LG WD-1274FB
Contents
1. Close supervision is necessary if this appliance is used by or near children Do not allow children to play on with or inside this or any other appliance Do not leave the washer door open An open door could entice children to hang on the door or crawl inside the washer e Never reach into washer while it is moving Wait until the drum has completely stopped The laundry process can reduce the flame retardant of fabrics Do not wash or dry articles that have been cleaned in washed in soaked in or spotted with combustible or explosive substances such as wax oil paint gasoline degreasers dry cleaning solvents kerosene etc which may ignite or explode To avoid such a result carefully follow the garment manufacturer s wash and care instructions Do not slam the washer door closed or try to force the door open when locked This could result in damage to the washer To minimize the possibility of electric shock unplug this appliance from the power supply or disconnect the washer at the household distribution panel by removing the fuse or switching off the circuit breaker before attempting any maintenance or cleaning Never attempt to operate this appliance if it is damaged malfunctioning partially disassembled or has missing or broken parts including a damaged cord or plug SAVE THESE INSTRUCTIONS GROUNDING INSTRUCTIONS This appliance must be grounded In the event of malfunction or brea2. Solution Washer does not start Washer won t spin Door does not open Electrical power cord may not be plugged in or connection may be loose e House fuse blown circuit breaker tripped or a power outage has occurred Water supply tap is not turned on Check that the door is firmly shut Make sure plug fits tightly in wall outlet Reset circuit breaker or replace fuse Do not increase fuse capacity If problem is a circuit overload have it corrected by a qualified electrician Turn on water supply tap Close the door and press the Start Pause button After pressing the Start Pause button it may take a few moments before the clothes washer begins to spin The door must lock before spin can be achieved Once started the door can not be opened for safety reasons Wait one or two minutes before opening the door to give the electric locking mechanism time to release Wash cycle time delayed The washing time may vary by the amount of laundry water pressure water temperature and other using conditions If the imbalance is detected or if the suds removing program works the wash time shall be increased 51 T EEE el guide Symptom Possible Cause Solution Water supply is not adequate in area Water supply taps are not completely open Water inlet hose are kinked The filter of the inlet hose clogged Drain hose is kinked or clogged The dra
3. Hand Wash Pump Start Pause O 1 Start This Start Pause button is used to start wash cycle or pause the cycles 2 Pause If temporary stop of wash cycle is needed press the Start Pause button After the pause button is pressed the power is turned off automatically 4 minutes later Power Oe 1 Power Press the Power button to turn power on and off To cancel the Time Delay function it can also be used 2 Initial Program When the Power button is pressed the washer is ready for Coloureds program And the other initial conditions as follows So if you want to advance into the washing cycle without selecting the program just press the Start Pause button and then the washer will proceed Initial program Coloureds Program Main wash Normal Rinse 800 rpm 40 C 45 le to use washer Display 1 Special function display When child lock is selected the TL is displayed When time delay is selected it shows the remaining times to finish the selected program 2 Self diagnose display If the washer has a trouble the trouble type is displayed PE Sensing water pressure error FE Problem of overfilling water dE Door is not closed Over load in moter Over load in moter Water inlet trouble Drainage trouble Imbalance trouble E Water temperature trouble If this error letters are displayed please refer to the tro
4. La WD 1374 6 F H B WD 1274 6 F H B WD 1174 6 F H B WD 1074 6 F H B WD 8074F H B Waschmaschine BEDIENUNGSANLEITUNG Vielen Dank f r den Kauf der vollautomatischen LG Waschmaschine Bitte lesen Sie sich diese Bedienungsanleitung sorgfaltig durch da sie die Anweisungen zur sicheren Installation und Bedienung Wartung und Pflege enthalt Die Bedienungsanleitung zum spateren Gebrauch aufbewahren Notieren Sie bitte die Modell und Seriennummer Ihrer Waschmaschine Washing Machine OWNER S MANUAL Thank you for buying a LG Fully Automatic Washing machine Please read your owner s manual carefully it provides instructions on safe installation use and maintenance Retain it for future reference Record the model and serial numbers of your washing machine Led Feature s d n Jumbo drum LG s jumbo drum can wash about 40 more load than conventional washing machines A bigger drum improves the wash performance n More economical by Intelligent Wash System Intelligent Wash System detects the amount of load and water temperature and then determines the optimum water level and washing time to minimize energy and water consumption n Child Lock The Child Lock system has been used to prevent children from pressing any button to change the program during operation n Low noise speed control system By sensing the amount of load and balance it evenly distributes load to minimize the spinning noise level
