Pioneer k DVD-RW 16x4 int ATAPI 10pk bulk black
Contents
1. 55____ oi pla Units FYE NEUES EM O10Ah Disc Control Block 0 EIU ee ee Peet re heer a In write operation if Read command or Play Audio command returns the Check Condition the current bit is set to zero b In write operation it keeps previous setting c This Feature indicates that Fixed Packet Writing is allowed If only one Track is existing and the track is invisible or Fixed Packet writing the current bit is set to one d If Audio Track is existing the current bit is set to one Page 23 R8 Series Drive Command Reference Manual Version 0 90 4 4 4 2 Current bit of the Feature List for DVD Media The Current bit of the Feature List for DVD media is set as Table 13 Feature List for DVD ROM R RW Media The State No is described in the Table 8 Media states Table 13 Feature List for DVD ROM R RW Media 6 2 6 3 6 4 7 1 7 2 7 3 7 4 7 5 FooohPrfierist oooth Coe it Tt tt a fff fa fa 00041 Write Protect O0lfo ojo o o r 1 1 1 1 0010h Random Readable Jojr o rjr g o nr rjrii e 0010 MultiRead_ 0 0 0 0 0 0 0 010 010 _001Eh CD OOIFh DVDRead 1 0020 Random Writable 00211 Incremental Streaming Writable o o 1 1 1 o 1 1 1 0 0 0023h Format2. Product Revision Level X XX Reserved Release Date YY MM DD Manufacture s Information Reserved EHE 32 35 4 8 Log Select Command This command is used for checking the drive The specifications of this command are vendor unique 4 9 Log Sense Command This command is used for checking the drive The specifications of this command are vendor unique 4 10 MECHANISM STATUS Command Mechanism Status Parameter List Fault bit Change Status field Current Slot field C DVD Mechanism State field Number of Slots Available field and Length of Slot Table s field are set to zero Page 30 R8 Series Drive Command Reference Manual Version 0 90 4 11 MODE SELECT 10 Command The Save Page function is not supported The SP bit must be set to zero Refer the MODE SENSE Command for the descriptions of each page 4 12 MODE SENSE 10 Command 4 12 1 Mode Parameter Header The Mode Parameter Header format is defined as shown in Table 21 Table 21 Mode Parameter Header ONE MSE Mode Data Length LSB Medium Type Block Descriptor Length always 0000h Page 31 R8 Series Drive Command Reference Manual Version 0 90 The Medium Type was defined in a legacy specification and remains in this drive The Medium Type Codes are defined as shown in Table 22 Table 22 Medium Type Codes 13h 120 mm CD R data and audio combined door closed
3. no more writing to the disc is allowed If not all Fragment in the last Session are closed the drive will terminate this command with CHECK CONDITION Status and sense datawill be set to ILLEGAL REQUEST SESSION FIXATION ERROR INCOMPLETE TRACK IN SESSION In order to assure maximum interchange compatibility with read only devices Guard Zone 2 will be recorded to a device defined PSN that approximates a disc radius of 35 mm The drive closes the last session and finalize the disc Once this close function has been executed no more writing to the disc is allowed If not all Fragment in the last Session are closed the drive will terminate this command with CHECK CONDITION Status and sense datawill be set to ILLEGAL REQUEST SESSION FIXATION ERROR INCOMPLETE TRACK IN SESSION CD R RW Not valid Formatted CD RW DVD R RW Not valid Formatted DVD RW Not valid 110b ot valid Close the last session and finalize the disc Once this close function has been executed no more writing to the disc is allowed If not all Tracks in the last Session are closed the R Drive shall terminate this command with CHECK CONDITION Status and sense data Not valid shall be set to ILLEGAL REQUEST SESSION FIXATION ERROR INCOMPLETE TRACK IN SESSION R DL CD R RW Not valid Formatted CD RW DVD R RW Not valid Formatted RW Not valid 111b Not valid Not valid Er Not valid Page 12 R8 Series Drive Command Ref
4. E Vents rite ere ri gr i e n A o RD ae E n a 46 GET PERFORMANCE Cormitmiand 2 2 RR TRIN C OR ERR E Re ERR Mae ee eed 4 6 1 Performance Type field 00h 4 6 2 Write Speed Type field 03h 4 6 2 1 Write Speed Data for No Media and CD Media E 4 6 2 2 Write Speed Data for No Media and DVD Media 4 7 INQUIRY Gominapngzzsu iecit beet c de et V env c vd devi cen End 4 8 Log Select Command 4 9 Log Sense Command 4 10MECHANISM STATUS Command 4 11 MODE SELECT 10 Command 4 12 MODE SENSE 10 Command 4 12 1 Mode Parameter H eader E 4212 2 5 E R8 Series Drive Command Reference Manual Version 0 90 4 12 2 t Cachlng RR nara EE a Ee ra ADR DAR BLA HE d ERU RE EAE rn xen ee E 4 12 2 2 Error Recovery Parameters Page m 4 12 2 3 P wer Condition Page rer ket de ndr Pit re Er aA reta ca RE ERE Ga 4 12 2 4 Timeout amp Protect estem e tr x eH HU Dx PR ER Rake Ree a Ee ERE 4 12 2 5 Write Parameters M ode Page 4 12 2 6 C DVD Capabilities and Mechanical Status 413PLAY CD Command rtr ird n ede cri d da A doen ae Uo o Te i 4 14 READ 10 READ 12 Command 4 15 READ BUFFER 4 16 READ BUFFER CAPACITY Comman
5. SESSION FIXATION ERROR INCOMPLETE TRACK IN SESSION MPTY OR PARTIALLY WRITTEN RESERVED TRACK NO MORE RZONE RESERVATIONS ARE ALLOWED OWER CALIBRATION AREA ALMOST FULL OWER CALIBRATION AREA IS FULL OWER CALIBRATION AREA ERROR ROGRAM MEMORY AREA RMA UPDATE FAILURE ROGRAM MEMORY AREA RMA IS FULL ROGRAM MEMORY AREA RMA IS almost FULL Z vv Pos 5 wo Pos e os 05 6F 01 05 6F 02 os or e Pos 2 o d Page 46 R8 Series Drive Command Reference Manual Version 0 90 6 Notes 6 1 Skip information in PMA The Skip information is not written to the TOC 6 2 Fixed Packet Size Fixed Packet Size for writing on CD R RW media allows 64KByte only 6 3 Pre gap The Pre gap size is fixed to 2 sec 150 Block For CD Mastering Session at once Write Type must be used Page 47
6. Track RZone Status Indications for R RW Eid Incomplete or Non blank p Incomplete or Partially Full Formatted Complete Complete Incomplete or Blank Incomplete Empty Empty Partially Recorded Incomplete invalid Reserved Blank Reserved _ invalid The NWA V bit is always set to zero for RW because the Next Writable Address field is invalid for such type of media The LRA_V bit is always set to zero for R RW because the Last Recorded Address field is invalid for such type of media For CD R RW media written by SAO the Track Size is computed as follows TrackSize PMAStopTime PMAStartTime 2 This means the last 2 blocks are not encountered as same as the track written by TAO Page 39 R8 Series Drive Command Reference Manual Version 0 90 4 23 RESERVE TRACK RZONE Command For R media up to 15 or 16 fragments can exist in every session When the session is opened by a WRITE command up to 15 fragment can exist When the session is opened by a RESERVE TRACK RZONE command up to 16 fragment can exist Because the last fragment in each session cannot be reserved the limit number of fragments which can be reserved in a session is 14 or 15 When the limit number of complete or reserved fragments are already exist in the session the RESERVE TRACK RZONE command is terminated with Check Condition and SK ASC ASCQ will be set to ILLEGAL REQUEST NO MORE RESERVATION 5 72 05 4 24 SEND DIAGNOSTIC Command This command is defi
7. Valid FOV bit in the Format List Header is set to one the DPRY DCRT STPF IP Try out and VS shall be set to zero In this case the format operation is performed with an Immed function specified by the Immed bit When the FOV bit is set to zero the DPRY DCRT STPF IP Try out Immed and VS shall be set to zero In this case the format operation is performed with the drive s internal default setting The default settng of Immed function is one Even if the format operation is requested with the FOV bit set to one the drive s default setting itself will not be changed 4 3 1 Format Code 001b 4 3 1 1 Format Type 00h Full Format Formatting for the entire media is specified The Number of Blocks field specifies the number of addressable blocks for the entire disc and the Type Dependent Parameter field specifies the Block Length If the Immed function is set to zero the drive will return the status after the format operation has completed If the Immed bit is set to one the drive will return the status as soon as the command descriptor block has been validated and the entire Format Descriptor has been transferred The READ DISC INFORMATION Command the READ TRACK RZONE INFORMATION Command and the TEST UNIT READY Command is used to detect completion of the format operation While format operation is performed by the FORMAT UNIT Command that the Immed function is set to one the drive terminates these commands with the Check C
