NEC MultiSync® LCD1770NX
Contents
1. Use a document holder placed close to the screen Position whatever you are looking at most of the time the screen or reference material directly in front of you to minimize turning your head while you are typing Avoid displaying fixed patterns on the monitor for long periods of time to avoid image persistence after image effects Get regular eye checkups Ergonomics To realize the maximum ergonomics benefits we recommend the following Adjust the Brightness until the background raster disappears Do not position the Contrast control to its maximum setting Use the preset Size and Position controls with standard signals Use the preset Colour Setting Use non interlaced signals with a vertical refresh rate between 60 75 Hz Do not use primary colour blue on a dark background as it is difficult to see and may produce eye fatigue to insufficient contrast Cleaning the LCD Panel When the liquid crystal panel is stained with dust or dirt please wipe with soft cloth gently Please do not rub the LCD panel with hard material Please do not apply pressure to the LCD surface Please do not use OA cleaner it will cause deterioration or discolor on the LCD surface Cleaning the Cabinet Unplug the power supply Gently wipe the cabinet with a soft cloth To clean the cabinet dampen the cloth with a neutral detergent and water wipe the cabinet and follow with a dry cloth NOTE Many plastics are used on the surface of the cabi2. MultiSync LCD1770NX User s Manua Index WaN C AUOT oea de re ee oe ane ee d English 1 BD SG IAN UDO I eccetaload cee ne es nee en a tonte caver dant Adi et lt English 1 Canadian Department of Communications Compliance Statement ccccecseeeeeeeeeeeeeeeeeens English 2 Declaration ot COMIORMIY nesrin crest anes oe ea octane pases ees English 2 OPS So RS ce shits ate ea enna Staessen aie ortega de cease te e eed English 3 UT Ee ere ARS ae a ee Ren ea en ee Oo ere English 4 CONTO Siecle cerca Ge arated en kerri AR nee an Re Eclat et tete ne ete de English 8 Recommended USE En Sean cn nee to en a ae English 10 D D CITICAIOMS anes eae renee eer ee een ee ee cee ee ee ere en English 12 FCO SEE English 13 TOUDE SHOO i cantare tule sac edict Sr nn RAS d s s etie ton ltd English 14 TCO U PR A aah Seca hates neste aces eee ete English 15 Manufacturer s Recycling and Energy Information English 16 WARNING TO PREVENT FIRE OR SHOCK HAZARDS DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE ALSO DO NOT USE THIS UNIT S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL AN CAUTION CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET TO FULLY DISENGAGE THE POWER TO THE UNIT PLEASE DISCONNECT THE
3. SIZE e Check to make sure that a supported mode has been selected on the display card or system being used Please consult display card or system manual to change graphics mode No Video e f no video is present on the screen turn the vacation switch off and on again e Make certain the computer is not in a power saving mode touch the keyboard or mouse English 14 TCO 03 TODevelopment Tt bevelopment Congratulations 7 The display you have just purchased carries the TCO 03 Displays O label This means that your display is designed manufactured and tested according to some of the strictest quality and environmental DISPLAYS requirements in the world This makes for a high performance product designed with the user in focus that also minimizes the impact on our natural environment Some of the features of the TCO 03 Display requirements Ergonomics e Good visual ergonomics and image quality in order to improve the working environment for the user and to reduce sight and strain problems Important parameters are luminance contrast resolution reflectance colour rendition and image stability Energy e Energy saving mode after a certain time beneficial both for the user and the environment e Electrical safety Emissions e Electromagnetic fields e Noise emissions Ecology e The product must be prepared for recycling and the manufacturer must have a certified environmental management system such as EM