5. n Installation place requirement Level floor Allowable slope under entire washer is 1 Power outlet Must be within 1 5 meters of either side of location of washer Do not overload the outlet with more than one appliance Additional Clearance For wall door and floor modeling is required 10cm rear 2cm right amp left side Drain Hose Do not place or store laundry products on top of washer at any times They can damage the finish or controls 600 n BS Plug Safety Details For U K User IMPORTANT THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE GREEN AND YELLOW EARTH BLUE NEUTRAL BROWN LIVE This appliance must be earthed Green and Yellow Earth Brown Live Blue Neutral Fuse Cord grip As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol or coloured Green or Green and Yellow The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or coloured Black The wire which is coloured Brown must be connected to the terminal which is marked with the lett
6. 88 800 Rinse 600 50 400 40 Eco No Spin 30 Rapid lo Pre Wash Rinse Hold Cold Door Lock Pre Wash Wool Hand Wash Wash Delicate oO R Rinse Spin en Synthetic No Spin pin M Rinse Hold Coloureds 0 0 Pump Start Pause Whiles 0 Option Spin Temp Time Delay Rapid Start Pause P A A S A6 i gt N P y m2 1 Button Option 2 Button Spin 3 Button Temp Option Bio By pressing the Option Rinse button the Option function Eco can be selected Pre Wash Bio Option Rinset AN Eco Pre Wash 1 Bio If you want to elimenate protein stains milk blood chocolate you may select Bio function by pressing the option button You can select Bio function when temperature is higher than 60 C in Whites Coloureds and Synthetic 2 Rinse If you wish to rinse more Rinse function will remove any trace of detergents By selecting Rinset function the Rinse Time and the Rinse water are increased 4 Child Lock 5 Button Time Delay 6 Button Rapid 7 Button Start Pause 8 Dial Program 9 Button Power 3 Eco By selecting Eco function the water temperature is reduced and washing time is lengthened So you can economize in your consumption of energy You can select Eco function when temperature is higher than 60 C in Whites Coloureds and Synthetic 4
7. n Auto Restart If the washing machine is turned off by a power failure it will restart automatically from the position it stopped at adjusting accordingly Keje tents bna niy DD rrr brKbn 30 Specification a 2a 31 Installation 2 40 rates heiter 32 Care before washing EiiE kk keke keke 37 Adding detergent lllllllll keka keka ka k 38 al la LD N N DD S 39 How to use washer EEE kk kk kk kk kk k KAKA K 40 Maintenance sr a EA 47 Troubleshooting guide L nennen nnennnnnnnnnnnnnnen nen 50 29 Kijaminss READ ALL INSTRUCTIONS BEFORE USE A WARNING For your safety the information in this manual must be followed to minimize the risk of fire or explosion electric shock or to prevent property damage personal injury or loss of life IMPORTANT SAFETY INSTRUCTIONS WARNING To reduce the risk of fire electric shock or injury to persons when using the washer follow basic precautions including the following Do not install or store the washer where it will be exposed to the weather Do not tamper with controls Do not repair or replace any part of the washer or attempt any servicing unless specifically recommended in the user maintenance instructions or published user repair instructions that you understand and have the skills to carry out Keep the area underneath and around your appliances free of combustible materials such as lint paper rags chemicals etc
8. pump Heavy wash loads may produce a thumping sound This is usually normal e Have all the transit bolts and packing been removed Are all the feet resting firmly on the ground Stop washer and check drum and drain filter If noise continues after washer is restarted call your authorized service If sound continues washer is probably out of balance Stop and redistribute wash load If not removed during installation See Installation for removing transit bolts Wash load unevenly distributed in drum Stop washer and rearrange wash load Water leaks Oversudsing Water does not enter washer or it enters slowly Water in the washer does not drain or drains slowly 50 Fill hoses or drain hose is loose at tap or washer House drain pipes are clogged e Water supply is not adequate in area e Water supply tap is not completely open Water inlet hose are kinked The filter of the inlet hose clogged Drain hose is kinked or clogged The drain filter is clogged Check and tighten hose connections Unclog drain pipe Contact plumber if necessary Too much detergent or unsuitable detergent The formation of foam can cause water leaks Check another tap in the house Fully open tap Straighten hose Check the filter of the inlet hose Clean and straighten the drain hose Clean the drain filter T ioublesiostins guide Symptom Possible Cause