8. closed is session number 126 when the close session is requested the drive will finalize the disc 011b Not valid Formatted Not valid CD RW DVD R RW Not valid If the last session is complete state and Lead out is not written Lead out shall be appended after the DVD RW last Border out If the last session is intermediate state Border out and Lead out is recorded Page 11 R8 Series Drive Command Reference Manual Version 0 90 Close gs Media Description Function If a background format is in progress the format operation will be stopped and the disc will be structured for removal according to the DVD RW 4 7 Gbytes Basic Format Specifications for the specific purpose of providing DVD RO compatibility To be concrete a partial lead in will be written a temporary lead out will be appended and all unrecorded gaps between lead in and lead out will be format written The radius difference between the start of the temporary lead out and the end of the temporary lead out will approximate 1 mm EU R DL Not valid CD CD R RW Not valid Formatted RW DVD DVD R RW RW Not valid Formatted RW EE e valid R RDL R DL Not Not valid OSE CD R RW Not valid Formatted CD RW DVD R RW Not valid Formatted OR RW ot valid ot valid Not valid Not valid ot valid Um drive closes the last session and finalize the disc Once this close function has been executed
9. command returns the Check Condition the current bit is set to zero Page 25 R8 Series Drive Command Reference Manual Version 0 90 4 5 GET EVENT STATUS NOTIFICATION Command The drive supports polling mode only The Immed bit must be set to one Following Notification Classes are supported Table 15 Notification Class Request Definition Operational Change Request Notification Device Busy 7 4 5 1 Media Events Following Media Events are supported Table 16 Media Event Format The drive has received a request from Eject Request the user to eject the media The drive has received new media and NewMedia is ready to access it Reserved A RW back d f t has BGformatCompleted E completed A RW background format has been BGformatRestarted automatically restarted by the drive Reserved Po ee 006201 4 6 GET PERFORMANCE Command Following Types are supported Table 15 Type field values description T field value Unusable Area DBI Cache Zone 0h Page 26 R8 Series Drive Command Reference Manual Version 0 90 4 6 1 Performance Type field 00h The drive has nominal only performance parameter If Except field dose not set to 006 the drive returns the Performance Header only Table 17 Performance Data Start LBA End LBA End Performance DVD ROM DVD R others DVD RW others No Media CD ROM 1 DVD ROM DVD 12x CAV 12 138
10. completed the SKSV will be cleared to zero Page 16 R8 Series Drive Command Reference Manual Version 0 90 4 3 1 5 Format Type 26h RW Basic Format The Number of Blocks field shall be set to either the value returned by the READ FORMAT CAPACITIES command or OxFFFFFFFF In this drive any other value will be accepted but it is no effect on the format operation The Type Dependent Parameter has the meaning of New format when it has the value 000000h The Type Dependent Parameter has the meaning of Restart format when it has the value 000001h If the field contains any other value the drive will terminate the command with CHECK CONDITION status and set SK ASC ASCQ values to ILLEGAL REQUEST INVALID FIELD IN PARAMETER BLOCK If the Immed function is set to zero then once the foreground format process has completed the command will be terminated with GOOD status If the Immed function is set to one the drive will return the status as soon as the command descriptor block has been validated and the entire Format Descriptor has been transferred While foreground format process is performed by the FORMAT UNIT Command that the Immed function is set to one the drive terminates the READ DISC INFORMATION Command the READ TRACK RZONE INFORMATION Command and the TEST UNIT READY Command with the Check Condition status LOGICAL UNIT NOT READY FORMAT IN PROGRESS 2 04 04 When the background format process is started these commands will
11. of the Streaming bit is no effect on the operation 4 15 READ BUFFER Command This command is used for checking the drive The specifications of this command are vendor unique Page 36 R8 Series Drive Command Reference Manual Version 0 90 4 16 READ BUFFER CAPACITY Command The Block bit is supported When a CD medium is inserted in the drive or no medium is inserted in the drive the Length of Buffer field in the READ BUFFER CAPACITY data is set to 131800h When a DVD medium is inserted in the drive the Length of Buffer field in the READ BUFFER CAPACITY data is set to 188000h If a WRITE command whose Transfer Length exceeds the Blank Length of Buffer value divided by 800h or Available Buffer value the drive terminates the WRITE command with the Check Condition status and set the SK ASC ASCQ values to NOT READY LONG WRITE IN PROGRESS 2 04 08 4 17 READ CAPACITY Command The RelAdr bit is not supported and must set to 0 If empty disc is mounted the Logical Block Address field in the Read Capacity Data is set to zero If a non blank RW disc is mounted the Logical Block Address field in the Read Capacity Data is set to 23053Fh If a disc which is not a RW and has no Complete Session is mounted Logical Block Address field in the Read Capacity Data is set to zero When a CD R RW disc is mounted if it is recorded by Track at once the Logical Block Address field in the Read Capacity Data is set to the LBA immediately behin
12. readable DVD R RW Sequential Recording Profile is current to indicate the sequential writable DVD RW Restricted Overwrite Profile is current to indicate 7 3 formattable DVD ROM Profile is current to indicate the readable DVD RW Sequential Recording Profile is current to indicates erasable DVD RW Restricted Overwrite Profile is current to indicate the restricted overwritable Page 21 R8 Series Drive Command Reference Manual Version 0 90 DVD RW Sequential Recording Profile is current to 7 5 0013h 1 1 indicate erasable DVD RW Restricted Overwrite is current to indicate the restricted overwritable a If the LPP information of the disc does not applicable for the drive to execute write operations the disc is regarded as incompatible media and the Current Profile is set to 0000h b If the LPP information of the disc does not applicable for the drive to execute write operations the Current Profile is set to 0010h 4 4 3 3 Current Profile and Current bit for R RW Media The following table indicates the Current Profile of the Feature Header and the Current bit of the Profile List that R RW media is mounted Table 11 Current Profile and Current bit for R RW Media Current bit of the Profile Current CP CD R CD DYD DVD DVD DVD DVD DVD DVD Profile ROM RW ROM R RW RW RW R R descriptions S W RO S W DL 0008 0009 000A 0010 0011 0013 0014 001A 001B 002
13. set to one the drive terminates these commands with the Check Condition status LOGICAL UNIT NOT READY FORMAT IN PROGRESS 2 04 04 If the drive returns Good status for these command format operation has completed In response to the REQUEST SENSE command including after the Check Condition status described above the drive will return a SK ASC ASCQ values set to NOT READY LOGICAL UNIT NOT READY FORMAT IN PROGRESS with the sense key specific bytes set for progress indication The SKSV will be set to one and the Progress Indication field will contain 16 bit unsigned value such that Progress Indication 65 536 X 100 approximates the percentage of completion of the operation Once the operation is completed the SKSV will be cleared to zero 4 3 1 4 Format Type 15h DVD RW Quick Formatting to create a Intermediate state Border on DVD RW media is specified The created Border will become the only Border on the medium The Number of Blocks field specifies the number of addressable blocks for the new Border and the Type Dependent Parameter field is set to ECC block size 16 The Number of Blocks field may be adjusted to a value less than or equal to the values reported by the READ FORMAT CAPACITIES Command The drive will round the Number of Blocks up to be an integral multiple of the ECC block size This format operation is available on any recording mode and any state of a bordered area If a disc is to be formatted that is in Sequential record
14. to SFFC INF 8090i standard The drive complies to Information Technology Multimedia Commands 4 MMC 4 Draft Revision 1f prior to SFFC INF 8090i standard when a R or a RW disc is inserted in the drive In some cases the drive executes unique operation which is not described in the standards This document describes details of such unique operation for each command or disc For More Information about SFFC INF 8090i refer FTP site at ftp ftp avc pioneer com Mtfuji5 Spec For More Information about Information Technology Multimedia Commands 4 4 Draft Revision 1f refer a site at http www t10 org drafts htm Page 3 R8 Series Drive Command Reference Manual Version 0 90 2 Interface The drive supports ATA ATAPI interface 2 1 ATA ATAPI version The drive complies with the ATA ATAPI 5 Specification and supports following transfer mode PIO Mode 4 Multi Word DMA Mode 2 Ultra DMA Mode 4 Ultra DMA 66 2 2 Drive Information The data returned by INQUIRY command covers the following information Vendor name PIONEER Product collation data DVD RW DVR 108 Page 4 R8 Series Drive Command Reference Manual Version 0 90 3 R6 Series DRIVE Descriptions 3 1 Compatible Media The R8 series drive unit hereinafter referred to as drive supports reading of CD ROM R RW Disc DVD ROM R RW RAM Disc and R RW Disc and writing of CD R RW Disc DVD R RW Disc and R RW Disc 3 1 1 DVD ROM Disc A DVD ROM disc
