Zanussi ZGG66424BA hob
Contents
1. kad AA Be very careful when you replace the pan supports to prevent the hob top from damage After cleaning dry the appliance with a soft cloth www zanussi com The stainless steel can become tarnished if it is too much heated Refer to this you must not cook with potstones earthenware pans or cast iron plates Do not use aluminium foil to prevent damage the top during operation Removing the dirt 1 Remove immediately melting plastic plastic foil and food containing sugar Stop the appliance and let it cool down before you clean limescale rings water rings fat stains shiny metallic dis colorations Use a special cleaner appli cable for surface of hob 2 Clean the appliance with a damp cloth and some detergent What to do if 3 At the end rub the appliance dry with a clean cloth Cleaning of the spark plug This feature is obtained through a ceramic igni tion candle with a metal electrode Keep these components well clean to prevent difficult light ing and check that the burner crown holes are not obstructed Periodic maintenance Periodically speak your local Service Force Centre to check the conditions of the gas sup ply pipe and the pressure adjuster if fitted There is no spark when lighting the gas Burner cap and crown are e placed uneven The flame is blow out immediately There is no electrical supply z2. steel wool pads or acids They can cause damage to the appliance Scratches or dark stains on the surface have no effect on how the appliance oper ates You can remove the pan supports to easily clean the hob To clean the enamelled parts cap and crown wash them with warm soapy water and dry them carefully before you put them back Wash stainless steel parts with water and then dry them with a soft cloth 10 cooktop and that pots are centrally positioned on the rings in order to achieve maximum stability and to obtain lower gas consumption Do not place unstable or deformed pots on the rings to prevent from spill and injury Warning Flame diffuser are not recommended Information on acrylamides Important According to the newest scientific knowledge if you brown food specially the one which contains starch acrylamides can pose a health risk Thus we recommend that you cook at the lowest temperatures and do not brown food too much The pan supports are not dishwasher proof They must be washed by hand When you wash the pan supports by hand take care when you dry them as the enamel ling process occasionally leaves rough edges If necessary remove stubborn stains using a paste cleaner Make sure you position the pan supports correctly after cleaning To make the burners work correctly make sure that the arms of the pan supports are in the centre of the burner y
3. Thermocouple is not heated Make sure that the unit is con nected and the electrical supply is switched on Control the fuse If the fuse is released more than one time refer to a qualified electrician Make sure that the burner cap and crown are in correct posi tions After lightning the flame keep after ignition sufficient the knob pushed for approxi mately 5 seconds The gas ring burns unevenly Burner crown is blocked with Make sure that the injector is food residues www zanussi com not blocked and the burner crown is clear of food particles 11 If there is a fault first try to find a solution to the problem yourself lf you cannot find a solution to the problem yourself speak your dealer or the local Service Force Centre i If you operated the appliance incorrectly or the installation was not carried out by a a E MOD MOD registered engineer the visit from the customer service technician or dealer may not take place free of charge even during the warranty period Labels supplied with the accessories bag Stick the adhesive labels as indicated below MOD TYPE PROD NO 230V 50Hz PROD NO PROD NO C 0049 SERNO 1P20 SER NO SER NO e DATA DATA MADE IN ITALY 1 voog MODEL 1 Lo Stick it on Guarantee Card and send this part Stick it on Guarantee Card and keep this part Stick it on instruction booklet These data are necessary to help you quickly
4. and correctly These data are available on the supplied rating plate Model description Technical data Hob dimensions Width Length 594 mm 510 mm Hob recess dimensions Width 560 mm Length 480 mm Heat input 12 Product number PNC Serial Number S N Use the original spare parts only They are available at Service Force Centre and approved spare parts shops Triple Crown burner 4 0 kW 2 0 kW 1 0 kW G20 2H 20 mbar 9 kW G30 3 28 30 mbar 654 g h G31 3 37 mbar 643 g h Semi rapid burner Auxiliary burner TOTAL POWER www zanussi com Electric supply 230 V 50 Hz Appliance class 3 3 core flexible cable with non rewireable e i plug fitted with a 3 amp By pass diameters cartridge fuse By pass in 1 100 Gas connection G 1 2 mm Category 112H3 Auxiliary 28 Gas supply G20 2H 20 mbar Semi rapid 32 Triple Crown 56 Gas burners NORMAL POWER NORMAL POWER NATURAL GAS LPG Butane Propane BURNER G20 2H 20 mbar G30 G31 3 28 30 37 mbar kw Auxiliary 1 0 0 33 70 0 095 50 73 71 Semi rapid 2 0 0 45 96 0 190 71 145 143 EPE 4 0 1 4 146 0 381 98 291 286 Crown Environment concerns information about recycling of this product please contact your local council your household waste disposal service or the shop where you purchased the product The symbol A on the product or on