4. cable to the Macintosh cable adapter Figure B 1 Tighten all screws iS DVI signal cable Macintosh notincluded Figure A 1 Figure A 2 Cable Adapter Figure B 1 not included NOTE Some Macintosh systems do not require a Macintosh cable adapter 3 Place hands on each side of the monitor to tilt the LCD panel 30 degree angle and lift up to the highest position Figure C 1 4 Connect all cables to the appropriate connectors Figure C 1 NOTE If connecting both DVI and D sub cable the DVI cable must be connected along side the rib on the power cord side Figure C 1 5 For successful cable management place the cables in this order into the cable management power cable and DVI cable Figure C 2 30 Tilt Highest Stand Position 4 DVI Cable Top Power Cable Bottom Figure C 1 Figure C 2 English 4 6 Place DVI cable and power cable into the specific hooks indicated in Figure C 3 7 Place the D Sub into the specific hooks indicated in Figure C 4 8 Make sure all cables are resting flat against the stand Figure C 4 Sub Cable Figure C 3 Figure C 4 9 Hold the all cables firmly and place the cable cover onto the stand Figure D 1 To remove the cable cover lift the cover off as shown in Figure D 2 Insert Top First Then Bottom Figure D 1 Figure D 2 10 Connect the power cord to the power outlet F
5. your municipality to dispose of the tube properly e Do not bend power cord e Do not use monitor in high temperatured humid dusty or oily areas e Do not cover vent on monitor Immediately unplug your monitor from the wall outlet and refer servicing to qualified service personnel under the following conditions e When the power supply cord or plug is damaged e If liquid has been spilled or objects have fallen into the monitor e lf the monitor has been exposed to rain or water e lf the monitor has been dropped or the cabinet damaged e lf the monitor does not operate normally by following operating instructions e lf glass is broken handle with care e f monitor or glass is broken do not come in contact with the liquid crystal and handle with care e Allow adequate ventilation around the monitor so that heat can properly dissipate Do not block ventilated openings or place the monitor near a radiator or other heat sources Do not put anything on top of monitor aay The power cable connector is the primary means of detaching the system from the power supply The monitor should be installed close to a power outlet which is easily accessible e Handle with care when transporting Save packaging for transporting e Image Persistence Image persistence is when a residual or ghost image of a previous image remains visible on the screen Unlike CRT monitors LCD monitors image persistence is not permanent but constant im
6. 73 23 EEC EN 60950 1 Council Directive 89 336 EEC EN 55022 EN 61000 3 2 EN 61000 3 3 EN 55024 NEC Display Solutions Ltd 4 13 23 Shibaura Minato Ku Tokyo 108 0023 Japan 150 13406 2 T V Rheinland Product Safety Windows is a registered trademark of Microsoft Corporation NEC is a registered trademark of NEC Corporation ENERGY STAR is a U S registered trademark OmniColor is a registered trademark of NEC Display Solutions Europe GmbH in the countries of EU and Switzerland ErgoDesign is a registered trademark of NEC Display Solutions Ltd in Austria Benelux Denmark France Germany Italy Norway Spain Sweden U K NaViSet is a trademark of NEC Display Solutions Europe GmbH in the countries of EU and Switzerland MultiSync is a registered trademark of NEC Display Solutions Ltd in the countries of U K Italy Austria Netherlands Switzerland Sweden Spain Denmark Germany Norway and Finland All other brands and product names are trademarks or registered trademarks of their respective owners As an ENERGY Star Partner NEC Display Solutions of America Inc has determined that this product meets the Enercy Star guidelines for energy efficiency The ENERGY Star emblem does not represent EPA endorsement of any product or service English 1 Canadian Department of Communications Compliance Statement DOC This Class B digital apparatus mee
7. AS or ISO 14 001 e Restrictions on chlorinated and brominated flame retardants and polymers heavy metals such as cadmium mercury and lead The requirements included in this label have been developed by TCO Development in co operation with scientists experts users as well as manufacturers all over the world Since the end of the 1980s TCO has been involved in influencing the development of IT equipment in a more user friendly direction Our labelling system started with displays in 1992 and is now requested by users and IT manufacturers all over the world For more information please visit www tcodevelopment com English 15 Manufacturer s Recycling and Energy Information NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company s top priorities in trying to minimize the burden placed on the environment We are engaged in developing environmentally friendly products and always strive to help define and comply with the latest independent standards from agencies such as ISO International Organisation for Standardization and TCO Swedish Trades Union Disposing of your old NEC product The aim of recycling is to gain an environmental benefit by means of re use upgrading reconditioning or reclamation of material Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely disposed To ensure the best recycling of our produc
