CDA WC431 dishwasher
Contents
1. Contact CDA Customer Care 22 Possible Cause Check the plug fuse and circuit breakers of the mains supply The water tap is turned off The dishwasher door is not fully closed The water inlet filter or the machine filters are blocked the end of the programme The filters are blocked Power failure Water inlet failure Programme is on standby Poor loading of dishes hinders wash performance Insufficient detergent added Wash performance is of a low standard Inappropriate wash programme selected Spray arm is blocked Filters clogged or incorrectly fitted Water drain pump is blocked Insufficient detergent added Rinse aid setting is too low Insufficient disnwasher salt added Water softener setting is too low Salt compartment cap may not be completely closed A programme without a drying stage was selected Rinse aid setting is too low Dishes unloaded too soon allow time for drying Different sets of cutlery should be kept separate Too much salt water softener setting is too high Salt compartment cap not completely closed Poor appliance earth check mains electrical Supply The door is not opening or closing Door tension not correctly adjusted on the properly d cor door The programme will not start The dishwasher stops in the middle of a programme White stains on the dishes The dishes are not completely dry at the end of a programme There are rust stains on the dishes 23 Electrical Information Warning Thi2. results obtained can vary depending on the conditions of the dishwasher s use and environment mains supply voltage water pressure water input temperature and environment temperature Laboratory measured value in accordance with European standard EN50242 19 Care and Maintenance Before beginning any care or maintenance you should always disconnect the appliance from the electricity supply and also turn off the water supply Fascia Wipe the fascia clean using just a damp cloth rinsed in a mild liquid detergent solution and well wrung out Door Seals Wipe the dishwasher door seals regularly with a damp cloth to remove any residues Filters You should clean the filters at least once a month 1 Remove the lower basket 2 Turn the microfilter anticlockwise and then lift it out figure 16 3 Remove the coarse filter from the microfilter figure 17 4 Remove the base filter from the dishwasher compartment fi gure 18 You should clean and rinse the filters thoroughly before replacing all the sections in 20 reverse order to that above The microfilter should lock into place once it is secure figure 19 Please note Never run a programme without the filters in place Incorrect fitting of the filters may reduce wash performance and potentially damage your appliance Spray Arms You should clean the spray arms at least once a month 1 Remove the lower basket 2 Pull the lower spray arm upwards
3. cable the appliance may require removing for servicing N B Ensure that the plug socket is situated in an easily accessible place 29 Installation Do not install this appliance if it is damaged in any way Installing a damaged appliance may invalidate the warranty The water supply tap should be located in an adjacent cupboard So that it can be accessed after installation Ensure the appliance is level by adjusting the feet as necessary The dishwasher is equipped with an adjustable rear foot that can be raised or lowered by means of an adjustment screw located in the centre of the kick plate Only use the water inlet supplied with the appliance If the water pressure is above 10 bar a pressure relief valve should be used After connecting the water supply check to ensure there are no leaks The water outlet can either be Eo o MES connected to a water drain or to a sink outlet spigot his connection should be at a minimum of 50 cm and a maximum of 110 cm from the floor The drain hose should be no longer than 4m in length to ensure good performance from the dishwasher To prevent syphoning ensure fig 22 26 that the water outlet is not pushed too far into the waste Standpipe The lowest part of the water outlet should be level with the bottom basket of the dishwasher e When connecting to the sink ensure that the waste pipe runs higher than the level of the sink bowl to prevent syphonin