15. 120 mm CD R data and audio combined doorclosed o O 15h 120 mm multi session CD RW door closed 28h 80 mm multi session CD RW door closed 29h 40h Reserved 48h Reserved 48h 80 mm muti border session DVD R RW sR door closed __ O Page 32 R8 Series Drive Command Reference Manual Version 0 90 4 12 2 Mode Pages The drive is not supported the Parameters Savable PS bit and must be set to zero The Page Code field identifies the format and parameters defined for that mode page The drive supports following Mode pages Table 23 Mode Page Codes 05h om dT om page 33 Eh CD AndioControlPage 0 1Ah Power Condition Page 41223 onpage33 Dn Timeout amp Protect Page 41224 onpage34 35 O 3Fh Return all pages valid only for the MODE SENSE command 4 12 2 1 Caching Page The Caching Page is supported for compatibility of other CD R RW drive This page has no effect on write read operation The returned Caching parameters by the MODE SENSE 10 Command are modified to the new parameters after receiving new parameters by MODE SENSE 10 Command Table 24 Caching Parameter pL guess S Hee Page Code 08h Page Length a CAP DISC 82 wee RCD Demand Read Priority Write Retention Priority MSB Disable Pre fetch Transfer Length LSB MSB Minimum Pre fetch LSB MSB Maximum Pre fetch
16. 1Eh CD Read 001Fh DVD Read 0020h Random Writable 0021h Incremental Streaming Writable 0023h Formattable 0026h Restricted Overwrite 0029h DRT DM 002Ah DVD RW 002Bh DVD R 002Ch DVD RW Restricted Overwrite 002Dh CD Track at Once 002Eh CD Mastering 002Fh DVD R RW Write 003Bh DVD R Double Layer 0100h Power Management 0103h CD Audio analog play 0104h Microcode Upgrade 0105h Time out 0106h DVD CSS 0107h Real Time Streaming 0108h Logical Unit serial number 010Ah Disc Control Block 010Bh DVD CPRM The DVD RW feature and the DVD R feature are defined in 4 other features are defined in SFFC INF 8090i Supported Profile is listed to Table 7 Profile List Table 7 Profile List Page 18 R8 Series Drive Command Reference Manual Version 0 90 002Bh DVD R Double Layer The DVD RW profile and the DVD R profile are defined in MMC4 All other profiles are defined in SFFC INF 8090i 4 4 2 Media states The Morphing is occurred when the media or media state is changed The drive has Media states that is described in the Table 8 Media states Table 8 Media states 1 NeMedia NotRedy 2 CDROM Session closed Disc Session at Once writing or Session closed disc Existing Complete Session Appendable Not appendable Disc Disc at Once writing or Finalized disc Empty or Blanked Disc No Session closed Disc Track at Once or Packet writing disc Existing Complete Session 45 Full forma
17. 385 569h DVD Ix CLV 1 1385 1385 569h DVD Ix CLV 1 1385 1385 569h DVD Ix CLV 1 1385 1385 569h DVD Ix CLV 1 1385 1385 569h DVD Ix CLV 1 1385 1385 569h DVD Ix CLV 1 1385 1385 569h Page 29 Write Speed End LBA Read Speed Write Speed Descriptor Last LBA Last LBA Last LBA DVD 4x CLV 4 1385 5540 15A4h DVD 2x CLV 2 1385 2770 AD2h DVD Ix CLV 1 1385 1385 569h DVD 4x CLV 4 1385 5540 15A4h DVD 2x CLV 2 1385 2770 AD2h DVD Ix CLV 1 1385 1385 569h DVD 2x CLV 2 1385 2770 AD2h DVD Ix CLV 1 1385 1385 569h DVD Ix CLV 1 1385 1385 569h DVD 2x CLV 2 1385 2770 AD2h DVD Ix CLV 1 1385 1385 569h DVD Ix CLV 1 1385 1385 569h DVD 4x CLV 4 1385 5540 15A4h DVD Ix CLV 2 4 1385 3324 CFCh DVD Ix CLV 2 4 1385 3324 CFCh DVD Ix CLV 2 4 1385 3324 CFCh R8 Series Drive Command Reference Manual Version 0 90 4 7 INQUIRY Command CmdDt bit bit and Page Code or Operation Code field does not supported These bit or field must be set to 0 The drive returns following 96bytes Inquiry data Table 20 INQUIRY Data Format eed E E E Peripheral Device Type 05h RMB 1 Reserved ISO Version Oh ECMA Version 0h Transport Version 3h ANSI Version Oh Response Data Format 2h Additional Length 35h Reserved Reserved Reserved Vendor Identification PIONEER _ Product Identification DVD RW DVR 108
18. 3h CD 4x CLV 4 2352 75 1000 705 2C Ih CD 16x CLV 16 2352 75 1000 2116 844h CD 12x CLV 12 2352 75 1000 2822 B06h CD 8x CLV 8 2352 75 1000 1411 583h CD 4x CLV 4 2352 75 1000 705 2C1h CD 16x CLV 10 2352 75 1000 1764 6E4h CD 4x CLV 4 2352 75 1000 705 2C 1h CD 4x CLV 4 2352 75 1000 705 2C Ih R8 Series Drive Command Reference Manual Version 0 90 4 6 2 2 Write Speed Data for No Media and DVD Media Table 19 Write Speed Data for DVD Media Vo Outermost Lead out Start LBA in LPP 1 DVD R 4x Outermost Lead out Start LBA in LPP 1 Outermost Lead out Start LBA in LPP 1 Vo Outermost Lead out Start LBA in LPP 1 DVD R 2x Outermost Lead out Start LBA in LPP 1 DVD R 1x Outermost Leac out Start LBA in LPP 1 Outermost Lead out Start LBA in LPP 1 DVD RW 2x Outermost Lead out Start LBA in LPP 1 Outermost Lead out DVD RW 1 Ix Start LBA in LPP 1 Outermost Lead out Start LBA in ADIP 1 Outermost Lead out Start LBA in ADIP 1 R Q4x Outermost Lead out Start LBA in ADIP 1 Outermost Lead out RW 2 4 29 Start LBA ADIP 1 DVD Ix CLV 1 1385 1385 569h DVD Ix CLV 1 1385 1385 569h DVD Ix CLV 1 1385 1385 569h DVD Ix CLV 1 1385 1385 569h DVD Ix CLV 1 1385 1385 569h DVD Ix CLV 1 1385 1385 569h DVD Ix CLV 1 1385 1385 569h DVD Ix CLV 1 1385 1385 569h DVD Ix CLV 1 1385 1385 569h DVD Ix CLV 1 1385 1
19. 5 240 585 6818 1AA2h CD 32x CAV 32 2352 75 1000 240 585 2315 90Bh CD 32x CAV 32 2352 75 1000 240 585 2315 90Bh DVD 12xCAV 12 1385 240 585 6818 1 2 DVD 6x 6 1385 240 585 3409 D51h DVD 2x CLV 2 1385 2770 AD2h 6x CAV 6 1385 240 585 6818 1AA2h DVD 4x CLV 4 1385 5540 15A4h Only the Performance Header is returned Established Write Speed Only the Performance Header is returned Established Write Speed Established Write Speed Page 27 Lead out Start LBA of Last Session 1 Outermost Lead out Start LBA from ATIP 1 Last LBA Outermost Lead out Start LBA in LPP 1 Outermost Lead out Start LBA in LPP 1 Outermost Lead out Start LBA in ADIP 1 Outermost Lead out Start LBA in ATIP 1 Outermost Lead out Start LBA in LPP 1 Outermost Lead out Start LBA in ADIP 1 DVD 12x CAV 12 1385 16620 40ECh CD 32x CAV 32 2352 75 1000 5644 160Ch CD 32x CAV 32 2352 15 1000 5644 160Ch DVD 12x 12 1385 16620 40ECh DVD 6x CAV 6 1385 8310 2076h DVD 2x CLV 2 1385 2770 AD2h DVD 6x CAV 6 1385 8310 2076h DVD 4x CLV 4 1385 5540 15A4h Established Write Speed Established Write Speed Established Write Speed R8 Series Drive Command Reference Manual Version 0 90 4 6 2 Write Speed Type field 03h 4 6 2 1 Write Speed Data for No Media and CD Media Table 18 Write Speed Data for No Media and CD Med
20. B EE Only DVD R Profile is current Only DVD RW Profile is current Only DVD R Profile is current Page 22 8 Series Drive Command Reference Manual Version 0 90 4 4 4 Current bit of the Feature List 4 4 4 1 Current bit of the Feature List for CD Media The Current bit of the Feature List for CD media is set as Table 12 Feature List for CD Media The State No is described in the Table 8 Media states Table 12 Feature List for CD Media tpe epe ien Feature Name 0002 Morphing tiie Removable Medi 0004h Write Protect apo LEER OO1Fh DVD DVD Read 0020h Random Writable 0021h Incremental EI Writable 0023h Formattable Formattable EsenEWESERESES 1 epe p p 0029h Software Defect Management o 0 0 ee e e egere o o e e n 0 0 0 002Dh CD Track atOnce LER H too 0 tio oo 002Fh DVD R RW Write 0 corr or TEC ER RE CR ERE 01008 PowerManagement f f f f f f f f f f ply po Paaa o pajaja o 0104h Microcode Upgrade emea 0106
21. CD RW and DVD RW media The Immed bit is supported The READ DISC INFORMATION Command the READ TRACK RZONE INFORMATION Command and the TEST UNIT READY Command is used to detect completion of the blank operation While blank operation is performed by the BLANK Command that the Immed bit is set to one the drive terminates these commands with the Check Condition status LOGICAL UNIT NOT READY OPERATION IN PROGRESS 2 04 07 The drive supports following Blanking Type for CD RW and DVD RW media Table 2 Blank Type BlankaTrack PnP Page 9 R8 Series Drive Command Reference Manual Version 0 90 4 2 CLOSE TRACK RZONE SESSION BORDER Command The Immed bit is supported The READ DISC INFORMATION Command or READ TRACK RZONE INFORMATION Command is used to detect completion of the close operation While close operation is performed by the CLOSE TRACK RZONE SESSION BORDER Command that the Immed bit is set to one the drive terminates these commands with the Check Condition status LOGICAL UNIT NOT READY OPERATION IN PROGRESS 2 04 07 Note The TEST UNIT READY Command can not use to identify the completion of close operation because the this command returns Good status while close operation is performed The Session Border bit and the Track RZone bit specified in SFFC INF 8090i are extended to the Close Function field specified in 4 as follows Table 3 Close Function field definition Close ee Media Descriptio