8. POWER CORD FROM THE AC OUTLET DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock Therefore it is dangerous to make any kind of contact with any part inside this unit A This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included Therefore it should be read carefully in order to avoid any problems Caution When operating the MultiSync LCD1770NX with a 220 240V AC power source in Europe use the power cord provided with the monitor In the UK a BS approved power cord with a moulded plug has a Black five Amps fuse installed for use with this equipment If a power cord is not supplied with this equipment please contact your supplier When operating the MultiSync LCD1770NX with a 220 240V AC power source in Australia use the power cord provided with the monitor If a power cord is not supplied with this equipment please contact your supplier For all other cases use a power cord that matches the AC voltage of the power outlet and has been approved by and complies with the safety standard of your particular country Declaration Declaration of the Manufacturer We hereby certify that the colour monitor and marked with MultiSync LCD1770NX L174F is in compliance with Council Directive
9. ages being displayed for a long period of time should be avoided To alleviate image persistence turn off the monitor for as long as the previous image was displayed For example if an image was on the monitor for one hour and a residual image remains the monitor should be turned off for one hour to erase the image NOTE As with all personal display devices NEC DISPLAY SOLUTIONS recommends using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use English 10 CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE SHOULDER AND NECK FATIGUE CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR For optimum performance allow 20 minutes for warm up Adjust the monitor height so that the top of the screen is at or slightly below eye level Your eyes should look slightly downward when viewing the middle of the screen Position your monitor no closer than 40 cm and no further away than 70 cm from your eyes The optimal distance is 50 cm Rest your eyes periodically by focusing on an object at least 20 feet away Blink often Position the monitor at a 90 angle to windows and other light sources to minimize glare and reflections Adjust the monitor tilt so that ceiling lights do not reflect on your screen If reflected light makes it hard for you to see your screen use an anti glare filter Adjust the monitor s brightness and contrast controls to enhance readability
10. electrical and electronic products only applies to the current European Union Member States If you wish to dispose of used electrical and electronic products outside the European Union please contact your local authority so as to comply with the correct disposal method English 16
11. f a previous image remains visible on the screen Unlike CRT monitors LCD monitors image persistence is not permanent but constant images being displayed for a long period of time should be avoided To alleviate image persistence turn off the monitor for as long as the previous image was displayed For example if an image was on the monitor for one hour and a residual image remains the monitor should be turned off for one hour to erase the image NOTE As with all personal display devices NEC DISPLAY SOLUTIONS recommends using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use Image is unstable unfocused or swimming is apparent e Signal cable should be completely attached to the computer e Use the OSM Image Adjust controls to focus and adjust display by increasing or decreasing the fine total When the display mode is changed the OSM Image Adjust settings may need to be re adjusted e Check the monitor and your display card with respect to compatibility and recommended signal timings e If your text is garbled change the video mode to non interlace and use 60Hz refresh rate LED on monitor is not lit no green or amber colour can be seen e Power Switch should be in the ON position and power cord should be connected e Check the Vacation Switch should be in the ON position Display image is not sized properly e Use the OSM Image Adjust controls to increase or decrease the H
