity per switch 48 port models Support for up to 50 access points and 2000 wireless clients on each switching entity switch or stack e 24 and 48 10 100 1000 data and PoE models with energy efficient Ethernet EEE Cisco StackWise 480 technology provides scalability and resiliency with 480 Gbps of stack throughput o Cisco StackPower technology provides power stacking among stack members for power redundancy Three optional uplink modules with 4 x Gigabit Ethernet 2 x 10 Gigabit Ethernet or 4 x 10 Gigabit Ethernet ports Dual redundant modular power supplies and three modular fans providing redundan
6. Software Policy for Cisco Catalyst 3850 Series Switches Customers with Cisco Catalyst LAN Base and IP Base software feature sets will be provided with maintenance updates and bug fixes designed to maintain the compliance of the software with published specifications release notes and industry standards compliance as long as the original end user continues to own or use the product or up to one year from the end of sale date for this product whichever occurs earlier Customers with licenses for our IP Services software images require a service support contract such as Cisco SMARTnef Service to download updates This policy supersedes any previous warranty or software statement and is subject to change without notice Cisco and Partner Services for Next Generation Cisco Catalyst Fixed Switches Enable the innovative secure intelligent edge in the Borderless Network Architecture using personalized services from Cisco and our partners Through a discovery process that begins with understanding your business objectives we help you integrate the next generation Cisco Catalyst fixed switches into your architecture and incorporate network services onto that platform Sharing knowledge and leading practices we support your success every step of the way as you deploy absorb manage and scale new technology Choose from a flexible suite of support services designed to meet your business needs and help you maintain high quality network performance while co
7. network modules 0 4 1 2 4 x Gigabit Ethernet 4 x10 Gigabit Ethernet 4 0 network modules 0 4 2 2 3 1 1 3 Dual Redundant Modular Power Supplies The Cisco Catalyst 3850 Series Switches support dual redundant power supplies The switch ships with one power supply by default and the second power supply can be purchased at the time of ordering the switch or at a later time If only one power supply is installed it should always be in power supply bay 1 The switch also ships with three field replaceable fans See Figure 3 Figure 3 Dual Redundant Power Supplies 2013 Cisco and or its affiliates This document is Cisco Public Information Page 3 of 28 Table 4 shows the different power supplies available in these switches and available PoE power Table 4 Power Supply Models 24 port de data switch PWR C1 350WAC 48 port data switch 24 port PoE switch PWR C1 715WAC 435W 48 port PoE switch 48 port full PoE switch PWR C1 1100WAC 800W In addition to the power supplies listed in Table 4 a 440WDC power supply is available as a spare should be ordered separately on all switch models The DC power supply also delivers PoE capabilities for maximum flexibility refer to Table 5 for available PoE budget with DC power supplies Customers can mix and match the AC and DC power supplies in the two available power supply slots Any of these power supplies can be installed in any of the switches Table 5 Available PoE with
8. 11 Power Specifications for Cisco Catalyst 3850 Series Power supply rated maximum Total output BTU Note 1000 BTU hr 293W Input voltage range and frequency Input current Output ratings Output holdup time Power supply input receptacles Power cord rating Physical specifications Operating temperature Storage temperature Relative humidity operating and non operating noncondensing Altitude MTBF EMI and EMC compliance Safety compliance LED indicators PWR C1 350WAC 350W 1207BTU hr 350W PWR C1 440WDC 440W 1517BTU hr 440W PWR C1 1100WAC 1100W 3793 BTU hr 1100W PWR C1 715WAC 715W 2465 BTU hr 715W 115 240VAC 100 240VAC 100 240VAC 36VDC to 72VDC 50 60 Hz 50 60 Hz 50 60 Hz 12 6A 10 5A 4 2A lt 8A 72VDC 16AQ 36VDC 56V 19 64A 56V 12 8A 56V 6 25A 56V 7 86A 10 ms minimum 16 7 ms minimum 2 16 7 ms minimum gt 2ms 48VDC 102 5VAC 100VAC 100VAC IEC 320 C16 IEC 320 C16 IEC 320 C16 IEC60320 Terminal strip IEC60320 C16 IEC60320 C16 C16 13A 13A 10A 20A 100VDC HxWxD 1 58X3 25X HxWxD 1 58X3 25 HxWxD 1 58X3 25 HXWXx D 1 58 X 3 25 13 7 in X 12 20 in X 12 20 in X 12 20 in Weight 3 Ib Weight 2 8 Ib Weight 2 6 Ib Weight 2 6 Ib 1 4 kg 1 3 kg 1 2 kg 1 2 kg 23 to 113F 5 to 450 40 to 158 fF 40 to 70 5 to 9096 noncondensing 10 000 ft 3000 meters up to 45C Calculated MTBF must be greater than 300 000 using Telcordia SR 332 Metho
9. 4 10G 0 75 0 34 2013 Cisco and or its affiliates This document is Cisco Public Information Page 18 of 28 MTBF Hours WS C3850 24T WS C3850 24P WS C3850 48T WS C3850 48P WS C3850 48F PWR C1 350WAC PWR C1 715WAC PWR C1 1100WAC PWR C1 440WDC C3850 NM 4 1G C3850 NM 2 10G C3850 NM 4 10G 303 230 269 450 303 660 241 050 241 050 580 710 664 055 392 174 469 350 7 052 100 4 315 970 3 835 330 Environmental Ranges With AC power supply Operating environment and altitude With DC power supply Operating environment and altitude NEBS Relative humidity Acoustic noise Measured per ISO 7779 and declared per ISO 9296 Bystander positions operating to an ambient temperature of 25 C Storage environment Vibration Shock Normal operating temperature and altitudes 5 C to 45 C up to 5000 feet 1500m 5 C to 40 C up to 10 000 feet 3000m Minimum ambient temperature for cold start is 32 0 C Short term exceptional conditions 5 C to 50 C up to 5000 feet 1500m 5 C to 45 C up to 10 000 feet 3000m 5 C to 45 C at sealevel with single fan failure Not more than following in one year period 96 consecutive hours or 360 hours total or 15 occurrences Normal operating temperature and altitudes 5 C to 45 C up to 6000 feet 1800m 5 C to 40 C up to 10 000 feet 3000m 5 C to 35 C up to 13 000 feet 4000m Short term exceptional conditions
10. DC Power Supply a Number of 440WDC Power Supplies Total Available PoE Bu DNEUETI MD Budget 24 port PoE switch 220W 2 660W 48 port PoE switch 1 185W 2 625W Power over Ethernet Plus PoE In addition to PoE IEEE 802 3af the Cisco Catalyst 3850 Series Switches support PoE IEEE 802 3at standard which provides up to 30W of power per port The Cisco Catalyst 3850 Series Switches can provide a lower total cost of ownership TCO for deployments that incorporate Cisco IP phones Cisco Aironet wireless LAN WLAN access points or any IEEE 802 3at compliant end device PoE removes the need for wall power to each PoE enabled device and eliminates the cost for additional electrical cabling and circuits that would otherwise be necessary in IP phone and WLAN deployments Table 6 shows the power supply combinations required for different PoE needs Table 6 Power Supply Requirements for PoE and PoE PoE on all ports 15 4W per port One PWR C1 715WAC One PWR C1 1100WAC or two PWR C1 715WAC PoE on all ports 30W per port One PWR C1 1100WAC or two PWR C1 Two PWR C1 1100WAC or one PWR C1 715WAC 1100WAC and one PWR C1 715WAC 2013 Cisco and or its affiliates This document is Cisco Public Information Page 4 of 28 Benefits Converged Wired plus Wireless Access The Cisco Catalyst 3850 is the first stackable access switching platform that enables wired plus wireless services on a single Cisco IOS XE Software based platform With thi
