Home

Smart FSSBID 100 flat panel floorstand

Contents

1. 1010651 Rev C1 1010651 Rev C1 32 MODEL FSSBID 100 CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET IMPORTANT Ensure that your SMART Board interactive display frame is functioning correctly before you install the rear access panels on your SMART Mobile Stand see page 58 Connect your SMART Mobile Stand temporarily to a power outlet while you check your interactive display frame Connecting Your SMART Board for Flat Panel Displays Interactive Overlay This section describes how to connect your SMART Board for Flat Panel Displays interactive overlay to your SMART Mobile Stand instead of directly to a computer Refer to the SMART Board for Flat Panel Displays Installation Guide Corner Brackets smarttehc com kb 000769 for general instructions on installing your interactive overlay on your flat panel display IMPORTANT You need adapter ADO9 to install your SMART Board for Flat Panel Displays interactive overlay Purchase this adapter Part No ADP USB AB from your authorized SMART reseller lt o d HH USB A Female to USB B Female Adapter AD09 33 MODEL FSSBID 100 CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET Cable Connections to Your Interactive Overlay Coil the DB9 to USB adapter cable s excess length fasten it to a clip on the speaker panel with a plastic cable
2. Cy 1010651 Rev C1 71 CONFIGURING A RACK MOUNT 4 Remove the two installed shelves from the cabinet and then remove the eight shelf clips os ed 5 Locate the cabinet s rear support tube remove the two screws in the flange at the top and then lift the tube at a slight angle to detach and remove it from the base of the unit ch Mali E Rear Support Tube A NOTE You may need to detach some cables to remove this support tube After you finish configuring your SMART Mobile Stand to accommodate a rack mount attach these cables again 1010651 Rev C1 72 CONFIGURING A RACK MOUNT To configure a 1 Open the doors of your SMART Mobile Stand s cabinet rack mount Locate the left and right front rack rails and then remove the two screws in the flange at the top of each rail Keep these screws nearby Left Rack Rail Right Rack Rail D 1010651 Rev C1 73 CONFIGURING A RACK MOUNT 3 Lift the left rack rail at a slight angle to detach it from the base rotate it 90 clockwise and then insert the rail at a slight angle into the rack
3. Three USB A Male Plugs RJ45 Male Plug Marked C01 C02 and C03 Marked N01 Prewired to Your SMART Mobile Stand s Prewired to Your SMART Mobile Stand s Connection Panel Connection Panel 1010651 Rev C1 To connect to your computer 1010651 Rev C1 22 Ts 4 MODEL FSSBID 100 CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET Connect the VGA video plug from cable AV01 in the prewired cable harness to your computer s VGA video receptacle fg NOTES Your computer might have more than one VGA video receptacle If this is the case refer to the documentation included with your computer to determine the correct receptacle f your computer has only DVI receptacles you likely received a DVI to VGA adapter or video card with your computer which enables you to use the DVI connection If you require a DVI to VGA adapter you can purchase one from an electronics or computer store Connect the 3 5 mm stereo audio plug from cable AV01 in the prewired cable harness to your computer s audio output receptacle m NOTES This audio receptacle is typically green and is often marked with an insert arrow or the audio waves symbol gt gt If you re unable to locate this receptacle refer to the documentation included with your computer for more information You previously connected the other end of this cable to your flat panel display see page 19 Connect each of the three USB
4. 1 Working inside your SMART Mobile Stand s cabinet from the back secure your interactive overlay s power supply to the two mounting holes directly to the right of the connection panel using plastic cable ties IMPORTANT Position this power supply so that the power cable is on the left side 2 Connect the power cable and connector from this power supply to your interactive overlay s power port TIPS Route this power cable through your SMART Mobile Stand s connection panel and up the prewired cable harness Leave some slack throughout the length of this cable Don t pull it tight 1010651 Rev C1 1010651 Rev C1 56 3 MODEL FSSBID 100H CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET Connect the DB9 end of the SMART DB9 to USB adapter cable included with your SMART Board for Flat Panel Displays interactive overlay to your pen tray fj NOTE You already connected the other end of this cable to your SMART Hub SE240 page 43 A TIP Route this adapter cable through your SMART Mobile Stand s connection panel and up the prewired cable harness leaving some slack throughout the length ofit Loosen the hook and loop fastener strap securing cables below the connection panel coil the DB9 to USB adapter cable s excess length and then secure it together with the rest of the cables with the hook and loop fastener strap 4 Connect your interactive overlay s power cab
5. OR Cables C01 C02 and C03 Cable C04 Cable V03 USB A Male Plugs USB B Male Plug DVI Male Connector To Your SMART Hub SE240 To Your SMART Hub SE240 To Your SMART Hub SE240 SII 22 HES S Video Male Connector Cable V02 S Video Male Connector To Your SMART Hub SE240 To Device One e g DVD Blu ray Player jam 1215 NIG Cable V04 VGA Male Connector DVI Male Connector To Your Flat Panel Display To Your SMART Hub SE240 Appendix C Hardware Environmental Compliance SMART Technologies supports global efforts to ensure that electronic equipment is manufactured sold and disposed of in a safe and environmentally friendly manner Waste Electrical and Electronic Equipment Regulations WEEE Directive Waste Electrical and Electronic Equipment regulations apply to all electrical and electronic equipment sold within the European Union When you dispose of any electrical or electronic equipment including SMART Technologies products we strongly encourage you to properly recycle the electronic product when it has reached end of its life If you require further information please contact your reseller or SM
6. 4x tet H NOTE Don t over tighten these screws 6 Replace the shelves that you removed in step 1 g TIPS Ensure that you leave at least 1 2 5 cm of space between equipment for cooling Formore information on adjusting the shelves in your SMART Mobile Stand s cabinet see page 14 41 MODEL FSSBID 100H CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET Connecting Your Flat Panel Display Follow these instructions to connect the correct cables from your FSSBID 100H s prewired cable harness to your flat panel display s connection panel Cable Connections to Your Flat Panel Display Speaker VGA 3 5 mm Stereo Cable Video In Audio In Receptacles from Your from Your Output to SMART SMART Hub Prewired Hub Speakers ACIN SP JACKS VGA AUDIO OU 79 Go gi ong Speaker 3 5mm Cables Stereo A02 VGA Audio and Cable Cable A03 V04 A04 amp S 9 e o lt amp C C C 2 s s 3 x Me A A ORS lt lt SS x x a e S S KD 49 1010651 Rev C1 To connect your flat panel display 1010651 Rev C1 42 MODEL FSSBID 100H CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET 1 Connect speaker cables A02 and A03 to your flat panel display s speak
7. The Connection Panel The audiovisual connection panel on the back of your SMART Mobile Stand enables you to connect your computer to your flat panel display This panel also makes it easy for you to connect guest laptop computers your SMART Document Camera your SMART Response formerly Senteo interactive response system receiver and other USB devices When you want to move your SMART Mobile Stand you can easily disconnect cables from this panel See starting on page 61 for details about connecting a guest laptop computer or other SMART products to your unit A NOTES You must connect your SMART Mobile Stand to a computer or a SMART Hub to use all the features of the connection panel You already connected both ends of the included 6 2 m USB A male to USB B male cable marked C05 to your SMART Mobile Stand s connection panel as instructed in the SMART Mobile Stand for Interactive Displays Textless Installation Instructions smarttech com kb 132293 This external cable isn t part of your SMART Mobile Stand s prewired cable harness The rear connection panel includes the following inputs VGA video 3 5mm stereo audio e Two FSSBID 100 or three FSSBID 100H USB A connections for external devices One USB A FSSBID 100 only and one USB B connection for interactive display control Cat5e RJ45 network connection point requires a computer 1010651 Rev C1 60 COMPLETING YOUR INSTALLATION AND CONNEC
8. a Composite A01 Computer Audio SMART Hub SE240 Cable V04 Stereo Audio Cable AV05 3 3 5mm 8 si exi lt i z x Q Tm umi 8 o me L kau IEEE as o O m o og om 1 238B i E SEM I s feat m CT Q 559 Koj S was ae lo m FA S 28 Meli Vie tU UU ga s 8 ES ag OC m JE SE L By 3 5 fa O SEE guna ill I 1010651 Rev C1 44 MODEL FSSBID 100H CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET Perform the following procedure to connect a SMART Hub SE240 to your SMART Mobile Stand A NOTE You reguire a USB A to USB B cable not included if you re installing a computer with your SMART Hub SE240 To connect your 1 Connect the 3 5 stereo audio plug from cable A01 to your SMART Hub s SMART Hub SE240 Computer Audio receptacle marked 1 2 Connect the three plug RCA cable AVO2 included in your SMART Mobile Stand s accessory kit as follows Connect the yellow plug to your SMART Hub s Composite Video RCA receptacle Connect the red
9. lt SF CP 8 S P5 KS A OF OE SV o S lt 9 Qq e 2 SY gt A Q So Cg 9 Kata lt 9 lt A ST SLSR lt o 2 S S x SON S S 5 x K d s K ON N Oo CO C S S e Y QE SR S YS va lt 5 3 SOS SN x AN v KO 49 1010651 Rev C1 To connect your flat panel display 19 1 MODEL FSSBID 100 CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET Connect speaker cables A02 and A03 to your flat panel display s speaker receptacles Connect the VGA video plug from cable AV01 to your flat panel display s VGA video receptacle F NOTE If your flat panel display has more than one VGA video receptacle use the receptacle adjacent or closest to a 3 5 mm audio receptacle Connect the 3 5 mm stereo audio plug from cable AV01 to an audio receptacle on your flat panel display s connection panel Typically this audio receptacle is beside the VGA connection Connect the 3 5 mm stereo audio plug from cable A01 to a second audio receptacle on your flat panel display s connection panel A NOTE If your flat panel display s connection panel has only one 3 5 mm audio receptacle contact your authorized SMART reseller to purchase a 3 5 mm audio Y adapter cable Connect cable V01 as follows Connect the red BNC plug to the red BNC receptacle on your flat panel display s connection panel This receptacle is typically labeled R
10. Connect the green BNC plug to the green BNC receptacle on your flat panel display s connection panel This receptacle is typically labeled G Connect the blue BNC plug to the blue BNC receptacle on your flat panel display s connection panel This receptacle is typically labeled B Connect the white BNC plug to the white BNC receptacle on your flat panel display s connection panel This receptacle is typically labeled H Connect the yellow BNC plug to the yellow BNC receptacle on your flat panel display s connection panel This receptacle is typically labeled V Connect cable AVO2 as follows Connect the yellow plug to the yellow RCA receptacle on your flat panel display s connection panel This receptacle is typically labeled V or VIDEO Connect the red plug to the adjacent red RCA receptacle on your flat panel display s connection panel This receptacle is typically labeled R Connect the white plug to the adjacent white RCA receptacle on your flat panel display s connection panel This receptacle is typically labeled L 1010651 Rev C1 1010651 Rev C1 20 MODEL FSSBID 100 CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET Connect cable AV03 as follows Connect the RGB red video plug to the appropriate red RCA receptacle on your flat panel display s connection panel This receptacle is typically labeled Pr or R IMPORTANT Do not confuse the RGB red video plug with the red audio
11. see pag 13 To prevent damage to your power and extender cables secure them to your mobile floor stand as instructed in the SMART Mobile Stand for Interactive Displays Textless Installation Instructions smarttech com kb 32293 To prevent crushing additional product cables between your flat panel display and the SMART Mobile Stand s speaker panel follow the path of the installed cable harness Do not suspend additional objects from or add any extra weight or excessive pressure to your SMART Mobile Stand s brackets other than the products indicated in this guide SMART designed these brackets to support only the combined weight of a flat panel display interactive overlay or display frame laptop computer and optional laptop shelf during normal use Any other weight hung from these brackets may cause the stand to tip If you install additional audio or video cables other than those provided with your SMART Mobile Stand SMART Board interactive display frame SMART Board for Flat Panel Displays interactive overlay or as part of an adapter kit SMART assumes no responsibility and you are solely responsible for any damage incurred to your SMART Mobile Stand its cabling or other devices Your SMART Mobile Stand is designed for standard ramp access At least two people are required to move your unit up or down a ramp Moving your unit up or down a ramp with a steep incline may cause your SMART Mobile Stand to tip Never operate yo
