Samsung 2263DX 22" UbiSync LCD
Contents
1. Entering the BIOS Setup screen may differ for each BIOS company Refer to the user manual for your PC For more information visit the Microsoft website My computer is on and the LED is blinking However only a blank screen is dis played on the monitor Q Check whether your computer is in hibernation mode The monitor turns off A Move your mouse or press any key to display the screen again Check the following items if there is trouble with the monitor Check if the power cord and the video cables are properly connected to the computer Check if the computer beeps more than 3 times when booting If it does request an a service for the main board of the computer If you installed a new video card or if you assembled the PC check if the installed the adapter video driver and the monitor driver Q amp A Troubleshooting Check if the scanning ratio of the video screen is set to between 56 Hz 75 Hz Do not exceed 75 Hz when using the maximum resolution If you have problems in installing the adapter video driver boot the computer in Safe Mode remove the Display Adapter in the Control Panel System Device Administrator and then reboot the computer to reinstall the adapter video driver Note If problems repeatedly occur contact an authorized service center How can I change the frequency A The frequency can be changed by reconfiguring the video card A Note that video card support can vary depe2. Introduction Package Contents L Note Please make sure the following items are included with your monitor If any items are missing contact your dealer Contact a local dealer to buy optional items Unpacking Without stand With stand USB Monitor Manuals Quick Setup Guide Warranty Card User s Guide Not available in all loca tions Cables D Sub Cable Power Cord USB Cable USB Cable Sold separately DVI Cable HDMI Cable Headphones Introduction Others Cleaning Cloth EA Note This is only provided for highly polished black products as a product feature Your Monitor Initial Settings The optimal resolution for this monitor is as follows kite kA HEt 117 Follow the above settings to set the resolution Language Select the language using the up or down key The displayed content will disappear after 40 seconds Turn the Power button off and on It will be displayed again It can be displayed up to three 3 times Make sure to adjust the resolution of your PC before reaching the maximum count Note The resolution displayed on the screen is the optimal resolution for this product Adjust your PC resolution so that it is the same as the optimal resolution for this product Front SAMSUNG Introduction 1 MENU button MENUAID Opens the on screen menu and exits from the menu Also use to exit the OSD menu or return to the previous menu 2 Customized Key
3. You can customize key assignment for the Custom button according to your pref erences Note You can configure the Customized key for a required function via Setup gt Cus tomized Key 3 Volume button When OSD is not on the screen push the button to adjust volume gt gt Click here to see an animation clip Adjust buttons WF A Adjust items in the menu O SOURCE button Enter button Push the SOURCE then selects the video signal while the OSD is off When the SOURCE button is pressed to change the input mode a message appears in the upper left of the screen displaying the current mode analog or digital input signal Activates a highlighted menu item Note If you select the digital mode you must connect your monitor to the graphic card s DVI port using the DVI cable gt gt Click here to see an animation clip amp AUTO button Use this button for auto adjustment Available in Analog mode only gt gt Click here to see an animation clip O Power button 6 Power indicator Use this button for turning the monitor on and off This light glows blue during normal operation and blinking blue once as the monitor saves your adjustments 7 Camera Using this camera you can view and send video for video chatting 8 Mic Using this microphone you can view and send audio for video chatting Speaker You can hear sound by connecting the soundcard of your PC to the monit
4. all the phone number on the Information section or contact your dealer
5. ck or external hard disk drive by connecting them to the amp DOWN port of the monitor without connecting them to the PC The USB port of the monitor supports High Speed Certified USB 2 0 High speed Full speed Low speed Data Rate 480 Mbps 12 Mbps 1 5 Mbps Power Consumption 2 5 W 2 5 W 2 5 W Max each port Max each port Max each port GAMSUNG Connect the S UP port of the monitor and the USB port of the computer with the USB cable Note To use DOWN port you have to connect the UP Upstream Cable to the PC Make sure to use the USB cable supplied with this monitor to connect the monitor s UP port and your computer s USB port Connect the DOWN port of the USB monitor and a USB device with the USB cable 3 The use procedures are as the same as those for using an external device connecting to the PC e You can connect and use a keyboard and mouse Connections e You can play a file from a media device Examples of media devices MP3 digital camera etc e You can run move copy or delete the files on the storage device Examples of storage devices external memory memory card memory reader HDD type MP3 player etc e You can use other USB devices that can be connected to a computer Note When connecting a device to the S DOWN port of the monitor connect the device using a cable appropriate to the device For the purchase of the cable and external devices ask