12. g the air conditioning costs of the workplace Multiple Frequency Technology Automatically adjusts monitor to the display card s scanning frequency thus displaying the resolution required FullScan Capability Allows you to use the entire screen area in most resolutions significantly expanding image size VESA Standard Mounting Interface Allows users to connect their MultiSync monitor to any VESA standard third party mounting arm or bracket Allows for the monitor to be mounted on a wall or an arm using any third party compliant device English 13 Troubleshooting No picture e The signal cable should be completely connected to the display card computer e The display card should be completely seated in its slot e Check the Vacation Switch should be in the ON position e Front Power Switch and computer power switch should be in the ON position e Check to make sure that a supported mode has been selected on the display card or system being used Please consult display card or system manual to change graphics mode e Check the monitor and your display card with respect to compatibility and recommended settings e Check the signal cable connector for bent or pushed in pins Power Button does not respond e Unplug the power cord of the monitor from the AC outlet to turn off and reset the monitor e Check the Vacation Switch on the back side of the monitor Image Persistence e Image persistence is when a residual or ghost image o
13. ght of the monitor Thickness of Bracket Arm 2 0 3 2mm 4 Screws 4M Max Depth 8 5mm TA rates 4 100mm A Weight of LCD assembly 4 3kg MAX Figure F 1 English 7 Controls OSM On Screen Manager control buttons on the front of the monitor function as follows To access OSM menu press any of the control buttons MENU EXIT Left Right Down Up To change signal input press the SELECT button NOTE OSM must be closed in order to change signal input x MENU EXIT j Button Menu MENU EXIT Exits the OSM controls Exits to the OSM main menu Left Right Moves the highlighted area left right to select control menus Moves the bar left right to increase or decrease the adjustment Down Up Moves the highlighted area down up to select one of the controls SELECT Active Auto Adjust function Enter the OSM sub menu RESET Resets the highlighted control menu to the factory setting NOTE When RESET is pressed in the main and sub menu a warning window will appear allowing you to cancel the RESET function by pressing the MENU EXIT button X Brightness Contrast Controls BRIGHTNESS Adjusts the overall image and background screen brightness CONTRAST Adjusts the image brightness in relation to the background AUTO CONTRAST Analog input only Adjusts the image displayed to optimal settings Auto Adjust Analog input only Automatica
14. igure E 1 NOTE Please refer to Caution section of this manual for proper selection of AC power cord 11 The vacation switch on the back side of the monitor must be turned on Figure E 1 Turn on the monitor with the front power button and the computer NOTE The vacation switch is a true on off switch If this switch is on the OFF position the monitor cannot be turned on using the front button DO NOT switch on off repeatedly 12 No Touch Auto Adjust automatically adjusts the monitor to optimal settings upon initial setup for most timings For further adjustments use the following OSM controls e Auto Adjust Contrast Analog input only e Auto Adjust Analog input only Refer to the Controls section of this User s Manual for a full description of these OSM controls NOTE If you have any problems please refer to the Troubleshooting section of this User s Manual OFF Position i ON Position Vacation Switch Power Button Figure E 1 English 5 Raise and Lower Monitor Screen The monitor may be raised or lowered To raise or lower screen place hands on each side of the monitor and lift or lower to the desired height Figure RL 1 Handle with care when raising or lowering the monitor screen NOTE Figure RL 1 Tilt and Swivel Grasp both sides of the monitor screen with your hands and adjust the tilt and swivel as desired Figure TS 1 NOTE Handle with care when tilting and swivelling the mo
