Zanussi ZRG16602WE refrigerator
Contents
1. WARNING This appliance must be earthed The manufacturer declines any liability should these safety measures not be observed The wires in the mains lead are coloured in accordance with the following code 7 A B air DE gt www zanussi com A green and yellow Earth C brown Live D blue Neutral As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug proceed as follows 1 5 Connect the wire coloured green and yellow to the terminal marked either with the letter E or by the earth symbol or coloured green and yellow Connect the wire coloured blue to the terminal either marked with the letter N or coloured black Connect the wire coloured brown to the terminal either marked with the L or coloured red Check that no cut or stray strands of wire is present and the cord clamp E is secure over the outer sheath Make sure the electricity supply voltage is the same as that indicated on the appliance rating plate Switch on the appliance The appliance is supplied with a 13 amp fuse B In the event of having to change the fuse in the plug supplied a 13 amp ASTA approved BS 1362 fuse must be used WARNING A cut off plug inserted into a 13 amp socket is a serious safety shock hazard Ensure that it is disposed of safely 112. Technical information Technical data Height mm 850 Width mm 595 Depth mm 635 Voltage Volts 230 240 Frequency Hz 50 The technical information are situated in the rating plate on the external or internal side of the appliance and in the energy label ENVIRONMENTAL CONCERNS Recycle the materials with the symbol de Put the packaging in applicable containers to recycle it Help protect the environment and human health and to recycle waste of electrical and electronic appliances Do not dispose appliances marked with the symbol x with the household waste Return the product to your local recycling facility or contact your municipal office 12 www zanussi com www zanussi com 13 14 www zanussi com www zanussi com 15 www zanussi com shop ZN fN 212000768 A 222014
3. User Manual U Q R MANUAL Refrigerator ZRG16602WE ZANUSSI Contents Safety information 2 Hints and tips ocoooonronoso l 6 Safety instructions 3 Care and cleaning 6 Operation 5c 2 sans o Ay ia sd 4 Troubleshooting 7 First sez 01 0 e oe 5 Installation 9 Daily ista siii 5 Technical information 12 Subject to change without notice A Safety information Before the installation and use of the appliance carefully read the supplied instructions The manufacturer is not responsible if an incorrect installation and use causes injuries and damages Always keep the instructions with the appliance for future reference Children and vulnerable people safety This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved Do not let children play with the appliance Cleaning and user maintenance shall not be made by children without supervision Keep all packaging away from children General Safety This appliance is intended to be used in household and similar applications such as Farm houses staff kitchen areas in shops offices and other working envir
4. Close and open the door HEEE CWE The compressor operates contin ually Water flows inside the refrigera tor Water flows on the floor Door is misaligned or interferes with ventilation grill The temperature in the appliance is too low too high i brand mark service The lamp is defective Temperature is set incorrectly Many food products were put in at the same time The room temperature is too high Food products placed in the appliance were too warm The door is not closed correct ly The water outlet is clogged Food products prevent that water flows into the water col lector The melting water outlet is not connected to the evaporative tray above the compressor The appliance is not levelled The temperature regulator is not set correctly The door is not closed correct ly The food products tempera ture is too high Many food products are stored at the same time The door has been opened of ten There is no cold air circulation in the appliance If the advice does not lead to the desired result call the nearest Refer to Replacing the lamp Refer to Operation chapter Wait some hours and then check the temperature again Refer to climate class chart on the rating plate Allow food products to cool to room temperature before storing Refer to Closing the door Clean the water outlet Make sure that food products do not touch the rear
5. another person that will keep a firm hold on the doors of the appliance during the operations 1 Unscrew both screws on the rear side wl 3 Unscrew the left foot 4 Unscrew the screws of the door bottom hinge Remove the hinge Put over the pin in the direction of the arrow 10 a Unscrew and install the screw on the opposite side Install the hinge on the opposite side Screw the right foot Unscrew the screws of the door top hinge Remove the hinge Put over the pin in the direction of the arrow Install the hinge on the opposite side POND 11 Put the top in position 12 Push front the top 13 Screw both screws on the rear side 14 Remove and install the handle on the opposite side www zanussi com Do a final check to make sure that All screws are tightened The magnetic seal adheres to the cabinet The door opens and closes correctly If the ambient temperature is cold i e in Winter the gasket may not fit perfectly to the cabinet In that case wait for the natural fitting of the gasket In case you do not want to carry out the above mentioned operations contact the nearest After Sales Service Force The After Sales Service specialist will carry out the reversibility of the doors at your cost Electrical Connection CAUTION Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person
6. plate Attach the melting water outlet to the evaporative tray Refer to Levelling Set a higher lower temperature Refer to Closing the door Let the food products temperature decrease to room temperature be fore storage Store less food products at the same time Open the door only if necessary Make sure that there is cold air cir culation in the appliance www zanussi com Replacing the lamp Disconnect the plug from the mains socket 1 Remove the screw from the lamp cover 2 Remove the lamp cover refer to the illustration 3 Replace the used lamp with a new lamp of the same power and specifically designed Installation WARNING Refer to Safety chapters Positioning This appliance can be installed in a dry well ventilated indoor where the ambient temperature corresponds to the climate class indicated on the rating plate of the appliance Climate Ambient temperature class SN 10 C to 32 C N 16 C to 32 C ST 16 C to 38 C T 16 C to 43 C i Some functional problems might occur for some types of models when operating outside of that range The correct operation can only be guaranteed within the specified temperature range If you have any doubts regarding where to install the appliance please turn to the vendor to our customer service or to the nearest Service Centre www zanussi com for household appliances the maximum power is shown on the
