Western Digital Caviar RE3, 1 TB, 1.2 million/h MTBF, 32 MB Cache, 7200 RPM
Contents
1. Western Digital Before Getting Started This poster is designed to aid in the quick installation of your WD SATA hard drive If you experience problems following these procedures or need further information regarding your drive visit support wdc com to search our online knowledge base for frequently asked questions and other common troubleshooting tips and to download the full version WD SATA Hard Drive Installation Guide Necessary materials and tools Computer system manual Operating system manual Operating system installation CD Phillips and flat blade screwdrivers if applicable WD SATA Hard Drive Quick Install Guide 1 Before performing any hardware installation back up Kit Contents j your existing data 2 Before handling the drive or system components discharge static electricity by touching the metal chassis of your computer case or using an antistatic wrist strap 3 Locate the WD serial number model number and date code on the label on top of your drive and record them below WD SATA Cable with SecureConne ct for use only with WD S ATA hard drives S e ri a N um be r 4 Power down the computer and unplug the power cord 5 Remove the system cover refer to your system manual for instructions Documentation Data Lifeguard Tools CD for WD 7200 RPM SATA hard drive kits Unpacking and Handling Procedures2. View Installation Tutorial Create view and print a customized installation manual Set Up Your Hard Drive Partition and format an installed hard drive Drive to Drive Copy Copy all the files or a specific folder from one hard drive to another set a specific hard drive size Hard Drive Information Configure jumper settings and other technical information regarding your hard drive Register Your Hard Drive Register your hard drive online Internet connection required Set Up Your Hard Drive This section contains instructions for installing your new WD hard drive either as a new boot drive or as an additional storage drive Install a New Boot Drive 1 Insert the Data Lifeguard Tools CD into your CD ROM drive a If using the Windows version the CD autoruns on your desktop b If using the DOS version restart the computer and boot from the CD 2 Select Run Data Lifeguard Installation Software from the autorun setup menu 3 The main menu shown below appears after Data Lifeguard Tools is loaded Click Set Up Your Hard Drive from the list of options Data Lifeguard may take several moments to scan for system devices i Set Up our Hard Drive will ask you to select a specie largei dive will ask a lew questions aboul fa nd to use your new hard drive and then A and formal the direc according to your Y 4 After Data Lifeguard Tools detects your installed hard drive s select the n
3. Default 1 or Default 2 see below set as the standard configuration Standard configuration 1 no jumper added spread Standard configuration 2 jumper across pins 1 2 spread spectrum clocking disabled spectrum clocking disabled Default 2 Default 1 DO NOT change the default setting if you intend to use the drive in a desktop computer Change the jumper settings ONLY if you intend to use the drive in an enterprise storage environment For more information on these advanced settings obtain the full version WD SATA Installation Guide at support wdc com ee Neutral storage placement In this position the jumper has no effect on hard drive operation SSC_DIS Mode Default Enable or disable the spread spectrum clocking feature Default setting is disabled Spread spectrum clocking enabled OPT1 Only for factory use OPT2 Only for factory use KEY Jumper pins H Jumper added Install the SATA Hard Drive IMPORTANT Only for WD 7200 RPM SATA hard drive kits all other WD SATA hard drive kits skip to step 1 below Serial ATA Serial ATA Legacy ATA power connection interface power connection connection If installing your new WD drive as an upgrade from a previously installed hard drive To ensure the optimal settings for your drive configuration WD recommends running the Installation Tutorial in the Windows version of Data Lifeguard Tools before hardware insta
4. specifications technical tips and the online forum System Requirements SATA interface connector on motherboard or SATA controller card sold separately installed in an available 32 bit PCI expansion slot 2 1 or 2 2 compliant Knowledge Base Explore our expert knowledge base and frequently asked questions FAQs Service Partners Find available WD approved service and support in your region Do not stack hard drives or stand your WD drive on tts edge Do not drop shake or knock down the hard drive Contact Support Contact a support representative by 3 5 inch internal drive bay l phone or e mail Save the original packaging materials and antistatic bag in case you need to return your hard drive Your warranty will be void if your returned drive is shipped in anything other than the original packaging or WD approved materials Rebates Check the status of rebate submissions Online Product Registration Take advantage of WD offerings by registering your drive at https www westerndigital com en products registration Localized Support Display service and support information in various languages Set the Jumpers The default setting for WD SATA hard drives varies depending on the model To determine the default setting for your drive look at the drive label on the top of the drive Note WD SATA drives ship from the factory with either