15. image settings upon initial power on Colour Control System allows you to change between six colour settings on your display to match your personal preference Redesigned OSM controls allow you to quickly and easily adjust all elements of your screen image NaViSet software offers an expanded and intuitive graphical interface allowing you to more easily adjust OSM display settings via mouse and keyboard Height adjustable stand with tilt swivel and cable management adds flexibility to your viewing preferences The flat screen s crisp bright images and crystal clear text deliver a comfortable viewing experience ErgoDesign Features Enhance human ergonomics to improve the working environment protect the health of the user and save money Examples include OSM controls for quick and easy image adjustments tilt base for preferred angle of vision small footprint and compliance with MPRII and TCO guidelines for lower emissions Plug and Play The Microsoft solution with the Windows operating system facilitates setup and installation by allowing the monitor to send its capabilities such as screen size and resolutions supported directly to your computer automatically optimizing display performance IPM Intelligent Power Manager System Provides innovative power saving methods that allow the monitor to shift to a lower power consumption level when on but not in use saving two thirds of your monitor energy costs reducing emissions and lowerin
16. lly adjusts the Image Position H Size and Fine settings D Image Controls Analog input only LEFT RIGHT Controls Horizontal Image Position within the display area of the LCD DOWN UP Controls Vertical Image Position within the display area of the LCD H SIZE Adjusts the horizontal size by increasing or decreasing this setting FINE Improves focus clarity and image stability by increasing or decreasing this setting English 8 HEHU Colour Control System Colour Control System Six colour presets select the desired colour setting SRGB and NATIVE colour presets are standard and cannot be changed R G B Increases or decreases Red Green or Blue colour depending upon which is selected The change in colour will appear on screen and the direction increase or decrease will be shown by the bars NATIVE Original colour presented by the LCD panel that is unadjustable sRGB sRGB mode dramatically improves the colour fidelity in the desktop environment by a single standard RGB colour space With this colour supported environment the operator could easily and confidently communicate colour without further colour management overhead in the most common situations Tools OFF TIMER Monitor will automatically power down when the end user has selected a predetermined amount of time HOT KEY You can adjust the brightness and contrast directly When this function is set to ON you can adjust the brightness with left or righ
17. net DO NOT clean with benzene thinner alkaline detergent alcoholic system detergent glass cleaner wax polish cleaner soap powder or insecticide Do not touch rubber or vinyl to the cabinet for a long time These types of fluids and fabrics can cause the paint to deteriorate crack or peel English 11 Specifications Monitor Specifications LCD Module Diagonal Viewable Image Size Native Resolution Pixel Count Input Signal Video Sync Display Colours Synchronization Range Horizontal Vertical Viewing Angle Left Right Up Down Resolutions Supported Active Display Area Horizontal Vertical Power Supply Power Consumption without optional Sound Bar Current Rating Dimensions Weight Environmental Considerations Operating Temperature Humidity Feet Storage Temperature Humidity Feet MultiSync LCD1770NX Monitor 43 2 cm 17 0 inches 43 2 cm 17 0 inches 1280 x 1024 ANALOG 0 7 Vp p 75 Ohms Separate sync TTL Level Horizontal sync Positive Negative Vertical sync Positive Negative 16 777 216 31 5 kHz to 81 0 kHz Analog 31 5 kHz to 69 0 kHz Digital 56 0 Hz to 75 0 Hz 80 80 CR gt 10 80 80 CR gt 10 720 x 400 VGA Text 640 x 480 at 60 Hz to 75 Hz 800 x 600 at 56 Hz to 75 Hz 832 x 624 at 75 Hz 1024 x 768 at 60 Hz to 75 Hz 1152 x 870 at 75 Hz 1280 x 1024 at 60 Hz to 75 Hz Analog 1280 x 1024 at 60 Hz Digital 337 9 mm 13 3 inche
18. nitor screen Figure TS 1 Remove Monitor Stand for Mounting To prepare the monitor for alternate mounting purposes 1 Place hands on each side of the monitor and lift up to the highest position Remove the cable cover Figure S 1 2 Disconnect all cables 3 Place monitor face down on a non abrasive surface Figure S 2 4 Remove the 2 screws connecting the stand to the monitor Figure S 2 ZAHA Figure S 2 Figure S 1 English 6 Lift up the stand to unlatch the upper hooks and remove the stand Figure S 3 Remove the 2 screws on the top of the monitor Figure S 4 The monitor is now ready for mounting in an alternate manner Connect the cables to the back of the monitor 8 Reverse this process to re attach stand Use only VESA compatible alternative mounting method Handle with care when removing stand NOTE N AL NN Figure S 3 Figure S 4 Flexible Arm Installation This LCD monitor is designed for use with a flexible arm To mount the monitor to a flexible arm 1 Follow the instructions on how Remove Monitor Stand for Mounting to remove the stand 2 Using the 4 screws from the stand removal and attach the arm to the monitor Figure F 1 NOTE The LCD monitor should only be used with an approved arm e g GS mark To meet the safety requirements the monitor must be mounted to an arm which guaranties the necessary stability under consideration of the wei