6. destroyed Tilt angle Using You can adjust the tilt angle within a range of 5 forward to 12 backward for the most comfortable viewing angle Attaching a Base This monitor accepts a 100 mm x 100 mm VESA compliant mounting interface pad Connections Monitor Mounting interface pad Sold separately L 2 Turn off your monitor and unplug its power cord Lay the LCD monitor face down on a flat surface with a cushion beneath it to protect the screen Remove four screws and then remove the stand from the LCD monitor Turn the armrest holder upwards or downwards Remove the screws on the armrest holder and remove it Align the mounting interface pad with the holes in the rear cover mounting pad and secure it with four screws that came with the arm type base wall mount hanger or other base AN e Do not use screws longer than the standard dimension as they may damage the inside of the Monitor e For wall mounts that do not comply with VESA standard screw specifications the length of the screws may differ depending on their specifications e Do not use screws that do not comply with the VESA standard screw specifica tions Do not fasten the screws too tightly as this may damage the product or cause the product to fall leading to personal injury Samsung is not liable for these kinds of accidents e Samsung is not liable for product damage or personal injury when a non VESA or non specified wall mou
7. e Hardware acceleration setting for your USB monitor in the Display Properties window A Set the Hardware acceleration value to Full For more information on how to configure the settings click here 1 Right click the Windows Desktop and click on Properties 2 The Display Properties window appears Select the Settings tab and click on Advanced 3 If the Properties window for your monitor is displayed select the Troubleshoot tab Move the Hardware acceleration slide to Full My USB monitor is connected but the screen is blank Q Does the Auto Installation program run when your USB monitor is connected A Install the USB Monitor Driver from the provided CD For more information on how to install the driver refer to Installing and Using the Software have connected the USB monitor but it does not boot up Q For the One Board Type computer which uses an 1815 chipset motherboard change the Legacy USB support option to Disabled in the BIOS Setup menu and reboot the computer A Example Phoenix BIOS If you turn on the computer the Press F2 to enter SETUP message is displayed on the bottom of the screen Press F2 to display the BIOS Setup menu A Configuring the Settings Set the Advanced gt Peripheral Configuration Integrated Peripherals gt Legacy USB Support item to Enabled Save the settings and reboot the computer A
8. e list and click Remove The screen size of the USB monitor is larger than the actual monitor size If the primary monitor has a high resolution screens are expanded beyond the recommended resolution in Clone mode USB monitor Q The screen size of the USB monitor is smaller than the actual monitor size The screen is centered on the monitor A Ifthe primary monitor has a high resolution screens are smaller than the recommended resolu tion in Clone mode USB monitor Q I disconnected or turned off my USB monitor but my PC still displays the old monitor infor mation in the Display Properties window A The deactivated USB monitors are such that the power to them is turned off or their USB cables are disconnected To remove this information you have to remove the Samsung Ubisync Mon itor program from Add Remove Programs in the Control Panel If you remove the program you cannot use all the connected USB monitors If you want to use the USB monitor again you have to setup the installation program again Q Icons and photos are broken or jagged in Clone mode USB monitor This occurs because Windows does not send the screen updating information to Clone mode if Extended mode is active on a single PC We recommend using the monitor in Extend mode Note Before calling for assistance check the information in this section to see if you can remedy any prob lems yourself If you do need assistance please c
9. er of gravity of the product resulting in the product falling causing product damage or personal injury 2 When adjusting the angle of the USB auxiliary monitor stand do not use too much force This may cause the stand to break Connections 3 Make sure to use the 7 USB monitor after properly adjusting the angle of its stand This may cause the center of gravity of the product to change leading causing the product to fall resulting in damage or a malfunction 4 When moving a 7 USB monitor take care not to knock the monitor against something The monitor may become scratched When disassembling the 7 USB monitor remove it by holding the part and pushing it in the direction of the arrow Connecting Headphone Note You may connect your headphones to the monitor SAMSUNG Connections 1 Connect your headphones to the Headphone connection terminal Connecting MIC P note You may connect your microphone to the monitor SAMEUNE 1 Connect the microphone cable to the MIC port on the monitor Using the Stand Monitor Assembly Simple Stand Monitor and Bottom Connections Swivel stand Using You can swivel the monitor left and right at an angle of 350 to set the monitor lengthwise The rubber under the stand is to avoid the monitor slide When you try to rotate the monitor in the state of the power cord or cable connecting to the monitor the power cord of cable can be