12. 100H 100H AD05 AC Y IEC Male N A Various e e to Country Specific Female AD06 Power Bar P01 IEC Male to NEMA N A 93 00700 20 e e AD07 P04 Interactive IEC Male N A Various e e Overlay or to Country Specific Female Interactive Display Frame AD08 AV05 SMART Hub VGA Female to DVI A Male N A 93 00528 20 e e SE240 AD09 C04 Interactive USB B Female N A 93 00698 20 lO IO Overlay s to USB A Female USB to Serial Adapter Power P01 AD06 or Flat Panel IEC C14 to IEC C13 13 4m 93 00705 20 e e e e P02 Display P02 IEC NEMA P01 or IEC C14 3 91 cm 93 00693 20 e e Power Bar SE240 to Two Plug IEC C13 Y P03 Power Bar NEMA Male to Three Way 2 60 cm 93 00691 20 e e NEMA Female P04 Power Bar AD04 and IEC C14 N A 93 00706 20 e e AD05 to Two Plug IEC C13 Y P06 AC Mains IEC Power Country Specific to IEC C13 8 2 4 m Various e e Bar Power Distribution NEMA NEMA AC Power 93 00690 20 e e Distribution Strip IEC IEC AC Power 93 00692 20 e e Distribution Strip See page 82 for country specific power adapters 1010651 Rev C1 1010651 Rev C1 82 SMART MOBILE STAND RUNNING DIAGRAMS Country Specific Power Adapters Country SMART Adapter Part No Australia 93 00587 20 Bahrain 93 00586 20 China 93 00707 20 Finland 93 00584 20 France 93 00584 20 Germany 93 00584 20 Iran 93 00584 20 Iraq 93 00586 20 Japan 93 00606 20 Korea 93 00584
13. Customer Support Online Information and Support Visit smarttech com support to view and download user s guides how to and troubleshooting articles software and more Training Visit smarttech com trainingcenter for training materials and information about our training services Technical Support If you experience difficulty with your SMART product please contact your local reseller before contacting SMART Technical Support Your local reseller can resolve most issues without delay A NOTE To locate your local reseller visit smarttech com where Warranty Product warranty is governed by the terms and conditions of SMART s Limited Eguipment Warranty that shipped with the SMART product at the time of purchase Registration To help us serve you register online at smarttech com registration 1010651 Rev C1 88 CUSTOMER SUPPORT 1010651 Rev C1 Index A accessories 8 adapter kit 8 adjusting shelving 14 assembly 9 11 12 quality 10 audio 2 B Blu ray player 25 48 connecting 26 48 HDMI cable not included 25 48 installation 25 48 C cable graphics model FSSBID 100 83 model FSSBID 100H 84 cable harness 17 safety 12 cable management 2 Chinese regulations 86 cleaning 67 clevis pin 13 computer 7 21 46 connecting 22 47 laptop 67 USB hub reguired 22 connecting laptop 67 Senteo interactive response system 64 SMART Document Camera 63 SMART Hub PE260 23
14. EN55022 CISPR 22 Class B Flammability Rating Plastics HB USB 2 0 cable UL VW 1 CSA FT4 Quality Assembly USB cable IPC WHMA A 620 Class 2 workmanship standards for Requirements amp Acceptance for Cable amp Wire Harness 11 ASSEMBLING YOUR SMART MOBILE STAND Things to Consider When Assembling Your SMART Mobile Stand F3 WARNING Two people are required to safely assemble your SMART Mobile Stand and to mount or remove your flat panel display and your SMART Board interactive display frame or SMART Board for Flat Panel Displays interactive overlay Lock the casters before installing or working with your flat panel display on your SMART Mobile Stand or adjusting its height To prevent injury be aware of crush and pinch locations on the product marked with the crush symbol during assembly and use Do not rest your hand on the stand s universal mount or under the interactive product s pen tray or pencil ledge while adjusting the height of your SMART Mobile Stand Use the SMART Mobile Stand s three grab bars to move the unit Do not press pull or push on the flat panel display interactive overlay or display frame cabinet doors rear access panel plastics or vertical brackets Before moving your SMART Mobile Stand make sure that you unlock the casters These casters are designed to roll on common indoor surfaces While you move the unit your view may be partially obstructed Be aware of
15. 100 CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET Connecting Your Flat Panel Display Follow these instructions to connect the correct cables from your FSSBID 100 s prewired cable harness to your flat panel display s connection panel Cable Connections to Your Flat Panel Display Speaker 3 5 mm Stereo BNC Connections Stereo Audio Stereo Audio Cable Audio In from for RGB HV Video and and RGB or Receptacles Your Computer Input from the Composite Component Output to Connection Panel Video RCA Video RCA Prewired VGA 3 5 mm Stereo Inputs from Inputs from Speakers Video In Audio In an External an External from Your from the Device Device e g Computer Connection Panel e g VCR DVD Player ACIN TS AUI AUTIO co IN pm 559 or ES EE 60 0990 4 Sd PEt 11 g nnn A n k Wc C HI j E ET Speaker A 3 5mm 3 5mm Cables VGA Stereo Stereo 5 x BNC A02 Cable Audio Audio RGB HV he ius So on and AVO1 Cable Cable Cable V01 RE ne A03 Avor A01 I lI l 3 RY amp amp Q Q d amp AW zo 9 3
16. A male plugs from cables C01 C02 and C03 in the prewired cable harness to an available USB receptacle on your computer OR If your computer has only two available USB receptacles connect the A male plug from the USB cable marked C01 to one receptacle connect a USB hub not included to the second receptacle and then connect the A male plugs from the USB cables marked C02 and C03 to the USB hub OR If your computer has only one available USB receptacle connect a USB hub not included to the receptacle and then connect all three USB A male plugs to the USB hub A NOTE If you require a USB hub to connect cables C01 C02 and C03 to your computer your authorized SMART reseller can recommend a part Connect RJ45 cable N01 to your computer s network LAN receptacle To connect your SMART Mobile Stand to a SMART Hub PE260 23 MODEL FSSBID 100 CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET 5 Connect your computer s power cable not included with your SMART Mobile Stand to an available receptacle on your stand s power bar g TIP Coil and bundle the cable with the included hook and loop fastener strap Connecting Your SMART Hub PE260 If you connect your SMART Mobile Stand to a SMART Hub PE260 instead of a computer install your SMART Hub PE260 in the dedicated space for a tower computer behind the left cabinet door when your stand is configured for standard shelving For more information about usi
17. A plug at the other end g TIPS First route this adapter cable through your SMART Mobile Stand s connection panel and up the prewired cable harness Leave some slack throughout the length of this cable Don t pull it tight Coil the excess cable and fasten it to the lower right clip on your SMART Mobile Stand s speaker panel with plastic cable ties 4 Connect the USB plug that you left accessible in the previous step to the USB A receptacle of adapter AD09 which you purchased for your SMART Mobile Stand as shown on page 32 A NOTE Don t connect the SMART DB9 to USB adapter cable included with your SMART Board for Flat Panel Displays interactive overlay to your computer as instructed in the SMART Board for Flat Panel Displays Installation Guide 5 lfyou ve connected either a computer or a SMART Hub PE260 to your SMART Mobile Stand remove the plastic cable tie from the USB B male cable marked C04 in re your SMART Mobile Stand s prewired cable harness and v then connect it to the other end of the adapter that you purchased for your unit as shown on page 32 m NOTE The other end of cable C04 is prewired to your SMART Mobile Stand s connection panel g TIP Secure cable C04 to the SMART DB9 to USB adapter cable included with your interactive overlay with a plastic cable tie USB B Cable C04 6 Connect your interactive overlay s power cable included
18. Flat Panel Displays interactive overlay or as part of an adapter kit SMART assumes no responsibility and you are solely responsible for any damage incurred to your SMART Mobile Stand its cabling or other devices IMPORTANT The following procedures are generic instructions and your DVD or Blu ray player or VCR s connection panel might not resemble the illustrations or color codes referenced in this guide Refer to the documentation included with your device for specific connection instructions Forsome DVD and Blu ray players you might choose to purchase a separate HDMI cable to replace cable AV03 Install this HDMI cable along the same path as cable AV03 See page 12 for details on connecting the other end of this cable to your flat panel display TIPS Install your DVD or Blu ray player on the top shelf or highest rack mount position in your SMART Mobile Stand s cabinet Install your VCR on the lowest shelf in your SMART Mobile Stand s cabinet 1010651 Rev C1 26 MODEL FSSBID 100 CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET To connect your 1 Connect the five plug RCA cable AV03 or your DVD Blu ray player HDMI cable as follows Connect the RGB red video plug to your DVD or Blu ray player s appropriate red receptacle which is typically labeled Pr or R 6 IMPORTANT Do not confuse the RGB red video plug with the red audio plug Connect the RGB blue video plug to your DVD or
19. Mobile Stand page 12 Securing the Clevis Pins When Installing a 60 152 cm or Larger Flat Panel Display page 13 e Adjusting the Shelves page 14 1010651 Rev C1 1010651 Rev C1 10 ASSEMBLING YOUR SMART MOBILE STAND Environmental Requirements Before installing your SMART Mobile Stand refer to the following environmental requirements CAUTION e Never operate your SMART Mobile Stand immediately after moving it from a cold location to a warm location Allow the unit to reach room temperature before operation to prevent possible product damage Do not place your SMART Mobile Stand in hot locations such as near heating equipment Do not block the ventilation slots and openings on your SMART Mobile Stand Blocking these openings could cause overheating and damage to the unit Environmental Requirement Parameter Operating Temperature 41 F to 86 F 5 C to 30 C Storage Temperature Humidity 40 F to 140 F 40 C to 60 C 5 80 relative humidity non condensing Water and Fluid Resistance Intended for indoor use Don t pour or spray liquids directly on the electronic components Dust Moderate dust Designed for pollution degree 1 P1 as per EN61558 1 which is defined as No pollution or only dry non conductive pollution Refer to page 67 for instructions on periodically cleaning your SMART Mobile Stand Conducted and Radiated Emissions
20. SMART Hub SE240 43 connection panel 59 illustration 60 connections laptop 67 Consumer Product Safety Improvement Act 86 contact information 87 covered electronic devices 86 customer support 87 D documentation 87 dust 70 DVD player 25 48 connecting 26 48 installation 25 48 E EIP regulations 86 emissions 10 environment dust 10 emissions 10 humidity 70 environmental compliance See hardware environmental compliance European Union regulations 85 features 2 finish 2 flammability 10 flat panel adapter kit 8 1010651 Rev C1 1010651 Rev C1 90 INDEX flat panel display 65 13 connections 17 18 19 41 42 flat panel displays supported 7 fluid resistance 10 G general inquiries 87 H hardware Z hardware environmental compliance 85 86 HDMI cable 25 48 height adjustment 2 inquiries 87 installation 9 17 12 13 rear access panels 58 integration 59 K keyboard 66 L laptop computer connecting 67 laptop shelf 8 Limited Equipment Warranty 87 M maintenance 67 mobility 2 68 mouse 66 N network 7 O online support 87 p packaging 68 85 power management 2 power specifications Z 60 product features 2 product integration 59 Q quality 10 R rack mount configuring 69 rack mount hardware accessory kit 8 69 rear access panels 58 installing 58 removing 70 registration 87 regula
21. USB A male plugs from cables C01 C02 and C03 in the prewired cable harness inside the cabinet of your SMART Mobile Stand to an available USB A receptacle on your SMART Hub marked USB Remove the plastic cable tie from the USB B male cable marked C04 in your SMART Mobile Stand s prewired cable harness and then connect this cable to the USB B receptacle marked Computer 1 on your SMART Hub SE240 If you intend to install a SMART Board interactive display frame on your SMART Mobile Stand connect the USB A plug of the USB cable included with your interactive display frame to an available USB A receptacle on your SMART Hub SE240 OR If you intend to install a SMART Board for Flat Panel Displays interactive overlay with your SMART Mobile Stand connect the USB A plug of the SMART DB9 to USB adapter cable included with your interactive overlay to an available USB A receptacle on your SMART Hub SE240 g TIP Route the other end of this cable up the cabinet s rear support tube and behind the hydraulic pump Connect RJ45 cable N01 to your SMART Hub s network LAN receptacle marked Network If you re installing a computer with your SMART Hub SE240 complete the following steps Otherwise see To finish installing your SMART Hub SE240 on page 45 1 Connect the DVI A connector of adapter ADO8 included with your SMART Hub SE240 to your SMART Hub s remaining Video In receptacle marked Computer 2 and then connect the VGA vide
22. ZON oipny A oipny 1 9 1u uoduioo g u uodwog M jusuoduuod 0AV eldsiq jaued JE PleogaylyMm eAnoeJejur sAejdsig jaueg J8 104 pieog LHYNS jjejsui nof ji Buum 2 89IpPUI seui PaUIJEH aloN Hi Z0av vod O IV Tod vod O 9v u ov 3 As OW TON Nym 05 a asn v asn 75 vasn vasn 99 98 AV vOAV dojde sawojsng o TOA V9 yoAV TOAV Jeueg uonoeuuoo ul gsn ul gsn MIOMJON LOO LON suleW OV gog SCH 8sn roay gt No oe eiS Tony PO VOA Jejndulo9 Jewojsna sue OV nav ino olpny 4 OV jno OIPNY 1 ul OV MO ltsoduoo dvl c OV ZOAV YOA 59 om lA 9q 1euojsno SUle OV U OV 999 90d MO olpny A zog o OV MO olpny 1 Pod MO OV 9 juauoduod av no ov g juauoduuod av no ov ON Y 1u uoduioo ay ino ov Jakeld GAq e euo vaq Jeauojsna Jeg Jewod 1010651 Rev C1 SMART MOBILE STAND RUNNING DIAGRAMS 78 ional FSSBID 100H Internat Jeydepy 00 0V ul oq ul jeues kel u q eyeAQ 249819 U u asnje gsn Jaydepy lenes 0 SN sue OV nO Od Jejdepy Od OV ul od ul asn asn JejoJjuo2 sues ejdsig eAnoeJeju sjeyeedg gt j MO 08191 polmald OL a l3inooeims SU OV 0812 S LUU G E ul VDA 0 kejdsig jeued JE Pieogajlym aAga8eJ9jul s ejdsig Jeueq e 3 104 pleog LYVWS Ilelsui NOA Ji 1no ov Buum ejeoipui seui peuojeH alON Hi uA OW NVWN