5. connection Carry out connection by using metal rigid pipes copper with mechanical end Injectors replacement 1 Remove the pan supports 2 Remove the caps and crowns of the burn er 3 With a socket spanner 7 remove the injec tors and replace them with the ones which are necessary for the type of gas you use see table in Technical Data chapter 4 Assemble the parts follow the same pro cedure backwards 5 Replace the rating plate it is near the gas supply pipe with the one for the new type of gas supply You can find this plate in the package supplied with the appliance If the supply gas pressure is changeable or dif ferent from the necessary pressure you must fit an applicable pressure adjuster on the gas sup ply pipe Adjustment of minimum level To adjust the minimum level of the burners 1 Light the burner 2 Turn the knob on the minimum position 3 Remove the knob 4 With a thin screwdriver adjust the by pass screw position The by pass screw lf you change from natural gas G20 20 mbar to liguid gas fully tighten the by pass screw in lf you change from liquid gas to natural gas G20 20 mbar undo the by pass screw approximately 1 4 of a turn 1 2 of a turn for Triple Crown burner Warning Make sure the flame does not go out when you guickly turn the knob from the maximum position to the minimum position Electrical connection The electrical work necessary to i
6. positioned on the rings in order to avoid safety risks Do not use unstable cookware or cookware with damaged bottom There is a risk of tilt ing and accident Do not put flammable products or items that are wet with flammable products fusible ob jects made of plastic or aluminium and or fabrics in near or on the appliance There is a risk of explosion or fire Use only the accessories supplied with the appliance Be careful when you connect the appliance to the near sockets Do not let the electricity bonds touch the appliance or hot cookware Do not let the electricity bonds tangle Installation You must read these instructions The manufacturer is not responsible for any injury to persons and pets or damage to property caused by failure to obey these reguirements To prevent the risks of structural dam age or physical injury installation con nection of the appliance to the power supply and gas system setting up and maintenance must only be done by gualified personnel in compliance with standards and local regulation force Make sure that the appliance is not damaged because of transport Do not connect a dam aged appliance If it is necessary speak to the supplier Only use built in appliances after you assem ble the appliance into correct built in units and work surfaces that obey the standards Do not install the hob over a domestic appli ances if the installation instructions do not al low it In
7. 00 R NP Care and cleaning _____________ 10 What to do if 11 Technical data ________________ 12 Environment concerns 13 Subject to change without notice Set the cooking zones to the off position af ter each use Burners and accessible parts become hot during and after use Do not put cutlery or saucepan lids on the cooking surface Cook ware and its contents can tip over There is a risk of burns Hot fat and oil can ignite very quickly There is a risk of fire Do not let the appliance stay unattended during operation Always monitor the appliance during opera tion Do not let the liquids overflow into the holes on the top of the hob Do not use the hob without cookware The appliance is only for domestic use Do not use the appliance for commercial and in dustrial use Caution This appliance is for cooking purposes only It must not be used for other purposes for example room heating Use only cookware with a diameter applica ble to the dimensions of the burners There is a risk of overheating and rupture of the glass plate if applicable Do not use a pan with a diameter smaller than the burner dimension Flames can heat up the pan handle Refer to the table in the chapter Helpful hints and tips The cookware must not enter the control zone Make sure that the cookware does not pro trude over the edges of the cooking surface www zanussi com and that it is centrally
8. E User manual Hob U S E R MANUAL ZGG66424 Ae ZANUSSI Contents Safety information Installation 2222 22 Product description Operation L L Helpful hints and tips A Safety information Warning These instructions are only valid in the countries whose symbols appear on this booklet s cover For your safety and correct operation of the appliance read this manual carefully before installation and use Always keep these instructions with the appliance even if you move or sell it Users must fully know the operation and safety features of the appliance General safety Warning Persons including children with reduced physical sensory mental capabilities or lack of experience and knowledge must not use the appliance They must have supervision or instruction for the operation of the appliance by a person responsible for their safety Child safety Only adults can use this appliance Children must get supervision to make sure that they do not play with the appliance Keep all packaging away from children There is a risk of suffocation and physical in jury Keep children away from the appliance dur ing and after the operation until the appli ance is cold Use Remove all packaging stickers and the pro tective layer of the stainless steel hob panel if applicable from the appliance before first use Do not remove the rating plate It can in validate the guarantee Oo