4. open the compartment Add the required amount of detergent The main detergent compartment b figure 2 has lines to allow for specific amounts of detergent These are marked at either 15 cm or 25 cm to be used depending on how dirty the dishes are If your dishes are in need of an intensive wash then add 5 cm of detergent into the prewash section of the compartment a figure 1 Then close the detergent compartment lid until the latch locks 10 Please note You should only use detergents designed specifically for use in dishwashers Combination detergents e g 3 in 1 tablets must not be used in any quick wash or half load programme If using dishwasher tablets always use the detergent compartment do not put them in the main body of the dishwasher or in the cutlery basket The solubility of dishwasher tablets can vary depending on the temperature and duration of the programme As a result it is recommended that powder detergents should be used in the shorter programmes to allow better performance CDA recommends the use of separate detergent rinse aid and dishwasher salt rather than combination tablets as separates achieve better wash performance If you do use combination detergents add salt and rinse aid to the dishwasher and then adjust the water hardness setting and rinse aid setting to the minimum When you then use separate detergents again you should fill the salt and rinse aid compartments adjust th
5. to remove it 3 Toremove the upper spray arm first remove the nut on the upper spray arm by turning it figure 9 4 You should clean and rinse the spray arms thoroughly before replacing them Ensure that the upper spray arm nut is securely tightened when refitting the upper spray arm To deal with an accumulation of dirt oil or limescale in the dishwasher run an intensive programme with detergent when the dishwasher is empty Alternatively there are specialist dishwasher cleaners available that can be used 21 Failure Codes and Troubleshooting The programme indicators also serve as a diagnostic display to help in the event of a problem with the appliance Error Description Turn off dishwasher and disconnect water supply Contact CDA Customer Care Drain hose is blocked The filters in the machine may be blocked Restart the dishwasher and cancel the programme If the error continues contact CDA Customer Care Alarm is active against FI water flow Waste water in the machine cannot be discharged Make sure the water tap is fully open Close the water tap separate the water inlet Inadequate water hose from the tap and clean the filter supply Restart the dishwasher If the error continues contact CDA Customer Care Overheating error F7 temperature in the Contact CDA Customer Care machine is too high Contact CDA Customer Care EN apay Bene Poo Contact CDA Customer Care FE Faulty electronic card
6. Run a hot programme without any dishes in the dishwasher Control Panel O 9h OC end bak ibad delay timer O 3h salt ag h C rinse aid programme Power Button 1 To switch the dishwasher on or off press the power button 1 When you switch on the dishwasher the end of programme light will illuminate and two dashes will appear on the display Programme Display 2 The programme display shows the selected programme and the remaining time to run If there is a fault on the dishwasher the fault code will show on the display Programme Selection Button 3 To select a programme press the programme selection button 3 The dishwasher will store in its memory the last programme used Half Load Button 4 and Indicator Light The dishwasher is equipped with a half load function that allows for small numbers of dishes to be washed spread between both baskets This reduces the amount of water and electricity used e o use this function press the half load button 4 the indicator light shows to indicate that this function is selected If you have selected the half load function for a programme this function will automatically be selected the next time the dishwasher is used To cancel the selection of this function press the specific half load button 4 until the indicator light goes out Delay Timer Button 5 The dishwasher is equipped with a variable timer of 3 6 or 9 hours to delay the star
7. Ss CIDIA WC431 Slimline Integrated Dishwasher Manual for Installation Use and Maintenance Customer Care Department The WO Vade Har xdi oad DM W To Te TD Nottinghamshire NG13 9HY T 01949 862 012 F 01949 862 003 E ercare amp cda e www cda eu Contents Eo NS MR ere arty ee E E T E 2 Anales ats lg TERT 3 POORA CNO a E EA 4 Icone NaON enaa EONO 6 BETOR E U c TT Tm 6 COR alle TRENT 7 BICIS QN NU TT NNUS 10 cm D E 12 SONET Gy GS ESI oat gael ater cee earthen edie eut SN Leu Ls 13 Mak icu SEN EE E E 15 Dishwasher BD ASK EIS vicinvineseesictacumcichianinsetsiavaveseuniecancarciehiamanciovetensbisoncices 16 Slehidard Loading anmd Fesriald usaumd e tei 18 FOC et ei BHI UN O RERO TL 19 Careand AVI OSC E sereine tbe nated at tes OAG 20 Failure Codes and Troubleshooting datasets tudin cache ede napi eee 22 mises ge CIS ADR 24 HIRI UN CVG Oe eee EMT 26 Fitting the Integrated Appliance DOO sock ad traced trot dvo 2 Important The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or installation of this product Please note that CDA reserve the right to invalidate the guarantee Supplied with this product following incorrect installation or misuse of the appliance or use in a commercial environment This appliance is not designed to be used by people including children with reduced physical sensori