23. plug Connect the RGB green video plug to the green RCA receptacle on your flat panel display s connection panel This receptacle is typically labeled Pb or B Connect the RGB blue video plug to the blue RCA receptacle on your flat panel display s connection panel This receptacle is typically labeled YorG Connect the red audio plug to the remaining red RCA receptacle on your flat panel display s connection panel This receptacle is typically labeled R Connect the white audio plug to the remaining white RCA receptacle on your flat panel display s connection panel This receptacle is typically labeled L Connect your SMART Mobile Stand s prewired power cable to your flat panel display s power receptacle Connect the other end of this cable to an available receptacle on your SMART Mobile Stand s power bar IMPORTANT Your flat panel display won t look exactly like the one shown on page 18 Some flat panel displays require audio video adapters which you can purchase from your authorized SMART reseller If you intend to install a Blu ray player you can purchase a separate HDMI cable to replace cable AVO3 Install this HDMI cable along the same path as cable AV03 and then connect it to similar points NOTE Don t connect your SMART Mobile Stand to a power outlet before you install the rear access panels page 58 21 MODEL FSSBID 100 CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET Connecti
24. plug to the adjacent Audio In RCA receptacle marked R Connect the white plug to the adjacent Audio In RCA receptacle marked L 3 Connect the two plug RCA cable A04 as follows Connect the red plug to your SMART Hub s Audio Out RCA receptacle marked R Connect the white plug to your SMART Hub s Audio Out RCA receptacle marked L A NOTE You previously connected the other end of this cable to your flat panel display see page 42 4 Connect the two plug RCA cable A05 included in your SMART Mobile Stand s accessory kit as follows Connect the red audio plug to your SMART Hub s remaining Audio In RCA receptacle marked R Connect the white audio plug to your SMART Hub s remaining Audio In RCA receptacle marked L 5 Connect S Video cable V02 included in your SMART Mobile Stand s accessory kit to your hub s S Video receptacle 6 Connect DVI cable V03 in the prewired cable harness inside the cabinet of your SMART Mobile Stand to your hub s Video In receptacle marked Computer 1 7 Connect DVI cable V04 to your SMART Hub s DVI receptacle marked Video Out A NOTE You previously connected the other end of this cable to your flat panel display see page 42 1010651 Rev C1 To connect your SMART Hub SE240 to a computer To finish installing your SMART Hub SE240 45 10 11 MODEL FSSBID 100H CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET Connect each of the three
25. the base of a SMART Hub SE240 mounting bracket to the top of the front left corner and rear right corner of your hub when viewed from its connection face as shown in the following image 39 MODEL FSSBID 100H CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET 3 Using a Phillips No 2 screwdriver secure these mounting brackets using four of the screws included with your SMART Hub SE240 as shown m NOTE You don t need the other two L brackets and four screws included with your hub 4 Working inside your SMART Mobile Stand s cabinet from the rear position your SMART Hub SE240 against the cabinet s top panel aligning the holes in the mounting brackets to the four pilot holes drilled in the top of the cabinet as shown CA ei A pi a Pilot Holes Drilled in Cabinet s E Top Panel 1010651 Rev C1 1010651 Rev C1 40 MODEL FSSBID 100H CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET 5 Using a Phillips No 2 screwdriver secure your SMART Hub SE240 to your SMART Mobile Stand s cabinet with the four washers and four screws included in your stand s accessory kit as shown A es i Vi
26. ul 2d sule OV Jejdepy ui 8Sn 5 TON pHOMION BIJ9S o u Jeues 0 SN 1 8SN 705 Siqeo gsn wong V SSN u 1asn 05 SOAY jno oeJeis Jejndujo asn z 1einduio 4 Sony MO VOA d Z olpny Jejndujo Tov Jejnduo9 Jawojsna Jojde 1depY Od OV u OAPIA Z JajnduoD C0A Sule OV dVL OV gsn Jajnduog 9 g 2 gsn JewojsnD mo lisoduioo olpny Jejnduog ZOAV ul asn SOAV ano oipny s aqe ASN ul o9piA p 1anduio2 e 20AV Jejj onuo uue1j Aejdsiq eAnoeJeju sodv SOAV sony ino opnv 3 oipny s ZOAV MDA Bre om asnaq 1euoisno si ye ds u NO o i ls oipny 1 ZOAV PIIM O qmo 0212 OBPIA ojisoduo9 ZON Sule OV SUIEN OV olpny A MO OBPIA S sov TOA 08191S WW G g oipny 1 Sov Sov O 9IPnv i O pIA S 1nO oipny 1 Ul VOA ZOA SOV e dsiq jeued e 4 O0yZJS ANH yews Je e d GA B 9 auo SIA q Jeuojsn2 deg 12MOd 1010651 Rev C1 SMART MOBILE STAND RUNNING DIAGRAMS 77 FSSBID 100 International Jejdepy Od OV u oa u jeues KEJ u q e u AO eAnoeloeju mo ZEZSU h Jejdepy 600V ienas 0 asn SUN OV Og mo od Jeydepy Od OV ul od ul ISA 900 JO OJJUOD euieJ4 Aejdsiq Al 9eJ1 1ul sule OV Tod Joyeods yry kav M Ino oipny seyeads yor kav ino oipny AV Molex LOA H euum LOA 9 jueuoduio USO TON anid LOA Pad LOA g juduoduo9 A 1u suoduioo o 1 s Jajndulo9 VOA Jainduo9 oipny A oipny 1 OBpIA ltsoduuoo
27. you previously connected to your SMART Hub SE240 page 43 VGA Video Male Cable 3 5 mm Stereo Audio Plug USB A Male Plug from USB A to USB B Cable Not Included A NOTE The VGA male cable and the 3 5 mm stereo audio cable are joined and marked AV05 To connect to your computer 47 1 MODEL FSSBID 100H CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET Connect the VGA video plug from cable AV05 to your computer s VGA video receptacle gg NOTES Your computer might have more than one VGA video receptacle If this is the case refer to the documentation included with your computer to determine the correct receptacle f your computer has only DVI receptacles you likely received a DVI to VGA adapter or video card with your computer which enables you to use the DVI connection If you require a DVI to VGA adapter you can usually purchase one from an electronics or computer store You previously connected the other end of this cable to your SMART Hub SE240 see page 45 Connect the 3 5 mm stereo audio plug from cable AV05 to your computer s audio output receptacle A NOTE This audio receptacle is typically green and is often marked with an insert arrow or the audio waves symbol If you re unable to locate this receptacle refer to the documentation included with your computer for more information Connect the
28. your SMART Response receiver over longer distances if you minimize interference signal reflections and the number and size of objects between your receiver and the clickers 1 Position your SMART Response receiver in an unobtrusive location away from other wireless products such as 2 4 GHz routers and cordless telephones For temporary installations place the receiver inside or on top of your SMART Mobile Stand s cabinet For permanent installations you can secure the receiver to the stand with two screws not included Orient the receiver with the long side or edge facing the class as shown IMPORTANT If you installed a SMART Board for Flat Panel Displays interactive overlay on your SMART Mobile Stand Position the outside edge of your receiver no more than 6 15 cm from the speaker panels so that you don t damage the receiver when you lower your interactive overlay OR Insert the included clevis pins as described on page 13 to prevent your SMART Mobile Stand from reaching its lowest position 65 COMPLETING YOUR INSTALLATION AND CONNECTING OTHER PRODUCTS TO YOUR SMART MOBILE STAND 2 Connect your receiver s captive USB cable connector to either of the adjacent vertical USB A connections marked USB or the USB receptacle marked with an image of a tower computer FSSBID 100H only on your SMART Mobile Stand s connection panel see page 60 or to an available USB receptacle on your com
29. your authorized SMART reseller This chapter covers Installing Your SMART Hub SE240 page 38 e Connecting Your Flat Panel Display page 41 Connecting Your SMART Hub SE240 page 43 Connecting Your Computer page 46 e Connecting a DVD Blu ray Player or VCR page 48 e Connecting Your SMART Board interactive display frame page 50 Connecting Your SMART Board for Flat Panel Displays Interactive Overlay page 55 1010651 Rev C1 To install your SMART Hub SE240 1010651 Rev C1 38 MODEL FSSBID 100H CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET Installing Your SMART Hub SE240 Perform the following procedure to install a SMART Hub SE240 in your FSSBID 100H s cabinet using the washers and screws that you received with your stand IMPORTANT Do not follow the installation instructions included with your SMART Hub SE240 When you configure your SMART Mobile Stand for a rack mount you can also install your SMART Hub SE240 in the top rack mount position see Configuring a Rack Mount on page 69 1 If the shelves are already installed in your SMART Mobile Stand remove them from the cabinet and then remove the eight shelf clips A NOTE If you need instructions for removing your rear access panels see steps 1 to 3 in Appendix A Configuring a Rack Mount on page 69 2 Align
30. 20 Netherlands 93 00584 20 Norway 93 00584 20 Oman 93 00586 20 Spain 93 00584 20 United Arab Emirates 93 00586 20 United Kingdom 93 00586 20 83 SMART MOBILE STAND RUNNING DIAGRAMS FSSBID 100 Cable Graphics Cable A01 Cables A02 and A03 3 5 mm Stereo Audio Plug Speaker Wires To the Connection Panel To Your Flat Panel Display c 3 5 mm Stereo Audio Plug Cable AVO1 3 5 mm Stereo Audio Plug T T VGA Video Male Connector VGA Video Male Connector To Your Flat Panel Display To Your Computer or SMART Hub PE260 m ME LUN a mm D H H Con mm o Pm pu 3 x RCA Plugs Cable AVO2 3 x RCA Plugs To Your Flat Panel Display To Device Two e g VCR m 05 iN LE DUMP IS S mm kino ui 5 x RCA Plugs Cable AV03 5 x RCA Plugs To Your Flat Panel Display To Device One e g DVD Blu ray Player Cables C01 C02 and C03 Cable C04 USB A Male Plugs USB B Male Plug To Your Computer or SMART Hub PE260 To Your Interactive Display Frame or ADO9 ET Ad
31. ART Mobile Stand s 1010651 Rev C1 serial number 68 MAINTAINING YOUR SMART MOBILE STAND Moving Your SMART Mobile Stand Your SMART Mobile Stand rolls easily on common indoor surfaces If you experience any problems with devices shifting in the cabinet while you move your unit use adhesive hook and loop fastener or two sided tape not included to secure the equipment If you move your SMART Mobile Stand with a SMART Board for Flat Panel Displays interactive overlay installed secure the pens in the pen tray so that they don t fall out Transporting Your SMART Mobile Stand Save your original SMART Mobile Stand packaging so that it s available if you need to transport your unit When required repack your SMART Mobile Stand with as much of the original packaging as possible This packaging was designed with optimal shock and vibration protection If your original packaging is no longer available you may purchase replacement packaging from your authorized SMART reseller If you prefer to use your own packaging materials make sure that you adequately protect the unit Ship your SMART Mobile Stand in an upright position to discourage shippers from placing heavy objects on it Contacting SMART Technical Support See Customer Support on page 87 for information on contacting SMART Technical Support Before contacting SMART Technical Support make note of your SMART Mobile Stand s serial number and then note it in the insid
32. ART Technologies for information on which recycling agency to contact Restriction of Certain Hazardous Substances ROHS Directive This product meets the requirements of the European Union s Restriction of Certain Hazardous Substances RoHS Directive 2002 95 EC Consequently this product also complies with other regulations that have arisen in various geographical areas and that reference the European Union s RoHS directive Packaging Many countries have regulations restricting the use of certain heavy metals in product packaging The packaging used by SMART Technologies to ship products complies with applicable packaging laws 1010651 Rev C1 1010651 Rev C1 86 HARDWARE ENVIRONMENTAL COMPLIANCE Covered Electronics Devices Many U S states classify monitors as Covered Electronic Devices and regulate their disposal Applicable SMART Technologies products meet the reguirements of the Covered Electronic Devices regulations China s Electronic Information Products Regulations China regulates products that are classified as EIP Electronic Information Products SMART Technologies products fall under this classification and meet the requirements for China s EIP regulations U S Consumer Product Safety Improvement Act The United States has enacted the Consumer Product Safety Improvement Act which limits the lead Pb content in products SMART Technologies is committed to complying with this initiative Appendix D
33. Blu ray player s blue receptacle which is typically labeled Pb or B Connect the RGB green video plug to your DVD or Blu ray player s green receptacle which is typically labeled Y or G ACIN gp VIDEO 31 UJE 669 A 1 f we 25 Y mi Connect the red audio plug to your DVD or Blu ray player s remaining red receptacle which is typically labeled R Connect the white audio plug to your DVD or Blu ray player s white receptacle which is typically labeled L NOTE You previously connected the other end of this cable to your flat panel display see page 20 2 Connect your DVD or Blu ray player s power cable not included with your SMART Mobile Stand to an available receptacle on your SMART Mobile Stand s power bar TIP Coil and bundle the cable with the included hook and loop fastener strap A NOTE Don t connect your SMART Mobile Stand to a power outlet before you install the rear access panels page 58 1010651 Rev C1 27 MODEL FSSBID 100 CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET To connect 1 Connect the three plug RCA cable AVO2 as follows your VCR Connect the yellow plug to your VCR s yellow receptacle which is typically labeled V or VIDEO Connect the red audio plug to your VCR s appropriate red receptacle which is typica