9. city you can ignite the burner without electrical device in this case approach the burner with a flame push the relevant knob down and turn it counter clockwise to maximum gas release position If the burner accidentally goes out turn the control knob to the off position and try to light the burner again after minimum 1 minute 3 The spark generator can start automatical ly when you switch on the mains after in stallation or a power cut It is normal Turning the burner off To put the flame out turn the knob to the sym bol Warning Always turn the flame down or switch it off before you remove the pans from the burner Do not use cooking vessels on the hotplate that overlap its edges Burner Diameters of cookware Triple Crown 180 260 mm Front Semi rap 120 180 mm id Bumer Diameters of cookware Rear Semi rap 120 220 mm id Auxiliary 80 160 mm Warning Pots must not enter the control zone Flame will heat up the control zone Do not put the same pan on two burners Warning Make sure pot handles do not protrude over the front edge of the Care and cleaning Warning Deactivate the appliance and let it cool down before you clean it Disconnect the appliance from the electrical supply before you do cleaning or maintenance work Warning For safety reasons do not clean the appliance with steam cleaners or high pressure cleaners Warning Do not use abrasive cleaners
10. e is a risk of electrical shock www zanussi com Important The replacement of the electrical cable must be done by a gualified electrician or competent person according to the current regulations Replacement of the connection cable To replace the connection cable use only HO5V2V2 F T90 or equivalent type Make sure that the cable section is applicable to the volt age and the working temperature The yellow green earth wire must be approximately 2 cm longer than the brown or black phase wire Building In gt min 600 mm N min 150 m min 650 mm min 55 mm 480 m o J aa N a 11 mm C 3 asa y gt Co 4 J A supplied seal B supplied brackets Possibilities for insertion Kitchen unit with door The panel installed below the hob must be easy to remove and let an easy access in case a technical assistance intervention is necessary with vents to let a continuous supply of air The electrical connection of the hob and the oven must be installed separately for safety reasons and to let easy remove oven from the unit a Removable panel b Space for connections Kitchen unit with oven The hob recess dimensions must obey the indi cation and the kitchen unit must be eguipped Product description Cooking surface layout un a g e Cooktop Semi rapid burner Triple Crown burner Q Auxiliary burner j Con
11. ible for the engineer in the event of a breakdown The manufacturer will not accept liability should the above instructions or any of the oth er safety instructions incorporated in this in struction booklet be ignored On the end of the shaft which includes the G 1 2 threaded elbow adjustment is fixed so that the washer is fitted between the components as shown in the diagram Screw the parts to gether without using excessive force End of shaft with nut Washer Elbow Connection to the gas supply should be with either rigid or semi rigid pipe i e steel or cop per The connection should be suitable for connect ing to R 1 2 1 2 BSP male thread When the final connection has been made it is essential that a thorough leak test is carried out on the hob and installation www zanussi com Make sure that the main connection pipe does not exert any strain on the hob If you use flexible metal pipes make sure that they agree to ISO 10380 and ISO 10807 standards Be careful they do not come in touch with mobile parts or they are not squeezed Also be careful when the hob is put together with an oven Important It is important to install the elbow correctly with the shoulder on the end of the thread fitted to the hob connecting pipe Important Failure to ensure the correct assembly will cause leakage of gas Important Make sure that the gas supply pressure of the appliance obeys the recommended values Rigid