11. capabilities The Cisco Catalyst 3850 ports are capable of reduced power modes so that ports not in use can move into a lower power utilization state Other efficient switch operation features are e Cisco Discovery Protocol Version 2 allows the Cisco Catalyst 3850 Series Switches to negotiate a more granular power setting when connecting to a Cisco powered device such as IP phones or access points than what is provided by IEEE classification e Per port power consumption command allows customers to specify maximum power setting on an individual port Per port PoE power sensing measures actual power being drawn enabling more intelligent control of powered devices e The PoE MIB provides proactive visibility into power usage and allows customers to set different power level thresholds Environmentally Responsible Organizations may choose to turn off access point radios to reduce power consumption during off peak hours The integrated wireless LAN controller avoids the deployment of additional devices in the network Network Management Tools The Cisco Catalyst 3850 Series Switches offer both a superior CLI for detailed configuration and Cisco Prime infrastructure for unified wired plus wireless management Prime infrastructure provides day 0 and ongoing provisioning ongoing monitoring and maintenance configuration templates and device and user 360 degree views and serves as the FNF collector for user traffic views using the Prime Assurance M
12. dense mode PIM DM PIM sparse dense mode and source specific multicast SSM The IP Services feature set is required IPv6 addressing is supported on interfaces with appropriate show commands for monitoring and troubleshooting Superior QoS The Cisco Catalyst 3850 Series offers Gigabit Ethernet speed with intelligent services that keep traffic flowing smoothly even at 10 times the normal network speed Industry leading mechanisms for cross stack marking classification and scheduling deliver superior performance for data voice and video traffic all at wire speed The following are some of the QoS features supported in the Cisco Catalyst 3850 Series Switches Granular wireless bandwidth management and fair sharing use Cisco s proven Cisco IOS Software and UADP ASIC technology to provide hierarchical bandwidth management at line rate per access point per radio per SSID per client based policies Fair sharing across the users within an SSID makes sure that no single user is starved because of other heavy hitting users Fair sharing is automatically enabled for wireless at user level as well as SSID level 802 1p CoS and DSCP field classification is provided using marking and reclassification on a per packet basis by source and destination IP address MAC address or Layer 4 Transmission Control Protocol User Datagram Protocol TCP UDP port number Shaped round robin SRR scheduling helps ensure differential prioritization of pack
13. given SSID This 2013 Cisco and or its affiliates This document is Cisco Public Information Page 6 of 28 makes sure that all users within a given SSID get a fair share of the available bandwidth while being connected to the network The UADP ASIC enables the hierarchical bandwidth management and fair sharing of bandwidth thereby providing hardware based QoS for optimized performance at line rate traffic In addition to these capabilities the switch is able to do class of service CoS or differentiated services code point DSCP based queuing policing shaping and marking of wired plus wireless traffic This enables users to create common policies that can be used across wired plus wireless traffic The 3850 also supports downloadable policy names from the Cisco Identity Services Engine ISE when a user successfully authenticates to the network using the ISE Security The Cisco Catalyst 3850 provides a rich set of security features for wired plus wireless users Features such as IEEE 802 1x Dynamic Host Configuration Protocol DHCP snooping IP Source Guard and control plane protection wireless intrusion prevention systems WIPSs and so on enable protection against unauthorized users and attackers With a variety of wired plus wireless users connecting to the network the switch supports session aware networking in which each device connected to the network is identified as one session and unique access control lists ACLs and or Q
14. set of capabilities that simplify LAN deployment configuration and troubleshooting In addition to adaptive always on technologies such as StackWise 480 and StackPower Cisco Catalyst Smart Operations enable zero touch installation and replacement of switches fast upgrade and ease of troubleshooting with reduced operational cost Cisco Catalyst Smart Operations are a set of features that includes Smart Install Auto Smartports Smart Configuration and Smart Troubleshooting to enhance operational excellence Cisco Smart Install is a transparent plug and play technology to configure the Cisco IOS Software image and switch configuration without user intervention Smart Install utilizes dynamic IP address allocation and the assistance of other switches to facilitate installation providing transparent network plug and play Cisco Auto Smartports provide automatic configuration as devices connect to the switch port allowing auto detection and plug and play of the device onto the network Cisco Smart Troubleshooting is an extensive array of debug diagnostic commands and system health checks within the switch including Generic Online Diagnostics GOLD and Onboard Failure Logging OBFL Embedded Event Manager EEM is a powerful and flexible feature that provides real time network event detection and onboard automation Using EEM customers can adapt the behavior of their network devices to align with their business needs This feature requir
15. 00 flow entries on 24 port models across wired plus wireless With UADP ASIC Cisco Catalyst 3850 delivers next generation flow technology with unprecedented flexibility and comprehensive visibility extending from Layer 2 MAC and VLAN to Layer 4 TCP UDP flags and so on across wired plus wireless traffic The Cisco Catalyst 3850 switch is Medianet capable to provide visibility and troubleshooting capabilities across wired plus wireless video traffic Specific Medianet features will be enabled in future software updates The flow data collected by FNF can be exported to an external collector for analysis and reporting or tracked by the EEM The Cisco Catalyst 3850 enables powerful on box and customizable event correlation and policy actions with EEM allowing the switches to trigger customized event alarms or policy actions when the predefined condition is met With no external appliance required customers are able to use existing infrastructure to perform traffic monitoring making traffic analysis economical even on a large IP network Details about Cisco FNF are available at http www cisco com en US prod collateral iosswrel ps6537 ps6555 ps6601 ps6965 product data sheet0900aecd 804b590b html High performance video over wireless integrates Cisco VideoStream technology to optimize the delivery of video applications across the WLAN Wired plus wireless IP telephony supports unified communications for improved collaboration through messaging