34. IP Coil and bundle the cable with the included hook and loop fastener strap B NOTE Don t connect your SMART Mobile Stand to a power outlet before you install the rear access panels page 58 Cable Connections to Your SMART Hub PE260 39 NS O A N e EN Q 9 AN o 9 OX NS Da O QS QU gt SOS amp SES SO KE VEES ees A9 dy S ST lt C 2 O O l 3 5mm VGA RJ45 Stereo V Cable Cable Audio AVO1 N01 Cable AVO1 DC In 12V 30V BENE USB USB USB Cable Cable Cable C01 C02 C03 LI LI oe e RETS A F p od qe 0 Q a 2 A 99 SX Sq SS n h e d Y ne q 1010651 Rev C1 25 MODEL FSSBID 100 CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET Connecting a DVD Blu ray Player or VCR Your SMART Mobile Stand supports audiovisual devices including a DVD Blu ray player or VCR Internal connections provide support for a component video device with stereo audio and a composite video device with stereo audio D CAUTION If you install additional audio or video cables other than those provided with your SMART Mobile Stand SMART Board interactive display frame SMART Board for
35. Installation and Integrator s Guide SMART Mobile Stand for Interactive Displays Models FSSBID 100 and FSSBID 100H Extraordinary made simple SMART Product Registration If you register your SMART product we ll notify you of new features and software upgrades Register online at www smarttech com registration Keep the following information available in case you need to contact SMART Technical Support Serial Number Date of Purchase Trademark Notice SMART Board smarttech Senteo and the SMART logo are trademarks or registered trademarks of SMART Technologies ULC in the U S and or other countries Phillips is a registered trademark of Phillips Screw Company TORX is a registered trademark of Acument Intellectual Properties LLC in the United States or other countries All other third party product and company names may be trademarks of their respective owners Copyright Notice 2009 2014 SMART Technologies ULC All rights reserved No part of this publication may be reproduced transmitted transcribed stored in a retrieval system or translated into any language in any form by any means without the prior written consent of SMART Technologies ULC Information in this manual is subject to change without notice and does not represent a commitment on the part of SMART This product and or use thereof covered by one or more of the following U S patents www smarttech com patents 01 2014 Important I
36. Leave enough slack in this cable to create a strain relief loop Use a plastic cable tie to fasten this cable to the clip on the inside of your SMART Mobile Stand s speaker panel as illustrated on page 31 1010651 Rev C1 30 MODEL FSSBID 100 CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET 7 Route your interactive display frame s camera cables through the connection panel from the right side up your SMART Mobile Stand s prewired cable harness down behind the speaker panel and along the inside edge of the pencil ledge as shown page 31 TIPS To route the camera cables remove the plastic cable ties securing the cable harness to your SMART Mobile Stand s top horizontal mounting bar remove the nylon sleeve and then loosen all the hook and loop fastener straps Remove each plastic cable tie by pressing down on the plastic tab while you pull the tie backward After you route the camera cables secure them together with the rest of the cables with the hook and loop fastener straps and nylon sleeve and then secure the cable bundle to the top horizontal mounting bar with the plastic cables ties 8 Connect the camera cables to your frame s bottom corner blocks 1010651 Rev C1 31 MODEL FSSBID 100 CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET 9 Route the other end of the camera cables back through the connection panel f
37. MART Board interactive display frame s controller box to your SMART Mobile Stand instead of directly to a computer Refer to the SMART Board interactive display frame Installation and User s Guide smarttech com kb 125254 for general instructions on installing your SMART Board interactive display frame on your flat panel display 1 Rotate your SMART Mobile Stand s height adjustment handle to raise your flat panel display frame to its highest position 2 Working inside your SMART Mobile Stand s cabinet from the back secure your SMART Board interactive display frame s controller box to the mounting holes on the left side of the connection panel with the four screws included in your stand s accessory kit IMPORTANT Ensure that the controller box s LEDs face downward 51 MODEL FSSBID 100H CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET 3 Connect your SMART Board interactive display frame s power cable to your interactive display frame s power supply 4 Connect the cable from your SMART Board interactive display frame s power supply to the controller box g TIP Route this cable up the cabinet s rear support tube and behind the hydraulic pump leaving enough slack to create a strain relief loop 5 Connect the other end to an available receptacle on your SMART Mobile Stand s power bar and then coil and bundle any excess cable g TIP Place the power supply s transformer box next to th
38. RT Mobile Stand for a rack mount you can purchase a hardware accessory kit from your authorized SMART reseller This kit includes 16 rack clips so that you can mount up to four peripheral racks Standard Replaceable Parts If your SMART Mobile Stand requires replacement parts make sure that the service technician uses replacement parts specified by SMART Technologies To order replacement parts contact your authorized SMART reseller 9 ASSEMBLING YOUR SMART MOBILE STAND Assembling Your SMART Mobile Stand Your SMART Mobile Stand requires minimal assembly Consult the SMART Mobile Stand for Interactive Displays Textless Installation Instructions smarttech com kb 132293 included with your unit for instructions on installing your SMART Mobile Stand F3 WARNING Failure to follow the installation instructions included with your SMART Mobile Stand for Interactive Displays could result in personal injury or product damage D CAUTION Make sure that the weight of your flat panel display is minimum 90 Ib 40 8 kg and maximum 265 Ib 120 2 kg For a list of flat panel displays supported by your SMART Mobile Stand see smarttech com supportedpanels This chapter includes additional information and tips to consider when you install your SMART Mobile Stand Topics include Environmental Requirements page 10 e Things to Consider When Assembling Your SMART Mobile Stand page 11 Installing Your Flat Panel Display on Your SMART
39. Stand 1010651 Rev C1 14 ASSEMBLING YOUR SMART MOBILE STAND Adjusting the Shelves Your SMART Mobile Stand includes two vertically adjustable shelves The spacing of these shelves ranges from 2 to 19 5 1 cm to 48 3 cm Consider whether you plan to install a SMART Hub DVD Blu ray player or VCR in your unit when determining the best height for these shelves Typically you will install your DVD Blu ray player on the top shelf and then install your VCR on the bottom shelf g TP If you ordered model FSSBID 100H install your SMART Hub SE240 see page 38 in your SMART Mobile Stand before you install the shelves To determine your model of stand see page 7 1 Ifthe shelves are already installed in your SMART Mobile Stand remove them from the cabinet and then remove the eight shelf clips A NOTE If you need instructions for removing your rear access panels see steps 1 to 3 in Appendix A Configuring a Rack Mount on page 69 or the SMART Mobile Stand for Interactive Displays Textless Installation Instructions smarttech com kb 132293 2 Install four of the included shelf clips at the desired height for the first shelf IMPORTANT These clips secure to the cabinet s left and right front rack rails rear support tubing and side wall as shown in the following illustration Ensure that you leave at least 1 2 5 cm of space above equipment for cooling 15 ASSEMBLING YOUR SMART MOBILE STAND 3 Slide the shelf o
40. TING OTHER PRODUCTS TO YOUR SMART MOBILE STAND Your SMART Mobile Stand s Connection Panel Network Standard USB A Connection FSSBID 100H only WARNING Your SMART Mobile Stand is designed to operate with a maximum power consumption of 1200 W Exceeding this consumption could result in fire personal injury or death 1010651 Rev C1 USB A Connection for SMART Document Camera SMART Response formerly Senteo Receiver Wireless Mouse Wireless Keyboard USB Storage Device NOTE These USB receptacles don t work when you connect a guest laptop computer to your SMART Mobile Stand Guest Laptop Computer Ensure that any cables extending across the floor to your SMART Mobile Stand are properly bundled and marked to prevent a tripping hazard Do not move your SMART Mobile Stand while external cables are connected or when the power is on 61 COMPLETING YOUR INSTALLATION AND CONNECTING OTHER PRODUCTS TO YOUR SMART MOBILE STAND Connecting a Guest Laptop Computer You can connect a guest laptop
41. USB A male plug of the USB A to USB B cable not included that you previously connected to your SMART Hub SE240 to an available USB receptacle on your computer see page 45 Connect your computer s power cable not included with your SMART Mobile Stand to an available receptacle on your stand s power bar TIP Coil and bundle the cable with the included hook and loop fastener strap 1010651 Rev C1 48 MODEL FSSBID 100H CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET Connecting a DVD Blu ray Player or VCR Your SMART Mobile Stand supports audiovisual devices including a DVD Blu ray player or VCR Internal connections provide support for an S video device with stereo audio and a composite video device with stereo audio CAUTION If you install additional audio or video cables other than those provided with your SMART Mobile Stand SMART Board interactive display frame SMART Board for Flat Panel Displays interactive overlay or as part of an adapter kit SMART assumes no responsibility and you are solely responsible for any damage incurred to your SMART Mobile Stand its cabling or other devices IMPORTANT The following procedures are generic instructions and your DVD or Blu ray player or VCR s connection panel might not resemble the illustrations or color codes referenced in this guide Refer to the documentation included with your device for specific connection instructions Forsome DVD and Blu ray
42. V1 LON sulel OV asn mo Od v09 09 v asn Jejdepy Oq OV k Nima coo v asn L09 S09 ASN PSIH asn o 19 sS Rods LOV pOAV J UNI POV A INO oipny T oL EON YOAV yOAV vov TNO olpny jaueg uon5 uuoo INO o p A ul od EEE Sule N OV ul asn 105 TON OMISN asn 200 21989 ISA JewojsnD ROH srl ul gsn 05 SOAV NO 0819 S gsn z Jajnduog 709 SOAV MO VOA Z olpny JajnduoD Jejnduog J3UOISNO LOV u OAPIA Z 1ajnduo9 no EON SUE OV Sule OV asn Jeinduo aiqed ASN Jewojsn 0 gs 9 ino lsoduoo AVL C OV olpny JejnduoD 20AV SOAV MO orpny A U O9pIA 19jnduio2 e 900v EON INO oipny 1 olpny 4 ZOAV i ZOAV HOA Bra om 29142 1euiojsn olpny 1 TONV oaPIA lisoduuo suje PIA 5 N OV oipny s cov ZOA Mo OBPIA S oipny 1 cov Gov NO olpny A OBPIA S Sov MO eiPnv 1 CON 0F7Z3S qnH LUVNS Jakeld GAG B a 940 eoweq JEUOISNI Jeg Jewogd 1010651 Rev C1 79 SMART MOBILE STAND RUNNING DIAGRAMS Cable Descriptions Used on This Model e NA North American Model INT International Model IO Required for Interactive Overlays pozi SMART NA INT NA INT Cable From To Description Length Part No 100 100 100H 100H Audio Video AV01 Computer Flat Panel VGA Male 3 5 mm Male 10 8 m 93 00683 20 e e Display to VGA Male 3 5 mm Male AV02 D
43. amera functionality Refer to the SMART Document Camera 280 Installation and User s Guide smarttech com kb 122667 to learn how to use your document camera s more advanced features 1 Connect the USB cable included with your SMART Document Camera from your document camera to either of the adjacent vertical USB A connections marked USB or the USB receptacle marked with an image of a tower computer FSSBID 100H only on your SMART Mobile Stand s connection panel see page 60 or to an available USB receptacle on your computer IMPORTANT If you are using a guest laptop computer with your SMART Mobile Stand you will not be able to use either of the adjacent vertical slots marked USB on the connection panel 2 Connect your SMART Document Camera s power adapter to the extension cable at the rear bottom of your SMART Mobile Stand A NOTE Place your SMART Document Camera on a nearby table desk shelf or cart so that you have sufficient room to work 1010651 Rev C1 1010651 Rev C1 To connect your receiver 64 COMPLETING YOUR INSTALLATION AND CONNECTING OTHER PRODUCTS TO YOUR SMART MOBILE STAND Connecting Your SMART Response formerly Senteo Interactive Response System Receiver Your SMART Mobile Stand integrates with your SMART Response interactive response system through a USB A connection Although receivers don t require an unobstructed line of sight transmission path such as infrared devices require you can operate
44. apter AD09 USB A Female to Cable N01 Cable V01 USB B Female RJ45 Male Connector 5 x BNC RGB HV Part No ADP USB AB To Your Computer To Your Flat Panel Display Sold Separately 1010651 Rev C1 1010651 Rev C1 84 SMART MOBILE STAND RUNNING DIAGRAMS FSSBID 100H Cable Graphics Cable 401 Cables A02 and A03 Sie ue PaL MR 3 5 mm Stereo Audio Plug Speaker Wires To Your SMART Hub SE240 To Your Flat Panel Display To Your Flat Panel Display ika RIS m so Eu 3 5 mm Stereo Audio Plug Cable A04 2 x RCA Plugs To Your Flat Panel Display To Your SMART Hub SE240 cr mm wd M a ja i Rar ga 2 x RCA Plugs Cable A05 2 x RCA Plugs To Your SMART Hub SE240 To Device One e g DVD Blu ray Player ELE Ham ma qu i g GRO gt 1 Za MSS me Do 3 x RCA Plugs Cable AV02 3 x RCA Plugs To Your Flat Panel Display To Device Two e g VCR um E H 2 w 3 5 mm Stereo Audio Plug Cable AVO5 3 5 mm Stereo Audio Plug Adapter AD08 DVI Male to VGA Female VGA Video Male Connector VGA Video Male Connector Included with Your To AD08 and Your SMART Hub SE240 To Your Computer SMART Hub SE240