22. LSB Maximum Pre fetch Ceiling Default value of the WCE bit is one Default value of any other bits and field is zero 4 12 2 2 Error Recovery Parameters Page The AWRE and ARRE bits are not supported and are ignored The TB RC DTE and DCR bits are ignored The Write Retry Count field is reserved The PER bit and EMCDR field are used to control the defect reporting 4 12 2 3 Power Condition Page The default value of an Idle bit is one The default value of the Idle Timer field is 00000258 1 minute The default value of the Standby bit is one The default value of Standby Timer field is 000012 8 minutes Page 33 R8 Series Drive Command Reference Manual Version 0 90 4 12 2 4 Time out amp Protect Page The DISP SWPP bits are not supported and must be set to 0 4 12 2 5 Write Parameters Mode Page The parameters specified in the Write Parameters Mode Page are not applicable to R RW media The parameters specified in the Write Parameters Mode Page are not applicable to formatted DVD RW media The default value of the BUFE bit is 1 If LS V bit is set to one the Link Size field must be set to 7h for CD R RW or 10h for DVD R RW If LS V bit is set to zero the drive assumes the Link Size of 7h for CD R RW or 10h for DVD R RW The default value of the LS V bit is 1 and the default value of the Link Size field is 1Oh The drive supports following Write Type Table 25 Write Type Field Value Definition f
23. NA et ar E D Ideas 4 3 1 Format Code 001b sess 4 3 1 1 Format Type 00h Full Format 4 3 1 2 Format Type 10h C DVD RW Full Format 4 3 1 3 Format Type 13h DVD RW Quick Grow the last Border 4 3 1 4 Format Type 15h DVD RW Quick 4 3 1 5 Format Type 26h RW Basic Format 4 3 2 Format Code S LT1D cette frente ctetuer M teeter Ey aga vada ER d ua eR DRE gn UR ERREUR RA GRE ERR GR DAE 4 4 GET CONFIGURATION Command 4 4 1 Feature List and Profile List 4 4 2 M amp dia Stales a nece dea d edad ed dee E a 4 4 3 Current Profile of the Feature Header and Current bit of the Profile List Gs 4 4 3 1 Current Profile and Current bit for No Media and CD Media essent nnns 4 4 3 2 Current Profile and Current bit for DVD Media esses tenente teta tasa totae tata 4 4 3 3 Current Profile and Current bit for R RW Media i 444 C rrent bit of the Feature ISten m ceret EAE areae 4 4 4 1 Current bit of the Feature List for CD Media eenennnntnrn nnne rnnt nennt etta sa tens 4 4 4 2 Current bit of the Feature List for DVD Media sees nnne nnn nnn tnter n tn tn tata sns nenene 4 4 4 3 Current bit of the Feature List for R 4RW Media sess eene nennt nter rnnt natant ta 4 5 GET EVENT STATUS NOTIFICATION Command us 4 5 1 M dia
24. ODE PARAMETERS CHANGED INCOMPATIBLE MEDIUM INSTALLED CANNOT READ MEDIUM INCOMPATIBLE FORMAT CANNOT WRITE MEDIUM INCOMPATIBLE FORMAT MEDIUM FORMAT CORRUPTED FORMAT COMMAND FAILED MEDIUM NOT PRESENT INTERNAL TARGET FAILURE LOGICAL UNIT FAILED SELF CONFIGURATION OVERLAPPED COMMANDS ATTEMPTED ERASE FAILURE ERASE FAILURE Incomplete erase operation detected MEDIA LOAD OR EJECT FAILED MEDIUM REMOVAL PREVENTED SYSTEM RESOURCE FAILURE o elo elo coi cio elo 2 o t2 to t2 05 04 Los Lv NN Lo Lv EN NN EUH Page 45 R8 Series Drive Command Reference Manual Version 0 90 Description Sense asc asco y UNABLE TO RECOVER TABLE OF CONTENTS ILLEGAL MODE FOR THIS TRACK OPY PROTECTION KEY EXCHANGE FAILURE AUTHENTICATION FAILURE COPY PROTECTION KEY EXCHANGE FAILURE KEY NOT PRESENT COPY PROTECTION KEY EXCHANGE FAILURE KEY NOT ESTAB LISHED EAD OF SCRAMBLED SECTOR WITHOUT AUTHENTICATION EDIA REGION CODE IS MISMATCHED TO LOGICAL UNIT REGION RIVE REGION MUST BE PERMANENT REGION RESET COUNT ERROR ESSION FIXATION ERROR ESSION FIXATION ERROR WRITING LEAD IN ESSION FIXATION ERROR WRITING LEAD OUT
25. R8 Series Drive Command Reference M anual Version 0 90 August 6 2004 PIONEER CORPORATION R8 Series Drive Command Reference Manual Version 0 90 m 3 2 NCCT ACs 2 tote cc nate 4 gione Y 4 2 2 DriVe nire dy ziuje que ep 4 Series DRIVE Descriptions noe eis teet a eec tr ep etu use 5 3 1 Compatible M eda ht erre fene ade a amine 5 3 1 1 DVDROM BILE 5 32 DVD R BIC a E A A E 5 3 L3 DVD RW DISC ete enia ate UR n CR He ited eal dt e 3 1 4 DVD RAM Disc 31 6 4R IDL PIC H 3 1 7 4RW Disc 3 1 8 CD ROM Disc 3 1 9 CDR 0 MM 3 2 H M 3 3 Authentication 3 4 Defect Management 4 Packet Commands ERR RR T eR e eR eee AM BLANK Command 4 2 CLOSE TRACK RZONE SE SSI ON BORDER nennen tnter ran 4 3FORMAT UNIT COMMA
26. READY Command is terminated with Check Condition on the following conditions Table 39 Error Code of Test Unit Ready Command Key LOGICAL UNIT IS IN PROCESS OF BECOMING READY While Tray Loading and set up operation Format operation for CD RW or DVD RW is LOGICAL UNIT NOT READY FORMAT IN P meee 04 04 performing or foreground format operation is PROGRESS performing for RW 04 07 LOGICAL UNIT NOT READY OPERATION IN Blank Bake d PROGRESS ank operation is performing 00 POWER ON RESET OR BUS DEVICE RESET OCCURRED NOT READY TO READY CHANGE MEDIUM m Transition from Not Ready to Ready has occurred MAY HAVE CHANGED EDIUM NOT PRESENT Compatible Media is not exist Note 1 When write operation is performing the TEST UNIT READY Command returns Good status Completion of the write operation is identified by the READ DISC INFORMATION or READ TRACK RZONE INFORMATION Command When write operation is performing these command is terminated with Check Condition status LOGICAL UNIT NOT READY OPERATION IN PROGRESS 2 04 07 When write operation is completed these command returns Information data and Good status 29 Unit Attention has generated Note 2 When background format operation is performing the TEST UNIT READY Command returns Good status Completion of the write operation is identified by the READ DISC INFORMATION Command When BG format operation is performing the BG Format Status field in the Disc Informa
27. age shall be set to zero This format operation is available on any recording mode and any state of a bordered area The number of RZone in the created Border is one after this operation Page 15 R8 Series Drive Command Reference Manual Version 0 90 4 3 1 3 Format Type 13h DVD RW Quick Grow the last Border Formatting to expand the last Border and enter the last bordered area into intermediate state of a DVD RW medium is specified The Number of Blocks field specifies the number of addressable blocks to be added to current Border capacity and the Type Dependent Parameter field is set to ECC block size 16 The drive will round the Number of Blocks up to be an integral multiple of the ECC block size This format operation is available only when the disc is in Restricted overwrite mode and the last bordered area is complete state The number of bordered areas and RZones does not change after this operation If the Immed function is set to zero the drive will return the status after the format operation has completed If the Immed bit is set to one the drive will return the status as soon as the command descriptor block has been validated and the entire Format Descriptor has been transferred The READ DISC INFORMATION Command the READ TRACK RZONE INFORMATION Command and the TEST UNIT READY Command is used to detect completion of the format operation While format operation is performed by the FORMAT UNIT Command that the Immed function is
28. be terminated with GOOD status As for the REQUEST SENSE command while the foreground format process is performed the drive will return a SK ASC ASCQ values set to NOT READY LOGICAL UNIT NOT READY FORMAT IN PROGRESS 2 04 04 without the sense key specific bytes set for progress indication While the background format process is performed the drive will return a SK ASC ASCQ values set to NO SENSE FORMAT IN PROGRESS 0 04 04 with the sense key specific bytes sa for progress indication The SKSV will be set to one and the Progress Indication field will contain 16 bit unsigned value such that Progress Indication 65 536 X 100 approximates the percentage of completion of the background format process Once the background format process is completed the SKSV will be cleared to zero 4 3 2 Format Code 111b This Format Code has a legacy definition for CD RW It is described in Annex E of the MMC 4 The SESS and Grow bits are ignored by the drive The drive performs as same as the operation which the Format Code is set to 001b and the Format type is set to 00h Page 17 R8 Series Drive Command Reference Manual Version 0 90 4 4 GET CONFIGURATION Command 4 4 1 Feature List and Profile List Supported Feature is listed to Table 6 Feature List Table 6 Feature List Feature Number Feature Name 0000h Profile List 0001h Core 0002h Morphing 0003h Removable Medium 0004h Write Protect 0010h Random Readable 001Dh Multi Read 00
29. d 4 17 READ CAPACITY Commandeer rnana Aa a A A SEAE EA eR EH ERR RR RO 4 18 READ DISC INFORMATION Command teen nnns 4 19 READ DVD STRUCTURE Command 4 20 READ HEADER Command tenerte ne eu EH inna natin AA URL 4 21 READ TOC PMA ATIP iret rtr inris Lin rend Dn Tekken a c ek rn har ace 4 22 READ TRACK RZONE INFORMATION Command eene entente nnne nennen entente tenente retener ens 4 23 RESERVE TRACK RZONE Command sees a tete reete tite tenente tenentes tente 4 24 SEND DIAGNOSTIC Command 4 25 SEND DVD STRUCTURE Command nanan ra dm 4 26 SET CD SPEE D COMANA enn nitri eee v ien n pec ein den rented 4 27 SET STREAMING Command 4 28 TEST UNIT READY Command 4 29 VERIFY 10 Command ne 4 30 WRITE 10 WRITE 12 Command iss ice tret ee x rere D Fer Fi ne uM 45 6 1 Skip information in PMA 6 2 Fixed Packet Size edd Page 2 R8 Series Drive Command Reference Manual Version 0 90 1 Introduction This document specifies a command set for the PIONEER 8 series drive The drive fundamentally complies