7. plug Use WARNING Risk of injury burns electrical shock or fire Do not change the specification of this appliance Do not put electrical appliances e g ice cream makers in the appliance unless they are stated applicable by the manufacturer Be careful not to cause damage to the refrigerant circuit It contains isobutane R600a a natural gas with a high level of environmental compatibility This gas is flammable f damage occurs to the refrigerant circuit make sure that there are no flames and sources of ignition in the room Ventilate the room Do not let hot items to touch the plastic parts of the appliance Do not store flammable gas and liquid in the appliance Do not put flammable products or items that are wet with flammable products in near or on the appliance Do not touch the compressor or the condenser They are hot Internal light The type of lamp used for this appliance is not suitable for household room illumination Operation Switching on Insert the electrical plug into a wall socket Turn the temperature regulator clockwise to a medium setting Switching off To turn off the appliance turn the temperature regulator to the O position Care and cleaning WARNING Risk of injury or damage to the appliance Before maintenance deactivate the appliance and disconnect the mains plug from the mains socket This appliance contains hydrocarbons in the cooli
8. appliance for the first time the interior and all internal accessories should be washed with lukewarm water and some neutral soap to remove the typical smell of a brand new product then dried thoroughly Daily use WARNING Refer to Safety chapters Movable shelves The walls of the refrigerator are equipped with a series of runners so that the shelves can be positioned as desired Positioning the door shelves To permit storage of food packages of various sizes the door shelves can be placed at different heights 1 Gradually pull the shelf in the direction of the arrows until it comes free 2 Reposition as required www zanussi com If the ambient temperature is high or the appliance is fully loaded and the appliance is set to the lowest temperature it may run continuously causing frost to form on the rear wall In this case the dial must be set to a higher temperature to allow automatic defrosting and therefore reduced energy consumption CAUTION Do not use detergents or abrasive powders as these will damage the finish Hints and tips Normal operating sounds The following sounds are normal during operation A faint gurgling and bubbling sound from coils sound when refrigerant is pumped A whirring and pulsating sound from the compressor when refrigerant is pumped A sudden cracking noise from inside appliance caused by thermic dilatation a natural and not dangerous phy
9. lamp cover Install the lamp cover Tighten the screw to the lamp cover Connect the plug to the mains socket Open the door Make sure that the light comes on NOUA Closing the door 1 Clean the door gaskets 2 If necessary adjust the door Refer to Installation 3 If necessary replace the defective door gaskets Contact the After Sales Service Levelling When placing the appliance ensure that it stands level This can be achieved by two adjustable feet at the bottom in front Location CAUTION It must be possible to disconnect the appliance from the mains power supply the plug must therefore be easily accessible after installation The appliance should be installed well away from sources of heat such as radiators boilers direct sunlight etc Ensure that air can circulate freely around the back of the cabinet To ensure best performance if the appliance is positioned below an overhanging wall unit the minimum distance between the top of the cabinet and the wall unit must be at least 100 mm Ideally however the appliance should not be positioned below overhanging wall units Accurate levelling is ensured by one or more adjustable feet at the base of the cabinet Door reversibility WARNING Before carrying out any operations remove the plug from the power socket CAUTION To carry out the following operations we suggest that this be made with
10. ng unit Only a qualified person must do the maintenance and the recharging of the unit Regularly examine the drain of the appliance and if necessary clean it If the drain is blocked defrosted water collects in the bottom of the appliance Disposal WARNING Risk of injury or suffocation Disconnect the appliance from the mains supply Cut off the mains cable and discard it Remove the door to prevent children and pets to be closed inside of the appliance The refrigerant circuit and the insulation materials of this appliance are ozone friendly The insulation foam contains flammable gas Contact your municipal authority for information on how to discard the appliance correctly Do not cause damage to the part of the cooling unit that is near the heat exchanger Temperature regulation The temperature is automatically regulated To operate the appliance proceed as follows turn the Temperature regulator towards lower settings to obtain the minimum coldness turn the Temperature regulator towards higher settings to obtain the maximum coldness www zanussi com medium setting is generally the most suitable However the exact setting should be chosen keeping in mind that the temperature inside the appliance depends on room temperature how often the lid is opened the quantity of food stored the location of the appliance First use Cleaning the interior Before using the