12. its packaging indicates that this product may not be treated as household waste Instead it should be taken to the appropriate collection point for the recycling of electrical and Packaging material electronic equipment By ensuring this product O The packaging materials are friendly to the dep oc correctly you will help prevent environment and can be recycled The potential negative consequences waj Me plastic components are identified by marking environment ane human health which aala gt PE lt gt PS lt etc Discard the packaging mate otherwise be caused Dy mappropriate waste rials as household waste at the waste disposal handling of this product For more detailed facilities in your municipality www zanussi com 13 14 www zanussi com www zanussi com 15 www zanussi com shop ES 8 48 ZN fT 397225902 A 112012
13. local authorised facilities for disposal of your appliance air vent of effective area of 100 cm is required If it is installed in a room of volume between 5 m3 and 10 m3 an air vent of effective area of 50 cm is required while if the volume exceeds 11 m no air vent is required However if the room has a door which opens directly to the outside no air vent is reguired even if the volume is between 5 m3 and 11 m3 lf there are other fuel burning appliances in the same room B S 5440 Part 2 Current Edition should be consulted to determine the reguisite air vent reguirements For appliances installed in the Republic of Ire land please refer to the NSAI Domestic Gas Installation I S 813 Current Editions Table Four Location The hob may be located in a kitchen a kitchen diner or bed sitting room with a volume greater than 20 m3 but not in a bathroom or shower room The minimum distance combustible material can be fitted above the hob in line with the www zanussi com edges of the hob is 400 mm If it is fitted below 400 mm a space of 50 mm must be allowed from the edges of the hob For appliances installed in the Republic of Ire land please refer to NSAI Domestic Gas In stallation I S 813 Current Edition Section 7 Permitted Locations of Appliance Gas Connection Warning Any gas installation must be carried out by a GAS SAFE REGISTER installer Make sure that once the hob is installed it is easily access
14. nstall the appliance must be done by a gualified elec trician or competent person according to the current regulations The appliance must be earthed Always use a correctly installed shockproof socket Make sure that there is access to the mains plug after the installation Do not pull the mains cable to disconnect the appliance Always pull the mains plug The appliance must not be connected with an extension cable an adapter or a multiple socket There is a risk of fire Make sure that the ground connection complies with the standards and regulations force The power cable must not touch any hot parts The electrical installation must have an isola tion device which lets you disconnect the ap pliance from the mains at all poles The isola tion device must have a contact opening width of minimum 3 mm You must have the correct isolation devices line protecting cut outs fuses screw type fuses removed from the holder earth leak age trips and contactors The connection cable parts must not be heated to a temperature above 90 C Electrical Requirements Permanent electrical installation must comply with the latest I E E Regulations and local Elec tricity Board regulations For your own safety the installation must be done by a qualified electrician e g your local Electricity Board or a contractor who is on the roll of the National In spection Council for Electrical Installation Con t
15. racting NICEIC The manufacturer declines any liability if these safety measures are not observed The appliance must be connected to a 230 V 50 Hz AC electrical supply Before activating the appliance make sure the electrical supply voltage is the same as that in dicated on the rating plate The rating plate is located on the bottom of the appliance The appliance is supplied with a 3 core flexible supply cord with a 3 amp plug If it is necessary to change the fuse use a 3 amp ASTA ap proved BS 1362 fuse www zanussi com Green and Yellow 3 amp fuse Brown Cord clamp Blue Should the plug need to be replaced for any reason the wires in the mains lead are coloured in accordance with the following code Green and yellow Earth Blue Neutral Brown Live 1 Connect the green and yellow earth wire to the terminal in the plug which is marked with the letter E or the earth symbol or coloured green and yellow 2 Connect the blue neutral wire to the ter minal in the plug which is marked with the letter N or coloured black 3 Connect the brown live wire to the termi nal in the plug which is marked with the let ter L or coloured red There must be no cut or stray strands of wire present The cord clamp must be secured on the outer sheath Warning Make sure that the cut off plug is disposed of safely A cut off plug put into a 13 amp socket is a safety hazard Ther
