Xtreme 18513 flat panel wall mount
Contents
1. fig 2 2 fig 2 3 and fig 2 4 NOTE For flat back screens proceed to step 2 1 For bump out or recessed back screen skip to step 2 2 XTREME MOUNTS AND BRACKETS 4 Customer Service 877 536 8766 www XtremeCables net For Flat Back Screen 3 Hang the brackets mounted TV onto the wall plate Begin with the shortest length screw hand thread through washer and adapter bracket into screen as shown below Screw must make at least three full turns into mounting hole and fit snug into place Do not over tighten If screw cannot make three full turns into screen select a longer length screw from the baffled fastener pack Repeat for remaining mounting holes level brackets and tighten screws Warning A minimum of two qualified people are required for this operation Loosen the safety screw on the display brackets Hook the TV mounted display brackets over the top of the wall plate as shown in fig 3 1 Tighten the safety screws on the display brackets with a proper screw driver as shown in fig 3 1 NOTE S t be d de di the ty f saeg NY ike akaa aea MOONS OPS See Important Make sure the TV is correctly hooked and the safety locking screws are locked safely before loosening the TV For Bump out or Recessed Back Screen Begin with longer length screw hand thread through washer adapter bracket and spacer into screen as2. hardware and components Never exceed the maximum load capacity If mounting to wood wall studs make sure that mounting screws are anchored into the center of the studs Use of an edge to edge stud finder is highly recommended Always use an assistant or mechanical lifting equipment to safely lift and position equipment Tighten screws firmly but do not over tighten Over tightening can damage the items greatly reducing their holding power This product intended for indoor use only Using this product outdoors could lead to product failure and personal injury 1 XTREME Customer Service 877 536 8766 MOUNTS AND BRACKETS www XtremeCables net Component Checklist IMPORTANT Ensure you have received all parts against the component checklist prior to installing If any parts are missing or faulty telephone the special franchiser for a replacement i wall plate x1 left adapter right adapter A bracket x1 bracket x1 B c Package M u mw as M4x10 x4 M4x20 x4 M5x10 x4 M5x20 x4 M A M B M C M D aiai mw mm M6x10 x4 M6x20 x4 M8x15 x4 M8x30 x4 M E M F M G M H naa W D washer x4 014x06x10 x4 015x08x15 x4 M I r M K Package W i 06 5x024 washer x6 ST6 3x55 lag bolt x6 A concrete anchor x6 W B Tools required Phillips Head Screw driver 200mm length exclude the handle
3. shown below E Pitching angle adjustment Screw must make at least three full turns into mounting hole and fit snug into place Do not over tighten ig angle adj If screw cannot make three full turns into screen select a longer length screw from the baffled fastener pack Use the tilt adjusting knob to adjust your TV to the desired angle the pitching angle can be adjusted Repeat for remaining mounting holes level brackets and tighten screws between 0 10 as shown in fig 4 1 Tilt adjusting knob 6 5 XTREME customer Service 877 536 8766 XTREME Customer Service 877 536 8766 MOUNTS AND BRACKETS www XtremeCables net MOUNTS AND BRACKETS www XtremeCables net
4. M6 Socket and Wrench Electric drill and 10mm masonry bit for concrete wall installation Marking Pen Hammer 2 XTREME be Customer Service 877 536 8766 www XtremeCables net MOUNTS AND BRACKETS WOOD STUD WALL MOUNTING A WARNING Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components Tighten wood screws firmly but do not over tighten Over tightening can damage the screws greatly reducing their holding power Make sure that mounting screws are anchored into the center of the studs Use of an edge to edge stud finder is highly recommended Hardware provided is for attachment of mount through standard thickness drywall or plaster into studs Installers are responsible to provide hardware for other types of mounting situations Wall plate can be mounted to two studs Use a stud finder to locate the edges of the studs Use of an edge to edge stud finder is highly recommended Based on their edges draw a vertical line down each stud s center Place wall plate on wall as a template And mark the center of the four mounting holes Make sure that the mounting holes are on the stud centerline Drill four 1 8 3mm dia Holes 1 2 30mm deep secure it using four lag bolts W A and four M6 washers W C as shown in fig 1 1 SOLID BRICK AND CONCRETE BLOCK MOUNTING A WARNING When installing wall mounts
5. Maintenance IM Once you have mounted the bracket and the flat screen check that they are sufficiently secure and safe to use You should check whether screws are fixed well each two months If you have any doubts regarding the installation please consult our retailer or service department for detail MOUNTS AND BRACKETS INSTALLATION INSTRUCTIONS Flat Adjustable Wall Bracket With Tiltand Level 32 60 TV Screens 000000000000 000000000000 fecoocoocaoa CEEE CEELEN CEEE 50k 9 Pitching angle 110lbs MAX 0 10 XIRJA Z MOUNTS AND BRACKETS Customer Service 877 536 8766 Customer Service 877 536 8766 www XtremeCables net I tem 18013 www XtremeCables net I tem 18013 NOTE Read entire instruction sheet befc e you start installati WARNING Do not begin the installation of the product before you have read and understood the instructions and warnings contained in this installation sheet If you have any question regarding any of the instruction or warning Please contact your local distributor Please refer to the installation guide recommendation for required distance from wall to avoid risk of property damage This product should only be installed by someone of good mechanical aptitude with experience and basic building and fully understands Make sure that the supporting surface will safely support the combined load of the equipment and all attached
6. on cinder block verify that you have a minimum of 1 3 8 of actual concrete thickness in the hole to be used for the concrete anchors Do not drill into mortar joints Be sure to mount in a solid part of the block generally 1 minimum from the side of the block It is suggested electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components Customer Service 877 536 8766 www XtremeCables net XTREME MOUNTS AND BRACKETS Use the wall plate as a template to mark six holes locations on the wall Four in the top row slots and two more in the bottom row as shown in fig 1 2 Pre drill these holes with a 10mm masonry bit to at least 60mm in depth Insert a concrete anchor W B into each of these holes Attach the wall plate to the wall using six lag bolts W A and six M6 washers W C as shown in fig 1 3 F Installing Adapter Brackets To prevent scratching the screen set a cloth on a flat level surface that will support the weight of the screen Place screen face side down Place adapter brackets on the back of screen align to holes as shown in fig 2 1 Attach the adapter brackets to the back of the screen using the appropriate combination of screws washers spacers as shown in
Download Pdf Manuals
Related Search