10. ged after changing the video card Q A Have the Windows colors been set properly Windows XP Set the resolution at the Control Panel Appearance and Themes Display Settings Windows ME 2000 Set the resolution at the Control Panel Display Settings Has the video card been set properly Set the video card by referring to the video card manual There is a message that reads Unrecognized monitor Plug amp Play VESA DDC monitor found Q A Q A Have you installed the monitor driver Install the monitor driver according to the Driver Installation Instructions See the video card manual to see if the Plug amp Play VESA DDC function can be supported Install the monitor driver according to the Driver Installation Instructions There is no image on the screen cannot turn on the monitor Q A Check whether the USB cable is connected correctly Check whether the USB driver is installed The USB monitor is recognized as a general USB device on a PC If you turn the monitor on or off quickly and repeatedly a USB device problem may occur Refer to the USB device Trou bleshooting section on the Microsoft customer support website 1 Right click the My Computer and click on Properties 2 The Device Manager is displayed 3 From the Action menu click Scan for hardware changes Reboot your PC Troubleshooting The screen of the USB monitor freezes Q Check th
11. he phone number on the Information section or contact your dealer No images on the screen cannot turn on the monitor Q A Q A Is the power cord connected properly Check the power cord connection and supply Can you see Check Signal Cable on the screen Connected using the D sub cable Check the signal cable connection Connected using the DVI cable If you still see an error message on the screen when the monitor is connected properly check to see if the monitor status is set to analog If you still see an error message on the screen when the monitor is connected properly check to see if the monitor status is set to analog Press SOURCE button to have the monitor double check the input signal source If the power is on reboot the computer to see the initial screen the login screen which can be seen If the initial screen the login screen appears boot the computer in the applicable mode the safe mode for Windows ME XP 2000 and then change the frequency of the video card Refer to the Preset Timing Modes If the initial screen the login screen does not appear contact the Service Center or your deal er Can you see Not Optimum Mode Recommended Mode 1680 x 1050 60 Hz on the screen You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can handle properly Adjust the maximum resolution and frequency that the monit
12. laying only one color as if looking at the screen through a cellophane paper Check the signal cable connection Make sure the video card is fully inserted in its slot Have the screen colors become strange after running a program or due to a crash between ap plications Reboot the computer Has the video card been set properly Set the video card by referring to the video card manual The screen suddenly has become unbalanced Q A Q A Have you changed the video card or the driver Adjust screen image position and size using the OSD Have you adjusted the resolution or frequency to the monitor Adjust the resolution and frequency at the video card Refer to the Preset Timing Modes Q Troubleshooting The screen can be unbalanced due to the cycle of the video card signals Readjust Position by referring to the OSD The screen is out of focus or OSD cannot be adjusted Q A Have you adjusted the resolution or frequency on the monitor Adjust the resolution and frequency of the video card Refer to the Preset Timing Modes LED is blinking but no images on the screen Q A Is the frequency properly adjusted when checking the Display Timing on the menu Adjust the frequency properly by referring to the video card manual and the Preset Timing Modes The maximum frequency per resolution may differ from product to product There are only 16 colors shown on the screen The screen colors have chan
13. nding on the version of the driver used Refer to the computer or the video card manual for details How can I adjusts the resolution A Windows XP Set the resolution in the Control Panel Appearance and Themes Display Settings A Windows ME 2000 Set the resolution in the Control Panel Display Settings Contact the video card manufacturer for details How can I set the Power Saving function Windows XP Set the resolution in the Control Panel Appearance and Themes Display Screen Saver Set the function in the BIOS SETUP of the computer Refer to the Windows Computer Man ual A Windows ME 2000 Set the resolution at the Control Panel Display Screen Saver Set the function in the BIOS SETUP of the computer Refer to the Windows Computer Man ual How can I clean the outer case LCD Panel Disconnect the power cord and then clean the monitor with a soft cloth using either a cleaning solution or plain water Do not leave any detergent or scratches on the case Do not let any water enter the monitor How I can clone or extend screen mode A Open the Display Properties window and select the Settings tab Q How can I remove the USB Monitor Installation Program completely Troubleshooting A Click Add Remove Programs in the Control Panel A list of currently installed programs is displayed Select Samsung UbiSync Monitor from th