16. 17 59 689 WS C3850 48P 12535 12445 12515 12448 i WS C3850 48F 130 10 128 91 129 85 12918 WS C3850 24T 03850 NM 2 10G 81 97 81 83 8497 8216 WS C3850 24P 85 22 8504 88 32 85 39 WS C3850 48T 117 56 116 74 120 40 117 28 WS C3850 48P p 123 78 122 90 126 75 123 42 WS C3850 48F 129 89 129 06 13236 948 WS C3850 48T C3850 NM 4 10G 120 56 120 28 127 24 121 02 i WS C3850 48P 129 59 129 64 185 96 18027 WS C3850 48F 48757 017006 377 eet Safety and Compliance Table 13 lists the safety and compliance information for the Cisco Catalyst 3850 Series Table 13 Safety and Compliance Information for Cisco Catalyst 3850 Series Safety certifications UL 60950 1 Second Edition CAN CSA C22 2 No 60950 1 Second Edition EN 60950 1 Second Edition IEC 60950 1 Second Edition GOST NOM obtained by partners and distributors Electromagnetic emissions 47CFR Part 15 CFR 47 Class A FCC Part 15 Class A certifications AS NZS CISPR22 Class A CISPR22 Class A EN55022 Class A ICES003 Class A VCCI Class A EN61000 3 2 EN61000 3 3 KN22 Class A KCC CNS13438 Class A EN55024 CISPR24 KN24 Environmental Reduction of Hazardous Substances ROHS 5 Noise specifications Office Product Spec 48dBA at 30 refer to ISO 7779 Telco CLEI code 2013 Cisco and or its affiliates This document is Cisco Public Information Page 23 of 28 Cisco Enh
17. 802 3ad This feature is similar to Cisco EtherChannel technology and PAgP Unidirectional Link Detection Protocol UDLD and aggressive UDLD allow unidirectional links caused by incorrect fiber optic wiring or port faults to be detected and disabled on fiber optic interfaces Cisco VLAN Trunking Protocol VTP Version 3 supports dynamic VLANs and dynamic trunk configuration across all switches e Efficient switch operation Switching database manager SDM templates VLAN template specific to LAN Base license level and advanced template allow the administrator to automatically optimize the ternary content addressable memory TCAM allocation to the desired features based on deployment specific requirements Local proxy Address Resolution Protocol ARP works in conjunction with private VLAN edge to minimize broadcasts and maximize available bandwidth Stacking master configuration management with Cisco StackWise 480 technology helps make sure that all switches are automatically upgraded when the master switch receives a new software version Automatic software version checking and updating help ensure that all stack members have the same software version Trivial File Transfer Protocol TFTP reduces the cost of administering software upgrades by downloading from a centralized location o Network Timing Protocol NTP provides an accurate and consistent timestamp to all intranet switches e Multicast Optimized multic
18. ASE SR LR LRM CX1 v02 or higher SFP transceivers LC fiber connectors single mode or multimode fiber Cisco StackWise 480 stacking ports copper based Cisco StackWise cabling Cisco StackPower Cisco proprietary power stacking cables Ethernet management port RJ 45 connectors 4 pair Cat 5 UTP cabling Management console port RJ 45 to DB9 cable for PC connections Customers can provide power to a switch by using either the internal power or StackPower from another member in the power stack The connectors are located at the back of the switch Internal power supply connector The internal power supply is an auto ranging unit The internal power supply supports input voltages between 100 and 240VAC Use the supplied AC power cord to connect the AC power connector to an AC power outlet Management and Standards Support for Cisco Catalyst 3850 Series Switches Table 10 shows management and standards support for the Cisco Catalyst 3850 Series Table 10 Management and Standards Support for the Cisco Catalyst 3850 Series Management BRIDGE MIB CISCO AUTH FRAMEWORK MIB CISCO BGP4 MIB BGP4 MIB CISCO BRIDGE EXT MIB CISCO BULK FILE MIB CISCO CABLE DIAG MIB CISCO CALLHOME MIB CISCO CEF MIB CISCO CIRCUIT INTERFACE MIB CISCO ENTITY VENDORTYPE OID MIB CISCO CONTEXT MAPPING MIB CISCO DEVICE LOCATION MIB CISCO DHCP SNOOPING MIB CISCO EIGRP MIB CISCO EMBEDDED EVENT MGR MIB CISCO ENTITY FRU CONTROL MIB CISCO ENTITY SENSOR M
19. E 802 1w IEEE 802 11 IEEE 802 1x IEEE 802 1x Rev IEEE 802 3ad IEEE 802 3af IEEE 802 3at IEEE 802 3x full duplex on 10BASE T 100BASE TX and 1000BASE T ports IEEE 802 1D Spanning Tree Protocol IEEE 802 1p CoS prioritization IEEE 802 1Q VLAN IEEE 802 3 10BASE T specification IEEE 802 3u 100BASE TX specification IEEE 802 3ab 1000BASE T specification IEEE 802 3z 1000BASE X specification 2013 Cisco and or its affiliates This document is Cisco Public Information SNMP FRAMEWORK MIB SNMP MPD MIB SNMP NOTIFICATION MIB SNMP PROXY MIB SNMP TARGET MIB SNMP USM MIB SNMPv2 MIB SNMP VIEW BASED ACM MIB TCP MIB UDP MIB CISCO IMAGE MIB CISCO STACKWISE MIB AIRESPMACE WIRELESS MIB SCO LWAPP IDS MIB SCO LWAPP AP MIB SCO LWAPP CCX RM MIB SCO LWAPP CLIENT ROAMING MIB SCO LWAPP DOT11 CCX CLIENT DIAG MIB SCO LWAPP DOT11 CCX CLIENT MIB SCO LWAPP DOT11 CLIENT CCX REPORTS MIB SCO LWAPP DOT11 CLIENT MIB SCO LWAPP DOT11 MIB SCO LWAPP DOWNLOAD MIB SCO LWAPP LINKTEST MIB SCO LWAPP MFP MIB SCO LWAPP MOBILITY EXT MIB SCO LWAPP QOS MIB SCO LWAPP REAP MIB SCO LWAPP ROGUE MIB SCO LWAPP RRM MIB SCO LWAPP SI MIB SCO LWAPP TSM MIB SCO LWAPP WLAN MIB SCO LWAPP WLAN SECURITY MIB RMON and II standards SNMPv1 SNMPv2c and SNMPv3 Oo0o00o000000000000500570505505 Page 21 of 28 Power Supply Specifications Table 11 lists the power specifications for the Cisco Catalyst 3850 Series based on the kind of power supply used Table
20. IB ENTITY MIB CISCO ERR DISABLE MIB CISCO CONFIG COPY MIB CISCO FLOW MONITOR MIB CISCO FTP CLIENT MIB CISCO HSRP EXT MIB CISCO HSRP MIB CISCO IETF ISIS MIB CISCO IF EXTENSION MIB CISCO IGMP FILTER MIB CISCO CONFIG MAN MIB CISCO IP CBR METRICS MIB 2013 Cisco and or its affiliates This document is Cisco Public Information CISCO SNMP TARGET EXT MIB CISCO STACKMAKER MIB CISCO MEMORY POOL MIB CISCO STP EXTENSIONS MIB CISCO SYSLOG MIB CISCO TCP MIB CISCO UDLDP MIB CISCO VLAN IFTABLE RELATIONSHIP MIB CISCO VLAN MEMBERSHIP MIB CISCO VTP MIB EtherLike MIB HC RMON MIB IEEE8021 PAE MIB IEEE8023 LAG MIB IF MIB IGMP MIB IGMP STD MIB IP FORWARD MIB IP MIB IPMROUTE STD MIB LLDP EXT MED MIB LLDP MIB NOTIFICATION LOG MIB OLD CISCO MEMORY MIB CISCO CDP MIB POWER ETHERNET MIB RMON2 MIB RMON MIB SNMP COMMUNITY MIB Page 20 of 28 Standards CISCO IPMROUTE MIB CISCO IP STAT MIB CISCO IP URPF MIB CISCO L2L3 INTERFACE CONFIG MIB CISCO LAG MIB CISCO LICENSE MGMT MIB CISCO MAC AUTH BYPASS MIB CISCO MAC NOTIFICATION MIB CISCO MDI METRICS MIB CISCO FLASH MIB CISCO OSPF MIB CISCO OSPF TRAP MIB CISCO PAE MIB CISCO PAGP MIB CISCO PIM MIB CISCO PING MIB CISCO PORT QOS MIB CISCO PORT SECURITY MIB CISCO PORT STORM CONTROL MIB CISCO POWER ETHERNET EXT MIB CISCO PRIVATE VLAN MIB CISCO PROCESS MIB CISCO PRODUCTS MIB CISCO RF MIB CISCO RTP METRICS MIB CISCO RTTMON MIB CISCO SMART INSTALL MIB IEEE 802 1s IEE
21. anager module For detailed information about Cisco Prime infrastructure go to http www cisco com en US products ps12239 index html Advanced Security Features Cisco Catalyst 3850 Series Switches support advanced security features including but not limited to e Protection against attackers Port security secures the access to an access or trunk port based on MAC address It limits the number of learned MAC addresses to deny MAC address flooding DHCP snooping prevents malicious users from spoofing a DHCP server and sending out bogus addresses This feature is used by other primary security features to prevent a number of other attacks such as ARP poisoning Dynamic ARP inspection DAI helps ensure user integrity by preventing malicious users from exploiting the insecure nature of ARP o IP source guard prevents a malicious user from spoofing or taking over another user s IP address by creating a binding table between the client s IP and MAC address port and VLAN 2013 Cisco and or its affiliates This document is Cisco Public Information Page 11 of 28 o o The Unicast Reverse Path Forwarding RPF feature helps mitigate problems caused by the introduction of malformed or forged spoofed IP source addresses into a network by discarding IP packets that lack a verifiable IP source address Bidirectional data support on the SPAN port allows the Cisco intrusion detection system IDS to take action when an intru