11. onments By clients in hotels motels bed and breakfast and other residential type environments Keep ventilation openings in the appliance enclosure or in the built in structure clear of obstruction 2 www zanussi com Do not use mechanical devices or other means to accelerate the defrosting process other than those recommended by the manufacturer Do not damage the refrigerant circuit Do not use electrical appliances inside the food storage compartments of the appliance unless they are of the type recommended by the manufacturer Do not use water spray and steam to clean the appliance Clean the appliance with a moist soft cloth Only use neutral detergents Do not use abrasive products abrasive cleaning pads solvents or metal objects Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance If the supply cord is damaged it must be replaced by the manufacturer its service agent or similarly qualified persons in order to avoid a hazard Safety instructions Installation WARNING Only a qualified person must install this appliance Remove all the packaging Do not install or use a damaged appliance Obey the installation instruction supplied with the appliance Always be careful when you move the appliance because it is heavy Always wear safety gloves Make sure the air can circulate around the appliance Wait at least 4 hours befo
12. or stops during normal use The defrost water drains out through a trough into a special container at the back of the appliance over the motor compressor where it evaporates It is important to periodically clean the defrost water drain hole in the middle of the refrigerator Troubleshooting WARNING Refer to Safety chapters What to do if compartment channel to prevent the water overflowing and dripping onto the food inside M ee Periods of non operation When the appliance is not in use for long periods take the following precautions 1 Disconnect the appliance from electricity supply 2 Remove all food 3 Clean the appliance and all accessories 4 Leave the door doors open to prevent unpleasant smells WARNING If the cabinet will be kept on ask somebody to check it once ina while to prevent the food inside from spoiling in case of a power failure The appliance does not operate The mains plug is not connec ted to the mains socket cor rectly There is no voltage in the mains socket The appliance is noisy properly The lamp does not work www zanussi com The appliance is switched off The appliance is not supported The lamp is in stand by Switch on the appliance Connect the mains plug to the mains socket correctly Connect a different electrical appli ance to the mains socket Contact a qualified electrician Check if the appliance stands sta ble
13. re connecting the appliance to the power supply This is to allow the oil to flow back in the compressor Do not install the appliance close to radiators or cookers oven or hobs The rear of the appliance must stand against the wall Do not install the appliance where there is direct sunlight Do not install this appliance in areas that are too humid or too colds such as the construction appendices garages or wine cellars www zanussi com When you move the appliance lift it by the front edge to avoid scratching the floor Electrical connection AN WARNING WARNING Risk of fire and electrical shock The appliance must be earthed All electrical connections should be made by a qualified person Make sure that the electrical information on the rating plate agrees with the power supply If not contact an electrician Always use a correctly installed shockproof socket Do not use multi plug adapters and extension cables Make sure not to cause damage to the electrical components e g mains plug mains cable compressor Contact the Service or an electrician to change the electrical components The mains cable must stay below the level of the mains plug Connect the mains plug to the mains socket only at the end of the installation Make sure that there is access to the mains plug after the installation Do not pull the mains cable to disconnect the appliance Always pull the mains
14. shelf Fruit and vegetables these should be thoroughly cleaned and placed in the special drawer s provided Butter and cheese these should be placed in special airtight containers or wrapped in aluminium foil or polythene bags to exclude as much air as possible Bottles these need a cap and should be stored on the door bottle shelf or if equipped on the bottle rack Bananas potatoes onions and garlic if not packed must not be kept in the refrigerator The accessories and parts of the appliance are not suitable for washing in a dishwasher Periodic cleaning AN CAUTION Do not pull move or damage any pipes and or cables inside the cabinet AN CAUTION Take care of not to damage the cooling system www zanussi com CAUTION When moving the cabinet lift it by the front edge to avoid scratching the floor The equipment has to be cleaned regularly 1 Clean the inside and accessories with lukewarm water and some neutral soap 2 Regularly check the door seals and wipe clean to ensure they are clean and free from debris 3 Rinse and dry thoroughly 4 If accessible clean the condenser and the compressor at the back of the appliance with a brush This operation will improve the performance of the appliance and save electricity consumption Defrosting of the refrigerator Frost is automatically eliminated from the evaporator of the refrigerator compartment every time the motor compress
15. sical phenomenon A faint click noise from the temperature regulator when the compressor switches on or off Hints for energy saving Do not open the door frequently or leave it open longer than absolutely necessary f the ambient temperature is high and the Temperature Regulator is set to low temperature and the appliance is fully loaded the compressor may run continuously causing frost or ice on the evaporator If this happens set the Temperature Regulator toward warmer settings to allow automatic defrosting and so a saving in electricity consumption Hints for fresh food refrigeration To obtain the best performance Care and cleaning WARNING Refer to Safety chapters General warnings CAUTION Unplug the appliance before carrying out any maintenance operation i This appliance contains hydrocarbons in its cooling unit maintenance and recharging must therefore only be carried out by authorized technicians do not store warm food or evaporating liquids in the refrigerator do cover or wrap the food particularly if it has a strong flavour position food so that air can circulate freely around it Hints for refrigeration Useful hints Meat all types wrap in polythene bags and place on the glass shelf above the vegetable drawer For safety store in this way only one or two days at the most Cooked foods cold dishes etc these should be covered and may be placed on any
Download Pdf Manuals
Related Search