14. nt is used or the consumer fails to follow the product installation instructions A e To mount the monitor on a wall you should purchase the wall mounting kit that allows you to mount the monitor at least 10 cm away from the wall surface e Contact the nearest Samsung Service Center for more information Samsung Electronics will not be responsible for damages caused by using a base other than those specified e Please use Wall Mount according to the International standards Troubleshooting Self Test Feature Check A Note Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly Self Test Feature Check 1 Turn off both your computer and the monitor 2 Unplug the video cable from the back of the computer 3 Turn on the monitor If the monitor 1s functioning properly you will see a box in the illustration below Check Signal Cable This box appears during normal operation if the video cable becomes disconnected or damaged 4 Turn off your monitor and reconnect the video cable then turn on both your computer and the monitor If your monitor screen remains blank after using the previous procedure check your video controller and computer system your monitor is functioning properly Warning Messages If there is something wrong with the input signal a message appears on the screen or the screen goes blank although the power indicator LED is still on The message ma
15. or Rear Introduction You can only hear sound from this monitor model if it is connected to a PC via a USB cable Use this button to decrease the screen brightness for the 7 USB monitor The LED blinks when the screen brightness is decreased to the minimum or when a screen brightness adjustment is completed A G Use this button to increase the screen brightness for the 7 USB monitor The LED blinks when the screen brightness is increased to the maximum or when a screen brightness adjustment is completed 12 Power button Power indicator Press the Power button to turn the 7 USB monitor on or off The Power indicator is displayed in blue when operating normally Note Please activate the afterimage prevention function before using the 7 USB auxiliary monitor Activating the function Turn off the USB monitor and hold down the Power button for five 5 seconds The monitor is turned on again and the afterimage prevention program is ac tivated while the LED blinks twice Deactivating the function Turn off the USB monitor and hold down the Power button for five 5 seconds The monitor is turned on again and the afterimage prevention program is de activated while the LED blinks once What is the afterimage prevention function If you use the USB auxiliary monitor with the same image remaining on the screen for a long period of time an afterimage may develop on the panel The afterimage preven
16. or can handle properly Troubleshooting If the display exceeds WSXGA or 75 Hz a Not Optimum Mode Recommended Mode 1680 x 1050 60 Hz message is displayed If the display exceeds 85 Hz the display will work properly but the Not Optimum Mode Recommended Mode 1680 x 1050 60 Hz message appears for one minute and then disappears Please change to the recommended mode during this one minute period The message is displayed again if the system is rebooted There is no image on the screen Is the power indicator on the monitor blinking at 1 second intervals The monitor is in PowerSaver mode Press a key on the keyboard to activate the monitor and restore the image on the screen If there is still no image press the SOURCE button Then press any key on the keyboard again to activate the monitor and restore the image on the screen Connected using the DVI cable You may get a blank screen if you boot the system before you connect the DVI cable or dis connect and then reconnect the DVI cable while the system is running as certain types of graphic cards do not send out video signals Connect the DVI cable and then reboot the system cannot see the On Screen Display Q A Have you locked the On Screen Display OSD Menu to prevent changes Unlock the OSD by pressing the MENU Ul button for at least 5 seconds The screen shows strange colors or just black and white Q A A Q A A Is the screen disp
17. the DVI Cable to the DVI IN Port on the back of your Monitor DVI IN Connected to a Macintosh e Connect the monitor to the Macintosh computer using the D sub connection cable Note If the monitor and the computer are connected you can turn them on and use them Connecting HDMI P note You can connect digital output devices to your monitor You can enjoy better screen and sound quality Connections Connecting Using a HDMI Cable 1 Input devices such as digital DVD are connected to the HDMI terminal of the monitor using the HDMI cable When all the connections are completed connect the power cords for the monitor and DVD or the device connected to the digital output terminal Select HDMI using the SOURCE button Connecting Using a DVI to HDMI Cable 1 Connect the DVI output terminal of a digital output device to the HDMI terminal of the monitor using a DVI to HDMI cable 2 To listen to sound via an external device refer to the information in its user manual on how to connect the device 3 When all the connections are completed connect the power cords for the monitor and DVD or the device connected to the digital output terminal 4 Selet HDMI using the SOURCE button Connections Note If you just connect using the DVI to HDMI cable without connecting to the sound source you cannot hear sound Connecting USB P note You can use a USB device such as a mouse keyboard Memory Sti