19. s 270 3 mm 10 6 inches AC 100 240V 50 60Hz 36W typ 0 7 0 35A Notes Active matrix thin film transistor TFT liquid crystal display LCD 0 264 mm dot pitch 250 cd m white luminance 600 1 contrast ratio typical Digital Input DVI Depends on display card used Automatically Automatically Automatically Some systems may not support all modes listed Recommended resolution is 60 Hz for optimal display performance 367 0 mm W x 362 5 472 5 mm H x 198 0 mm D 14 4 inches W x 14 3 18 6 inches H x 7 8 inches D 6 1 kg 13 4 Ibs 5 C to 35 C 41 F to 95 F 30 to 80 O to 15 000 Feet 10 C to 60 C 14 F to 140 F 10 to 85 O to 40 000 Feet 1 Interpolated Resolutions When resolutions are shown that are lower than the pixel count of the LCD module text may appear different This is normal and necessary for all current flat panel technologies when displaying non native resolutions full screen In flat panel technologies each dot on the screen is actually one pixel so to expand resolutions to full screen an interpolation of the resolution must be done NOTE Technical specifications are subject to change without notice English 12 Features Thin frame design creates more desktop space for you to work and play while the flat screen s crisp bright images and crystal clear text deliver a comfortable viewing experience No Touch Auto Adjust automatically adjusts your optimal
20. s 1280 x 1024 If ON is selected a message will appear on the screen after 30 seconds notifying you that the resolution is not at 1280 x 1024 Information The Information menu indicates the current input display resolution horizontal and vertical frequency and polarity settings of the monitor The model and serial numbers of your monitor are also indicated English 9 Recommended use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE MULTISYNC LCD COLOUR MONITOR e DO NOT OPEN THE MONITOR There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks Refer all servicing to qualified service personnel e Do not spill any liquids into the cabinet or use your monitor near water e Do not insert objects of any kind into the cabinet slots as they may touch dangerous voltage points which can be harmful or fatal or may cause electric shock fire or equipment failure e Do not place any heavy objects on the power cord Damage to the cord may cause shock or fire e Do not place this product on a sloping or unstable cart stand or table as the monitor may fall causing serious damage to the monitor e Do not place any objects onto the monitor and do not use the monitor outdoors e The inside of the fluorescent tube located within the LCD monitor contains mercury Please follow the bylaws or rules of
21. sh 2 Contents Your new NEC MultiSync LCD monitor box should contain the following e MultiSync LCD1770NX monitor with tilt swivel pivot height adjust stand e Power Cord e Video Signal Cable e User s Manual e Cable Cover e CD ROM includes complete User s Manual in PDF format To see the User s Manual Acrobat Reader 4 0 must be installed on your PC Power Cord MultiSync Pa Manua ZIvatelsk P ru ediene than a db O6n Vie Xor UCh OJ oe del usuario A NUE Utilis ateur Gi PURE utente ebr P ruiker Shandlejoy Odrec Znj ng k u PyKoBagey Vikowinkg Cable Cover no Kullan c Klavwuzy VIb30Ba Teng User s Manual 15 pin mini D SUB male to CD ROM 15 pin mini D SUB male Remember to save your original box and packing material to transport or ship the monitor English 3 Quick Start To attach the MultiSync LCD monitor to your system follow these instructions 1 Turn off the power to your computer 2 For the PC or MAC with DVI digital output Connect the DVI signal cable not included to the connector of the display card in your system Figure A 1 Tighten all screws For the PC with Analog output Connect the 15 pin mini D SUB signal cable to the connector of the display card in your system Figure A 2 Tighten all screws For the MAC Connect the Macintosh cable adapter to the computer then attach the 15 pin mini D SUB signal