30. d of the outermost Lead out so 2 Run out blocks will be encountered 4 18 READ DISC INFORMATION Command For R media the Last Session Lead in Start Address is the LBA of where the next Intro shall be recoded If no session exists on the disc then the value returned is 00000000h If the disc has complete status then the value returned is FFFFFFFFh For R media the Last Possible Lead out Start Address is the LBA found in the ADIP of the disc s lead in If the disc has complete status then the value returned is FFFFFFFFh The OPC table is not supported for R RW media 4 19 READ DVD STRUCTURE Command Following Format codes are supported Table 28 Format Code for READ DVD STRUCTURE command Format Returned Data Description Code 04h RMD in last Border out Returns the Field of RMD in last Border out of the DVD R RW disc Returns RMD sectors which recorded in RMA of the DVD R RW disc Unique Disc Identifier Returns Unique Disc Identifier of the DVD R RW disc Physical in the Lead in Returns Physical format information of Control Data zone in the Lead in Layer boundary Returns DVD R Double Layer Recording information information Disc Control Blocks Returns the Disc Control Block identified by the Content Descriptor Return the Write Protection Status Returns a list of DVD structure present in the specified Layer i i Page 37 R8 Series Drive Command Reference Manual Version 0 90 4 20 READ HEADER Command Th
31. e The C DVD Capabilities and Mechanical Status Page format is defined as shown in Table 27 Table 27 C DVD Capabilities and Mechanical Status Page Format Ey px pog xg 0 PS Reserved Page Code 2Ah Page Length 3Eh Reserved 5 CD R Read 1 Multi Digital Digital Composite Audio Play session Port 2 Port 1 0 Read Bar RW CDDA Code Pointers Stream Supported Accurate 1 Capable Supported Reserved j Frevent Lock State current state RW in Side S W Slot 500018 Separate Disc Lead in Change Selection Channel Readable Capable SSS Poo Mute 1 Maximum Read Speed Supported Number of Volume Levels Supported 0100h LSB N Buffer Size supported by Logical Unit 07D0h 95 LSB A MSB MSB Current Read Speed LSB Reserved Reserved 00b 0 MSB Maximum Write Speed Supported N MSB Current Write Speed N LSB N MSB Copy Management Revision Supported 0001h N o LSB Reserved Rotation Control Selected 000000b N 4 N Current Write Speed Selected 2 17 18 N Page 35 R8 Series Drive Command Reference Manual Version 0 90 px ee eee wel 3 Number of Logical Unit Write Speed Performance Descriptor Tables LSB 32 Reserved 00h Reserved Rotation Control 1 000000b 00b 35 Write Speed Sup
32. e speed Table 36 Parameters to set Writing speed for CD R RW media CD R Writing CD RW Writing Write Size Write time Speed Speed 0000h 0001h FFFFh 32x CLV 24x ZCLV 0000h 06E3h 4x CLV 4x CLV 06E4h 0BO6h 10x CLV 10x CLV GNE ODC7h EE CLV 16x CLV ODCsSh 1089h 1089h 20 2 ZCLV 108Ah 160Bh 24x ZCLV 24x ZCLV 160Ch FFFFh 32x ZCLV Table 37 Parameters to set Writing speed for DVD R RW media pi i TEN DVD R DVD RW Write Size Write time S Writing Speed Writing Speed 0000h 0001h FFFFh 16x ZCLV 4x CLV 0000h OAD 1h Ix CLV 1x CLV 15A3h 2x CLV 2x CLV 03E8h 15A4h 2075h Table 38 Parameters to set Writing speed for R RW media Write Si Write ti IR oe rite rite time 5 Writing Speed Writing Speed 0000h 0001h FFFFh 16x ZCLV 4x CLV 40ECh 568Fh 12x ZCLV 5690h FFFFh 16x ZCLV The writing speed is set to the drive regardless of currently mounted media Even if no media is mounted in the drive the writing speed can be set If the set writing speed cannot be applied for mounted media in a write operation the actual writing speed is reduced to the writing speed which is applicable to the media 0000h 15A3h 24x CLV 24x CLV 15A4h 2075h 4x CLV 2076h 2B47h 6x CLV 2B48h 40EBh 8x ZCLV 4x CLV Page 42 R8 Series Drive Command Reference Manual Version 0 90 4 28 TEST UNIT READY Command The TEST UNIT
33. ecording digitized audio and digital data 3 1 9 CD R Disc Compact Disc Recordable CD R is a standardized medium defined by the Orange Book Part 2 The CD R system gives the opportunity to write once and read many times CD information 3 1 10 CD RW Disc Compact Disc Rewritable CD RW is a standardized medium defined by the Orange Book Part 3 The CD RW system gives the opportunity to write erase overwrite and read CD information 3 2 Power Condition The drive is provided with 4 power conditions including active idle standby and sleep The power consumption in the active and idle conditions is identical while that in the standby and sleep conditions is also identical The disc keeps rotating in the active and idle conditions while it is stopped in the standby and sleep conditions Page 5 R8 Series Drive Command Reference Manual Version 0 90 3 3 Authentication The copy protection system for DVD ROM disc is CSS or CPPM copy protection system The drive supports the CSS CPPM authentication The copy protection system for DVD R RW disc is CPRM copy protection system The drive supports the authentication 3 4 Defect Management The drive supports distributed real time defect management DRT DM model in the software defect management model The drive supports small DBI cache memory model Page 6 R8 Series Drive Command Reference Manual Version 0 90 4 Packet Commands The following commands are i
34. erence Manual Version 0 90 Page 13 R8 Series Drive Command Reference Manual Version 0 90 4 3 FORMAT UNIT Command The CmpLst bit is not supported and must be set to zero The Interleave Value field is not supported and must be set to zero The Format Code field allows the value of 001b and 111b If Format Code field is set to 001b and a CD RW or a DVD RW media is mounted the drive conforms for the definition of SFFC INF 8090i If Format Code is set to 001b and a RW media is mounted the drive conform for the definition of 4 If Format Code is set to 111b and CD RW media is mounted the drive conforms for legacy specifications which is described in the definition of MMC 4 The drive supports following Format Type for each media Table 4 Format Code 001b S t f S t fi Format NU dnd LM QE Support for Name CD RW DVD RW j RW media media media Full Format C DVD RW Full Format T IC UT TT em 158 DVD RW Quick Grow the last Border ye DVD RWQuikAddBorer m ish DVD RWQuik j Table 5 Format Code 111b CD RW only Grow bit Support for CD RW media 1 The Format Unit parameter list shall be transferred from the Host to the drive The data sent to the drive consists of a Format List Header followed by one Format descriptor so the parameter list length is always 12 bytes When the Format Options
35. even if the disc is changed the previously set writing speed is available However only for CD media the writing speed can be set also by a SET CD SPEED command The performance settings for CD and DVD are not independent from each other The available writing speed may be restricted by the drive when the characteristic of media is not suitable for the speed Table 35 Available Writing speed for each media E 10x CLV x CLV e 5 24x ZCLV 20x ZCLV 16x CLV D RW Ult d e 10 DVD R 1x IxCLV DVD R 1 4x 4x CLV 2x CLV 1x CLV SSS 12x ZCLV 16xZCLV 8x ZCLV Writing speed of 12x and 16x is only available for 6x CLV 4x CLV specific media DVD RW 1x 1x CLV DVD RW 1 2 OxCLV IXCLV 02 DVD RWQ 49 4xCLV2XCLV R 1 7 CLV 2 4x CLV R 1 8 12x ZCLV 16xZCLV 8x ZCLV Writing SS SI of 12x and 16x is only available for 6x CLV 4x CLV specific media Page 41 DVD R 1 8x R8 Series Drive Command Reference Manual Version 0 90 4x CLV 2 4 CLV Writing speed of 4x is only available for specific media RW 1 24x 24x CLV RW 1 49 4x CLV 24x CLV The setting of the RDD Exact and MRW bits and the Start LBA End LBA Read Size and Read Time fields ignored The specified writing speed will apply to whole disc area It is recommended to use the following values in order to set the writ
36. ia ine Speed End LBA Read Speed Write Speed Descriptor CD RW High Speed 1 2 3 4 1 2 3 4 1 2 3 4 1 2 1 Lead out Start LBA of Last Session 1 Lead out Start LBA of Last Session 1 Lead out Start LBA of Last Session 1 Lead out Start LBA of Last Session 1 Outermost Lead out Start LBA from ATIP 1 Outermost Lead out Start LBA from ATIP 1 Outermost Lead out Start LBA from ATIP 1 Outermost Lead out Start LBA from ATIP 1 Outermost Lead out Start LBA from ATIP 1 Outermost Lead out Start LBA from ATIP 1 Outermost Lead out Start LBA from ATIP 1 DVD Ix CLV 1 1385 1385 569h DVD Ix CLV 1 1385 1385 569h DVD Ix CLV 1 1385 1385 569h DVD Ix CLV 1 1385 1385 569h CD 4x CLV 4 2352 75 1000 705 2C 1h CD 4x CLV 4 2352 75 1000 705 2C 1h CD 4x CLV 4 2352 75 1000 705 2C Ih CD 4x CLV 4 2352 75 1000 705 2C 1h CD 4x CLV 4 2352 75 1000 705 2C 1h CD 4x CLV 4 2352 75 1000 705 2C1h CD 4x CLV 4 2352 75 1000 705 2C 1h CD 4x CLV 4 2352 75 1000 705 2C1h CD 4x CLV 4 2352 75 1000 705 2C 1h CD 4x CLV 4 2352 75 1000 705 2C 1h CD 4x CLV 4 2352 75 1000 705 2C 1h Page 28 DVD 4x CLV 4 1385 5540 15A4h DVD 2 4x CLV 2 4 1385 3324 CFCh DVD 2x CLV 2 1385 2770 AD2h DVD Ix CLV 1 1385 1385 569h CD 16x CLV 16 2352 75 1000 2116 844h CD 12x CLV 12 2352 75 1000 2822 B06h CD 8x CLV 8 2352 75 1000 1411 58