22. anced Limited Lifetime Hardware Warranty The Cisco Catalyst 3850 Series Switches come with an E LLW that includes NBD delivery of replacement hardware where available and 90 days of 8x5 Cisco TAC support Your formal warranty statement including the warranty applicable to Cisco software appears in the Cisco information packet that accompanies your Cisco product We encourage you to review carefully the warranty statement shipped with your specific product before use Cisco reserves the right to refund the purchase price as its exclusive warranty remedy For further information on warranty terms visit http www cisco com go warranty Table 14 provides information about the E LLW Table 14 E LLW Details Device covered Applies to Cisco Catalyst 3850 Series Switches Warranty duration As long as the original end user continues to own or use the product provided that fan and power supply warranty is limited to 5 years EoL policy In the event of discontinuance of product manufacture Cisco warranty support is limited to 5 years from the announcement of discontinuance Hardware replacement Cisco or its service center will use commercially reasonable efforts to ship a replacement for NBD delivery where available Otherwise a replacement will be shipped within 10 working days after receipt of the RMA request Actual delivery times might vary depending on customer location Effective date Hardware warranty commences from the date of shipme
23. ast for wired plus wireless Cisco Catalyst 3850 offers greater multicast efficiency by receiving only one multicast stream and replicating it for all connected wired plus wireless devices connected to that switch Internet Group Management Protocol IGMP v1 v2 v3 snooping for IPv4 multicast listener discovery MLD v1 and v2 snooping provides fast client joins and leaves of multicast streams and limits bandwidth intensive video traffic to only the requestors e Monitoring o Remote Switch Port Analyzer RSPAN allows administrators to remotely monitor ports in a Layer 2 Switch network from any other switch in the same network For enhanced traffic management monitoring and analysis the Embedded Remote Monitoring RMON software agent supports four RMON groups history statistics alarms and events Layer 2 traceroute eases troubleshooting by identifying the physical path that a packet takes from Source to destination Wireless RF management provides both real time and historical information about RF interference affecting network performance across controllers using systemwide Cisco CleanAir technology integration 2013 Cisco and or its affiliates This document is Cisco Public Information Page 10 of 28 Efficient Switch Operation Cisco Catalyst 3850 Series Switches designed and engineered by Cisco provide optimum power saving EEE low power operations for industry best in class power management and power consumption
24. choose from the network modules described in Table 2 Figure 2 shows various network modules e 4 x Gigabit Ethernet with Small Form Factor Pluggable SFP e 2x10 Gigabit Ethernet with SFP or 4 x Gigabit Ethernet with SFP e 4x 10 Gigabit Ethernet with SFP supported on the 48 port models only Figure 2 Network Modules with Four Gigabit Ethernet Two 10 Gigabit Ethernet SFP or Four 10 Gigabit Ethernet SFP Interfaces 2013 Cisco and or its affiliates This document is Cisco Public Information Page 2 of 28 Table 2 Network Module Numbers and Descriptions Product Number Product Description C3850 NM 4 1G 4 x Gigabit Ethernet network modules C3850 NM 2 10G 4 x Gigabit Ethernet 2 x 10 Gigabit Ethernet network modules C3850 NM 4 10G 4 x Gigabit Ethernet 4 x 10 Gigabit Ethernet network modules The C3850 NM 4 10G module is supported on the 48 port models only The SFP interface supports both 10 Gigabit Ethernet and Gigabit Ethernet ports allowing customers to use their investment in Gigabit Ethernet SFP and upgrade to 10 Gigabit Ethernet when business demands change without having to do a comprehensive upgrade of the access switch The three network modules are hot swappable and can be used in any of the combinations shown in Table 3 Table 3 Network Module Configurations Network Module 10 Gigabit Ethernet SFP Ports Gigabit Ethernet SFP Ports 4 x Gigabit Ethernet 0 4 4 x Gigabit Ethernet 2 x10 Gigabit Ethernet 2 0
25. co Public Information Page 5 of 28 Figure 4 Mobility Controller MC and Mobility Agent MA New WLC 5760 AP CAPWAP Tunnels Mobility Tunnels Distributed Intelligent Services Flexible NetFlow FNF Full visibility into the wired plus wireless traffic is achieved because of the access point Control and Provisioning of Wireless Access Points CAPWAP tunnel termination on the switch This helps identify users and user traffic flows in order to identify potential attackers and take corrective action at the access layer before the attack penetrates further into the network This is achieved using FNF which monitors every single flow entering and exiting the switch stack for wired and wireless users It also helps identify the top wired wireless talkers and enforce appropriate bandwidth provisioning policies QoS The 3850 switch has advanced wired plus wireless QoS capabilities It uses the Cisco modular QoS command line interface MQC The switch manages wireless bandwidth using unprecedented hierarchical bandwidth management starting at the per access point level and drilling further down to per radio per service set identification SSID and per user levels This helps manage and prioritize available bandwidth between various radios and various SSIDs enterprise guest and so on within each radio on a percentage basis The switch is also capable of automatically allocating equal bandwidth among the connected users within a
26. cy Full IEEE 802 3at PoE with 30W power on all ports in 1 rack unit RU form factor e Software support for IPv4 and IPv6 routing multicast routing modular quality of service QoS Flexible NetFlow FNF Version 9 and enhanced security features e Single universal Cisco IOS Software image across all license levels providing an easy upgrade path for software features e Enhanced limited lifetime warranty E LLW with next business day NBD advance hardware replacement and 90 day access to Cisco Technical Assistance Center TAC support 2013 Cisco and or its affiliates This document is Cisco Public Information Page 1 of 28 Switch Configurations All switches ship with one of the four power supplies 350WAC 715WAC 1100WAC or 440WDC Figure 1 shows the Cisco Catalyst 3850 Series Switches Figure 1 Cisco Catalyst 3850 Series Switches Table 1 shows the Cisco Catalyst 3850 Series configurations Table 1 Cisco Catalyst 3850 Series Configurations Total 10 100 1000 Default AC Power Supply Available PoE Power StackPower Ethernet Ports 24 Yes WS C3850 24T 350WAC WS C3850 48T 48 WS C3850 24P 24 PoE 715WAC 435W WS C3850 48P 48 PoE WS C3850 48F 48 PoE 1100WAC 800W Network Modules The Cisco Catalyst 3850 Series Switches support three optional network modules for uplink ports The default switch configuration doesn t include the uplink module At the time of switch purchase the customer has the flexibility to