9. 8074F H B No Spin 400 600 800 1 000 WD 1074 6 F H B No Spin 400 600 800 1 1 OO WD 1 174 6 F H B No Spin 400 600 800 1000 1 200 WD 1274 6 F H B No Spin 400 600 800 1 100 1300 WD 1374 6 F H B n Water consumption 75 9 10 7 g kg n Permissible water pressure 0 3 10kgf cm 30 1000kPa The appearance and specifications may be varied without notice to raise the units quality n Accessories Inlet hose 1EA Option Hot Cold 2EA Spanner 31 EE HSIISESNA Install or store where it will not be exposed to temperatures below freezing or exposed to the weather Properly ground washer to conform with all governing codes and ordinances The base opening must not be obstructed by carpeting when the washing machine is installed on a carpeted floor n Transit bolts The appliance is fitted with transit bolts to prevent internal damage during transport n Removing transit bolts 1 To prevent internal damage during 3 Take out the 4 bolts along with the rubber transport the special 4 bolts are locked bungs by slightly twisting the bung Keep Before operating the washer remove the 4 bolts and the spanner for future use the bolts along with the rubber bungs Whenever the appliance is transported the If they are not removed it may cause heavy transit bolts must be refitted vibration noise and malfunction 2 Unscrew the 4 bolts with 4 Close the holes with the caps supplied the spanner supplied 32 1 li
10. Inlet hose which has red connector is for the hot water tap If the washer has two valves the energy is saved by using hot valve 1 en n Installation of drain hose ca 100 cm ca 145 cm soy lt gt mm cu Ra K ca 105 cm max 100 cm min 60 cm ca 145 cm ca 105 cm The drain hose should not be placed higher than 100 cm above the floor Proper securing the drain hose will protect the floor from damage due to water leakage When the drain hose is too long please don t fill into the washer This will cause abnormal noise max 100 cm When installing the drain hose sink secure it tightly with a string Proper securing the drain hose will protect the floor from damage due to water leakage Laundry tub max 100cm T min 60cm When installing the drain hose sink secure it tightly with a string Proper securing the drain hose will protect the floor from damage due to water leakage 35 Dee n Level adjustment Adjustable feet jJ qene BE Lower D gt Adjustable feet 36 1 Adjustable the washing machine properly prevents excessive noise and vibration Install the appliance on a solid and level floor surface preferably in a corner of the room If the floor is uneven adjust the adjustable feet as required do not insert pieces of woo
11. Pre Wash If the laundry is heavily soiled Pre Wash course is effective Pre Wash is available in Whites Coloureds and Synthetic If lamp turns on that function has been selected 41 HGy to use washer Spin 1000 1100 800 800 800 600 600 600 400 400 400 No Spin No Spin No Spin Rinse Hold Rinse Hold Rinse Hold Spin Spin Spin l WD 8074F H B WD 1074 6 F HIB WD 117406 F HB 1200 1300 1000 1100 800 800 600 600 400 400 No Spin No Spin Rinse Hold Rinse Hold Spin Spin WD 1274 8 F H B WD 1874 8 F H B By pressing the Spin button the spin speed can be chosen 1 Spin selection Spin speed is available according to the program as follows WD 8074F H B Whites Coloureds Synthetic 800u Rinse Holdu No Spinu 400U 600 Delicate Wool Hand Wash 400u 600U 800U Rinse Holdu No Spin 42 WD 1074 6 F H B Whites Coloureds Synthetic 800U 1000U Rinse Holdu No Spinu 400u 600 Delicate 400u 600U 800U Rinse Holdu No Spin Wool Hand Wash 400u 600U 800U 1000U Rinse Holdu No Spin WD 1174 6 F H B Whites Coloureds Synthetic 800u 1100U Rinse Holdu No Spinu 400U 600 Delicate 400u 600U 800U Rinse Holdu No Spin Wool Hand Wash 400u 600U 800U 1100U Rinse Holdu No Spin WD 1274 6 F H B Whites Coloureds 800u 1000U 1200U Rinse Holdu No Spinu 400u 600 Synthetic 800u 1000U Rinse Holdu No Spinu 400u 600 Delicate 400u 600U 800U Rinse Holdu No Spin
12. Wool Hand Wash 400u 600U 800U 1000U Rinse Holdu No Spin Li to use washer WD 1374 6 F H B Whites Coloureds 800U 1100U 1300U Rinse Holdu No Spinu 400u 600 Synthetic 800U 1100U Rinse Holdu No Spinu 400u 600 Delicate 400u 600U 800U Rinse Holdu No Spin Wool Hand Wash 400u 600U 800U 1100U Rinse Holdu No Spin 2 No spin If no spin is selected the washer stops after draining water If lamp turns on that function has been selected 3 Rinse Hold If you desire to leave fabrics in the machine without spinning after rinse to prevent them from getting wrinkled you may select rinse hold by pressing the spin button If you want to drain and spin when Rinse Hold function is proceed press the Start Pause button to cancel the Rinse Hold function and select spin speed or program press the Start Pause button again to start program e If you want to drain only select the no spin or pump program If lamp turns on that function has been selected Water Temp 95 C By pressing the Temp 2 button the water 40 temperature can be v selected Cold Temp 30 C 40 C 50 C 60 C 95 C 1 Water Temperature Water temperature can be selected as below according to the program Whites 95 C U 40 C U 50 CU 60 C Coloureds amp Synthetic 40 C u 50 C U 60 C u Cold u 30 C Delicate amp Wool 30 C u 40 C u Cold Hand Wash Cold U 30 C u 40 C Selected temperat