5. Drive setup steps to be completed z complain 9 Remove the Data Lifeguard Tools CD from the CD ROM drive and choose from the following options a Ifinstalling Windows insert the Windows installation CD in the CD ROM drive and restart the system Follow the on screen instructions to install the operating system b If an operating system is already been installed restart the system This concludes the hard drive setup process Your WD SATA hard drive is now ready to use Install an Additional Storage Drive 1 Insert the Data Lifeguard Tools CD into your CD ROM drive a If using the Windows version the CD autoruns on your desktop b Ifusing the DOS version restart the computer and boot from the CD 2 Select Run Data Lifeguard Installation Software from the setup menu 3 The main menu appears after Data Lifeguard Tools is loaded Click Set Up Your Hard Drive from the list of options Data Lifeguard Tools may take several moments to scan for system devices Hard Drive Information This feature allows you to view the drive model number serial number capacity UDMA mode and other details about your WD SATA hard drive 1 Insert the Data Lifeguard Tools CD into your CD ROM drive Select Hard Drive Information from the main menu In the next window you are given options to select either View Hard Drive Information or View Jumper Settings a View Hard Drive Information Once your drive is detected clic
6. Right click your new hard drive to proceed with partitioning and formatting Windows 2000 Click the Start button and point to Settings gt Control Panel gt Administrative Tools Double click the Computer Management icon and select Disk Management on the left side Right click your new hard drive to proceed with partitioning and formatting
7. WD hard drives are precision instruments and must be handled with care during unpacking and installation Hard drives can be damaged by rough handling shock and vibration or electrostatic discharge ESD Be aware of the following precautions Operating Systems _ WARNING _ Using an operating system not listed below may result in data loss Technical Support If you need additional information or help during installation or normal use of this product visit our product support Web site at support wdc com and choose from these topics Warranty Services Obtain warranty information warranty status extended warranty product replacement RMA status and shipping and packaging information Do not unpack your hard drive until you are ready to install it Your hard drive is packaged in an anti static bag The following operating systems are supported Windows XP Windows 2000 Handle the hard drive only by the sides Avoid touching circuit i Downloads Library Download installation software board components on the bottom of the drive and drivers To avoid ESD problems ground yourself by touching the metal chassis of the computer or by wearing a grounding strap before handling the hard drive Articles of clothing generate static electricity Do not allow clothing to come in direct contact with the hard drive or circuit board components Technical Information Access product
8. age of malabis njia E FATE 7 The next screen outlines your setup options number of partitions file format and the size of each partition Data Lifeguard Tools is now ready to set up your new hard drive Click Erase then Next CAUTION Continuing will erase all existing data on the hard drive If you are certain click Yes to proceed with format and partition 8 After Data Lifeguard Tools completes formatting and partitioning the drive the setup summary screen outlines all steps completed Click Done to exit 9 Remove the CD from the CD ROM drive to begin using your new WD hard drive as additional storage A new drive letter and icon appear under My Computer This concludes the hard drive setup process Your WD SATA hard drive is now ready to use Alternate Instructions for Installing a Drive Windows XP 2000 If your hard drive kit does not include a Data Lifeguard Tools CD you can use Windows built in Disk Management utility to format and partition your drive If necessary refer to your operating system manual for detailed instructions Install a Single Hard Drive 1 Boot from the Windows XP or Windows 2000 Installation CD 2 Follow the directions as prompted Install an Additional Hard Drive Windows XP Click the Start button and point to Control Panel gt Performance and Maintenance gt Administrative Tools Double click the Computer Management icon and select Disk Management on the left side
9. ew drive to be formatted or partitioned as the new boot drive and click Next If you are using a SATA controller card click the Additional Controllers tab to select your new drive NOTE Data Lifeguard Tools does not format or partition a currently installed boot drive the drive icon is disabled 5 For Installation Type select Add the drive as a boot device To create customized partitions select the box to change advanced options and check Custom Partition 6 The Custom Partition Setup screen appears Your hard drive is automatically partitioned to the largest capacity based on your operating system limitations If the drive contains existing partitions and you want to create or add partitions you must first click Delete to remove existing partitions To add partitions use the slider bar to size the partition then click Add Partition After setting the partitions click Next Drive to Drive Copy Both source and destination hard drives must be formatted and partitioned before using this utility Follow the instructions above to set up your drive The Drive to Drive Copy utility copies files from one drive to another Use this feature when replacing an existing boot hard drive with a newer faster hard drive 1 Insert the Data Lifeguard Tools CD into your CD ROM drive Select Drive to Drive Copy from the main menu Select the Source and Destination paths with the selected folders You can click Browse to easily access folde
10. ive with the four mounting screws two on each side For proper grounding install the screws in the hole positions as shown 4 Verify all cable connections Replace and secure the system cover Reconnect the power cord and power up the computer 5 If your WD SATA drive came with a Data Lifeguard Tools CD see Set Up Your Hard Drive on the reverse side of this poster to set up your new hard drive If your hard drive kit did not include a Data Lifeguard Tools CD see Alternate Instructions for Installing a Drive on the reverse side of this poster 3 5 inch Floppy Drive Power Supply SATA Motherboard Configuration SATA Controller Card Configuration Using Data Lifeguard Tools IMPORTANT If your hard drive kit does not include a Data Lifeguard Tools CD skip to Alternate Instructions for Installing a Drive Windows XP 2000 You can also obtain the latest version of Data Lifeguard Tools from our Web site at support wdc com WD s Data Lifeguard Tools assists with hard drive installation management and diagnostics Depending on your setup and configuration you can use either the Windows or DOS version of Data Lifeguard Tools NOTE Windows and DOS versions of Data Lifeguard Tools may vary slightly from one another in text graphic placement or color Data Lifeguard Tools contents Create a Bootable Diskette Create a bootable diskette in seconds
