Hotpoint E320SKIX hob
Contents
1. 1 0145 2 180 27 FE Fig 3 Fig 4 HOSRR F3 x 1 5 es T 0588 F4 x 0 75 1 400V 2N V 1 010 170 Fig 5 ELECTRIC PLATES SUPPLY TYPE w REGULATION e QUICK 145 1500 CLOCKWISE AND ANTICLOCKWISE ROTATION e QUICK Y 180 2000 230 V e red point Instructions for the installer Installation These instructions are turned to the skilled installer as a guide toinstallation regulationand maintenance in compliance with the lawsand the rules in force Any of these operationsmust always be carriedout when the appliancehas been disconnected from the electric system Positioning Fig 4 The apparatus isprovided to be built in awork top as shown in thespecial figure Present the sealing agentalong all the perimeter Electrical connection Fig 5 Before carrying out theelectrical connection be sure that the characteristics of the system are such as tosatisfy what indicated onthe part number plateapplied to the bottom ofthe work top that the system is provided with the effective ground in compliance with the rules and the provisions of law in force The ground is binding according to the law In case the apparatus isntprovided with cable and or with relative plugmake use of material suitable for the absorption indicated inthe part number plate andfor the workingtemperature The cableshould reach in no point atemperature higher 50 Cthan of the room temperat2. inaccuracies contained in this pamphlet due to printing or copying errors We reserve the right to make on our own products those changes to be considered necessary or useful without jeopardizing the essential characteristics Notes fl Hotpoint Indesit Company UK Limited Morley Way Peterborough PE2 9JB England www hotpoint co uk Cod 1 007 23 0
3. Electrical Cooking Hob fl Hotpoint English E320SKIX E Hotpoint Index Instructions for use Installation 4 Use 4 Maintenance 4 Instructions for the installater Installation 6 Positioning 6 Electrical connection 6 Assistance 7 THIS APPLIANCE IS CONCEIVED FOR DOMESTIC USE ONLY THE MANUFACTURER SHALL NOT IN ANY WAY BE HELD RESPONSIBLE FOR WHATEVER INJURIES OR DAMAGES ARE CAUSED BY INCORRECT INSTALLATION OR BY UNSUITABLE WRONG OR ABSURD USE Dear customer We thank you and con gratulate you on your choice This new carefully de signed product manu factured withthe highestquality materials has been carefully tested to satisfy all your cooking demands We would therefore request you to read and follow these easy instructions which will allow you to obtain ex cellent results right from the start May we wish you all the very best with your modern appliance THE MANUFACTURER Instructions for use Installation USE OF ELECTRICAL PLATES quick normal intensity of heat All operations relative to installation electric connection should be carried out by skilled personnel in conformity with the rules in force As for the specific instructions see Weak part pertaining to installer Gentle Slow Use Medium Electric plates Fig 1 2 3 Strong Rotate the knob to the position correspondent to the needs of cooking taking into consideration that to a higher number a higher heat supply corre
4. sponds see table use of electric plates Quick and normal plates clockwise and anticlockwise rotation with 7 fixed position 0 6 The pilot lamp on indicates when plate is connected Some types of pilot lights will maintain some slight luminescence even after disconnection That is quite normal Bright N B When one makes use of electric plates we advise receptacles with flat bottom having same diameter or lightly higher than that of the plate avoid overflows of liquid therefore when boiling has happened or in any case when liquid is heated reduce the heat supply dontleave the electrical plates on without receptacles on the top or with void pots and pans at the end of cooking take again the knob to position 0 4 Maintemace 3 Before every operation its necessary to disconnect the 2 apparatus To obtain a higher life of the apparatus concerned it s indispensable to carry out at regular intervals a carefully Fig 2 general cleaning bearing in mind the following the s s and or enameled parts should be cleaned by means of suitable not abrasive or corrosive products available on the market Avoid cloride base products bleach etc avoid leaving on the top acid or alkaline substances vinegar salt lemon juice etc the electric plates have to be cleaned by means of a wet rag and lightly oiled with lubricant when they are still tepid DO NOT USE STEAM CLEANERS E Hotpoint
5. ure If connecting directly to the mains power supply fit a multi poles witch of a suitable size for the rated capacity with a clearance distance which completely disconnects the power line under over voltage category Ill conditions consistently with the rules of installation the yellow green earth wire must not be interruptea The plug on the omnipolarswitch should be easilyreachable with apparatusinstalled N B Themanufacturer declines allresponsibilityincase the above and the usual safety rules aren trespected To avoid all risk if the powercable becomes damaged it mustonly be replaced bythe manufacturer byan authorised service centre or by aqualified electrician Assistance Hotpoint Before contacting After Sales Service See if you can solve the problem yourself 2 Switch the appliance on again to see if the problem has been solved if it has not disconnect the appliance from the power supply and wait for about an hour before switching on again 3 If the problem persists after this course of action contact After Sales Service Specify e the nature of the fault e the model e the service number the number after the word SERVICE on the rating plate on the rear of the appliance e your full address e your telephone number and area code Never call on unauthorized technicians and always refuse to purchase non original spare parts The manufacturer declines all responsibility for possible
Download Pdf Manuals
Related Search