45. ar Access Panels on Your SMART Mobile Stand page 58 The Connection Panel page 59 Connecting a Guest Laptop Computer page 61 Connecting Your SMART Document Camera page 63 Connecting Your SMART Response formerly Senteo Interactive Response System Receiver page 64 Connecting Other USB Devices page 66 1010651 Rev C1 58 COMPLETING YOUR INSTALLATION AND CONNECTING OTHER PRODUCTS TO YOUR SMART MOBILE STAND Installing the Rear Access Panels on Your SMART Mobile Stand After you connect your computer or SMART Hub and perhaps your DVD Blu ray player or VCR to your SMART Mobile Stand reinstall the rear access panels on your unit To install the rear Replace the upper rear panel that you removed from your SMART Mobile Stand access panels secure the bottom two screws with the included security TORX key and then secure the top two screws with a Phillips No 2 screwdriver 2 Replace the lower rear panel that you removed and then secure all four screws with the included security TORX key D CAUTION Take care to properly route the power cables through the two cutouts in the bottom of the lower rear panel so that you do not damage the cables 3 Connect your SMART Mobile Stand s power cable to a power outlet 1010651 Rev C1 59 COMPLETING YOUR INSTALLATION AND CONNECTING OTHER PRODUCTS TO YOUR SMART MOBILE STAND
46. camera cables to your frame s bottom corner blocks 1010651 Rev C1 53 MODEL FSSBID 100H CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET 9 Route the other end of the camera cables back through the connection panel from right to left and then connect them to your SMART Board interactive display frame s controller box coiling the excess cable and fastening it to the speaker panel with cable ties as shown on page 53 g TIP Leave some slack throughout the length of these cables Don t pull them tight Cable Connections to Your SMART Board interactive display frame Route camera cables up your SMART Mobile Stand s prewired cable harness down behind the speaker panel and along the inside AA M psec edge of the pencil ledge Camera Camera Speaker Panel Coil and fasten the excess camera cables to the clips on the speaker panel with plastic cable ties Power Cable to Your Controller Box with Strain Relief Loop Connect the USB cable included with your interactive display frame to the controller box coil the excess cable and then fasten it to the clip on the speaker panel with a plastic cable tie 1010651 Rev C1 54 MODEL FSSBID 100H CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET IMPORTANT Ensure that your SMART Board interactive display frame is functioning correctly before you install the rear access panels on your SMART Mobi
47. computer to your SMART Mobile Stand by means of your stand s connection panel Consult the Laptop Shelf for SMART Mobile Stands for Interactive Displays Textless Installation Instructions smarttech com kb 133368 included with your laptop shelf for instructions on installing it on your SMART Mobile Stand IMPORTANT You will not be able to use either of the adjacent vertical USB A connections marked USB or the USB receptacle marked with an image of a tower computer FSSBID 100H only on your SMART Mobile Stand s connection panel see page 60 when you connect a guest laptop computer to your stand The following procedure refers to these cables VGA Video Male Cable 3 5 mm Stereo Audio Plug Both Ends Both Ends Joined and Marked AV04 Not Part of Prewired Cable Harness USB A Male Plug of Cable C05 1010651 Rev C1 To connect a guest laptop computer 1010651 Rev C1 62 1 COMPLETING YOUR INSTALLATION AND CONNECTING OTHER PRODUCTS TO YOUR SMART MOBILE STAND Connect one of the VGA video plugs from cable AV04 to your laptop computer s video receptacle Connect the 3 5 mm stereo audio plug from the same end of cable AV04 to your laptop computer s audio receptacle Connect the other VGA video plug from cable AV04 to the receptacle marked VGA In on your SMART Mobile Stand s connection panel Connect the other 3 5 mm stereo audi
48. d Climbing or riding on your SMART Mobile Stand could result in personal injury or product damage For European customers only Your SMART Mobile Stand should be used only with European TN and TT power distribution systems It is not suitable for older IT type power distribution systems found in some European countries This system IT type is widely used isolated from earth in some installations in France with impedance to earth at 230 400V and in Norway with voltage limiter neutral not distributed at 230V line to line IEC 60950 1999 Contact qualified personnel if you are uncertain about the type of power system available where you are installing your SMART Mobile Stand To reduce the risk of fire or electric shock do not expose your SMART Mobile Stand to rain or moisture Your SMART Mobile Stand is designed to operate with a maximum power consumption of 1200 W Exceeding this consumption could result in fire personal injury or death IMPORTANT INFORMATION CAUTION Make sure that the weight of your flat panel display is minimum 90 Ib 40 8 kg and maximum 265 Ib 120 2 kg For a list of flat panel displays supported by your SMART Mobile Stand see smarttech com supportedpanels To prevent damage to a 60 152 4 cm or larger flat panel display when it is installed with a SMART Board for Flat Panel Displays interactive overlay make sure that you install the included clevis pin as instructed in this guide
49. d maintenance instructions To ensure operating safety and to prevent product damage observe the following precautions Do not set up or use your SMART Mobile Stand in an area with excessive levels of dust dirt humidity or smoke Disconnect your SMART Mobile Stand s power plug from the power outlet before cleaning the unit or if you won t be using it for a long period of time Use a soft cloth moistened with a mild detergent to clean the unit s housing If your SMART Mobile Stand requires replacement parts make sure that the service technician uses replacement parts specified by SMART Technologies Contents Important Information U UU u uu u u u u nnns anne nnn innen i Safety Warnings and Cautions n i Other Preca tiOnS M aada iv About Your SMART Mobile Stand nana nennen nennen nnns 1 SMART Mobile Stand Features sss 2 Power Specifications nana 7 Hardware and Internet Connection Requirements 7 Determining Your Model of SMART Mobile Stand tine ette reiten detecto diet esent 7 Optional ACCOeSSOLrIOS u u eet ese a date re Da et ate Rea vale 8 Standard Replaceable Parts nan 8 Assembling Your SMART Mobile Stand 9 Environmental Requirements a 10 Th
50. e cover of this manual if you printed it The serial number for your SMART Mobile Stand is located on the back right hand side of your unit s speaker panel near the top The serial number has a five digit numeric format for example FSSBID1 R2 00000 for FSSBID 100 models or FSSBID1H R2 00000 for FSSBID 100H models Appendix A Configuring a Rack Mount Although your SMART Mobile Stand comes configured for shelving it can also accommodate an optional 19 48 cm rack mount configuration A NOTE If you want to configure your SMART Mobile Stand for a rack mount you can purchase a hardware accessory kit which includes 16 rack clips from your authorized SMART reseller lt x SMART Mobile Stand from the Front with Doors Open Showing Rack Mount Configuration 1010651 Rev C1 70 CONFIGURING A RACK MOUNT To remove the shelving 1 Remove the four screws in the lower rear panel of your SMART Mobile Stand and rear support tube with the included security TORX key and then remove the panel Keep these screws nearby 2 Remove the top two screws in the upper rear panel with a Phillips No 2 screwdriver Keep these screws nearby 3 Remove the bottom two screws in the upper rear panel with the included security TORX key and then remove the panel Keep these screws nearby
51. e power bar on the floor of your SMART Mobile Stand s cabinet 6 Connect the USB cable included with your SMART Board interactive display frame to the USB receptacle on your interactive display frame s controller box A NOTE You previously connected the other end of this cable to your SMART Hub SE240 see page 45 USB B Plug g TIP Coil the excess cable and then fasten it to a clip on the inside of your SMART Mobile Stand s speaker panel as illustrated on page 53 1010651 Rev C1 52 MODEL FSSBID 100H CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET 7 Route your interactive display frame s camera cables through the connection panel from the right side up your SMART Mobile Stand s prewired cable harness down behind the speaker panel and along the inside edge of the pencil ledge as shown on page 53 TIPS To route the camera cables remove the plastic cable ties securing the cable harness to your SMART Mobile Stand s top horizontal mounting bar remove the nylon sleeve and then loosen all the hook and loop fastener straps Remove each plastic cable tie by pressing down on the plastic tab while you pull the tie backward After you route the camera cables secure them together with the rest of the cables with the hook and loop fastener straps and nylon sleeve and then secure the cable bundle to the top horizontal mounting bar with the plastic cable ties 8 Connect the
52. en tray or pencil ledge while adjusting the height of your SMART Mobile Stand 1010651 Rev C1 1010651 Rev C1 IMPORTANT INFORMATION Use the SMART Mobile Stand s three grab bars to move the unit Do not press pull or push on the flat panel display interactive overlay or display frame cabinet doors rear access panel plastics or vertical brackets Before moving your SMART Mobile Stand make sure that you unlock the casters These casters are designed to roll on common indoor surfaces While you move the unit your view may be partially obstructed Be aware of surrounding obstacles Do not move your SMART Mobile Stand while external cables are connected or when the power is on You must connect the USB cable that came with your SMART Mobile Stand to a computer that has a USB 2 0 compliant interface and that bears the USB logo In addition the USB source computer must be compliant with CSA UL EN 60950 and bear the CE mark and CSA and or UL Mark s for CAS UL 60950 This is for operating safety Ensure that any cables extending across the floor to your SMART Mobile Stand are properly bundled and marked to prevent a tripping hazard Do not stand or allow children to stand on a chair to touch the surface of your flat panel display Instead rotate your SMART Mobile Stand s height adjustment handle to lower your display to the appropriate height Do not climb or ride or allow children to climb or ride on your SMART Mobile Stan
53. eo Male Blu ray Player V03 SMARTHub Connection DVI Male 6 1 8m 93 00608 20 SE240 Panel to VGA Female Chassis V04 SMARTHub Flat Panel DVI Male to VGA Male 6 1 8m 93 00530 00 SE240 Display Control C01 Computer Connection USB A Male 6 1 8m 93 00677 20 e e e e SMART Hub Panel to USB A Female Chassis SE240 C02 Computer Connection USB A Male 6 1 8 m 93 00687 20 e e e e SMART Hub Panel to USB A Female Chassis SE240 C03 Computer Connection USB A Male 6 1 8 m 93 00688 20 e e e e SMART Hub Panel to USB A Female Chassis SE240 C04 Connection AD09 USB B Female Chassis 20 93 00679 20 e e e e Panel Interactive to USB B Male 51 cm Touch Display Frame Controller SMART Hub SE240 C05 Laptop Connection USB A Male to USB B Male 6 1 8m 93 00678 20 e e e e Panel Network NO1 Connection Computer Cat5e RJ45 Male 4 1 2m 93 00682 20 e e e e Panel SMART Hub to Cat5e RJ45 Male SE240 Adapters ADO1 Power Bar IEC Male N A Various e e to Country Specific Female ADO2 Power Bar IEC Male N A Various e e to Country Specific Female ADO3 Power Bar IEC Male N A Various e e to Country Specific Female AD04 AC Y IEC Male N A Various to Country Specific Female 1010651 Rev C1 81 SMART MOBILE STAND RUNNING DIAGRAMS Au SMART NA INT NA INT Cable From To Description Length Part No 100 100
54. er panel follow the path of the installed cable harness 13 ASSEMBLING YOUR SMART MOBILE STAND Securing the Clevis Pins When Installing a 60 152 cm or Larger Flat Panel Display Follow these instructions if you intend to install a SMART Board for Flat Panel Displays interactive overlay with a 60 152 4 cm or larger flat panel display D CAUTION To prevent damage to a 60 152 4 cm or larger flat panel display when it is installed with a SMART Board for Flat Panel Displays interactive overlay make sure that you install the included clevis pin as instructed in this guide To secure the two 1 Rotate your SMART Mobile Stand s height adjustment handle to raise your included clevis pins flat panel display to its highest position 2 Insert each of the two included clevis pins as shown in the following illustration making sure that the clevis pin ring faces outward 1010651 Rev C1 To adjust the shelving in your SMART Mobile
55. er receptacles 2 Connect the VGA video plug from cable V04 to your flat panel display s VGA video receptacle 3 Connect the 3 5 mm stereo audio plug from cable A04 to an audio receptacle on your flat panel display s connection panel 4 Connect the SMART Mobile Stand s prewired power cable to your flat panel display s power receptacle 5 Connect the other end of this cable to an available receptacle on your SMART Mobile Stand s power bar IMPORTANT Your flat panel display won t look exactly like the one shown on page 41 Some flat panel displays require audio video adapters which you can purchase from your authorized SMART reseller Don t connect your SMART Mobile Stand to a power outlet before you install the rear access panels page 58 MODEL FSSBID 100H CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET 43 Connecting Your SMART Hub SE240 USB Cables RCA l x Cable A04 C01 2 RCA 1 x TY vo2 3 3 5 mm Stereo C02 C03 aj l i ss RJ45 Cable zala GE 34 e Audio Cable
