Chief NW1F1223 racks
Contents
1. F Tighten Fastener Pencil Mark Apretar elemento de fijaci n Marcar con l piz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com l pis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijaci n Perforar Befestigungsteil l sen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro Bevestiging losdraaien Gat boren Desserrez les fixations Percez un trou Phillips Screwdriver Security Wrench Destornillador Phillips Llave de seguridad Kreuzschlitzschraubendreher Sicherheitsschl ssel Chave de fendas Phillips Chave de seguran a Cacciavite a stella Chiave di sicurezza Kruiskopschroevendraaier Veiligheidssleutel Tournevis pointe cruciforme Cl de s curit NW1 Racks Installation Instructions TOOLS REQUIRED FOR INSTALLATION a y 1 2 5 32 security included 2 A 1 NW1 rack rear section NW1 Hardware Kit PARTS Model NW1F2818 CY ito Parts A B S y O C 2 D 2 F 2 10 24 x 3 8 08 32 x 3 8 Bumper security 3 8 16 x 2 J 1 5 32 security A A T H Latch catch left L2. AND FIRE HAZARD CUTTING OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY ALWAYS make certain area behind mounting surface is free of gas water waste or any other plumbing before cutting drilling or installing fasteners 1 Using the rack rear section A as a template mark the wall at the center of each stud through top mounting slots See Figure 1 2 Drill one 7 32 pilot hole at both marks made in Step 1 See Figure 1 3 Loosely install two 5 16 x 2 1 2 lag bolts P and two 5 16 flat washers Q into pilot holes 4 Hang rack rear section A onto lag bolts and slide to narrow section of mounting slots See Figure 1 5 Tighten lag bolts installed in Step 3 6 Mark the attachment points for the lower mounting slots making sure the attachment points are centered on the studs See Figure 2 NOTE The number of mounting slots varies and is dependent upon NW1 model being installed 7 Drill 7 32 pilot holes at markings for lower mounting holes See Figure 2 8 Use 5 16 x 2 1 2 lag bolts P and 5 16 flat washers Q to complete installing rack rear section A to the wall through the lower mounting holes See Figure 2 Figure 1 Figure 2 NW1 Racks Installation Instructions ASSEMBLY NOTE The NW1 rack may be assembled so that the hinge is located on either the left or the right Assem
3. of factory warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component The wall to which the mount is being attached may have a maximum drywall thickness of 5 8 1 6cm WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components located within the rack does not exceed 300 Ibs 136 1 kg Use with products heavier than the maximum weight indicated may result in instability or collapse of the rack causing possible injury WARNING Use this mounting system only for its intended use as described in these instructions Do not use attachments not recommended by the manufacturer WARNING Never operate this mounting system if it is damaged Return the mounting system to a service center for examination and repair WARNING Do not use this product outdoors IMPORTANT Minimum spacings between the Accessories and components and the AV Equipment Cabinet shall be
4. INSTALLATION INSTRUCTIONS Sectional Wall Rack ic CHIEF NW1 Racks Our Mounts Your Vision NW1 Racks Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved A IMPORTANT SAFETY INSTRUCTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding
5. atch catch right Nn p K 1 Latch assembly o B 1 NW1 rack center section P 8 Q 8 5 16 x 2 1 2 5 16 R 8 i Toggler Installation Instructions NW1 Racks INTRODUCTION The NW1 wall racks have been designed to be mounted onto a 2 x 4 wood stud 16 on center wall IMPORTANT Do NOT load wall rack until after installation is complete INSTALLATION Locate Mounting Site WARNING IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT It is the installers responsibility to make certain the structure to which the mount is being attached is capable of supporting five times the weight of the NW1 and all attached equipment Installing to a Wood Stud Wall Determine location of NW1 wall rack ensuring it is centered between wood studs and will be attached to two 2 x 4 studs NOTE Decide on which side of the NW1 rack the hinge will be located It is possible to place the rack near a corner if required since it is possible to operate the latch from the front of the rack WARNING ELECTRICAL SHOCK HAZARD CUTTING OR DRILLING INTO ELECTRICAL CORDS OR CABLES CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY ALWAYS make certain area behind mounting surface is free of electrical wires and cables before drilling or installing fasteners WARNING EXPLOSION