11. k the tab for either Partition Table or SATA Information to display information about the drive format LBA support DMA support firmware revision etc View Jumper Settings Select the drive model number and configuration then click View Jumper Settings to display the selected jumper setting diagram in your default Web browser Create a Bootable Diskette Follow these steps to create a bootable diskette using Data Lifeguard Tools 1 Insert the Data Lifeguard Tools CD into your CD ROM drive a If using the Windows version the CD autoruns on your desktop b If using the DOS version restart the computer and boot from the CD 2 When the autorun menu appears select Create a Data Lifeguard Bootable Installation Diskette Follow the directions as prompted View Installation Tutorial Follow these steps to create and print custom hardware installation instructions NOTE The model number of your hard drive is printed on the label on top of the drive 1 Insert the Data Lifeguard Tools CD into your CD ROM drive a If using the Windows version the CD autoruns on your desktop b If using the DOS version restart the computer and boot from the CD 2 Select View Installation Tutorial from the setup menu 3 Depending on whether you run the Windows or DOS version Data Lifeguard Tools may prompt you to select your model number or a hard drive configuration If your hard drive is not listed you can manually type in the model numbe
12. llation to generate your custom installation instructions See Data Lifeguard Tools on the reverse side of this poster aaa Z Legacy ATA power connector WD SATA cable with SecureConnect 1 Connect the smaller connector on the WD SATA cable to the SATA connector on the 2 Attach the larger end of the WD SATA cable motherboard or SATA controller card directly to the SATA interface on the back of the WD drive as shown above SATA connectors are keyed to ensure proper insertion Also attach the legacy 4 pin power connector The WD SATA cable with SecureConnect does not supply power to the drive When using the WD SATA cable you must also attach the legacy ATA 4 pin power connector to the SATA drive When using a standard SATA interface cable not included instead DO NOT connect both the standard SATA cable not included and legacy ATA 4 pin power cable at the same time or the drive may malfunction NOTE If using a SATA controller card be sure to follow the instructions that came with the card to install SATA host drivers SATA cable connection Motherboard 5 25 inch Bay Motherboard a WD SATA cable Z Hard Drives in 3 5 inch Bay Expansion Slot Mounting Frame CD ROM Drive SATA Controller Card SATA Connector on Controller Card Faceplate i MWA Ve Ne 3 Slide the hard drive into an available 3 5 inch drive MOUNTING THE HARD DRIVE bay and secure the dr
13. r Follow the instructions as prompted to create your 4 If using the Windows version your default Web browser opens automatically and displays your custom instructions If using the DOS version your instructions are displayed in the window Click Next to print the instructions 4 After detecting your installed hard drives select the drive to be formatted or partitioned as additional storage and click Next If you are using a SATA controller card click the Additional Controllers tab to select your new drive 5 For Installation Type select Add the drive as an additional device To create customized partitions select the box to change advanced options and check Custom Partition 6 The Custom Partition Setup screen shown below appears Your hard drive is automatically partitioned to the largest capacity up to 137 GB based on your operating system limitations If the drive contains existing partitions and you want to create or add partitions you must first click Delete to remove existing partitions To add partitions use the slider bar to set the desired partition size then click Add Partition After configuring the partitions click Next Western Digital iom Partition Setup fer WDC WEIR Oe PL iibi ME IF the dive conima emiibng pertiiond and pou wah bo create on add parihions you mut fret cick Teete bo deee miira patim Tosd punta weber Chee gida Buse ba sira iter puti then chek Yuki Patin Ther tider har shit the percent
14. rs or files on both hard drives NOTE Existing files on the destination drive are overwritten if there are files on the source drive with the same name After selecting the folder for each path click Start to begin copying The progress bar for the current file being copied and overall progress Is displayed When copying is completed click OK to display the results summary Click Done to exit Data Lifeguard Tools Remove the CD and restart the computer to use your new WD hard drive custom instructions 7 The next screen outlines your setup options number of partitions file format and the size of each partition Data Lifeguard Tools is now ready to set up your new hard drive Click Erase then Next to continue CAUTION All existing data on the hard drive will be erased lf you are prompted to continue click Yes to proceed 8 After Data Lifeguard Tools completes formatting and partitioning the drive the setup summary screen below outlines all steps completed Click Done to exit E eo Data Lifeguard Tools myne The information below shows Ihe steps completed and lhe seps remaining in the setup of your haw dive Western Digital Congratulations You have supcesetully installed Drive model WOC WO2S00R ROOD setup summary pantioned and fomnatied your new head drive tive selup steps completed Panitioned drive Click Dene to clone Data Litequard and eian using dine Fomalled dive your retry drone
Download Pdf Manuals
Related Search