56. essssssoo Cabinet Venting 1010651 Rev C1 Serial Number Location Connection Panel 1 Large Removable OA SMART Mobile Stand from the Rear Access Panels 5 ABOUT YOUR SMART MOBILE STAND 000090009 oood posooooooogo 99009999050 000000000 Prominent Grab Bars for Moving Your Unit Supports Integration with a SMART Hub SE240 Model FSSBID 100H Only Dedicated Space Adjustable Shelving for a Computer Power Management Swiveling Lockable Non Marking Casters SMART Mobile Stand from the Rear Lower Panel Removed 1010651 Rev C1 6 ABOUT YOUR SMART MOBILE STAND 3505000000 000000 an nn 99099990 nn 0000060060000005000000000900000 uu oo to U oo 9995089 SMART Mobile Stand from the Front with Doors Open Showing Rack Mount Configuration 1010651 Rev C1 7 ABOUT YOUR SMART MOBILE STAND Power Specificat
57. evice Two Flat Panel Three Plug RCA Male 8 2 4 m 93 00685 20 e e e e e g VCR Display to Three Plug RCA Male SMART Hub SE240 AV03 Device One Flat Panel Five Plug RCA Male 8 2 4 m 93 00684 20 e e e g DVD Display to Five Plug RCA Male Blu ray Player AV04 Laptop Connection VGA Male 3 5 mm Male 6 1 8 m 93 00699 20 e e e e Panel to VGA Male 3 5 mm Male AV05 Computer SMART Hub VGA Male 3 5 mm Male 6 1 8 m 93 00699 20 e e SE240 ADO8 to VGA Male 3 5 mm Male Audio A01 Connection Flat Panel 3 5 mm Stereo Female 6 1 8m 93 00681 20 e e e e Panel Display Chassis to 3 5 mm Male SMART Hub SE240 A02 Flat Panel Speaker 16 AWG Speaker Cable 8 1 2 93 00686 20 e e e e Display 2 6 m A03 Flat Panel Speaker 16 AWG Speaker Cable 8 1 2 93 00689 20 e e e e Display 2 6 m A04 SMART Hub Flat Panel Two Plug RCA Male 6 1 8 m 93 00513 20 e e SE240 Display to 3 5 mm Male A05 Device One SMART Hub Two Plug RCA Male 6 1 8 m 93 00139 20 e e e g DVD SE240 to Two Plug RCA Male Blu ray Player 1010651 Rev C1 80 SMART MOBILE STAND RUNNING DIAGRAMS no SMART NA INT NA INT Cable From To Description Length Part No 400 100 100H 100H Video V01 Connection Flat Panel VGA Female Chassis 6 1 8 m 93 00680 00 e e Panel Display to Five Plug BNC RGBHV Male vo2 Device One SMART Hub S Video Male 6 1 8 m 93 00202 20 e e e g DVD SE240 to S Vid
58. i dcr nen cera de ra bere aden Na uas 87 Online Information and Support 87 ST PEMA u a ubt s dote e ees ede dae 87 Technical Support iei eei ete Dente EN K Enea 87 lE cu 87 Registratlom zu ess dere RE to e ose rie aad tuus 87 II uu 2 89 1010651 Rev C1 viii CONTENTS 1010651 C1 1 ABOUT YOUR SMART MOBILE STAND About Your SMART Mobile Stand Your SMART Mobile Stand is an easy to use fully integrated height adjustable stand that adds mobility to select SMART Board interactive displays For a list of flat panel displays supported by your SMART Mobile Stand see smarttech com supportedpanels Your SMART Mobile Stand s prewired cable harness includes the necessary cables for you to easily connect your flat panel display to your audio speakers computer or SMART Hub and additional devices including a DVD Blu ray player or VCR This chapter describes the features of your SMART Mobile Stand and accessories that you can use with your unit e SMART Mobile Stand Features page 2 Feature Highlights page 2 Power Specifications page 7 Hardware and Internet Connection Requirements page 7 Computer Hardware page 7 Local Area Network LAN Connection Optional page 7 e Determining Your Model of SMART Mobile Stand page 7 e Optional Accessories page 8 Optional Laptop Shelf page 8 Flat Panel Display Adapter Kit page 8 SMART Board fo
59. iagrams Appendix B pieoq liuA aanoesajul SAejdsig Joueg j6 3 10 pieog LYVIS Ile sui NOA ji AC Buum ejeoipui seui peuojeH 310N Hi Jejdepy OG OV ul 90 AZL uy enag kel uod Keano 9 noeloju Jejdepy ieuas o gsn Jejdepy Oq OV U OO Aci ul gsn dojde 1A uuolsnO oL 059 J llonuoS aLuei Aejdsig eAnoereju sujen OV Joyeeds ubr ez a mno oipnv seyeeds e 9 1o oienv si ye ds TON palimaid noi TON HI Sam Fon O TEB TO afana Ton I pee TON 08191S uuu G g VIA oipny Y opny 1 HOA Bra om 29142 JAUOJSNA O6pIA ajisoduoo TON GPK opny s olpny s oipny 1 oipny 1 9 Juauodwog yusuodwi0g g juauoduiod ig 1usuoduioo Y 1ueuoduio SAV TOAV ly jueuoduio Kejdsig jeued je J 19U10 SND Jefe d AAG 6 a uo anaq Jawo snD Jeg Jamod 1010651 Rev C1 SMART MOBILE STAND RUNNING DIAGRAMS FSSBID 100H North America 76 pieoq liuA eAnoeJoajul SAB dSIG Jaueg ej4 10 pseog L IVINS IIe sui nof Ji GULIIM SJE9JIPU seui POUJJEH 310N suen oyle NVWNV1 LON ino oq suten OV gasn Jejdepy Oq Ov ino oq 709 S00 v gsn Ja depy Oq OV 09 ama u 90 209 uy jeues asn 105 v ISA S00 dojde3 i09J9 1S Jawojsna kel ueg ejieAQ 249819JU MNO oipny vov VOAV f VOAV i son 9 S 0AV TYOAV pov gt 1 nO oipny I8ueq uonoeuuo2 MO ZezSA w8Sh Sgs gs MO o p A
60. ing power For more information about using your SMART Response formerly Senteo interactive response system refer to the SMART Response User s Guide smarttech com kb 134078 1010651 Rev C1 1010651 Rev C1 66 COMPLETING YOUR INSTALLATION AND CONNECTING OTHER PRODUCTS TO YOUR SMART MOBILE STAND Connecting Other USB Devices Your SMART Mobile Stand integrates with USB devices including a keyboard mouse or USB storage device SMART recommends that you purchase a wireless keyboard and mouse to use with your SMART Mobile Stand These wireless devices enable greater freedom of movement while you work with your unit and interactive display Connect them directly to the USB A receptacles on your SMART Mobile Stand s connection panel or to an available USB receptacle on your computer IMPORTANT Because of USB communication limitations ensure that the cable connecting your USB device to your SMART Mobile Stand is not longer than 10 3 m Connecting a Wired Keyboard or Mouse If you decide to use a wired keyboard or mouse connect these devices to either of the USB A receptacles marked USB or the USB receptacle marked with an image of a tower computer FSSBID 100H only on your SMART Mobile Stand s connection panel illustrated on page 60 or to an available USB receptacle on your computer F3 CAUTION If your wired keyboard mouse or other USB device is damaged while it is attached to your SMART Mobile Stand SMART assume
61. ings to Consider When Assembling Your SMART Mobile Stand 11 Installing Your Flat Panel Display on Your SMART Mobile Stand 12 Adjustng the Shelv8s uu teet ttti bc ettet e eu i Po 14 Model FSSBID 100 Connecting Devices Inside Your SMART Mobile Stand s Cabinet eese 17 Connecting Your Flat Panel Display 18 Connecting Your Computer 21 Connecting Your SMART Hub PE2960 nn 23 Connecting a DVD Blu ray Player or VCR 25 Connecting Your SMART Board interactive display frame 28 Connecting Your SMART Board for Flat Panel Displays Interactive Overlay 32 1010651 Rev C1 vi CONTENTS Model FSSBID 100H Connecting Devices Inside Your SMART Mobile Stand s Cabinet nana nana nennen nnn nena 37 Installing Your SMART Hub SE240 sss 38 Connecting Your Flat Panel Display 41 Connecting Your SMART Hub SE240 sse 43 Connecting Your Computer 46 Connecting a DVD Blu ray Player or VCR 1 48 Connecting Your SMART Board interactive display frame 50 Connecting Your SMART Board for Flat Panel Displays Interactive Overlay 55 Completing Your Installation and Connecting Other Products
62. ions Your SMART Mobile Stand s user friendly power management design accommodates up to 1 2 kW and includes the following features Acountry specific power bar North America NEMA 110V AC or IEC 240V 50 Hz which provides power access for additional devices near the bottom rear of your stand An8 2 44 m country specific power cord international only Acountry specific extension cable e Country specific power adapters A USB 2 0 cable Hardware and Internet Connection Requirements Computer Hardware You need at least three USB receptacles recommended on your computer to connect it to your SMART Mobile Stand If your computer has fewer than three available USB receptacles you need a USB hub not included to connect your computer to your stand Local Area Network LAN Connection Optional Your SMART Mobile Stand includes a standard RJ45 LAN connection point to connect your computer to your network You need an external source so that you can access the Internet Determining Your Model of SMART Mobile Stand Your SMART Mobile Stand is either a standard model FSSBID 100 or one that includes support for a SMART Hub SE240 FSSBID 100H You can determine your model of SMART Mobile Stand by referring to its serial number which is located on the back right hand side of your unit s speaker panel near the top Ifyou have model FSSBID 100 the serial number follows the format FSSBID1 R2 XXXXX where X
63. is any number Ifyou have model FSSBID 100H the serial number follows the format FSSBID1H R2 XXXXX where X is any number 1010651 Rev C1 1010651 Rev C1 8 ABOUT YOUR SMART MOBILE STAND Optional Accessories Contact your authorized SMART reseller to order any of the following accessory parts Optional Laptop Shelf You can order a dedicated laptop shelf if you want to connect a laptop computer to your SMART Mobile Stand 3 This shelf is designed to mount on either side of your stand and features an adjustable tilt angle of up to 35 degrees from horizontal It telescopes outward to accommodate flat panel displays ranging from 50 127 cm to 65 165 1 cm in size For more information on ordering a laptop shelf for your SMART Mobile Stand contact your authorized SMART reseller Flat Panel Display Adapter Kits Some models of flat panel displays require audio video adapters which you can purchase from your authorized SMART reseller Your reseller can identify the type of adapter required for your flat panel display SMART Board for Flat Panel Displays Interactive Overlay Adapter Kit FSSBID 100 Only E IMPORTANT If you intend to use a SMART Board for Flat Panel Displays interactive overlay with your SMART Mobile Stand model FSSBID 100 you must purchase a USB B to USB A adapter ADO9 Part No ADP USB AB from your authorized SMART reseller Rack Mount Hardware Accessory Kit If you want to configure your SMA
64. le included with your interactive overlay to the right side of its power supply 5 Route the power cable through the connection panel from right to left behind the hydraulic pump and down the cabinet s rear support tube and then connect the other end to an available receptacle on your SMART Mobile Stand s power bar g TIP Coil and bundle the excess cable with the included hook and loop fastener strap fg NOTES Don t connect your SMART Mobile Stand to a power outlet before you install the rear access panels page 58 If you move your SMART Mobile Stand with a SMART Board for Flat Panel Displays interactive overlay installed secure the pens in the pen tray so that they don t fall out 57 COMPLETING YOUR INSTALLATION AND CONNECTING OTHER PRODUCTS TO YOUR SMART MOBILE STAND Completing Your Installation and Connecting Other Products to Your SMART Mobile Stand Your SMART Mobile Stand integrates with a guest laptop computer SMART Document Camera SMART Response formerly Senteo interactive response system and other peripheral devices This chapter includes precautions to follow and methods to use when connecting a new device to your SMART Mobile Stand Z IMPORTANT When connecting other SMART products to your SMART Mobile Stand refer to the documentation included with these accessories and consult the SMART Support website for additional instructions Topics covered in this chapter include Installing the Re
65. le Stand see page 58 Connect your SMART Mobile Stand temporarily to a power outlet while you check your interactive display frame 1010651 Rev C1 55 MODEL FSSBID 100H CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET Connecting Your SMART Board for Flat Panel Displays Interactive Overlay This section describes how to connect your SMART Board for Flat Panel Displays interactive overlay to your SMART Mobile Stand instead of directly to a computer Refer to the SMART Board for Flat Panel Displays Installation Guide Corner Brackets smarttech com kb 000769 for general instructions on installing your interactive overlay on your flat panel display Cable Connections to Your Interactive Overlay Power Cable to Your SMART Board for Flat Panel Displays Interactive Overlay s Pen Tray Hook and Loop Fastener Strap Power Cable to Power Supply Loosen the hook and loop fastener strap below the connection panel coil the DB9 to USB adapter cable s excess length and then To connect your interactive overlay HOMES eR A a a secure it with the hook and loop lt fastener strap 1 vu pe
66. lly labeled R Connect the white audio plug to your VCR s appropriate white receptacle which is typically labeled L fj NOTE You previously connected the other end of this cable to your flat panel display see page 19 Cable AVO2 2 Connect your VCR s power cable not included to an available receptacle on your SMART Mobile Stand s power bar g TIP Coil and bundle the cable with the included hook and loop fastener strap A NOTE Don t connect your SMART Mobile Stand to a power outlet before you install the rear access panels page 58 1010651 Rev C1 To connect your interactive display frame 1010651 Rev C1 28 MODEL FSSBID 100 CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET Connecting Your SMART Board interactive display frame This section describes how to connect your SMART Board interactive display frame s controller box to your SMART Mobile Stand instead of directly to a computer Refer to the SMART Board interactive display frame Installation and User s Guide smarttech com kb 125254 for general instructions on installing your SMART Board interactive display frame on your flat panel display A NOTE You don t need the USB cable included with your SMART Board interactive display frame to complete the following procedure 1 Rotate your SMART Mobile Stand s height adjustment handle to raise your flat panel display to its highest positio