37. ies to indicate the read only 000Ah CD RW Profile is current to indicate the writable 000Ah CD RW Profile is current to indicate the writable 000AR CD ROM Profile is current IEBEREE to indicate the readable 4 5 000Ah E Profile is current to indicate the writable 3 3 Page 20 R8 Series Drive Command Reference Manual Version 0 90 4 4 3 2 Current Profile and Current bit for DVD Media The following table indicates the Current Profile of the Feature Header and the Current bit of the Profile List that DVD media is mounted Table 10 Current Profile and Current bit for DVD Media bit of im Current ae km Profile iu E aw escriptions e 0008 0009 000A 0010 P ve 001A 001B 002 DVD ROM Profile is current 010h 5 to indicate the read only DVD R Sequential Recording Profile is current to indicate the sequential writable DVD R Sequential Recording Profile is current to indicate the sequential writable DVD ROM Profile is current to indicate the readable DVD R Sequential Recording Profile is current to indicate the Recording Profile is current to indicate the sequential writable DVD RW Restricted Overwrite Profile is current to indicate formattable DVD R RW Sequential Recording Profile is current to indicate the sequential writable DVD RW Restricted Overwrite Profile is current to indicate formattable DVD ROM Profile is current to indicate the
38. ing mode new intermediate state bordered area is created at the beginning of the disc and the recording mode is changed to Restricted overwrite mode The number of RZone in the created Border is one after this operation If the Immed function is set to zero the drive will return the status after the format operation has completed If the Immed bit is set to one the drive will return the status as soon as the command descriptor block has been validated and the entire Format Descriptor has been transferred The READ DISC INFORMATION Command the READ TRACK RZONE INFORMATION Command and the TEST UNIT READY Command is used to detect completion of the format operation While format operation is performed by the FORMAT UNIT Command that the Immed function is set to one the drive terminates these commands with the Check Condition status LOGICAL UNIT NOT READY FORMAT IN PROGRESS 2 04 04 If the drive returns Good status for these command format operation has completed In response to the REQUEST SENSE command including after the Check Condition status described above the drive will return a SK ASC ASCQ values set to NOT READY LOGICAL UNIT NOT READY FORMAT IN PROGRESS with the sense key specific bytes set for progress indication The SKSV will be set to one and the Progress Indication field will contain 16 bit unsigned value such that Progress Indication 65 536 X 100 approximates the percentage of completion of the operation Once the operation is
39. is command is defined in a legacy specification MMC 2 Revision 10a 4 21 READ TOC PMA ATIP Command The ADR Control field for DVD media is always set to 14h 4 22 READ TRACK RZONE INFORMATION Command The Damage bit is supported for DVD R RW media It is always set to zero for the other media The Copy bit is not supported It is always set to zero The Track Mode field is constantly set to 4h for DVD and R RW media The RT Blank Packet Inc and FP bits are sets as following Table 29 and Table 30 The Packet Inc and FP bits are always set to zero for R RW Table 29 Track RZone Status Indications for CD ROM R RW and DVD ROM R RW Packet Inc CD ROM R RW DVD ROM R RW Write Method Write Method Pre mastered Pre mastered Complete Complete DAO I let Complete Restricted Complete or Fixed Incomplete h Overwrite Incomplete TAO Variable Fixed Blank Invalid Restricted SVO yn Overwrite TAO SAO Compete Complete Variable Partially Recorded Incremental Reserved Reserved Complete i Partially Recorded Invalid Reserved Empty Reserved Empty Reserved 0 Invalid Incremental Empty Reserved 1 Invalid Invalid 1 aes en FP 1 1 e ele elo _ ES 1 38 R8 Series Drive Command Reference Manual Version 0 90 Table 30
40. is specified by DVD Specifications for Read Only Disc The drive can read the Single Layer disc and the Dual Layer Parallel track path and Opposite track path disc 3 1 2 DVD R Disc A DVD R disc is specified by DVD Specifications for Recordable Disc for General The drive can read and record to the DVD R Disc for the capacity of 4 7GBytes The drive supports two write types of Disc at once recording and Incremental recording For more information of write types refer SFFC 8090 document 3 1 3 DVD RW Disc A DVD RW disc is specified by DVD Specifications for Re recordable Disc The drive can read and record to the DVD RW Disc for the capacity of 4 7GBytes The drive supports three write types of Disc at once recording Incremental recording and Restricted Overwrite recording For more information of write types refer SFFC INF 8090i document 3 1 4 DVD RAM Disc A DVD RAM disc is specified by DVD Specifications for Rewritable Disc The drive can read to the DVD RAM Disc for the capacity of 4 7GBytes 3 1 5 R Disc A R disc is specified by DVD R 4 7 Gbytes Basic Format Specifications version 1 0 or 1 1 3 1 6 R DL Disc A R DL disc is specified by DVD R 8 5 Gbytes Basic Format Specifications version 1 0 3 1 7 RW Disc RW disc is specified by DVD RW 4 7 Gbytes Basic Format Specifications version 1 1 3 1 8 CD ROM Disc Compact Disc Read Only Memory CD ROM is a standardized medium for r
41. mplemented in the drive Table 1 Packet Commands Operation Command Description SFFC 8090 4 This document 65 PERFORMANCE Command 13 6 lc B 6 11 6 12 613 6 14 6 15 6 17 43 W N N NIN N N N ele NI N ON o2 pat A o 4Ah A 4 oo Dh D 4 5Ah 4 A 5 C A5h D gt p 6 18 6 19 620 621 622 623 624 625 626 A 627 628 6 29 4 6 2 5 5 7 8 8 5 3 4 2 3 2 8 3 3 4 5 Eh 9h Sih h h h h h h h h h h h h h h h h h h SCAN Command B SEND OPC INFORMATION Command h 7 6h 1Bh Page 7 READ HEADER Command 13 27 6 30 631 632 633 634 635 13 34 6 37 13 35 6 38 639 4h h 0 h 1 h h 5 h 2 2 2 0 0 h A Bh D D F gt 3 6 40 6 41 6 42 6 43 6 44 6 45 1 5 5 5 5 h h BFh Bh A7h 5 4 4 4 3 5 B 4 4 4 2 1 B R8 Series Drive Command Reference Manual Version 0 90 PROE Operation Reference Command Description code 5 INF 8090i MMC 4 STOP PLAY SCAN Command 13 44 SYNCHRONIZE CACHE Command 13 45 TEST UNIT READY Command 13 46 WRITE AND VERIFY Command 2Eh 190 fos Page 8 R8 Series Drive Command Reference Manual Version 0 90 4 1 BLANK Command This command is valid for
42. n Function CD R RW Formatted Not valid CD RW DVD R RW Not valid Formatted DVD RW If a background format is in progress and de icing is not completed the format de icing operation will be RW stopped at some RW ECC block boundary No further writing will occur If there is no background format in progress then no operation shall occur and this will not be considered an error R R DL The drive closes the track associated with the track number in the CDB If the track is an invisible track no close operation is to be done If the track is an incomplete track the drive will write the PMA for the track If the incomplete track has the length of less than 4 seconds it will pad with all zero main data to the minimum length of 4 seconds prior to write the PMA No other padding shall be done CD R RW If the track is a partially recorded or empty reserved track the drive will pad until the end of the track In the case of an empty track the drive will write the track according to the Write Parameters Page If the Write Parameters Page is inconsistent with the PMA CHECK CONDITION status will be returned and SK ASC ASCQ will be set to ILLEGAL REQUEST ILLEGAL MODE FOR THIS TRACK For a partially recorded reserved track the drive will continue writing in the same mode as the data already recorded 001b Not valid Formatted Not valid CD RW If this is a Partially Recorded Reserved RZone or the Empty Reserved RZone the dri
43. nd needs to resend same command The minimum waiting time shows in the Table 40 If this value is used the size of empty area on the Writing Buffer becomes 128KBytes or more Table 40 Value of Minimum Waiting Time MEDIA WRITING SPEED Minimum waiting time msec i e 100 44 R8 Series Drive Command Reference Manual Version 0 90 5 Error Code Table 27 lists all error codes that may return from the drive Table 41 All Error Codes BLANK CHECK 00 06 1O PROCESS TERMINATED PLAY OPERATION ABORTED 04 01 LOGICAL UNIT IS IN PROCESS OF BECOMING READY 04 LOGICAL UNIT NOT READY MANUAL INTERVENTION REQUIRED LOGICAL UNIT NOT READY FORMAT IN PROGRESS 04 07 LOGICAL UNIT NOT READY OPERATION IN PROGRESS LOGICAL UNIT READY LONG WRITE PROGRESS 00 LOGICAL UNIT COMMUNICATION FAILURE 01 LOGICAL UNIT COMMUNICATION TIMEOUT SPINDLE SERVO FAILURE CIRC UNRECOVERED ERROR DE COMPRESSION CRC ERROR POSITIONING ERROR DETECTED BY READ OF MEDIUM PARAMETER LIST LENGTH ERROR SYNCHRONOUS DATA TRANSFER ERROR INVALID COMMAND OPERATION CODE LOGICAL BLOCK ADDRESS OUT OF RANGE INVALID ADDRESS FOR WRITE INVALID FIELD IN CDB INVALID FIELD IN PARAMETER LIST PERSISTENT WRITE PROTECT NOT READY TO READY CHANGE MEDIUM MAY HAVE CHANGED POWER ON RESET OR BUS DEVICE RESET OCCURRED M
