Pro-Ject Debut Carbon (DC)
Contents
1. 5 The recommended downforce for Ortofon OM 10 cartridge is 15mN The recommended downforce for Ortofon 2M Red cartridge is 17 5mN Anti skating force adjustment The anti skating force must be adjusted corresponding to the downforce OJOO Downforce Groove in the stub 15 10 14mN 1 bearing ring ial 15 19mN 2 bearing ring 20mN and higher 3 bearing ring 15 Slip the loop of the anti skating weight s thread over the second groove of the stub to set the correct anti skating force for the factory fitted cartridge Feed the thread through the loop of the wire support 17 Connection to the amplifier The record player has gold plated female RCA phono sockets 14 so you can substitute the interconnect cables supplied with higher quality cables such as the Pro Ject Connect it interconnect cables for connection to the amplifier Use the Phono input sometimes labelled gram disc or RIAA on your amplifier Make sure that the phono input offers correct matching and amplification for the used cartridge Line inputs such as CD Tuner Tape or Video are not suitable Take care of connecting the left and right channels correctly The right channel is usually marked red the left channel black or white Check the manual supplied with your amplifier for relevant information The earthing wire of the tonearm should be connected to the earth terminal on your amplifier if provided If your amplifier does not have an input suitable for ph2. Ortofon 2M Red cartridge 2 Motor 22 Single adapter Connection cable not shown NY Warning of a hazard for the user the unit or possible misuse 5 Important notice Safety instructions Make sure that the plug and the switch are easily accessible at all times Hold the plug when unplugging the power cord Never handle the power cord while your hands are wet or damp Avoid letting liguids enter the device Never place any item containing liquid such as a flower vase V on or near the device Never spill any liquid on the device Never place any naked flame sources such as lighted candles on or near the device The product shall not be used in damp or wet locations next to a bathtub sink swimming pool or any other similar conditions Keep plastic bags away from children to prevent any risk of suffocation Pro Ject Audio Systems Pro Ject Debut Carbon Ortofon OM 10 and Ortofon 2M Red Revision 2014 03 10 3 Set up The deck is supplied partially disassembled and carefully packed to guarantee a safe transport Remove all parts from the transport packaging carefully Make sure the surface you want to place the turntable is levelled use a spirit level Remove the transport lock 18 from the tonearm Store it in the original packaging so it is available for future transportations Fit the drive belt 3 around the hub 4 and the smaller diameter part of the motor pulley 2 Avoid getting sweat or grease on the belt as the
3. r p m repeat the proceedings using the smaller step on the pulley In addition 78 r p m is available after mounting a special pulley which may be purchased as an 5 optional extra For detailed product information please visit the Pro Ject web site www project audio com Useful tips The record player should be positioned on a low resonance surface such as wood or a multiple layer play board to avoid structural vibrations disturbing replay Adjusting the azimuth The cartridge needle must be vertical in the record groove in order to trace the groove wall modulations correctly A small screw at the bearing end of the arm allows to correct incorrect azimuth if your needle is not mounted exactly perpendicular to the cartridge body Open the screw just enough to be able to revolve the arm tube without applying force Please note do not remove the screw completely With the aid of a good magnitying glass adjust the needle until it is vertical in the groove i e perpendicular to the record s surface Ideally this should correspond to the top surface of the cartridge body being parallel to the record surface After adjusting the needle parallel retight the screw carefully Pro Ject Audio Systems Pro Ject Debut Carbon Ortofon OM 10 and Ortofon 2M Red Revision 2014 03 10 5 Azimuth setting screw Please note Under no circumstances should the arm tube be adjusted with the needle still in the record groove Irrepa
4. 0 Project INSTRUCTIONS FOR USE Pro Ject Debut Carbon DC 2 Pro Ject Audio Systems Pro Ject Debut Carbon Ortofon OM 10 and Ortofon 2M Red Revision 2014 03 10 Dear music lover thank you for purchasing a Pro Ject Audio record player In order to achieve maximum performance and reliability with this record player you should study these instructions for use carefully Your turntable has been delivered with a factory fitted and adjusted cartridge Please ignore the cartridge set up instructions unless changing the cartridge at a later date During assembling and adjusting of the deck small parts could be lost if not carefully placed in a suitable receptacle Before starting the assembly make yourself acquainted with the parts listed below and correspondingly numbered in the technical drawings above Separately packed items are marked with an asterisk Parts list Motor brackets with Ortofon pads 2 Stepped drive pulley J Drive belt sa Hook 4 Hub 5 Platter with felt mat 6 Tonearm counterweight ba Downforce scale 7 Tonearm lift lever 8 18 Tonearm rest and removable transport lock 9 Tonearm tube a Tonearm base 10 Lid 1 Lid hinges 12 Hinge fasteners 13 Power supply socket 14 Phono output sockets and earth connection 15 Anti skating weight adjustment scale 16 Anti skating weight 17 Anti skating weight support hoop 19 Power switch 20 Headshell with finger lift and fitted Ortofon OM 10 or