13. an out of balance load Add one or two similar items Check all the pockets to make sure that they are empty Things such as nails hair clip matches pens coins and keys can damage both your washer and your clothes Close zippers hook and strings to make sure that these items don t snag on other clothes Pre treat dirt and stains by brushing a little detergent dissolved in water onto stains like collars and cuffs to help shift dirt 37 A i detergent n Adding detergent and fabric softener 1 The Dispenser Drawer Detergent for Fabric Detergent for main wash softener pre wash wm 8 LLY e Main wash only U LL e Pre Wash Main Washu L ll 2 Adding Fabric Softener eyo SH Do not exceed the maximum fill line Overfilling can cause early dispensing of the fabric softener which could stain clothes Do not leave the fabric softener in the detergent drawer for more than 2 days Fabric softener could harden Softener will automatically be added during last rinse cycle Do not open the drawer when water is supplied Solvents benzene etc are not allowable Do not pour fabric softener directly on the clothes 38 3 Detergent dosage The detergent should be used according to the instruction of the detergent manufacture If too much detergent is used more than the recommended amount too many suds can occur and this will decrease the washing result
14. arranty for this apparatus During the 12 month warranty period we will repair your apparatus at no cost to you or make available spare parts to your dealer free if this apparatus fails due to manufacturing or material defects Further claims are excluded We are not liable for damages due to acts of providence or damages occurring during transport The buyer assumes shipping and packaging costs Your warranty conditions on the rear also apply Type of apparatus Name of buyer Purchase date Serial number Dealer s stamp and signature 53 54 LG Electronics Inc P No 3828ER3010G
15. awer and run a rinse cycle without laundry n The washing drum e If you live in a hard water area limescale continuously builds up in places where it cannot be seen and it is not easily removed Over time the build up of scale clogs appliances and if it is not kept in check these will eventually have to be replaced Although the washing drum is made of Stainless steel specks of rust can be caused by small metal articles paper clips safety pins which have been left in the drum The washing drum should be cleaned from time to time If you use descaling agents dyes or bleaches make sure they are suitable for washing machine use Descaler could contain components that can attack part of your washing machine Remove the spots with a stainless steel cleaning agent Never use steel wool 48 ij e HERARc n Cleaning your washer 1 Exterior Proper care of your washer can extend its life The outside of the machine can be cleaned with warm water and a neutral non abrasive household detergent Immediately wipe off any spills Wipe with damp cloth Try not to hit surface with sharp objects IMPORTANT Do not use methylated spirit diluents or similar products 2 Interior Dry around the washer door opening flexible gasket and door glass These areas should always be clean to ensure a water tight seal Run washer through a complete cycle using hot water Repeat process if necessary Gi Remove hard
16. ctive Pre Wash is available in Coloureds Whites and Synthetic Program Eco By selecting Eco function the water temperature is reduced and washing time is lengthened So you can economize in your consumption of energy Rinse If you wish to rinse more the Rinse function will remove any trace of detergents Bio If you want to elimenate protein stains milk blood chocolate you may select Bio function by pressing the option button You can select Bio function and Eco function when temperature is higher than 60 C in Whites Coloureds and Synthetic 39 le to use washer Pre Wash Bio Rinse Eco Wool Hand Wash Delicate 2 p S gt Rinse Spin Synthetic 9 M Spin Coloureds 0 N Pre Wash Rinse Hold Cold Door Lock Start Pause Whites ol Option Spin Temp Time Delay Rapid Start Pause N 3 4 1 For use in the initial programme Coloureds Press the Power button to start Press the Start Pause button Initial condition Wash Only main wash Rinse 3 times Spin 800 rpm Water temperature 40 C Program Coloureds 40 2 Manual Selecting Press the Power button to start Select the conditions which you want to use by pressing each button For selecting the each conditions please refer to the page41 page45 Press the Start Pause button Li to use washer 1200 95 C Bio 1000 60 18