44. ned in a legacy specification SCSI 2 4 25 SEND DVD STRUCTURE Command The Format field indicates the type of information that is sent to the device Table 31 Format Code definitions for SEND DVD STRUCTURE Command Format Code 04h User Specific Data Send User Specific Data to the RMD cache OFh Send data to the RMD cache 20h LO Data Zone Capacity Send LO data zone capacity Write Protection Send PWP status 4 26 SET CD SPEED Command The drive can not specify the reading speed by any Packet command The setting of Logical Unit Read Speed field is ignored The reading speed is determined by the drive This command changes the writing speed for CD R RW media It does not effect to the writing speed for DVD R RW and R RW media The available writing speed may be restricted by the drive when the characteristic of media is not suitable for the speed Table 32 Available Writing speed for each media Available Writing Speed jor ima 10x CLV 4x CLV CD RWO 49 2 0 24x ZCLV 20x ZCLV 16x CLV CD RW Ultra Speed 10x CLV Table 33 Parameters to set Writing speed for CD R RW Logical Unit Writing CD R Writing CD RW Writing DVD R RW and R RW Speed Speed Speed Writing Speed 0000h 06E3h 4x CLV 4x CLV 06E4h OBO6h 10x CLV 10x CLV 0207h 16x CLV 1015 Remains previous setting ODC8h 1089h 20x ZCLV 108Ah 160Ch 24x ZCLV 160Dh FFFFh 32x ZCLV 40 R8 Series D
45. ondition status LOGICAL UNIT NOT READY FORMAT IN PROGRESS 2 04 04 If the drive returns Good status for these command format operation has completed In response to the REQUEST SENSE command including after the Check Condition status described above the drive will return a SK ASC ASCQ values set to NOT READY LOGICAL UNIT NOT READY FORMAT IN PROGRESS with the sense key specific bytes set for progress indication The SKSV will be set to one and the Progress Indication field will contain 16 bit unsigned value such that Progress Indication 65 536 X 100 approximates the percentage of completion of the operation Once the operation is completed the SKSV will be cleared to zero Page 14 R8 Series Drive Command Reference Manual Version 0 90 4 3 1 1 1 On CD RW media The media is formatted using Write Parameter Mode Page information Some parameters in the Write Parameter Mode Page shall be set as follows Test Write 0 Write Type Oh FP 1 Track Mode 01x1b Data Block Type 8h or Ah Session Format 00h or 20h Packet Size 20h This format operation is always available regardless of the media condition 4 3 1 1 2 On DVD RW media The media is inserted in the drive the area from the beginning of the RMA to the end of the Lead out will be recorded There is only one bordered area on the medium and the number of RZone is one after this operation The Test Write bit in the Write Parameters Mode Page shall be set to zero Thi
46. or CD R RW for DVD R RW Packet Incremental SR Se Se The default value of the Test Write bit is 0 and the default value of the Write Type field is Oh When FP bit is set to one for CD R RW media the Packet Size field must be set to 32 Because the drive supports 64K Fixed Packet Writing only The default value of the FP bit is 0 The Copy bit is not supported and setting of this bit is ignored The drive supports following Data Block Type for CD R RW media Table 26 Data Block Type Field 25 Rawdta ves 8 248 Mode USOMEC 10149 9 2 Mode 2USOMEC 10149 Note Parameter setting The drive supports writing of DVD and CD Each media needs different value of Link Size field in Write Parameters page Current value of parameter can not change by mounted media automatically But Default value of Link Size field is changed by mounted media If DVD media is mounted Link Size field of default value in Write Parameter page is set to 10h If CD media is mounted it is set to 07h It recommends following step to setting the Write Parameters page 1 Get default value of Write Parameters by using MODE SELECT command Page Control PC field 10b 2 Modify the necessary field on above parameter 3 Send the modified parameter by using MODE SELECT command Page 34 R8 Series Drive Command Reference Manual Version 0 90 4 12 2 6 C DVD Capabilities and Mechanical Status Pag
47. ported 1 LSB 36 59 Logical Unit Write Speed Performance Descriptors 2 7 Reserved 00h Reserved Rotation Control 8 000000b 00b Write Speed Supported 8 The Maximum Read Speed Supported field is set to 160Ch for CD media and is set to 1AA2h for DVD media It does not reflect the maximum read speed for each medium type and format If no disc is mounted in the drive the field is set to the same value as DVD The Current Read Speed filed is set to 160Ch for CD media and is set to 1AA2h for DVD media It does not reflect the actual read speed If no disc is mounted in the drive the field is set to the same value as DVD The Maximum Write Speed Supported field is set to the same value of the Write Speed Descriptor 1 data which is returned for the GET PERFORMANCE command The Current Write Speed filed is set to the same value of the Write Performance data which is returned for the GET PERFORMANCE command The Number of Logical Unit Write Speed Performance Descriptor Tables and The Logical Unit Write Speed Performance Descriptors 8 are set to the suitable values by using the same algorism as the GET PERFORMANCE command 4 13 PLAY CD Command This command is defined in a legacy specification MMC2 Revision 102 4 14 READ 10 READ 12 Command The RelAdr bit is not supported and must set to 0 If the Streaming bit in the CDB of the READ 12 command is set to one the FUA bit shall be set to zero The setting
48. rive Command Reference Manual Version 0 90 4 27 SET STREAMING Command The Drive can not specify the reading speed by any Packet command The reading speed may be automatically reduced by the drive in order to retry to read a block which has not been corrected errors Table 34 Available Reading speed for each media CD DA R RW play audio 9 3xCAV 4xCLV PO CD ROM R RW read mode2form2 93x CAV 4xCLV CD DA ROMIR other operations 40XCAV 4xCLV PO CD RW other operation 32CAV 4k amp CLV After writing readi db d CD ROM R RW 8cm with adapter 9 3x CAV 4x CLV becomes sanie Hed as DEDE _ _ speed DVD ROM Single Layer 16x CAV 1x CLV DVD ROM Dual Layer 12x CAV Ix CLV E DVD R 12x CAV Ix CLV d writing reading speed becomes same speed as writing speed DVD RW 8x CAV 1x CLV After writing reading speed becomes same speed as p TELLS speed DVD RAM 2x CAV 12x 24x CLV aa writing reading speed becomes same speed as writing speed 8x CAV 2 4x CLV After writing reading speed becomes same speed as writing speed 8x CAV 2 4x CLV After writing reading speed becomes same speed as writing speed DVD ROM R RW 8cm with adapter 34x CAV Ix CLV After writing reading speed becomes same speed as writing speed The drive can specify the writing speed by the SET STREAMING Command The performance setting is persistent and remains until a new descriptor is sent so
49. s format operation is available on any recording mode and any state of a bordered area 4 3 1 2 Format Type 10 C DVD RW Full Format Formatting to create a Session Border on C DVD RW media is specified If the Immed function is set to zero the drive will return the status after the format operation has completed If the Immed bit is set to one the drive will return the status as soon as the command descriptor block has been validated and the entire Format Descriptor has been transferred The READ DISC INFORMATION Command the READ TRACK RZONE INFORMATION Command and the TEST UNIT READY Command is used to detect completion of the format operation While format operation is performed by the FORMAT UNIT Command that the Immed function is set to one the drive terminates these commands with the Check Condition status LOGICAL UNIT NOT READY FORMAT IN PROGRESS 2 04 04 If the drive returns Good status for these command format operation has completed In response to the REQUEST SENSE command including after the Check Condition status described above the drive will return a SK ASC ASCQ values set to NOT READY LOGICAL UNIT NOT READY FORMAT IN PROGRESS with the sense key specific bytes set for progress indication The SKSV will be set to one and the Progress Indication field will contain 16 bit unsigned value such that Progress Indication 65 536 X 100 approximates the percentage of completion of the operation Once the operation is completed
50. t bit of the Feature List for R RW media is set as Table 14 Feature List for R RW Media The State No is described in the Table 8 Media states Table 14 Feature List for R RW Media Race ees 2122222 Feature Name 1 2 3 4 Removable Mein 0004h WrteProet pp 001Dh Multi Re 1 1010 E OE 001Fh DVD Read ee 8 0020h Random Writable sd Random Writable ES cue e E 00231 Formattable 00268 Restricted Overwrite 0 00298 Software Defect Management 01010 0 002Ah DvDeRW 002Bh DVD R_ 002Ch Rigid Restricted Overwrite 0 0 ofo 0 o o o o o 002Dh CD Track at Once 00 o 002Eh CD Mastering fofofo E 002Fh DVD R RW Write oj ojo ojo ojo o o 003Bh DVD RDoubleLayer 01008 PowerManagement Tt Tt Tt fat ft att fafa 1 CD Aie 10404010404 048181000 01048 Microcode Upgrade 11 0 0 010 Eomae E inier e x epe pm oih pvD CSS o ojojo oJo ojojojo o 0107h Real Time Steaming 0 0 1 111 0 11 1 0 111 O10Ah Disc Control Block 0 write operation if Read