5. arth loop Distorted or inconsistent sound from one or both channels Record player is connected to a wrong input on the amplifier or MM MC switch is setted incorrectly Needle or cantilever is damaged Wrong r p m drive belt is overstretched or dirty platter bearing is without oil dirty or damaged Service Should you encounter a problem which you are not able to alleviate or identify despite the above information please contact your dealer for further advice Only if the problem cannot be resolved there the unit should be sent to the responsible distributor in your country Guarantee repairs will only be effected if the unit is returned correctly packed For this reason we recommend to keep the original packaging Never return a record player without making sure that it is disassembled safely and packed correctly in the original packaging according to the diagrams on the last page of this user guide Please remove these parts and pack them separately lid 10 counterweight 6 anti skating weight 16 platter 5 and belt 3 Put on the cartridge protection cap Insert the transport lock for the tonearm 18 before packing the record player Warranty The manufacturer accepts no responsibility tor damage caused by not adhering to these instructions ES for use and or by transportation without the original packaging Modification or changes to any part of the product by unauthorized persons releases the manufacturer from any liabili
6. do not use a dry cloth Antistatic cleaning fluids are available at specialist stores but must be applied sparingly to avoid damage to rubber parts It is recommended to put on the needle cover before cleaning to avoid damage If the player is not used for a long time the drive belt should be removed to prevent unequal stretching V Always disconnect the record player from the mains power supply as a precaution before maintenance Technical specifications Pro Ject Debut Carbon DC Pro Ject 8 6cc Nominal speeds 33 45 r p m 78 r p m optional Speed variance 33 0 2 45 0 16 Wow and flutter 33 0 12 45 0 11 Signal to noise 68dB Effective tonearm mass 6g Effective tonearm length 8 6 218 5mm Overhang 18 5mm Power consumption AW OW in Stand By Outboard power supply 15V 0 0 8mA DC set at 0 5mA universal power supply 6 Pro Ject Audio Systems Pro Ject Debut Carbon Ortofon OM 10 and Ortofon 2M Red Revision 2014 03 10 Dimensions W x H x D 415x118 x 320mm dust cover open 415 x 365 x 405mm Weight 5 6kg Technical specifications MM Cartridge Ortofon OM 10 Frequency range 20 22 000Hz Channel separation 22dB 1kHz Output voltage AmV Recommended load impedance 47kohms amplitier connection MM input Compliance stylus type 25um mN elliptical Recommended tracking force 15mN Weight 5g Technical specifications MM Cartridge Ortofon 2M Red Frequency range 20 22 000Hz Channel separation 22dB 1kHz Output v
7. oltage 5 5mV Recommended load impedance 47kohms amplitier connection MM input Compliance stylus type 20um mN elliptical Recommended tracking force 18mN Weight 7 29 Pro Ject Audio Systems Pro Ject Debut Carbon Ortofon OM 10 and Ortofon 2M Red Revision 2014 03 10 Potential incorrect use and fault conditions Pro Ject Audio Systems turntables are manufactured to the highest standards and undergo strict quality controls before leaving the factory Faults that may possibly occur are not necessarily due to material or production faults but can sometimes be caused by incorrect use or unfortunate circumstances Therefore the following list of common fault symptoms is included The platter does not turn although the unit is switched on The unit is not connected to the mains power supply No mains at the socket Drive belt is not titted or has slipped off No signal through one or other channel or both channels No signal contact from the cartridge to the internal tonearm wiring or from that to the arm lead or from that to the phono box or between that and the amplifier This could be due to a faulty plug broken wire or solder joint or missing plug socket connection Phono input is not selected at amplifier Amplifier is not switched on Amplifier or speakers are defective or muted No connection to the loudspeakers Strong hum on phono input No earth connection from cartridge or arm or arm cable to amplifier or e