27. d 1 Case 3 Demonstrated MTBF is 500 000 hr with 9096 confidence level FCC Part 15 CFR 47 Class A ICES 003 Class A EN 55022 Class A CISPR 22 Class A AS NZS 3548 Class A BSMI Class A AC input models only VCCI Class A EN 55024 EN300386 EN 50082 1 EN 61000 3 2 EN 61000 3 3 EN61000 4 2 EN61000 4 3 EN61000 4 4 EN61000 4 5 EN61000 4 6 EN 61000 6 1 UL 60950 1 CAN CSA C22 2 No 60950 1 EN 60950 1 IEC 60950 1 CCC CE Marking AC OK Input power to the power supply is OK PS OK Output power from the power supply is OK Power Consumption of Standalone Cisco Catalyst 3850 Series Switches Table 12 shows power consumption of standalone Cisco Catalyst 3850 Series Switches based on Alliance for Telecommunications Industry Solutions ATIS testing using IMIX distribution stream traffic with input voltage of 115VAC 60 Hz and no PoE loading The values given are the maximum possible power consumption numbers under the respective test scenarios 2013 Cisco and or its affiliates This document is Cisco Public Information Page 22 of 28 Table 12 Power EDS in Watts of Standalone Cisco Catalyst 3850 Series Power Consumption W No More Than Uplink Module Module i 0 Traffic 10 Traffic 100 Traffic aeiee Average WS C3850 24T C3850 NM 4 1G 83 47 82 86 83 76 83 04 WS C3850 24P 86 81 8622 8741 86 40 i WS C3850 48T 117 74 116 62 41
28. d either provide power redundancy for any of the stack members or simply add more power to the shared pool StackPower eliminates the need for an external redundant power system or installation of dual power supplies in all the stack members StackPower is available in LAN Base license level or higher For LAN Base cables need to be purchased separately Foundation for Open Network Environment The heart of the Cisco Catalyst 3850 is the UADP ASIC with programmability for future features and intelligence with investment protection The new ASIC provides the foundation for converged APIs across wired and wireless Cisco Open Network Environment software defined networking SDN readiness and OnePK SDK through software updates over the product lifetime Software Features and Services on Cisco Catalyst 3850 Series Switches Software services supported on the Cisco Catalyst 3850 Series Switches can be classified into five broad categories e Ease of operations Advanced security features Resiliency Application visibility and control 2013 Cisco and or its affiliates This document is Cisco Public Information Page 8 of 28 Ease of Operations The Cisco Catalyst 3850 help reduce the operating costs through Cisco Catalyst Smart Operations e Easy to use deployment and control features e Efficient switch operations e Network management tools Cisco Catalyst Smart Operations Cisco Catalyst Smart Operations are a comprehensive
29. der is detected User authentication o Flexible authentication that supports multiple authentication mechanisms including 802 1X MAC authentication bypass and web authentication using a single consistent configuration RADIUS change of authorization and downloadable calls for comprehensive policy management capabilities Private VLANS restrict traffic between hosts in a common segment by segregating traffic at Layer 2 turning a broadcast segment into a nonbroadcast multiaccess like segment Private VLAN edge provides security and isolation between switch ports which helps ensure that users cannot snoop on other users traffic Multidomain authentication allows an IP phone and a PC to authenticate on the same switch port while placing them on appropriate voice and data VLAN MAC address notification allows administrators to be notified of users added to or removed from the network Mobility and security for secure reliable wireless connectivity and consistent end user experience Increased network availability through proactive blocking of known threats IGMP filtering provides multicast authentication by filtering out nonsubscribers and limits the number of concurrent multicast streams available per port e ACLs o o Cisco security VLAN ACLs on all VLANs prevent unauthorized data flows from being bridged within VLANs Cisco standard and extended IP security router ACLs define security policies on routed interfaces f
30. e set StackPower cables need to be purchased separately WS C3850 48P L Stackable 48 10 100 1000 Ethernet PoE ports with 715WAC power supply 1 RU LAN Base feature set StackPower cables need to be purchased separately WS C3850 48F L Stackable 48 10 100 1000 Ethernet PoE ports with 1100WAC power supply 1 RU LAN Base feature set StackPower cables need to be purchased separately WS C3850 24T S Stackable 24 10 100 1000 Ethernet ports with 350WAC power supply 1 RU IP Base feature set WS C3850 48T S Stackable 48 10 100 1000 Ethernet ports with 350WAC power supply 1 RU IP Base feature set WS C3850 24P S Stackable 24 10 100 1000 Ethernet PoE ports with 715WAC power supply 1 RU IP Base feature set WS C3850 48P S Stackable 48 10 100 1000 Ethernet PoE ports with 715WAC power supply 1 RU IP Base feature set WS C3850 48F S Stackable 48 10 100 1000 Ethernet PoE ports with 1100WAC power supply 1 RU IP Base feature set WS C3850 24T E Stackable 24 10 100 1000 Ethernet ports with 350WAC power supply 1 RU IP Services feature set WS C3850 48T E Stackable 48 10 100 1000 Ethernet ports with 350WAC power supply 1 RU IP Services feature set WS C3850 24P E Stackable 24 10 100 1000 Ethernet PoE ports with 715WAC power supply 1 RU IP Services feature set 2013 Cisco and or its affiliates This document is Cisco Public Information Page 26 of 28 Product Number Product Description WS C3850 48P E Stackable 48 10 100 1000 Ethernet P
31. eatures such as EIGRP OSPF BGP PIM and IPv6 routing such as OSPFv3 and EIGRPve All software feature sets support advanced security and MQC based QoS The Cisco Catalyst 3850 Series Switches with LAN Base feature set can only stack with other Cisco Catalyst 3850 Series LAN Base switches The same applies to IP Base and IP Services as well A mixed stack of LAN Base switch with IP Base or IP Services feature set is not supported 2013 Cisco and or its affiliates This document is Cisco Public Information Page 24 of 28 Customers can transparently upgrade the software feature set in the Cisco Catalyst 3850 Series Switches through Cisco IOS Software CLI using the right to use RTU based software upgrade process Software activation enables the Cisco IOS Software feature sets Based on the license s type Cisco IOS Software activates the appropriate feature set License types can be changed or upgraded to activate a different feature set Access Point License for Cisco Catalyst 3850 An access point license is required for Cisco Catalyst 3850 operating in mobility controller mode No access point license is required for 3850 operating in mobility agent mode This functionality is included in the IP Base feature set Other devices that can act as mobility controller are the WLC 5760 WLC 5508 and WiSM2 wireless controllers Access point licenses can be transferred only between two 3850 switches or between 3850 and 5760 controller and vice versa