6. bling Rack Sections 1 Attach the rack center section B to the rack rear section A using two 3 8 16 x 2 socket head cap screws E See Figure 3 ce OOQO o Left latch catch G shown Figure 4 Rubber Bumpers 4 Add rubber bumpers F to front of rack rear section A on side opposite the hinges See Figure 5 Figure 3 Latch Catch 2 Insert appropriate latch catch left or right G or H into slot in NW1 rack and adjust latch catch so that holes in latch catch match up with holes in rack See Figure 4 3 Attach latch catch using two 08 32 x 3 8 Phillips pan head screws D See Figure 4 Alternate location of rubber bumpers Figure 5 Installation Instructions NW1 Racks Latch Assembly 5 Add latch assembly K to inside of rack center section B using two 10 24 x 3 8 button head security screws C from outside of rack 6 Open rack by pushing down on outside end of latch assembly See Figure NN NM NN NN Figure 6 Adjusting Rack Rail The rack rails may be adjusted See Figure 7 7 Loosen rack rail screws and nuts from side brace
7. maintained for safe operation of the equipment when installed in accordance with the National Electric Code ANSI NFPA 70 2008 Operating temperature inside rack shall not exceed 104 F IMPORTANT The W1 sectional wall racks are designed to be mounted to a 2 x 4 wood studs 16 on center wall SAVE THESE INSTRUCTIONS Installation Instructions NW1 Racks a he WET RAC KUNG ALL J USK BLE DEPTH CENTER SECTION WODEL LCi ent i 8 WIDTH C HEIGHT D DEPTH E 229 OO 00 OON E i LET UA FRENETI MERTE CAE ias MATA EAN Ul ITED IEEE AMET 28 9 734 19 1 485 if eoo0o0 1 NWIF2018 300 136 20 18 457 16 0 406 99 13 582 42 9 108 14 1 358 Hp B NWI1F2023 300 1136 20 23 584 21 0 533 22 13 562 42 9 1089 19 1 485 NWI1F2818 300 1136 28 18 457 16 0 1406 22 13 562 56 9 1445 14 1 358 ue min da NW1F2823 300 1136 28 23 584 21 0 1533 22 13 562 56 9 1445 19 1 485 tape a NW1F2828 3001136 28 281711 26 0 1660 22 13 1562 56 9 1445 24 1 612 II NWIE3618 300 1136 36 18 457 16 0 406 99 13 562 70 9 1800 14 1 358 NW1E3623 300 1136 36 23 1584 21 0 1533 22 13 1562 70 9 11800 19 1 485 NW1F3628 300 136 36 28 711 26 0 660 22 13 1562 70 9 1800 24 1 612 A i i D ol D Z te LE Zz MH IFLEDO SHOWA
8. oducts division of Milestone AV Technologies 8800 002098 Rev01 2012 Milestone AV Technologies a Duchossois Group Company www chiefmfg com 08 12 USA International Europe Asia Pacific Tnu TU 6436 City West Parkway Eden Prairie MN 55344 800 582 6480 952 225 6000 877 894 6918 952 894 6918 Franklinstraat 14 6003 DK Weert Netherlands 31 0 495 580 852 31 0 495 580 845 Office No 1 on 12 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477 Pe e A O Lo T ConsuneR
9. s NOTE The number of rack rail screws varies dependent on rack model 8 Slide rack rail forward or back as required 9 Tighten rack rail screws into nuts and torgue to 5 ft lbs Side brace Q ollo Alolle Q y ollo ollo SS gl E ve s jjo o ollo Bee Slo 0 slo a y ge AS A al be Je o sio O v lt Nig 2 O10 a ig Rack o rail o gt A e a E Z LZ y CR F ARA 9 ZZZZ ZG GEF 1 gr o Se 7 a Q Zs LZ LL ZZ Zi Ae Figure 7 LOADING THE RACK NOTE The alignment panels shipped with the racks are optional They may be removed to facilitate loading of the racks Load Distribution A CAUTION BEGIN PLACEMENT OF LOAD AT BOTTOM OF RACK Load rack moving from bottom toward top of rack Loading rack incorrectly may result in instability causing possibly injury and or damage to components 1 Begin placement of components into the rack at the lowest point NOTE Continue placing items into the rack moving from the bottom upward A CAUTION The top of the unit should not be used as a shelf A CAUTION DISTRIBUTE LOAD CORRECTLY Load rack with 2 3 total weight of components in the lower half of rack Loading rack incorrectly may result in instability causing possible injury and or damage to components NW1 Racks Installation Instructions CHIEF Our Mounts Your Vision Chief Manufacturing a pr
Download Pdf Manuals
Related Search