22. t control and contrast with up or down control while the OSM menu is off DDC CI This function allows the DDC CI function ON or OFF FACTORY PRESET Selecting Factory Preset allows you to reset all OSM control settings back to the factory settings The RESET button will need to be held down for several seconds to take effect Individual settings can be reset by highlighting the control to be reset and pressing the RESET button Menu Tools LANGUAGE OSM control menus are available in eight languages OSM LEFT RIGHT You can choose where you would like the OSM control image to appear horizontally on your screen OSM DOWN UP You can choose where you would like the OSM control image to appear vertically on your screen OSM Turn Off The OSM control menu will stay on as long as it is in use In the OSM Turn Off submenu you can select how long the monitor waits after the last touch of a button to shut off the OSM control menu OSM Lock Out This control completely locks out access to all OSM control functions without Brightness and Contrast When attempting to activate OSM controls while in the Lock Out mode a screen will appear indicating the OSM controls are locked out To activate the OSM Lock Out function press SELECT then right control button and hold down simultaneously To deactivate the OSM Lock Out press SELECT then left control button and hold down simultaneously while in the OSM menu RESOLUTION NOTIFIER This optimal resolution i
23. ts NEC DISPLAY SOLUTIONS offers a variety of recycling procedures and gives advice on how to handle the product in an environmentally sensitive way once it has reached the end of its life All required information concerning the disposal of the product and country specific information on recycling facilities can be found on our following websites http www nec display solutions com greencompany in Europe http www nec display com in Japan or http www necdisplay com in USA Energy Saving This monitor features an advanced energy saving capability When a VESA Display Power Management Signalling DPMS Standard signal is sent to the monitor the Energy Saving mode is activated The monitor enters a single Energy Saving mode Normal Operation Approx 36W Energy Saving Mode Less than 2W Off Mode Less than 1W WEEE Mark European Directive 2002 96 EC Within the European Union EU wide legislation as implemented in each Member State requires that waste electrical and electronic products carrying the mark left must be disposed of separately from normal household waste This includes monitors and electrical accessories such as signal cables or power cords When you need to dispose of your NEC display products please follow the guidance of your local authority or ask the shop where you purchased the product or if applicable follow any agreements made between yourself and NEC Outside the European Union The mark on
24. ts all requirements of the Canadian Interference Causing Equipment Regulations C UL Bears the C UL Mark and is in compliance with Canadian Safety Regulations according to CAN CSA C22 2 No 60950 1 FCC Information 1 Use the attached specified cables with the MultiSync LCD1770NX L174F colour monitor so as not to interfere with radio and television reception 1 The power supply cord you use must have been approved by and comply with the safety standards of U S A and meet the following condition Power supply cord Non shield type 3 conductor Length 2 0m Plug shape ge a U S A 2 Please use the supplied shielded video signal cable Use of other cables and adapters may cause interference with radio and television reception This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to tr
25. y to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult your dealer or an experienced radio TV technician for help If necessary the user should contact the dealer or an experienced radio television technician for additional suggestions The user may find the following booklet prepared by the Federal Communications Commission helpful How to Identify and Resolve Radio TV Interference Problems This booklet is available from the U S Government Printing Office Washington D C 20402 Stock No 004 000 00345 4 Declaration of Conformity This device complies with Part 15 of FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation U S Responsible Party NEC Display Solutions of America Inc Address 500 Park Blvd Suite 1100 Itasca Illinois 60143 Tel No 630 467 3000 Type of Product Display Monitor Equipment Classification Class B Peripheral Model MultiSync LCD1770NX L174F FC We hereby declare that the equipment specified above conforms i to the technical standards as specified in the FCC Rules Engli
Download Pdf Manuals
Related Search