32. es the IP Base feature set Easy to Use Deployment and Control Features e User experience o 2013 Cisco and or its affiliates This document is Cisco Public Information IP service level agreements SLAs enable customers to assure new business critical IP applications as well as IP services that utilize data voice and video in an IP network This feature requires the IP Services feature set DHCP autoconfiguration of multiple switches through a boot server eases switch deployment Automatic QoS AutoQoS simplifies QoS configuration in voice over IP VoIP networks by issuing interface and global switch commands to detect Cisco IP phones classify traffic and help enable egress queue configuration Autonegotiation on all ports automatically selects half or full duplex transmission mode to optimize bandwidth Automatic media dependent interface crossover MDIX automatically adjusts transmit and receive pairs if an incorrect cable type crossover or straight through is installed Page 9 of 28 e Simplified configuration and connectivity Dynamic Trunking Protocol DTP facilitates dynamic trunk configuration across all switch ports Port Aggregation Protocol PAgP automates the creation of Cisco Fast EtherChannel groups or Gigabit EtherChannel groups to link to another switch router or server Link Aggregation Control Protocol LACP allows the creation of Ethernet channeling with devices that conform to IEEE
33. et flows by intelligently servicing the ingress queues and egress queues Weighted tail drop WTD provides congestion avoidance at the ingress and egress queues before a disruption occurs Strict priority queuing helps ensure that the highest priority packets are serviced ahead of all other traffic The Cisco committed information rate CIR function provides bandwidth in increments as low as 8 Kbps Rate limiting is provided based on source and destination IP address source and destination MAC address Layer 4 TCP UDP information or any combination of these fields using QoS ACLs IP ACLs or MAC ACLs class maps and policy maps Eight egress queues per port for wired traffic and four egress queues for wireless help enable differentiated management of different traffic types across the stack for wired traffic Up to 2000 aggregate policers are available per switch 2013 Cisco and or its affiliates This document is Cisco Public Information Page 14 of 28 Application Visibility and Control Using Flexible NetFlow Cisco IOS Software FNF is the next generation in flow visibility technology allowing optimization of the network infrastructure reducing operation costs and improving capacity planning and security incident detection with increased flexibility and scalability The Cisco Catalyst 3850 provides optimized application visibility with FNF across wired plus wireless The switch is capable of 48 000 flow entries on 48 port models and 24 0
34. gineering Service Valid Cisco SMARTnet or SP Base contracts on all network equipment are required Notes Cisco operating system updates include the following maintenance releases minor updates and major updates within the licensed feature set Advance hardware replacement is available in various service level combinations For example 8x5xNBD indicates that shipment will be initiated during the standard 8 hour business day 5 days a week the generally accepted business days within the relevant region with NBD delivery Where NBD is not available same day ship is provided Restrictions apply for details review the appropriate service descriptions Ordering Information Table 16 lists ordering information for the Cisco Catalyst 3850 Series To place an order visit the Cisco Ordering homepage at http www cisco com en US ordering or13 or8 order customer help how to order listing html Table 16 Cisco Catalyst 3850 Series Ordering Information Product Number Product Description Cisco Catalyst 3850 Series WS C3850 24T L Stackable 24 10 100 1000 Ethernet ports with 350WAC power supply 1 RU LAN Base feature set StackPower cables need to be purchased separately WS C3850 48T L Stackable 48 10 100 1000 Ethernet ports with 350WAC power supply 1 RU LAN Base feature set StackPower cables need to be purchased separately WS C3850 24P L Stackable 24 10 100 1000 Ethernet PoE ports with 715WAC power supply 1 RU LAN Base featur
35. hnology The Cisco Catalyst 3850 Series uses the Cisco StackPower technology present on the Cisco Catalyst 3850 Series StackPower is an innovative power interconnect system that allows the power supplies in a stack to be shared as a common resource among all the switches Cisco StackPower unifies the individual power supplies installed in the switches and creates a pool of power directing that power where it is needed Up to four switches can be configured in a StackPower stack with the special connector at the back of the switch using the StackPower cable which is different than the StackWise 480 cables See Figure 4 2013 Cisco and or its affiliates This document is Cisco Public Information Page 7 of 28 Figure 5 StackWise 480 and StackPower Connectors StackPower can be deployed in either power sharing mode or redundancy mode In power sharing mode the power of all the power supplies in the stack is aggregated and distributed among the switches in the stack In redundant mode when the total power budget of the stack is calculated the wattage of the largest power supply is not included That power is held in reserve and used to maintain power to switches and attached devices when one power supply fails enabling the network to operate without interruption Following the failure of one power supply the StackPower mode becomes power sharing StackPower allows customers to simply add one extra power supply in any switch of the stack an
36. itecture delivers extremely high performance IP routing in the Cisco Catalyst 3850 Series Switches e P unicast routing protocols static Routing Information Protocol Version 1 RIPv1 and RIPv2 RIPng Enhanced Interior Gateway Routing Protocol EIGRP stub are supported for small network routing applications with the IP Base feature set Limited static routing with the LAN Base feature set Equal cost routing facilitates Layer 3 load balancing and redundancy across the stack e Advanced IP unicast routing protocols Open Shortest Path First OSPF EIGRP Border Gateway Protocol Version 4 BGPv4 and Intermediate System to Intermediate System Version 4 IS ISv4 are supported for load balancing and constructing scalable LANs IPv6 routing OSPFv3 EIGRPv6 is supported in hardware for maximum performance OSPF for routed access is included in the IP Base image The IP Services feature set is required for full OSPF EIGRP BGPv4 and IS ISv4 2013 Cisco and or its affiliates This document is Cisco Public Information Page 13 of 28 Policy based routing PBR allows superior control by facilitating flow redirection regardless of the routing protocol configured Virtual routing and forwarding VRF Lite enables a service provider to support two or more VPNs with overlapping IP addresses The IP Services feature set is required Protocol independent multicast PIM for IP multicast routing is supported including PIM sparse mode PIM SM PIM