17. d filled in and signed by the seller The serial number of the product must agree with the number entered onto the warranty card During the warranty period we will correct any defects at no cost to you if it can be proven that these are attributed to manufacturing or material defects Damages due to incorrect handling non compliance with instructions for use and normal wear are not covered by this warranty Also the warranty does not cover wear parts or easily broken parts for example viewing glass light bulbs The buyer is responsible for any damages during transport as well as shipping and packaging costs 4 We decide whether to make repairs exchange or replace parts Exchanged or replaced parts are our property The original warranty period is not prolonged if a refrigerator is repaired or certain parts are replaced The warranty is nullified if any person intervenes in the apparatus that are not authorised by LG Electronics if the apparatus is used for commercial purposes Always keep the original packaging so that if the apparatus requires servicing it can be transported without damaging it If a repair is covered by this warranty always contact your dealer or an authorised service centre Further claims are excluded If parts of these provisions are invalid they apply in the sense of the wording The validity of the other provisions is not effected Warranty Certificate For offer a 12 month w
18. d etc under the feet Make sure that all four feet are stable and resting on the floor and then check that the appliance is perfectly level use a spirit level Diagonal Check When pushing down the edges of the washing machine top plate diagonally the machine should not move up and down at all Please check both of two directions If machine rocks when pushing the machine top plate diagonally adjust the feet again ch before washing n Caring before washing 1 Care Labels Look for a care label on your clothes This will tell you about the fabric content of your garment and how it should be washed 2 Sorting To get the best results Sort clothes into loads that can be washed with the same wash cycle Water temperature and spin speed and different fabrics need to be washed in different ways Always sort dark colors from pale colors and whites Wash separately as dye and lint transfer can occur causing discoloration of white etc If possible do not wash heavily soiled items with lightly soiled one Soil Heavy Normal Light Separate clothes according to amount of soil Color White Lights Darks Separate white fabrics from colored fabrics Lint Lint producers Collectors Wash lint producers and lint collectors separately 3 Caring before loading n Combine large and small items in a load Load large items first Large items should not be more than half the total wash load Do not wash single items This may cause
19. e brush n The drain pump filter The drain filter collects threads and small objects left in the laundry Check regularly that the filter is clean to ensure smooth running of your machine A CAUTION First drain it using the drain hose and then open the pump filter to remove whatever may have stopped it up Be careful when draining if the water is hot 1 Open the lower cover 2 Unplug the drain plug 3 Take out any foreign material cap T by using allowing the water to flow out At from the pump filter After coin Turn the drain this time use a vessel to prevent cleaning turn the pump filter plug to pull out water flowing on to the floor If the clockwise and insert the drain the hose water does not flow any more turn plug to the original place the pump filter open to the left close the lower cover cap 47 Mai n Dispenser drawer After a while detergents and fabric softeners leave a deposit in the drawer It should be cleaned from time to time with a jet of running water If necessary it can be removed completely from the machine by pressing the catch downward and by pulling it out To facilitate cleaning the upper part of the fabric softener compartment can be removed n The drawer recess Detergent can also accumulate inside the recess which should be cleaned occasionally with an old toothbrush e Once you have finished cleaning replace the dr