8. al or mental capacity or who lack experience or knowledge about it unless they have had Supervision or instructions on how to use the appliance by someone who is responsible for their safety Under no circumstances should any external covers be removed for servicing or maintenance except by suitably qualified personnel Appliance information Please enter the details on the appliance rating plate below for reference to assist CDA Customer Care in the event of a fault with your appliance and to register your appliance for guarantee purposes This appliance has been designed for domestic use only Commercial use will invalidate the warranty CE Declarations of Conformity This appliance has been designed constructed and marketed in compliance with safety requirements of EEC Directives 2004 A08 EC 2006 95 EC IEC436 DIN44990 amp EN 50242 Availability of this manual in an alternative format A soft copy of this manual is available for download from www cda eu IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH EC DIRECTIVE 2002 96 EC At the end of its working life the product must be taken to a special local authority waste collection centre or to a dealer providing appliance recycling services Disposing of a household appliance separately avoids possible negative consequences for the environment and health It also enables the constituent materials to be recovered saving both energy and resou
9. ans etc on lower basket When you move the top basket to lower position you can place and wash large plates on the top basket The basket height is adjusted by using the alternative wheel sets on the tracks Swing open the basket retainers fig 9 Slide the basket forward off the rails Re insert the other set of wheels into the rails Swing the basket retainers closed fig 9 BONO The images below are designed as guidance as to best practice for loading the dishwasher Lower basket 1234588 7 E Standard Loading and Test Data Capacity e Upper and lower baskets 10 place settings e he upper basket should be adjusted to high position e Cups should be placed on to the dish rack pins Detergent Rinse Aid e 5 20 cm in accordance with EN50242 DIN 44990 IEC 436 international norms Rinse aid dosage adjustment 4 Programme Test e Eco 50 C in accordance with EN 50242 international norms Programme Listing ne Intensive Intensive Express ane Quick Prewash LOGIE 65 C P2 OBNEIPS 5C 40 C P5 P6 gp wee of Soil Detergent Required E E 70 C Wash 65 C Wash 65 C Wash 50 C Wash 40 C Wash Cold Rinse Cold Rinse Cold Rinse Cold Rinse Cold Rinse 3 oe ee OAM Duration min Electricity Consumption kW hour Water Consumption litre The values and times provided above have been obtained under laboratory conditions according to relevant standards Actual
10. e water hardness setting to the maximum and run an empty wash then adjust the water hardness setting and the rinse aid setting to the appropriate level 11 Salt To ensure the best efficiency the dishwasher needs soft water Hard water means that lime residues remain on the dishes and the interior of the dishwasher affecting performance The softener system is designed to remove the ions that make the water hard to provide the best quality wash performance This is achieved by using dishwasher salt To Add Dishwasher Salt Follow the Steps Below 1 Remove the lower dishwasher basket and then unscrew the Salt compartment cap as shown in figure 3 2 Fill the compartment with dishwasher salt do not use table salt carefully to prevent unnecessary spillage figure 4 Before first use you should fill the compartment with 1kg of dishwasher salt and then fill up the salt compartment with water up to the brim of the compartment as shown in figure 4 3 Replace the cap and the lower basket When the salt warning light on the control panel illuminates you should refill the salt compartment with salt only do not add water to the salt compartment after the first use Important You should run a prewash programme immediately after adding dishwasher salt to prevent any damage to the dishwasher systems Only fill the salt compartment with water on first use 12 Softener Adjustment The efficiency of your dishwash