37. ls FNF entries 48 000 flow on 48 port models 24 000 flows on 24 port models DRAM 4 Gb Flash 2 Gb VLAN IDs 4 000 Total switched virtual interfaces SVIs 1 000 Jumbo frame 9198 bytes Total routed ports per 3850 stack 208 Miele Number of access points per switch stack 50 Number of wireless clients per switch stack 2000 Total number of WLANs per switch 64 Wireless bandwidth per switch Up to 40 Gbps on 48 port models Up to 20 Gbps on 24 port models Supported Aironet access point series 3600 3500 2600 1600 1260 1140 1040 3850 24T 65 47 Mpps 3850 24P 3850 48T 130 95 Mpps 3850 48P 3850 48F Dimensions Weight Acoustic Mean Time Between Failure and Environmental Range Specifications for Cisco Catalyst 3850 Series Switches Table 8 shows dimensions weight acoustic mean time between failure MTBF and environmental range Weight does not include an uplink FRU Weight includes the chassis assembly as it is shipped with fans one power supply and and one power supply slot blank Table 8 Dimensions Weight Acoustic MTBF and Environmental Range LCCUUDNMENENEN CCOOUNNE EE ON WS C3850 24T 1 75 x 17 5 x 17 7 4 45 x 44 5 x 45 0 WS C3850 24P WS C3850 48T WS C3850 48P WS C3850 48F 1 75 x 17 5 x 19 2 4 45 x 44 5 x 48 8 Weight Pounds Kilograms WS C3850 24T 15 9 7 2 WS C3850 24P 16 3 74 WS C3850 48T 17 0 7 7 WS C3850 48P 17 4 7 9 WS C3850 48F 17 6 8 0 C3850 NM 4 1G 0 66 0 30 C3850 NM 2 10G 0 71 0 32 C3850 NM
38. nt to customer and in case of resale by a Cisco reseller not more than 90 days after original shipment by Cisco TAC support Cisco will provide during business hours 8 hours per day 5 days per week basic configuration diagnosis and troubleshooting of device level problems for up to a 90 day period from the date of shipment of the originally purchased Cisco Catalyst 3850 product This support does not include solution or network level support beyond the specific device under consideration Cisco com access Warranty allows guest access only to Cisco com Licensing for Cisco Catalyst 3850 Series Switches The three feature sets available with all Cisco Catalyst 3850 Series Switches are e LAN Base Enterprise access layer 2 switching features e P Base Enterprise access layer 3 switching features e IP Services Advanced enterprise layer 3 switching IPv4 and IPv6 features The LAN Base feature set offers enhanced intelligent services that include comprehensive Layer 2 features with up to 255 VLANs The IP Base feature set provides entry level enterprise services in addition to all LAN Base features with 1K VLANs IP Base also includes the support for wireless controller functionality mobility agent and mobility controller role additional access point license required for mobility controller role routed access smart operations FNF and so on The IP Services feature set provides full enterprise services that include advanced Layer 3 f
39. ntrolling operational costs See Table 15 Table 15 Technical Services Available for Cisco Catalyst 3850 Switches Technical Services Cisco SMARTnet Service Around the clock global access to the Cisco TAC Unrestricted access to the extensive Cisco com knowledge base and tools Next business day 8x5x4 24x7x4 and 24x7x2 advance hardware replacement and onsite parts replacement and installation available Ongoing operating system software updates within the licensed feature set Proactive diagnostics and real time alerts on Smart Call Home enabled devices Cisco Smart Foundation Service NBD advance hardware replacement as available Business hours access to SMB TAC access levels vary by region Access to Cisco com SMB knowledge base Online technical resources through Smart Foundation Portal Operating system software bug fixes and patches 2013 Cisco and or its affiliates This document is Cisco Public Information Page 25 of 28 CCS Technical Services Cisco SP Base Service Around the clock global access to the Cisco TAC Registered access to Cisco com NBD 8x5x4 24x7x4 and 24x7x2 advance hardware replacement return to factory option available Ongoing operating system software updates Cisco Focused Technical Support Services Three levels of premium high touch services are available e Cisco High Touch Operations Management Service Cisco High Touch Technical Support Service Cisco High Touch En
40. o services Industry s first unified network wired plus wireless location services enable tracking of mobile assets and the users of those assets for both wired plus wireless devices The true borderless experience is enabled by the following feature sets in the Cisco Catalyst 3850 Series Switches e High availability e High performance IP routing e Superior QoS High Availability In addition to StackWise 480 and StackPower the Cisco Catalyst 3850 Series supports high availability features including but not limited to the following e Cross Stack EtherChannel provides the ability to configure Cisco EtherChannel technology across different members of the stack for high resiliency e Flexlink provides link redundancy with convergence time less than 100ms e EEE 802 1s w Rapid Spanning Tree Protocol RSTP and Multiple Spanning Tree Protocol MSTP provide rapid spanning tree convergence independent of spanning tree timers and also offer the benefit of Layer 2 load balancing and distributed processing Stacked units behave as a single spanning tree node e Per VLAN Rapid Spanning Tree PVRST allows rapid spanning tree reconvergence on a per VLAN spanning tree basis without requiring the implementation of spanning tree instances e Switch port autorecovery Err disable automatically attempts to reactivate a link that is disabled because of a network error High Performance IP Routing The Cisco Express Forwarding hardware routing arch
41. oE ports with 715WAC power supply 1 RU IP Services feature set WS C3850 48F E Stackable 48 10 100 1000 Ethernet PoE ports with 1100WAC power supply 1 RU IP Services feature set Cisco Catalyst 3850 Bundles WS C3850 24PW S Cisco Catalyst 3850 24 port PoE IP Base with 5 access point license WS C3850 48PW S Cisco Catalyst 3850 48 port PoE IP Base with 5 access point license Network Modules for the Cisco Catalyst 3850 Series C3850 NM 4 1G 4 x Gigabit Ethernet network module spare C3850 NM 2 10G 4 x Gigabit Ethernet 2 x 10 Gigabit Ethernet network module spare C3850 NM BLANK Network module blank spare C3850 NM 4 10G 4 x Gigabit Ethernet 4 x 10 Gigabit Ethernet network module spare Software Licenses C3850 24 L S Cisco Catalyst 3850 24 port Switch LAN Base to IP Base paper license C3850 48 L S Cisco Catalyst 3850 48 port Switch LAN Base to IP Base paper license C3850 24 L E Cisco Catalyst 3850 24 port LAN Base to IP Services paper license C3850 48 L E Cisco Catalyst 3850 48 port LAN Base to IP Services paper license C3850 24 S E Cisco Catalyst 3850 24 port IP Base to IP Services paper license C3850 48 S E Cisco Catalyst 3850 48 port IP Base to IP Services paper license L C3850 24 L S Cisco Catalyst 3850 24 port LAN Base to IP Base e license L C3850 48 L S Cisco Catalyst 3850 48 port LAN Base to IP Base e license L C3850 24 L E Cisco Catalyst 3850 24 port LAN Base to IP Services e license L C3850 48 L E Cisco Catalyst 3850 48 port LAN Base
42. oS policies can be defined and applied using the ISE for each of these sessions providing better control on the devices connecting to the network Resiliency Cisco StackWise 480 Technology Cisco StackWise 480 technology is built on the highly successful industry leading StackWise technology which is a premium stacking architecture StackWise 480 has a stack bandwidth of 480 Gbps StackWise 480 uses Cisco IOS Software SSO for providing resiliency within the stack The stack behaves as a single switching unit that is managed by an active switch elected by the member switches The active switch automatically elects a standby switch within the stack The active switch creates and updates all the switching routing wireless information and constantly synchronizes that information with the standby switch If the active switch fails the standby switch assumes the role of the active switch and continues to the keep the stack operational Access points continue to remain connected during an active to standby switchover A working stack can accept new members or delete old ones without service interruption StackWise 480 creates a highly resilient single unified system of up to four switches providing simplified management using a single IP address single Telnet session single CLI auto version checking auto upgrading auto configuration and more StackWise 480 also enables local switching in Cisco Catalyst 3850 Series Switches Cisco StackPower Tec