20. er L or coloured Red Ifa 13 amp BS 1363 plug is used fit a 13 amp BS 1362 fuse 33 EE ESEN n Electrical connection 1 Do not use an extension cord or double adapter 2 If the supply cord is damaged it must be replaced by the manufacturer or its service agents or similarly qualified person in order to avoid a hazard 3 Always unplug the machine and turn off the water supply after use 4 Connect the machine to an earthed socket in accordance with current wiring regulations 5 The appliance must be positioned so that the plug is easily accessible n Washing Machine is to be connected to the water mains using new hose sets and that old hose sets should not be used n Connecting water supply hose A Hose connector Rubber seal pr Cold N U water LD 34 Water supply pressure must be between 30kPa and 1000kPa 0 3 10kgf cm Don t strip or crossthread when connecting Inlet hose to the valve gt If the water supply pressure is more than 1000kPa a decompression device should be installed Two rubber seals are supplied with the water inlet hoses these are in order to prevent water leaks Check water tightness of washing machine connections by turning the tap completely on Periodically check the condition of the hose and replace the hose if necessary Make sure that there is no kink on the hose and that it is not crushed When your washer has two valves The
21. in filter is clogged Check another tap in the house Fully open tap Straighten hose Check the filter of the inlet hose Clean and straighten the drain hose Clean the drain filter Load is too small Load is out of balance The appliance has an imbalance detection and correction system If individual heavy articles are loaded as like bath mat both robe etc this system may stop spinning or even interrupt the spin cycle altogether if the imbalance is too great even after several spin starts If the laundry is still too wet at the end of the cycle add smaller articles of laundry to balance the load and repeat the spin cycle Add 1 or 2 similar items to help balance the load Rearrange load to allow proper spinning See day Is the door opened Close the door If JE is not released call for service Unplug the power plug and call for service e If the water overfills due to the faulty water valve you will get FE display PE is displayed if the water level sensor malfunction Over load in motor Over load in motor Close the water tap Unplug the power plug Call for service Warranty conditions for washing machine 1 The warranty period begins on the purchase date and is valid for 12 months Begin of warranty period is proven if the buyer submits purchase receipt together with the warranty car
22. kdown grounding will reduce the risk of electric shock by providing a path of least resistance for electric current This appliance is equipped with a cord having an equipment grounding conductor and grounding plug The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinance Do not use an adapter or otherwise defeat the grounding plug If you don t have the proper outlet consult an electrician WARNING Improper connection of the equipment grounding conductor can result in risk of electric shock Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded Do not modify the plug provided with the appliance if it does not fit the outlet have a proper outlet installed by a qualified electrician 30 S ei Drawer For detergent and fabric softener Power plug e If the supply cord is damaged it must be replaced by the manufacturer or its service agents or a similarly qualified person in order to avoid a hazard E J Control panel Drain hose Lower cover Drum amp Adjustable feet Drain pump filter J J Lower cover cap Drain plug n Name Front loading washing machine n Power supply 220 240V 50Hz n Size 600mm W x 600mm D x 850mm H n Weight 63kg n Wash capacity 7 0kg n Max Watt 2100W n Spin speed No Spin 400 600 800 WD
23. or cause heavy load to the motor Causing a malfunction Use powder detergent only for the front loading washer Detergent usage may need to be adjusted for water temperature water hardness size and soil level of the load For best results avoid oversudsing Tips Full load according to manufacturer s recommendation Part load 3 4 of the normal amount Minimum load 1 2 of full load e Detergent is flushed from the dispenser at the beginning of the cycle Program FE n Recommended courses according to the laundry type Fabric Type Proper Temp Option Energy in Time in Minutes Whites First check if laundry is machine washable white cotton linen towel and sheets 95 C 60 C 50 C 40 C Pre Wash Eco Rinse Bio Rapid Color fast gaments shirts night dresses pajamas and lightly soiled white cotton underwear 40 C 50 C 60 C Cold 30 C Pre Wash Eco Rinse Bio Rapid Polyamide Acryic Polyester 40 C 50 C 60 C Cold 30 C Pre Wash Eco Rinse Bio Delicate Delicate laundry easily damaged silk curtains 30 C 40 C Cold Rinse Machine washable woolens with pure new wool only 30 C 40 C Cold Rinse Hand Wash marked delicate and wool laundry Cold 30 C 40 C Pre Wash If the laundry is heavily soiled Pre Wash course is effe