11. er depends on the softness of the tap water To ensure best efficiency the dishwasher is equipped with a system that reduces the hardness in the mains water supply The efficiency will increase when the system is correctly set To find out the water hardness level of your water supply you can use the test strip Supplied or alternatively contact your local water board Open the testing strip figure 5 Run water through the tap for one minute e Hold the testing strip in water for one second e Remove from the water and Shake the test strip to remove excess water e Wait for one minute e Check the number of marks on the strip to see the level of water hardness If the hardness of the water you use is above 63 dE or if you are using well water you are recommended to contact 1 minute your local water board to confirm the Level CETTIIIIITI No tine water hardness level and to use filter and ym o Hib Sag water refinement devices Level COCCI Mesum ime contort Wvs CCINIONCNCNO Une conten Lovel 6 CNIONIONEONI NL High ne conten Please note The level of water Er hardness is preset to level 3 19 1 Press and hold down the programme selection button 2 Press the Power button to switch on the dishwasher 3 Keep the programme selection button pressed until 8 shows on the display and then disappears 4 After the 8 disappears the machine displays the last water hardness setting entered 5 To adjust the
12. g Fitting the Integrated Appliance Door Where non standard integrated appliance doors are supplied additional fitting instructions are required to ensure compatibility with this product The machine is supplied with a fitting template and these instructions should be followed as normal However the fitting template needs to be located lower down the fascia door this is shown below The amount of offset Y depends on the height of the fascia door and can be calculated as X 23mm For example if you have a 31mm tall fascia door and are fitting a door to your dishwasher then Y 31 23 8mm de 57 T A 6 o a x Ensure that the hinge tensioners are adjusted to balance the weight of the door 2 CIDA Customer Care Department The CDA Group Ltd Harby Road Langar Nottinghamshire NG13 9HY T 01949 862 012 F 01949 862 003 E service cda eu W www cda eu
13. level press the programme selection button 3 until the required level is shown on the display as listed in the Table of Water Hardness below 6 To store the selected water hardness level press the power button Water Hardness Level British Hardness dE Display Shows Rinse Aid To Fill the Rinse Aid Compartment 1 Open the rinse aid compartment by turning and removing the cap as shown in figure 6 2 Fill the rinse aid compartment until the rinse aid indicator goes dark as shown in figure 7 where a indicates the compartment is empty and b indicates the compartment is full 3 Replace the cap ensuring the markers on the cap line up with the compartment prior to screwing the cap back in place Rinse Aid Adjustment The level of rinse aid use is preset to 3 You can adjust the level of rinse aid use by adjusting as shown in figure 8 If water stains form on the dishes after a wash the level should be increased If blue stains which can be wiped away are left on the dishes after a wash the level should be decreased Please note Rinse aid ensures better quality wash results and increased drying performance 15 Always refill the rinse aid when the rinse aid indicator light on the control panel is illuminated Dishwasher Baskets Top Basket Height Adjustment The top basket of your machine is Supplied in the upper position When it is in this position you can place big items such as p
14. rces As a reminder of the need to dispose of household appliances separately the product is marked with a crossed out wheeled dustbin Important Notes e Read the instructions prior to installation and use of the appliance e Do not lean or climb on the open dishwasher door to prevent damage e Close the dishwasher door after use to prevent accidents e Use only detergents salt and rinse aid specifically designed for dishwashers e Do not put solvents in the dishwasher detergent compartment to prevent risk of explosion e Only put dishwasher safe items into the dishwasher If in doubt check with the manufacturer of the items e lake care when loading the dishwasher to observe the recommendations for best loading practice and also to ensure that sharp objects such as knives are placed blade down to prevent accidents 4 Do not open the dishwasher door when a programme is running If it is necessary to do so then open it only slightly to allow the dishwasher to pause the programme and prevent any water spilling out Remember that the water in the dishwasher can be very hot when the programme is running When the dishwasher is not in use we recommend that you turn off the water supply at the supply tap and disconnect the main supply If you are leaving the dishwasher for an extended period you should leave the door slightly open to prevent the formation of unpleasant smells The plastic housing on the water inlet pipe contain
