Kingston Technology HyperX KHX2000C9AD3T1FK3/6GX 6GB 2000MHz
Contents
1. Core inside Kingston Memory Module Specification OLOGY KHX2000C9AD3T1FK3 6GX 6GB 2GB 256M x 64 Bit x 3 pcs DDR3 2000MHz CL9 240 Pin DIMM Kit w Fan DESCRIPTION Kingston s KHX2000C9AD3T1FK3 6GX is a kit of three 256M x 64 bit 2GB 2048MB DDR3 2000MHz CL9 SDRAM Synchronous DRAM memory modules based on sixteen 128M x 8 bit DDR3 FBGA components per module Each module kit supports Intel XMP Extreme Memory Profiles Total kit capacity is 6GB Each module kit has been tested to run at DDR3 2000MHz at a low latency timing of 9 11 9 at 1 65V The SPDs are programmed to JEDEC standard latency DDR3 1333MHz timing of 9 9 9 at 1 5V Each 240 pin DIMM uses gold contact fingers and requires 1 5V The JEDEC standard electrical and mechanical specifications are as follows This special kit part number includes Kingston s HyperX high performance cooling fan assembly KHX FAN FEATURES JEDEC standard 1 5V 0 075V Power Supply VDDQ 1 5V 0 075V 667MHz fCK for 1333Mb sec pin 8 independent internal bank Programmable CAS Latency 5 6 7 8 9 10 Posted CAS Programmable Additive Latency 0 CL 2 or CL 1 clock Programmable CAS Write Latency CWL 7 DDR3 1333 8 bit pre fetch Burst Length 8 Interleave without any limit sequential with starting address 000 only 4 with tCCD 4 which does not allow seamless read or write either on the fly using A12 or MRS Bi directio2. MANCE Rated Voltage Operational Voltage Input Current Input Power RPM Speed Control Type Signal Output Max Air Flow At Zero Static Pressure Max Air Pressure At Zero Flow K K SEEEEEES Accoustical Noise Document No 4805507 001 A00 HyperX Cooling Fan Assembly 12 VDC 8 13 5 VDC 0 09 amp 1 08 watt 3000 10 Frequency Generator FG 0 43 m min 15 02 CFM 2 31 mm H20 0 09 inch H20 25 28 max dB A Page 3 Kingston ASSEMBLY q D x lt E lt i D po E Z c A Document No 4805507 001 A00 Page 4 Kingston DIMENSIONS Document No 4805507 001 A00 Page 5 Kingston INSTALLATION Step 1 Power the computer system off disconnect the AC power cord and remove the computer cover Step 2 To assemble the HyperX fan secure the two side brackets with the four thumb screws washers Do not tighten the screws completely Step 3 Swing the retaining brackets open and slide the assembly over the HyperX modules as shown in the illustration Rest the base of the brackets onto the memory socket lock tabs Document No 4805507 001 A00 Page 6 Kingston INSTALLATION cont Step H4 Simultaneously apply pressure to both retaining brackets and tighten down all four thumb screws Step 5 Locate the fan power source on the motherboard and connect the HyperX fan power cable Step 6 Reconnect the AC power cord E a
3. nal Differential Data Strobe Internal self calibration Internal self calibration through ZQ pin RZQ 240 ohm 1 On Die Termination using ODT pin Average Refresh Period 7 8us at lower then TCASE 85 C 3 9us at 85 C lt TCASE 95 C Asynchronous Reset PCB Height 2 401 61 00mm w heatsink double sided component PERFORMANCE CL IDD 9 cycles Row Cycle Time tRCmin 49 5ns min Refresh to Active Refresh Command Time tRFCmin 110ns Row Active Time tRASmin 36ns min Power 1 800 W operating per module UL Rating 94 V 0 Operating Temperature 0 C to 85 C Storage Temperature 55 C to 100 C Document No 4805507 001 A00 03 04 10 Page 1 Kingston MODULE DIMENSIONS r 133 35 30 00 Units millimeters 18 80 15 80 11 00 8 00 O DOD TEE ADD 00000000 w fu I00000000000000 Il JOO0OOODOOODODODDI O 0 00 0 00 54 70 w heatsink assembly Document No 4805507 001 A00 Page 2 KHX FAN Kingston HyperX Cooling Fan Assembly DESCRIPTION This document describes Kingston s HyperX memory module cooling fan assembly If you are looking to maximize the performance potential of your HyperX memory this is it With twin fans focusing air directly onto your HyperX modules your modules will run cooler even in the most demanding environments The mechanical and electrical specifications are as follows PERFOR
4. nd power up the computer to verify fan operation Replace the computer cover Document No 4805507 001 A00 Page 7
Download Pdf Manuals
Related Search