67. mount slots further to the left A NOTE The rack mount slots in the bottom of the cabinet will align the rail properly 4 Straighten the rack rail aligning the holes in the flange at the top of the rail to the pilot holes in the cabinet s top panel and then secure the rail with two of the screws that you removed in step 2 1010651 Rev C1 74 CONFIGURING A RACK MOUNT 5 Repeat steps 3 and 4 for the right rack rail except rotate the rail counter clockwise before inserting it into the rack mount slots 6 Secure each set of four rack mount clips included in your rack mount hardware accessory kit at the desired height for each rack A NOTE Install a SMART Hub SE240 in the second highest rack mount position To replace the rear 1 Replace the upper rear panel that you removed from your SMART Mobile Stand access panels secure the bottom two screws with the included security TORX key and then secure the top two screws with a Phillips No 2 screwdriver 2 Replace the lower rear panel that you removed and then secure all four screws with the included security TORX key D CAUTION Take care to properly route the power cables through the two cutouts in the bottom of the lower rear panel so that you do not damage the cables 1010651 Rev C1 ile Stand SMART Mob Running D
68. n 2 Working inside your SMART Mobile Stand s cabinet from the back secure your SMART Board interactive display frame s controller box to the mounting holes on the left side of the connection panel with the four screws included in your stand s accessory kit IMPORTANT Ensure that the controller box s LEDs face downward 29 MODEL FSSBID 100 CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET 3 Connect your SMART Board interactive display frame s power cable to your interactive display frame s power supply 4 Connect the cable from your SMART Board interactive display frame s power supply to the controller box g TIP Route this cable up the cabinet s rear support tube and behind the hydraulic pump leaving enough slack to create a strain relief loop 5 Connect the other end to an available receptacle on your SMART Mobile Stand s power bar and then coil and bundle any excess cable g TIP Place the power supply s transformer box next to the power bar on the floor of your SMART Mobile Stand s cabinet 6 Remove the plastic cable tie from the USB B male cable marked C04 in your prewired cable harness and then connect this cable to the USB receptacle on your interactive display frame s controller box A NOTE The other end of cable C04 is prewired to your SMART Mobile Stand s connection panel which connects to your computer or SMART Hub USB B Cable C04 g TIP
69. ncluded to an available receptacle on your SMART Mobile Stand s power bar g TIP Coil and bundle the cable with the included hook and loop fastener strap A NOTE Don t connect your SMART Mobile Stand to a power outlet before you install the rear access panels page 58 To connect 1 Connect the three plug RCA cable AVO2 as follows your VCR Connect the yellow plug to your VCR s yellow receptacle which is typically labeled V or VIDEO Connect the red audio plug to your VCR s appropriate red receptacle which is typically labeled R EN su BS ES HE um gt Loi Connect the white audio plug to your VCR s white receptacle which is typically labeled L A NOTE You previously connected the other end of this cable cilje to your SMART Hub SE240 see page 44 AVo2 2 Connect your VCR s power cable not included to an available receptacle on your SMART Mobile Stand s power bar g TIP Coil and bundle the cable with the included hook and loop fastener strap A NOTE Don t connect your SMART Mobile Stand to a power outlet before you install the rear access panels page 58 1010651 Rev C1 To connect your interactive display frame 1010651 Rev C1 50 MODEL FSSBID 100H CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET Connecting Your SMART Board interactive display frame This section describes how to connect your S
70. nformation Before you install and use your SMART Mobile Stand read and understand the safety warnings and precautions in this user s guide and the included warnings document These safety warnings and precautions describe the safe and correct operation of your SMART Mobile Stand and its accessories helping you prevent injuries and equipment damage safety Warnings and Cautions A WARNING Failure to follow the installation instructions included with your SMART Mobile Stand for interactive displays could result in personal injury or product damage Make sure that you properly engage and secure the vertical brackets both to your flat panel display and to your SMART Mobile Stand Read the safety warnings precautions and other important information contained in the documentation included with your other SMART products and published by your flat panel display s manufacturer Two people are reguired to safely assemble your SMART Mobile Stand and to mount or remove your flat panel display and your SMART Board interactive display frame or SMART Board for Flat Panel Displays interactive overlay Lock the casters before installing or working with your flat panel display on your SMART Mobile Stand or adjusting its height To prevent injury be aware of crush and pinch locations on the product marked with the crush symbol during assembly and use Do not rest your hand on the stand s universal mount or under the interactive product s p
71. ng Your Computer Your SMART Mobile Stand includes dedicated space for a tower computer behind the left cabinet door when your stand is configured for standard shelving Internal connections provide support for VGA video 3 5 mm stereo audio USB for interactive product touch control and two additional USB devices WARNING You must connect the USB cable that came with your SMART Mobile Stand to a computer that has a USB 2 0 compliant interface and that bears the USB logo In addition the USB source computer must be compliant with CSA UL EN 60950 and bear the CE mark and CSA and or UL Mark s for CAS UL 60950 This is for operating safety IMPORTANT SMART recommends that you have at least three USB receptacles on your computer to connect it to your SMART Mobile Stand If your computer has fewer than three available USB receptacles you need a USB hub not included to connect your computer to your stand Contact your authorized SMART reseller to order a recommended USB hub The following procedure refers to these cables which are prewired and included in your SMART Mobile Stand s cable harness i n VGA Video Male Cable 3 5 mm Stereo Audio Plug gg NOTES The VGA male cable and the 3 5 mm stereo audio cable are joined and marked AV01 in the prewired cable harness You previously connected the other end of these cables to your flat panel display page 19
72. ng your SMART Hub PE260 refer to the SMART Hub PE260 Configuration Guide smarttech com kb 127260 A NOTE If you want to connect a SMART Hub SE240 to your SMART Mobile Stand contact your authorized SMART reseller for more information 1 Follow the installation instructions included in the SMART Hub PE260 Textless Installation Instructions smarttech com kb 127261 g TIP You might find it easier to complete this connection procedure before securing your SMART Hub PE260 to your SMART Mobile Stand s cabinet 2 Connect the VGA video plug from cable AV01 in the prewired cable harness to your SMART Hub s VGA video receptacle marked Primary A NOTE You previously connected the other end of this cable to your flat panel display see page 19 3 Connect the 3 5 mm stereo audio plug from cable AV01 in the prewired cable harness to your SMART Hub s audio input receptacle marked with the audio waves symbol 2 4 Connect each of the three USB A male plugs from cables C01 C02 and C03 in the prewired cable harness to an available USB receptacle on your SMART Hub marked with the USB symbol lt gt 5 Connect RJ45 cable N01 to your SMART Hub s network LAN receptacle 1 6 Connect your SMART Hub s power cable included with your SMART Hub PE260 to an available receptacle on your SMART Mobile Stand s power bar 1010651 Rev C1 24 MODEL FSSBID 100 CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET g T
73. nternal power bar and a rear connection panel enable you to easily connect peripheral devices including a guest laptop computer SMART Hub SMART Document Camera SMART Response formerly Senteo interactive response system receiver DVD Blu ray player or VCR and other USB devices Front Facing Audio Your SMART Mobile Stand features high quality front facing integrated speakers High Quality Finish The polished high quality finish is dent resistant and easy to clean Easy Service Access Removable rear maintenance panels provide easy access to peripheral devices for cable installation and power management These panels are secured with tamper proof hardware 3 ABOUT YOUR SMART MOBILE STAND t ne i l L y ne I Hydraulic Height Optional Laptop Shelf T m Adjustment Handle e Mounts on Either Side of Your Stand e Adjustable Tilt Angle e Telescopes Outward High Quality Integrated Speakers Locking Cabinet for Secure Storage js t SMART Mobile Stand from the Front 1010651 Rev C1 4 ABOUT YOUR SMART MOBILE STAND o Sooooooooooq F
74. nto the shelf clips making sure to position the grooves on the bottom of the shelf so that it snaps in place 4 Repeat steps 2 and 3 for your second shelf 1010651 Rev C1 16 ASSEMBLING YOUR SMART MOBILE STAND 1010651 Rev C1 17 MODEL FSSBID 100 CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET Model FSSBID 100 Connecting Devices Inside Your SMART Mobile Stand s Cabinet This chapter explains how to connect your SMART Mobile Stand FSSBID 100 s prewired cable harness to your flat panel display computer or SMART Hub PE260 and other devices inside your stand s cabinet Your stand s cable harness provides centralized cable management with strain relief IMPORTANT Some flat panel displays reguire adapter kits which you can purchase from your authorized SMART reseller This chapter covers e Connecting Your Flat Panel Display page 18 e Connecting Your Computer page 21 Connecting Your SMART Hub PE260 page 23 e Connecting a DVD Blu ray Player or VCR page 25 Connecting Your SMART Board interactive display frame page 28 Connecting Your SMART Board for Flat Panel Displays Interactive Overlay page 32 1010651 Rev C1 18 MODEL FSSBID
75. o plug from cable AVO4 to the receptacle marked AUDIO In on your SMART Mobile Stand s connection panel Disconnect cable C05 from the USB receptacle marked with an image of a tower computer on your SMART Mobile Stand s connection panel and then connect it to an available USB receptacle on your laptop computer fg NOTES For convenience the SMART Mobile Stand for Interactive Displays Textless Installation Instructions smarttech com kb 132293 included with your unit instructs you to connect both ends of this USB A male to USB B male cable into your SMART Mobile Stand s connection panel For model FSSBID 100H the USB receptacle marked with an image of a tower computer on your SMART Mobile Stand s connection panel is a standard USB A connection for an external device Set your flat panel display s video input mode to RGB For more information refer to the documentation included with your flat panel display To connect your SMART Document Camera 63 COMPLETING YOUR INSTALLATION AND CONNECTING OTHER PRODUCTS TO YOUR SMART MOBILE STAND Connecting Your SMART Document Camera Your SMART Mobile Stand s rear connection panel enables you to easily connect your SMART Document Camera through a USB A connection and then present images from your document camera on your flat panel s screen IMPORTANT Connecting your SMART Document Camera to your SMART Mobile Stand as described in the following procedure enables basic document c
76. o plug from cable AVO5 included in your SMART Mobile Stand s accessory kit to adapter AD08 s VGA video receptacle Connect the 3 5 mm stereo audio plug from cable AV05 to your SMART Hub SE240 s remaining Computer Audio receptacle marked 2 Connect a USB A to USB B cable not included to the remaining USB B receptacle marked Computer 2 on your hub Connect your SMART Hub SE240 s power cable included with your hub to the receptacle marked 12V DC and then connect the other end to a free receptacle on your SMART Mobile Stand s power bar 1010651 Rev C1 1010651 Rev C1 46 MODEL FSSBID 100H CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET g TP Coil and bundle the cable with the included hook and loop fastener strap 2 Replace the shelves in your SMART Mobile Stand s cabinet See page 14 for details on installing the shelves in your SMART Mobile Stand Connecting Your Computer If you choose to install a computer with your SMART Hub SE240 your SMART Mobile Stand includes dedicated space for a tower computer behind the left cabinet door when your stand is configured for standard shelving Internal connections provide support for VGA video 3 5 mm stereo audio USB for interactive product touch control and two additional USB devices IMPORTANT You must connect your SMART Hub SE240 to your computer page 45 before you complete the following procedure The following procedure refers to these cables which