43. or control plane and data plane traffic IPv6 ACLs can be applied to filter IPv6 traffic Port based ACLs for Layer 2 interfaces allow security policies to be applied on individual switch ports e Device access o o Secure Shell SSH Protocol Kerberos and Simple Network Management Protocol Version 3 SNMPv3 provide network security by encrypting administrator traffic during Telnet and SNMP sessions SSH Protocol Kerberos and the cryptographic version of SNMPv3 require a special cryptographic software image because of U S export restrictions TACACS and RADIUS authentication facilitates centralized control of the switch and restricts unauthorized users from altering the configuration Multilevel security on console access prevents unauthorized users from altering the switch configuration e Bridge protocol data unit BPDU Guard shuts down Spanning Tree PortFast enabled interfaces when BPDUS are received to avoid accidental topology loops 2013 Cisco and or its affiliates This document is Cisco Public Information Page 12 of 28 e Spanning Tree Root Guard STRG prevents edge devices not in the network administrator s control from becoming Spanning Tree Protocol root nodes e Wireless end to end security offers CAPWAP compliant DTLS encryption to make sure of encryption between access points and controllers across remote WAN LAN links Resiliency Borderless networks enable enterprise mobility and business grade vide
44. s Cisco has pioneered a host of rich capabilities such as high availability based on stateful switchover SSO on stacking granular QoS security and Flexible Netflow FNF across wired and wireless in a seamless fashion Also the wired plus wireless features are bundled into a single Cisco IOS Software image which reduces the number of software images that users have to qualify certify before enabling them in their network The single console port for command line interface CLI management reduces the number of touch points to manage for wired plus wireless services thereby reducing network complexity simplifying network operations and lowering the TCO to manage the infrastructure Converged wired plus wireless not only improves wireless bandwidth across the network but also the scale of wireless deployment Each 48 port Cisco Catalyst 3850 provides 40 Gbps of wireless throughput 20 Gbps on the 24 port model This wireless capacity increases with the number of members in the stack This makes sure that the network can scale with current wireless bandwidth requirements as dictated by IEEE 802 11n based access points and with future wireless standards such as IEEE 802 11ac Additionally the Cisco Catalyst 3850 distributes the wireless controller functions to achieve better scalability Each Cisco Catalyst 3850 switch stack can operate as the wireless controller in two modes e Mobility agent MA This is the default mode in which the Cisco Catal
45. to IP Services e license L C3850 24 S E Cisco Catalyst 3850 24 port IP Base to IP Services e license L C3850 48 S E Cisco Catalyst 3850 48 port IP Base to IP Services e license Access Point Licenses L LIC CT3850 UPG Primary upgrade license SKU for Cisco 3850 wireless controller e delivery L LIC CTIOS 1A 1 access point adder license for Cisco IOS Software based wireless controller e delivery LIC CT3850 UPG Primary upgrade license SKU for Cisco 3850 wireless controller paper license LIC CTIOS 1A 1 access point adder license for the Cisco IOS Software based wireless controller paper license Power Supplies and Fan for the Cisco Catalyst 3850 Series PWR C1 350WAC 350WAC power supply spare PWR C1 715WAC 715WAC power supply spare PWR C1 1100WAC 1100WAC power supply spare PWR C1 440WDC 440WDC power supply spare PWR C1 BLANK Power supply blank spare C3850 FAN T1 Fan module spare StackWise 480 and StackPower Cables for the Cisco Catalyst 3850 Series STACK T1 50CM Cisco StackWise 480 50cm stacking cable spare STACK T1 1M Cisco StackWise 480 1m stacking cable spare STACK T1 3M Cisco StackWise 480 3m stacking cable spare CAB SPWR 30CM Cisco Catalyst 3850 StackPower cable 30cm spare CAB SPWR 150CM Cisco Catalyst 3850 StackPower cable 150cm spare 2013 Cisco and or its affiliates This document is Cisco Public Information Page 27 of 28 Product Number Product Description Spare Power Cords for the Cisco Catalyst 3850 Series
46. ts_ device support tables list html Ajai CISCO Americas Headquarters Cisco Systems Inc San Jose CA Asia Pacific Headquarters Cisco Systems USA Pte Ltd Singapore Europe Headquarters Cisco Systems International BV Amsterdam The Netherlands Cisco has more than 200 offices worldwide Addresses phone numbers and fax numbers are listed on the Cisco Website at www cisco com go offices e not imply a partnership relationship between Cisco and any other company 1110R Printed in USA 2013 Cisco and or its affiliates This document is Cisco Public Information Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and or its affiliates in the U S and other countries To view a list of Cisco trademarks go to this URL www cisco com go trademarks Third party trademarks mentioned are the property of their respective owners The use of the word partner does C78 720918 00 01 13 Page 28 of 28
47. yst 3850 switch ships In this mode the switch is capable of terminating the CAPWAP tunnels from the access points and providing wireless connectivity to wireless clients Maintaining wireless client databases and configuring and enforcing security and QoS policies for wireless clients and access points can be enforced in this mode No additional license on top of IP Base is required to operate in the mobility agent mode e Mobility controller MC In this mode the Cisco Catalyst 3850 switch can perform all the mobility agent tasks in addition to mobility coordination radio resource management RRM and Cisco CleanAir coordination within a mobility subdomain The mobility controller mode can be enabled on the switch CLI IP Base license level is required when the Cisco Catalyst 3850 switch is acting as the mobility controller A centrally located Cisco 5508 Wireless LAN Controller WLC 5508 Cisco Wireless Services Module 2 WiSM2 when running AireOS Version 7 3 and Wireless LAN Controller 5760 can also perform this role for larger deployments With mobility agents located in the wiring closets providing 40 Gbps of wireless per switch n x 40 Gbps for a stack of n switches and mobility controllers managing some of the central wireless functions the converged access based wireless deployment provides best in class scalability for wireless and significantly improved wireless throughput 2013 Cisco and or its affiliates This document is Cis

Download Pdf Manuals

image

Related Search

Related Contents

Behringer DI4000 User's Manual  取扱説明書  STIGA PARK  User`s Manual USB Auto Share Switch  0-10V,1-5V,4-20mA  GUÍA DOCENTE  Philips M8881B  ATyS S/ Sd  Samsung ME32B Kasutusjuhend    

Copyright © All rights reserved.
Failed to retrieve file