16. stall the appliance only on a worktop with flat surface Do not change the specifications or modify this product There is the risk of injury and damage to the appliance Fully obey the laws ordinances directives and standards in force in the country where www zanussi com you use the appliance safety regulations re cycling regulations electrical safety rules etc Keep the minimum distances to other appli ances and units Install anti shock protection for example in stall the drawers only with a protective panel directly below the appliance Prevent damage of the cut surfaces of the worktop against moisture with a correct seal ant Seal the appliance to the worktop with no space left with a correct sealant Prevent damage to the bottom of the appli ance from steam and moisture e g from a dishwasher or oven Do not install the appliance adjacent to doors and below windows Hot cookware can be hit off the hob when you open the doors or windows Before installation make sure that the local supply conditions gas type and pressure agree with the adjustment of appliance The adjustment conditions for the appliance are on the rating plate which you can find near the gas supply pipe This appliance is not connected to a com bustion products evacuation device It must be installed and connected in accordance with current installation regulations Particular attention must be given to the relevant re quiremen
17. stallation connection and maintenance must be carried out by qualified personnel in compliance with standards and local regulations in force Important safety requirements This hob must be installed in accordance with the Gas Safety Installation and Use Regula tions Current Edition and the IEE Wiring Reg ulations Current Edition For appliances installed in the Republic of Ire land please refer to NSAI Domestic Gas In stallation l S 813 Current Editions and the ET Cl Rules for Electrical Installations Provision for ventilation Detailed recommendations are contained in the following British Standards Codes Of Practice B S 6172 B S 5440 Par 2 and B S 6891 Current Editions The hob should not be installed in a bed sitting room with a volume of less than 20 m3 If it is installed in a room of volume less than 5 m3 an 4 If the fixing bracket is near to the terminal block always make sure the connection ca ble does not come in contact with the edge of the bracket You must have correct isolation devices line protecting cut outs fuses screw type fuses removed from the holder ground leakage trips and contactors Disposal of the appliance To prevent the risk of physical injury or dam age Disconnect the appliance from the power supply Cut off the mains cable where it connects with the appliance and discard it Flat the external gas pipes if there are fit ted Speak to your
18. trol knobs I 0000 HE Control knobs ET Symbol Description mum gas supply no gas supply off posi O tion minimum gas supply Operation Ignition of the burner 1 Always light the burner before you put A Warning Be very careful when you use cookware open fire in kitchen environment To light the burner Manufacturer decline any responsibility in case 1 misuse of the flame Turn the control knob counterclockwise to the maximum position X and push it down 8 www zanussi com 2 Keep the control knob pushed for approxi mately 5 seconds this will let thermocou ple to warm up If not the gas supply will be interrupted 3 Adjust the flame after it is regular lf after some tries the burner does not light check if the crown and its cap are in correct positions Burner cap Burner crown Ignition candle Thermocouple Helpful hints and tips Energy savings If possible always put the lids on the pans When the liquid starts to boil turn down the flame to barely simmer the liguid Warning Use pots and pans with diameter applicable to the dimension of burner www zanussi com Warning Do not keep the control knob pushed for more than 15 seconds If the burner does not light after 15 seconds release the control knob turn it into off position and try to light the burner again after minimum 1 minute Important In the absence of electri
19. ts regarding ventilation The use of a gas cooking appliance cause heat and moisture in the room in which it is installed Make sure that the ventilation in the kitchen is good keep natural ventilation holes open or install a mechanical ventilation device me chanical extractor hood More ventilation for example opening of a window or increasing the level of mechanical ventilation where present is necessary when you operate the ap pliance with intensity for a long time Carefully obey the instructions for electrical connections There is the risk of injury from electrical current Disconnect the appliance from the elec trical supply before you do the mainte nance work or you clean it The electrical mains terminal is live Make electrical mains terminal free of volt age Install correctly to give anti shock protection A loose and incorrect mains plug and socket connections can make the terminal become too hot A qualified electrician must install the clamp ing connections correctly Use a strain relief clamp on cable Use the correct mains connection cable and replace the damaged mains cable with appli cable cable Speak to your local Service Force Centre The appliance must have the electrical instal lation which lets you disconnect the appli ance from the mains at all poles with a con tact opening width of minimum 3 mm Installation Warning The following instructions about in
Download Pdf Manuals
Related Search