24. tart Pause button blinks If Time Delay button is pressed 3 00 is displayed The maximum delayed time is 19 00 hours and the minimum time is 3 00 hours Each pressing of the button advances on time delay by one hour To cancel the time delay press the Power button Time Delay is expected time from the present to the completion of washing cycle or selected process Wash Rinse Spin e According to the condition of water supply and temperature the delayed time and the actual washing time may vary H Gy to use washer Rapid Rapid By pressing the Rapid button Rapid function is selected 1 Rapid Rapid function reduces the whole time including the washing and rinsing time about by half an hour Rapid is available in Whites Coloureds program If lamp turns on that function has been selected Program 9 programs Wool ae Hand Wash are available Peso es Resp a Synihetic according to Coloureds 9 the laundry Wie 0 j type N Program 1 Program When Start Pause button is pressed Coloureds program is automatically selected By turning the Program dial the program is selected in orders of Coloureds U Synthetic u Delicate u Wool U Hand Washu Rinse Spin U Spin U Pumpu Whites Regarding to the laundry type for each program Please refer to the page39 2 Course Whites Delicate Rinse Spin Coloureds Wool Spin Synthetic
25. ubleshooting page50 and follow the guide ZI h r T oe TI 46 3 Completion of washing When washing cycle is completed End is displayed on the Multi display 4 Time left Whites Coloureds around 1 hour and 55 minutes Synthetic around 1 hour and 28 minutes Delicate around 58 minutes Wool Hand Wash around 57 minutes Rinse Spin around 19 minutes Spin around 11 minutes Pump around 1 minute During washing cycle the remaining washing time is displayed Recommended program by manufacturer around 2 hours and 38 minutes around 58 minutes The washing time may vary by the amount of laundry water pressure water temperature and other washing conditions If the imbalance is detected or if the suds removing program works the wash time shall be longer Max increasing time is 45minutes M En Before cleaning the washer interior unplug the electrical power cord to avoid electrical shock to avoid electrical shock hazards n The water inlet filter JE error message will blink on the control panel when water does not enter the detergent drawer If your water is very hard or contains traces of lime deposit the water inlet filter may become clogged It is therefore a good idea to clean it from time to time 1 Turn off the 2 Unscrew the water tap water inlet hose 3 Clean the 4 Tighten up filter using a the inlet hard bristle hos
26. ure s lamp turns on For the more detailed information please refer to the page39 43 H Gy to use washer Child Lock A Time Delay If you want to lock all the buttons to prevent operation by a child or infirm persons this function can be used 1 Child Lock Child Lock can be set by pressing the Temp button and Time Delay button simultaneously Temp Time Delay gt 5 35 an When child lock is set all buttons are inoperable To deactivate Child Lock system press Temp and Time Delay button simultaneously again Temp Time Delay lf you want to change the program when Child Lock is active 1 Press both Temp and Time Delay together 2 Press the Start Pause button 3 Change the desired program and press the Start Pause button ple Time Delay Start Pause Sexi Pause G9 Q E O The child lock can be set at any time and it is automatically canceled when operational errors occur Also Child Lock works when power is off 44 Time Delay Time Delay Time Delay In cnn au gt iam N Time Left Time Left A 4 1 Time Delay Preparing washing before starting Time Delay Turn on the water tap Load laundry and close the door Place the detergent and fabric softener in the drawer How to set Time Delay Press Power button Turn the Program dial to select the program you require Press Time Delay button and set the desired time Press the S
27. water deposits using only cleaners labeled as washer safe n Winterizing instructions If the washer is stored in an area where freezing can occur or moved in freezing temperatures follow these winterizing instructions to prevent damage to the washer 1 Turn off water supply tap 2 Disconnect hoses from water supply and drain water from hoses 3 Plug electrical cord into a properly grounded electrical outlet 4 Add 1gallon 3 8L nontoxic recreational vehicle RV antifreeze to empty wash drum Close door 5 Set spin cycle and let washer spin for 1minute to drain out all water Not all of the RV antifreeze will be expelled 6 Unplug electrical power cord dry drum interior and close door 7 Remove dispenser drawer Drain any water in compartments and dry compartments Replace drawer 8 Store washer in an uprignt position 9 To remove antifreeze from washer after storage run empty washer through a complete cycle using detergent Do not add wash load 49 TEE ee guide This washing machine is equipped with automatic safety functions which detect and diagnose faults at an early stage and react appropriately When the machine does not function properly or does not function at all check the following points before you call the Service Department Symptom Possible Cause Solution Rattling and clanking noise Thumping sound Vibrating noise Foreign objects such as coins or safety pins maybe in drum or
Download Pdf Manuals
Related Search