8. ono cartridges you will require a separate phono amplifier stage for MM or MC cartridges which is then connected between the record player and a free line level input of the amplifier For detailed product information regarding Pro Ject Audio interconnect cables and phono amplifiers please visit the Pro Ject web site www project audio com 4 Pro Ject Audio Systems Pro Ject Debut Carbon Ortofon OM 10 and Ortofon 2M Red Revision 2014 03 10 5 The recommended load impedance for the factory fitted cartridges is 47kohms MM input Mains power connection The turntable is supplied with the universal power supply with 3 exchangeable sockets adapters suitable for all countries Select the correct adapter for your country and insert the adapter to the exchangeable part of the power supply Connect the low voltage plug from the power supply to the socket 13 on the rear of the record player before connecting the power supply to the mains Mounting the lid Put the lid dust cover 10 carefully over the hinge prongs and adjust the screws 12 until the lid stays open where you want it to without being too stiff to open or close Switching on and off Pressing the power switch 19 alternately starts or stops the motor Changing replay speed To play records at 45 r p m remove the platter 5 Use the accessory tool provided 3a and hook the belt 3 over the larger diameter part of the motor pulley 2 Put the platter on To revert to 33
9. rable damage may be caused to the cantilever suspension The arm must be ies lifted to make each adjustment and lowered afterwards to check it Mounting and connecting the cartridge All cartridges with half inch mounting holes can be fitted Leave the needle s protection cover on and put the cartridge on the headshell by using the cartridge supplied screws Pass one screw through each slot in the headshell 20 Do not tighten the nuts yet Connect the tonearm wires to the cartridge pins as follows white left channel positive L red right channel pos R green right channel return R blue left channel return L The full sound quality of the record player can only be achieved if the cartridge is adjusted correctly Particular tools like the Pro Ject Audio Systems alignment tool are required to accomplish this job properly If you are not well acquainted with the adjustment of cartridges you are advised to call upon the willing help of your Pro Ject dealer to accomplish it for you Please note Adjusting a cartridge and tonearm calls for the greatest care in order to avoid damaging the cartridge or tonearm bearings Leave this work to your dealer if you are in any way unsure of the necessary steps and precautions to be taken Maintenance and cleaning Your record player requires little or no regular maintenance Remove dust with a slightly moistened antistatic cloth To avoid static electricity which attracts even more dust
10. se will deteriorate the performance and reduce the belt s lifespan Use absorbent kitchen paper to remove any oil or grease from the outer edge of the hub and the belt Put the platter 5 and felt mat over the spindle of the hub 4 Cartridge downforce adjustment The counterweights 6 supplied are suitable for cartridges weighing between 4 5 6g Ortofon OM 10 weight no 80 and 6 5 8 59 Ortofon 2M Red weight no 8 Turn the counterweight 6 onto the rear end of the tonearm tube 9 so that the downforce scale 6a shows towards the front of the player Lower the arm lift and place the cartridge in the space between arm rest and platter Rotate the counterweight 6 until the arm tube is balanced The arm should return to the balanced position if it is moved up or down This adjustment must be done carefully Do not forget to remove the cartridge protection cap if fitted before balancing the arm tube Once the arm is balanced correctly return it to the rest Hold the counterweight 6 without moving it and gently revolve the downforce scale ring 6a until the zero is in line with the anti skating prong 15 Check if the arm is still balanced Rotate the counterweight counter clockwise seen from the front to adjust the downforce according to the cartridge manufacturers recommendations One mark on the scale represents 1 MN 0 1g 0 1 Pond of downforce Please note Adjust the downforce before installing the anti skating weight
11. ty over and above the lawful rights of the customer Pro Ject Audio Systems is a registered Trademark of H The information was correct at the time of going to Lichtenegger press The manufacturer reserves the right to make This guide was produced by Pro Ject Audio Systems changes to the technical specification without prior Copyright 2014 All rights reserved notice as deemed necessary to uphold the ongoing process of technical development 8 Pro Ject Audio Systems Pro Ject Debut Carbon Ortofon OM 10 and Ortofon 2M Red Revision 2014 03 10 Accessories Instruction for use Tonearm transport lock Platter Pro Ject Audio Systems Pro Ject Debut Carbon Ortoton OM 10 and Ortoton 2M Red Revision 2014 03 10 9
Download Pdf Manuals
Related Search