18. the service center of the corresponding product The company is not liable for problems or damages to an external device caused by using an unauthorized cable for the connection Some products do not follow the USB standard and it may cause a malfunction of the device If the device malfunctions even if it is connected to the computer contact the service center of the device computer Connecting the USB Monitor e System Requirements CPU 1 73GHz or Later OS Windows XP Service Pack2 or later However Windows Vista 64bit is not supported RAM 512 MB RAM or more USB 1 1 or higher USB 2 0 recommended USB Monitor l Connect the S UP port of the monitor and the USB port of the computer with the USB cable Connect the terminal WAR of the USB monitor and the USB terminal of the primary monitor using a USB cable Connections Note For more information on the driver installation and usage of the USB monitor refer to Restrictions on the 7 USB Monitor Installing and Using the USB Monitor 1 Engage and fix the USB monitor into the groove of the armrest holder 2 You can adjust the location of the USB monitor Note You can also adjust the length of the armrest holder after adjusting the location of the USB monitor l B a 1 Do not tilt the stand too far backwards when the USB auxiliary monitor is lifted up as shown in the figure This may change the cent
19. the system when using it in a public place The locking device has to be purchased separately The appearance and locking method may differ from the illustration depending on the manufacturer Refer to the manual provided with the Kensington Lock for proper use The locking device has to be purchased separately Note The location of the Kensington Lock may be dif ferent depending on its model Using the Anti Theft Kensington Lock 1 Insert the locking device into the Kensington slot on the Monitor and turn it in the locking direction 2 Connect the Kensington Lock cable 3 Fix the Kensington Lock to a desk or a heavy stationary object GX mc Introduction Ok Headphone output terminal MIC Connect a microphone to the MIC terminal Fix the cables using the holding ring as shown in the figure Note See Connecting Cables for further information regarding cable connections Connections Connecting Cables Rear of Monitor Rear of Computer Macintosh SAMEUMGE r E O Connect the power cord for your monitor to the power port on the back of the monitor Plug the power cord for the monitor into a nearby outlet Use a connection appropriate for your computer Using the D sub Analog connector on the video card e Connect the signal cable to the 15 pin D sub port on the back of your monitor Using the DVI Digital connector on the video card e Connect
20. tion function reduces afterimages on the panel by turning the USB auxiliary monitor on and off automatically for a short time about 0 1 seconds every thirty 30 minutes The configuration at the back of the monitor may vary from product to product Introduction SAMSUNG POWER POWER Connect the power cord for your monitor to the POWER port on the back of the monitor gt HDMI DVI IN RGB IN HDMI Connect the HDMI terminal at the back of your monitor to the HDMI terminal of your digital out put device using a HDMI cable brn Connect the DVI cable to the DVI IN port on the back of your monitor kog IN Connect the RGB IN terminal at the back of your monitor to your computer USB connection termi nal Option Introduction Dup USB upstream port Connect the S UP port of the monitor and the USB port of the computer with the USB cable Opown USB downstream port Connect the DO WN port of the USB monitor and a USB device with the USB cable Note Touse DOWN Downstream Port you have to connect the S UP Upstream Cable to the PC Make sure to use the USB cable supplied with this monitor to connect the monitor s UP port and your computer s USB port Note For the procedures on connecting the 7 USB monitor refer to Connecting the USB Monitor o A 8 Kensington Lock The Kensington Lock is a device used to physi cally fix
21. y indicate that the monitor is out of scan range or that you need to check the signal cable Not Optimum Mode Recommended Mode ey tere U7 Environment The location and the position of the monitor may influence the quality and other features of the monitor If there are any sub woofer speakers near the monitor unplug and relocate the woofer to another room Remove all electronic devices such as radios fans clocks and telephones that are within 3 feet one meter of the monitor Useful Tips A monitor recreates visual signals received from the computer Therefore if there is a problem with the computer or the video card this can cause the monitor to become blank have poor coloring become Troubleshooting noisy and video mode not supported etc In this case first check the source of the problem and then contact the Service Center or your dealer Judging the monitor s working condition If there is no image on the screen or a Not Optimum Mode Recommended Mode 1680 x 1050 60 Hz message comes up disconnect the cable from the computer while the monitor is still powered on If there is a message coming up on the screen or if the screen goes white this means the monitor is in working condition In this case check the computer for trouble Check List Note Before calling for assistance check the information in this section to see if you can remedy any prob lems yourself If you do need assistance please call t
Download Pdf Manuals
Related Search