15. s an electrically operated valve The wires that connect to this valve are inside the inlet hose Do not cut through the inlet hose and do not put the plastic housing in water Children could get locked inside the appliance Therefore when disposing of an old appliance cut off the plug and set aside and damage the door lock so that the door can no longer be closed This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved Children shall not play with the appliance Cleaning and user maintenance shall not be made by children without supervision Recommendations To reduce energy and water consumption remove all dirt residues from the dishes prior to loading the dishwasher Only run the dishwasher when fully loaded Place hollow items bowls glasses and pans face down in the basket Do not put dishes or cutlery with tobacco ash wax lubricating grease or paint residues in the dishwasher Before First Use Set the water softener level as required by the water hardness in the area Add 1kg of salt into the salt compartment and then fill with water to the top of the salt compartment Remove all the packaging materials from the interior of the dishwasher Fill the rinse aid compartment
16. s appliance must be earthed Brown to Live i 13 Amp fuse Cord Clamp Blue to Neutral The mains lead of this appliance has been fitted with a BS 1363A 13 Amp fused plug To change a fuse in this type of plug follow the steps below 1 Remove the fuse cover and fuse 2 Fit replacement 13A fuse ASTA approved to BS 1362 type into the fuse cover 3 Replace fuse cover Important Do not use the appliance without the fuse cover in position How to Connect an Alternative Plug If the fitted plug is not suitable for your socket outlet then it should be cut off and disposed of safely to avoid the risk of electric shock A suitable alternative plug of at least 13 Amp rating to BS 1363 should be used As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug proceed as follows e he wire which is coloured GREEN and YELLOW must be 24 connected to the terminal which is marked with letter E or by the Earth symbol or coloured GREEN and YELLOW e The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK or BLUE e The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED or BROWN If in doubt regarding the electrical connection of this appliance consult a qualified electrician Do not shorten the supply
17. t of a programme e losetthe delay timer press the delay timer button 5 This will switch the timer on for 3 hours e Pressing the delay timer button 5 again will increase the delay to 6 hours a third press increases the time to 9 hours The delay time selected will show on the indicator lights 6 e locancelthe delay timer press the delay timer button again until none of the indicator lights 6 are lit Salt Rinse Aid Warning Lights and End of Programme Light 7 When the dishwasher salt or rinse aid begins to run out the warning light will illuminate to advise that it needs refilling When the programme is complete the dishwasher will emit five beeps and the end of programme indicator light will illuminate Starting a Programme e Press the Power button the end of programme light will be Switched on e Press the Programme Selection button until the required programme is shown on the display 8 e lf required set the delay timer by pressing the Delay Timer button e Once a programme is selected the end of programme light will switch off e When you close the dishwasher door the programme will start automatically Please note The dishwasher stores the most recently used programme in its memory To change the programme simply press the Programme Selection button At the End of a Programme If possible do not open the dishwasher door once the programme has started At the end of a programme the dishwasher
18. will beep five times and the end of Programme Indicator light will switch on Changing a Programme It is possible to change the programme if necessary once the programme has started e First open the door slightly to reduce the risk of water spillage e Press the programme selection button until the required programme is shown on the display e hen close the door The dishwasher will begin the new programme from the point at which the old programme stopped Cancelling a Programme It is possible to cancel the programme once is has started e First open the door slightly to reduce the risk of water Spillage e Press and hold in the Programme Selection button for 9 three seconds until the end of programme indicator flashes anda 1 shows on the display Then close the door The dishwasher will run a drain cycle which will take approximately 30 seconds Once this is complete the dishwasher will beep five times and the end of programme light will switch on Switching the Dishwasher Off Once the dishwasher beeps five times and the end of programme light switches on the dishwasher can be switched off by pressing the Power button Then turn off the water tap and remove the plug from the power Socket Please note the dishwasher will automatically continue on the programme it has started if the door is opened or in the event of a power cut Detergent To Fill the Detergent Compartment 1 2 e Push the latch to
Download Pdf Manuals
Related Search