51. table ofjo ojo o o 1 1 1 1 1 00261 Restricted Overwrite 00291 Software Defect Management 0 0 1 1 2 002 Rigid Restricted Overwrite 10 0 0020 CD Track at Once 002 CD Mastering ssf JO 002Fh DVD R RWWrite 0 0 11 0 0 0 1 0 01010 003Bh DVD RDoubleLayer D 04040401000 01048 Microcode 0104h Microcode Upgrade sd 1 01064 DVD CSS 0107h Real Time Streaming sd Real Time Streaming 1 ate ical oi 1 beh 010 Disc Control Block 010Bh DvDCPRM_ d J d ra d a In write operation if Read command returns the Check Condition the current bit is set to zero b In write operation it keeps previous setting c If CSS encrypted disc is existing the current bit is set to one d If the CPRM exists on the disc the current bit is set to one if the CPRM does not exist on the disc the current bit is set to zero Page 24 R8 Series Drive Command Reference Manual Version 0 90 4 4 4 3 Current bit of the Feature List for R RW Media The Curren
52. the SKSV will be cleared to zero 4 3 1 2 1 On CD RW media The created Session will become the only Session on the medium The Number of Blocks field specifies the number of addressable blocks for the new Session and the Type Dependent Parameter field specifies the Fixed Packet Size 32 The Number of Blocks field may be adjusted to a value less than or equal to the values reported by the READ FORMAT CAPACITIES Command The drive will round the Number of Blocks up to be an integral multiple of the packet size Some parameters in the Write Parameter Mode Page shall be set as follows Test Write 0 Data Block Type 8h or Ah Session Format 00h or 20h After the FORMAT UNIT command is received by the drive some parameters in the Write Parameter Mode Page will be modified as follows Write Type Oh FP 1 Track Mode 01x1b Packet Size 20h This format operation is always available regardless of the media condition 4 3 1 2 2 On DVD RW media The created Border will become the only Border on the medium The Number of Blocks field specifies the number of addressable blocks for the new Border and the Type Dependent Parameter field specifies the ECC block size 16 The Number of Blocks field may be adjusted to a value less than or equal to the values reported by the READ FORMAT CAPACITIES Command The drive will round the Number of Blocks up to be an integral multiple of the ECC block size The Test Write bit in the Write Parameters Mode P
53. tion Block is set 10105 A background format is in progress A format has been started restarted and is not yet completed When BG format operation is completed it is set to 11b Formatting has completed A fully formatted RW disc is currently mounted However if the BG format operation is interrupted it may be set to 01b A background format was started but is not currently running and is not complete 4 29 VERIFY 10 Command The RelAdr bit BytChk bit and DPO bit are not supported and must be set to zero Page 43 R8 Series Drive Command Reference Manual Version 0 90 4 30 WRITE 10 WRITE 12 Command The RelAdr bit is not supported and must be set to zero If the Streaming bit in the CDB of the WRITE 12 command is set to one the FUA bit shall be set to zero The setting of the Streaming bit is no effect on the operation When a formatted CD RW disc or a formatted DVD RW disc or RW disc is mounted if the WRITE 10 WRITE 12 Command that cause the writing buffer over run condition is received the execution of these commands is deferred until the blank area of the buffer grows to be able to receive the data When the other disc is mounted if the WRITE 10 WRITE 12 Command that cause the writing buffer over run condition is received these command is terminated with Check Condition status LOGICAL UNIT NOT READY LONG WRITE IN PROGRESS 2 04 08 If the Host receives this error code the Host waits several time a
54. tted Disc 25 DVD ROM _ Complete 0 ei 62 Appendable One or more Session closed Disc Existing Complete Session Appendable or more Session closed Disc Appendable Complete Not appendable Disc Layer Existing Complete Session Page 19 R8 Series Drive Command Reference Manual Version 0 90 4 4 3 Current Profile of the Feature Header and Current bit of the Profile List The Current Profile of the Feature Header and the Current bit of the Profile List is set as following The Current Profile and Current bit of Profile List is morphed by media state 4 4 3 1 Current Profile and Current bit for No Media and CD Media The following table indicates the Current Profile of the Feature Header and the Current bit of the Profile List that no media or CD media is mounted Table 9 Current Profile and Current bit for No Media and CD Media Current bit of the Profile State Current CP CD R CD DVD DVD DVD DVD DVD DVD DVD ROM RW ROM R RW RW RW R R descriptions No Profile S W R O S W DL 0008 0009 000A 0010 0011 0013 0014 001A 001B 002B No Profile that the current bit is set to one CD ROM Profile is current 2 ooosh 1 0 a 1 to indicate the read only OD R Profile is is current to CD R Profile is is current to CD ROM Profile is current to indicate the readable CD R Profile is current to indicate the writable CD ROM Profile is current ES UR ESE
55. us difference between the start of the temporary lead out and the end of the temporary lead out will approximate 1 mm The data zone will be expanded to ensure that the total recorded area reaches at least a radius of 35 mm RW The drive closes the last session If not all Fragments in the last Session are closed the Drive will terminate this command with CHECK CONDITION Status and sense data shall be set to ILLEGAL REQUEST SESSION FIXATION ERROR INCOMPLETE TRACK IN SESSION TR If upon completion of the closure less than 65 ECC blocks would remain the drive will finalize the disc If the session being closed is session number 154 when the close session is requested the drive will finalize the disc W The drive closes the last session If not all Fragments in the last Session are closed the Drive will terminate this command with CHECK CONDITION Status and sense data shall be set to ILLEGAL REQUEST SESSION FIXATION ERROR INCOMPLETE TRACK IN SESSION If the LBA of the last ECC block of the session closure is greater than or equal to the LBA of the last R DL ECC block on LO of R DL media then both middle zones will be recorded If upon completion of the closure less than 65 ECC blocks would remain the drive will finalize the disc If the session being closed is session number 127 when the close session is requested the drive will finalize the disc If LO Data Zone Capacity has been changed from default value and the session being
56. ve will pad the DVD R RW RZone with 00h bytes If the RZone status is Invisible no close operation is to be done In the case of an Incomplete RZone no padding is to be done and cached RMD will be written into the RMA Formatted Not valid DVD RW eee The drive closes the Fragment associated with the track number in the CDB If the Fragment being closed is reserved and blank or partially written the drive will pad the Fragment to its defined length User data areas in all pad sectors will be zero filled If the Fragment being closed is an incomplete Fragment and the incomplete Fragment is not blank then R R DL anew DCB will be appended into the Session Identification Zone defining the existence of the Fragment If the Fragment being closed is an incomplete Fragment and the incomplete Fragment is blank then the command will be terminated with GOOD status and sense data will be set to NO SENSE NO ADDITIONALINFORMATION Page 10 R8 Series Drive Command Reference Manual Version 0 90 Close Media Description Function The drive closes the last session If not all tracks in the last Session are closed the drive terminates the command with CHECK CD R RW CONDITION status and sets SK ASC ASCQ values to ILLEGAL REQUEST SESSION FIXATION ERROR INCOMPLETE TRACK IN SESSION Behavior of the closing operation is dependent on the Multi Session field in the Write Parameters Page 05h If the last session is empty the command
57. will be terminated with GOOD status Formatted Not valid CD RW The drive closes the last border If all RZones in the last Border are not complete the drive generates CHECK CONDITION Status 5 72 03 SESSION FIXATION ERROR INCOMPLETE TRACK IN SESSION If one or more empty or partially recorded reserved RZones exist in the incomplete Border the drive DVD R RW generates CHECK CONDITION Status 5 72 04 EMPTY OR PARTIALLY WRITTEN RESERVED TRACK Behavior of the closing operation is dependent on the Multisession Border field in the Write Parameters Mode Page 05h Closing an empty Border does not produce an error and a write to the media will not occur When the last bordered area is in the intermediate state Lead in and or Border out are recorded to make Formatted the bordered area complete state If the bordered area is to be closed that is the first one Lead in and DVD RW Border out will be recorded If the bordered area is to be closed that is second or later one only the Border out will be recorded If a background format is in progress the format operation will be stopped and the disc will be structured for removal according to the DVD RW 4 7 Gbytes Basic Format Specifications for the 010b specific purpose of providing DVD RO compatibility To be concrete a partial lead in will be written a temporary lead out will be appended and all unrecorded gaps between lead in and lead out will be format written The radi
Download Pdf Manuals
Related Search