77. players you might choose to purchase a separate HDMI cable to replace cables A05 and V02 Install this HDMI cable along the same path as cables A05 and V02 See page 41 for details on connecting the other end of these cables to your flat panel display Ga TIPS Install your DVD or Blu ray player on the top shelf or the second highest rack mount position Install your VCR on the lowest shelf in your SMART Mobile Stand s cabinet To connect your 1 Connect the two plug RCA cable A05 or your HDMI DVD Blu ray player cable as follows EE Connect the red audio plug to your DVD Te or Blu ray player s appropriate red receptacle which is typically labeled R 1 n TA au E Connect the white audio plug to your DVD or Blu ray player s white receptacle which is typically labeled L S Video A NOTE 2 x RCA Pid Cable A05 V02 You previously connected the other end of this cable to your SMART Hub SE240 see page 44 2 Connect S Video cable V02 to the appropriate receptacle on your DVD or Blu ray player This receptacle is typically labeled S Video 1010651 Rev C1 49 MODEL FSSBID 100H CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET A NOTE You previously connected the other end of this cable to your SMART Hub SE240 see page 44 3 Connect your DVD or Blu ray player s power cable not i
78. puter IMPORTANT If you are using a guest laptop computer with your SMART Mobile Stand you will not be able to use either of the adjacent vertical USB A connections marked USB or the USB receptacle marked with an image of a tower computer FSSBID 100H only on your SMART Mobile Stand s connection panel see page 60 Do not route the receiver s USB cable around the same side of your SMART Mobile Stand as the height adjustment handle This cable could get in your way while you operate the handle Do not route the receiver s USB cable in any place on your SMART Mobile Stand where it could get pinched On Windows computers the Add Hardware Wizard appears On Mac computers a balloon message appears indicating that the hardware is ready to use The top LED indicator on the receiver turns solid red to indicate that it s receiving power A NOTE The remaining steps apply only to Windows computers 3 If the Found New Hardware wizard doesn t start automatically click Start gt Settings gt Control Panel gt Add Hardware 4 Select Yes this time only and then click Next 5 Click Next to start the hardware installation 6 Click Finish to complete the first installation cycle After a short delay the Add Hardware Wizard appears again 7 Repeat steps 4 through 6 A balloon message appears indicating that the hardware is ready to use The top LED indicator on the receiver turns solid red to indicate that it s receiv
79. r Flat Panel Displays Interactive Overlay Adapter Kit FSSBID 100 Only page 8 Rack Mount Hardware Accessory Kit page 8 e Standard Replaceable Parts page 8 1010651 Rev C1 1010651 Rev C1 2 ABOUT YOUR SMART MOBILE STAND SMART Mobile Stand Features Your SMART Mobile Stand is easy to move so that you can share the unit with other users reconfigure your meeting space or classroom or guickly add interactive and audiovisual features to a room that might otherwise not have them The height of your mobile floor stand adjusts guickly and smoothly to improve lines of sight and accommodate users of different heights including users with limited reach Feature Highlights Height Adjustment Your SMART Mobile Stand features a height adjustment range of 15 3 4 40 cm Easy Mobility Four swiveling heawy duty non marking casters roll easily on common indoor surfaces and lock into place so that your stand doesn t move when you use it Stable Design A wide footprint low profile base and reinforced steel design provide excellent stability when you re touching or writing on your interactive product Security A durable locking cabinet provides secure storage for audiovisual eguipment including a standard tower computer and features two vertically adjustable shelves an optional 19 48 cm rack mount configuration and lockable doors to help prevent theft Integrated Cable and Power Management A prewired cable bundle an i
80. rom right to left and then connect them to your SMART Board interactive display frame s controller box coiling the excess cable and fastening it to the speaker panel with cable ties as shown below g TIP Leave some slack throughout the length of these cables Don t pull them tight Cable Connections to Your SMART Board Interactive Display Frame Route camera cables up your SMART Mobile Stand s prewired cable harness down behind the speaker panel and along the inside edge of the pencil ledge Camera Camera Speaker Panel Coil and fasten the excess camera cables to the clips on the speaker panel with plastic cable ties Power Cable to Your Controller Box with Strain Relief Loop i Connect USB Cable C04 H to the controller box I creating a strain relief loop ie zle e and then fasten it to a clip FU J on the speaker panel with a plastic cable tie
81. s no responsibility and you are solely responsible for this damage Your SMART Mobile Stand supports USB 2 0 compliant devices and earlier You can also connect these USB devices directly to your computer Refer to the documentation you received with your computer keyboard or mouse for more information 67 MAINTAINING YOUR SMART MOBILE STAND Maintaining Your SMART Mobile stand Your SMART Mobile Stand is durable With proper care it will provide years of trouble free service This chapter covers e Cleaning and Preventing Damage to Your SMART Mobile Stand this page Moving Your SMART Mobile Stand page 68 Transporting Your SMART Mobile Stand page 68 Contacting SMART Technical Support page 68 Cleaning and Preventing Damage to Your SMART Mobile Stand M CAUTION Donotallow liquids spray cleaners or commercial solvents of any kind to flow into the connection panel Do not attempt to service your SMART Mobile Stand Only an authorized service provider should service your SMART Mobile Stand Disconnect your SMART Mobile Stand s power plug from the power outlet before cleaning the unit or if you won t be using it for a long period of time Use a soft cloth moistened with a mild detergent to clean the unit s housing If your SMART Mobile Stand requires replacement parts make sure that the service technician uses replacement parts specified by SMART Technologies 1010651 Rev C1 To determine your SM
82. surrounding obstacles D CAUTION To prevent damage to your power and extender cables secure them to your mobile floor stand as instructed in the SMART Mobile Stand for Interactive Displays Textless Installation Instructions smarttech com kb 132293 fj NOTES You will require ample work space to assemble your SMART Mobile Stand Do not set up or use your SMART Mobile Stand in an area with excessive levels of dust dirt humidity or smoke If you received an IEC power bar with your SMART Mobile Stand and you need to ground this power bar use a self tapping screw not included to secure its ground wire to the base sheet metal of your stand Use the small hole located on the right side of the power bar when viewed from the back for this purpose 1010651 Rev C1 1010651 Rev C1 12 ASSEMBLING YOUR SMART MOBILE STAND Installing Your Flat Panel Display on Your SMART Mobile Stand al WARNING Read the installation instructions published by your flat panel display s manufacturer before installing your flat panel display on your SMART Mobile Stand Make sure that you properly engage and secure the vertical brackets both to your flat panel display and to your SMART Mobile Stand as instructed in the SMART Mobile Stand for Interactive Displays Textless Installation Instructions smarttech com kb 132293 D CAUTION To prevent crushing additional product cables between your flat panel display and the SMART Mobile Stand s speak
83. tie and then secure this adapter cable to cable C04 with another plastic cable tie Power Cable to Your SMART Board for Flat Panel Displays Interactive Overlay s Pen Tray Power Cable to Power Supply 2 i E USB A to B Adapter ADO9 TIT lell se lt To connect your 1 Working inside your SMART Mobile Stand s cabinet from the back secure interactive overlay your interactive overlay s power supply to the two mounting holes directly to the right of the connection panel using plastic cable ties IMPORTANT Position this power supply so that the power cable is on the left side 2 Connect the power cable and connector from this power supply to your interactive overlay s power port TIPS Route this power cable through your SMART Mobile Stand s connection panel and up the prewired cable harness Leave some slack throughout the length of this cable Don t pull it tight 1010651 Rev C1 34 MODEL FSSBID 100 CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET 3 Connect the DB9 end of the SMART DB9 to USB adapter cable included with your SMART Board for Flat Panel Displays interactive overlay to your pen tray ensuring that you can still easily access the USB
84. to Your SMART Mobile Stand u San uu S DAMA deae alo vedeli ale 57 Installing the Rear Access Panels on Your SMART Mobile Stand 58 The Connection Panel mesrine u L L Lu k S uu nd IRR RE Ren e 59 Connecting a Guest Laptop Computer 61 Connecting Your SMART Document Camera 63 Connecting Your SMART Response formerly Senteo Interactive Response System Receiver aaa 64 Connecting Other USB Devices nan 66 Maintaining Your SMART Mobile Stand J 67 Cleaning and Preventing Damage to Your SMART Mobile Stand 67 Moving Your SMART Mobile Stand 68 Transporting Your SMART Mobile Stand 68 Contacting SMART Technical Support 68 A Configuring a Rack Mount 69 B SMART Mobile Stand Running Diagrams eee 75 C Hardware Environmental Compliance essen 85 Waste Electrical and Electronic Equipment Regulations WEEE Directive 85 Restriction of Certain Hazardous Substances RoHS Directive 85 Packagilig 5 uD PG pieces jaca Sein D a pad Pec RE 85 1010651 Rev C1 vii CONTENTS Covered Electronics Devices nan 86 China s Electronic Information Products Regulations 86 U S Consumer Product Safety Improvement Act 86 D Customer S ppoOlt nic
85. tory compliance See hardware environmental compliance replacement parts 67 RoHS directive 85 running diagram table 85 S security 2 Senteo interactive response system 64 servicing 2 shelving 14 shipping 68 1010651 Rev C1 91 INDEX SMART Board for Flat Panel Displays interactive overlay cable routing illustration 33 55 connecting 32 55 SMART Board for flat panel displays interactive overlay adapter 32 SMART Board for Flat Panel Displays interactive overlay adapter kit 8 SMART Board interactive display frame cable routing illustration 31 53 connecting 28 50 SMART Document Camera 63 SMART Hub PE260 23 cable connections illustration 24 connecting 23 SMART Hub SE240 23 connecting 43 installation 38 SMART Mobile Stand 7 2 SMART Technical Support 87 SMART technical support 68 stability 2 support 87 supported flat panel displays 7 T Technical Support 87 temperature operating 10 storage 70 training 87 transporting 68 troubleshooting articles 87 U U S regulations 86 USB cable 27 USB devices 66 USB flash drive 66 USB hub 22 USB key 66 user s guides 87 V VCR 25 48 connecting 27 49 installation 25 48 W warranty 87 water resistance 10 WEEE directive 85 92 INDEX 1010651 Rev C1 smarttech com support i smarttech com contactsupport 1010651 Rev C1
86. ur SMART Mobile Stand immediately after moving it from a cold location to a warm location Allow the unit to reach room temperature before operation to prevent possible product damage The operating temperature range is from 41 F to 86 F 5 C to 30 C with up to 80 relative humidity non condensing The shipping and storage temperature range is from 40 F to 140 F 40 C to 60 C Do not place your SMART Mobile Stand in hot locations such as near heating equipment 1010651 Rev C1 1010651 Rev C1 IMPORTANT INFORMATION Do not block the ventilation slots and openings on your SMART Mobile Stand Blocking these openings could cause overheating and damage to the unit When transporting your unit repack it with as much of the original packaging as possible This packaging was designed with optimal shock and vibration protection Do not allow liquids spray cleaners or commercial solvents of any kind to flow into the connection panel Do not attempt to service your SMART Mobile Stand Only an authorized service provider should service your SMART Mobile Stand If your wired keyboard mouse or other USB device is damaged while it is attached to your SMART Mobile Stand SMART assumes no responsibility and you are solely responsible for this damage Other Precautions If you own a SMART product other than your SMART Mobile Stand for interactive displays refer to the other product s documentation for relevant safety warnings an
87. with your interactive overlay to the right side of its power supply 1010651 Rev C1 35 MODEL FSSBID 100 CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET 7 Route the power cable through the connection panel from right to left behind the hydraulic pump and down the cabinet s rear support tube and then connect the other end to an available receptacle on your SMART Mobile Stand s power bar TIP Coil and bundle the excess cable with the included hook and loop fastener strap m NOTES Don t connect your SMART Mobile Stand to a power outlet before you install the rear access panels page 58 If you move your SMART Mobile Stand with a SMART Board for Flat Panel Displays interactive overlay installed secure the pens in the pen tray so that they don t fall out 1010651 Rev C1 36 MODEL FSSBID 100 CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET 1010651 Rev C1 37 MODEL FSSBID 100H CONNECTING DEVICES INSIDE YOUR SMART MOBILE STAND S CABINET Model FSSBID 100H Connecting Devices Inside Your SMART Mobile Stand s Cabinet This chapter explains how to connect your SMART Mobile Stand FSSBID 100H s prewired cable harness to your flat panel display SMART Hub SE240 computer and other devices inside your stand s cabinet Your stand s cable harness provides centralized cable management with strain relief IMPORTANT Some flat panel displays reguire adapter kits which you can purchase from

Download Pdf Manuals

Related Search

Related Contents

Samsung SCC-B5310 User's Manual    micrófono amplificador microphone with amplifier micro  Parkside XQ2 SE Sander User Manual    Combi (E) CP plus ready  AFtRIV ÉE - Communauté d`agglomération de Cergy  SIARETRON 3000 ICU  Ural (Урал) - Dnepr ( Днепр) Russian Motorcycle  PBH-101 User Manual  

Copyright © All rights reserved. Failed to retrieve file