ECX Torment
Contents
1. INSTALLING THE BATTERY INTHE VEHICLE 1 Turn the battery clips A clockwise to remove the battery strap 2 Install a fully charged battery 3 Install the battery strap 4 Turn the battery clips counterclockwise to secure the battery strap If desired you can put foam blocks ECX2015 in front of the battery so the weight of the battery increases rear traction or in back of the battery to increase steering response TORMENT 5 TRANSMITTER CONTROLS REVERSE SWITCH Allows you to change the direction of steering ST REV and throttle TH REV controls default settings are N for steering and R for throttle STEERING RATE STEERING TRIM L im lt Adjusts the amount the front wheels move when the Adjust to make the vehicle steering wheel is turned left drive straight with no input or right at the steering wheel STEERING WHEEL THROTTLE TRIM AS pains Adjusts the neutral point of the electronic speed control Control steering Right and Left steering with ST REV switch on N see ST REV switch POWER SWITCH Power on or off the transmitter THROTTLE TRIGGER BATTERY LEVEL INDICATOR A Reverse mm Solid Green Battery Ke when TH voltage is good above REV switch uc AV Forward Stop on AN Flashing Green Battery on voltage is critically low l below 4V Replace Controls power2. 7 Compliance Information for the European Union 13 Installing the Vehicle BODY Em 7 Parts Diagrams 50 Pa ES Can EEA AE A AAE 52 2 TORMENT WATER RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS Your new Horizon Hobby vehicle has been designed and built with a combination of waterproof and water resistant components to al low you to operate the product in many wet conditions including puddles creeks wet grass snow and even rain While the entire vehicle is highly water resistant it is not completely waterproof and your vehicle should NOT be treated like a submarine The various electronic components used in the vehicle such as the Electronic Speed Control ESC and servo s are waterproof however most of the mechanical components are water resistant and should not be submerged Metal parts including the bearings hinge pins screws and nuts as well as the contacts in the electrical cables will be susceptible to corrosion if additional maintenance is not performed after run ning in wet conditions To maximize the long term performance of your vehicle and to keep the warranty intact the procedures described in the Wet Conditions Maintenance section below must be performed regularly if you choose to run in wet conditions If you are not willing to perform the additional care and mainte nance required then you should not operate the vehicle in those conditions CAUTION Failure to exercis
3. This model is controlled by a radio signal subject to interference from many sources outside your control This interference can cause momentary loss of control so it is advisable to always keep a safe distance in all directions around your model as this margin will help avoid collisions or injury e Never operate your model with low transmitter batteries e Always operate your model in open spaces away from full size vehicles traffic and people e Never operate the model in the street or in populated areas for any reason e Carefully follow the directions and warnings for this and any optional support equipment chargers rechargeable battery packs etc you use Keep all chemicals small parts and anything electrical out of the reach of children e Never lick or place any portion of the model in your mouth as it could cause serious injury or even death e Exercise caution when using tools and sharp instruments e ake care during maintenance as some parts may have sharp edges Immediately after using your model do NOT touch equipment such as the motor electronic speed control and battery because they generate high temperatures You may burn yourself seriously touching them Do not put fingers or any objects inside rotating and moving parts as this may cause damage or serious injury e Always turn on your transmitter before you turn on the receiver in the car Always turn off the receiver before turning your transmitte
4. TE C L TORMENT ECX03006 ECX03006AU ECX03006l ECX03007 ECX03007AU ECX030071 INSTRUCTION MANUAL BEDIENUNGSANLEITUNG MANUEL D UTILISATION MANUALE DI ISTRUZIONI 1 10 ELECTRIC SHORT COURSETRUCK Congratulations on your purchase of the Torment Short Course Truck This 1 10 scale model introduces you to the sport of RC driving Herzlichen Gl ckwunsch zum Kauf des ECX Torment Short Course Truck Dieses 1 10 Scale Model ffnet Ihnen die Welt des RC Car Sports Nous vous f licitons pour l achat du ECX Torment Short Course Truck Ce mod le 1 10 vous initie la conduite RC Congratulazioni per l acquisto di questo Torment Short Course Truck ECX Questa vettura in scala 1 10 vi introdurr nel mondo dei modelli RC NOTICE All instructions warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby Inc For up to date product literature visit http www horizonhobby com and click on the support tab for this product Meaning of Special Language The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product NOTICE Procedures which if not properly followed create a possibility of physical property damage AND little or no possibility of injury CAUTION Procedures which if not properly followed create the probability of physical property damage AND a possibility of serious inj
5. Speed 0 23sec 60 degrees of travel Size 55 6 x 18 x 30mm Electronic Speed Control ESC Input Voltage 4 8 8 4 Electric Capacity FET Forward 30 A 300 A Electric Capacity FET Reverse 15 A 150 A PWM Frequency 1kHz BEC Voltage 5 6 V 1 A Size 46 4 x 36 9 x 28 25 Weight 169 TORMENT 3 2 Spektrum DX2E Transmitter 3 AA 4 Batteries 4 DYN4113 2A Peak Battery Charger 5 Dynamite Speedpack 7 2V Ni MH battery DYN1050EC COMPONENTS VEHICLE PREPARATIONS CHARGING THE VEHICLE BATTERY 1 Connect the AC power cord to the power slot on the charger then connect the other end of the power cord to an AC power source 2 The Power LED and Charging LED will turn GREEN when the charger is connected to the AC power source 3 Connect the battery pack connector to the charge connector 4 Press the On Off button to charge the battery The Charging LED turns RED 5 When the battery pack is fully charged the Charging LED will turn GREEN 6 Press the On Off button to stop charging Disconnect the battery pack connector from the charge connector A CAUTION If at any time during the charge process the battery pack s becomes hot to the touch unplug the battery immediately and discontinue the charge process The vehicle battery charger produces 2000 milliAmps 2 Amps per hour Divide the mAh capacity on the label of a battery by 2000 to know how long battery charging will require For example a fully disc
6. and a brief summary of the problem copy of your original sales receipt must be included for warranty consideration Be sure your name address and RMA number are clearly written on the outside of the shipping carton NOTICE Do not ship LiPo batteries to Horizon If you have any issue with a LiPo battery please contact the appropriate Horizon Product Support office Warranty Requirements For Warranty consideration you must include your original sales receipt verifying the proof of purchase date Provided warranty conditions have been met your Product will be serviced or replaced free of charge Service or replacement decisions are at the sole discretion of Horizon Non Warranty Service Should your service not be covered by warranty service will be completed and payment will be required without notifica tion or estimate of the expense unless the expense exceeds 50 of the retail purchase cost By submitting the item for service you are agreeing to payment of the service without notification service estimates are available upon request You must include this request with your item submitted for service Non warranty service estimates will be billed a minimum of hour of labor In addition you Will be billed for return freight Horizon accepts money orders and cashier s checks as well as Visa MasterCard American Express and Discover cards By submitting any item to Horizon for service you are agreeing to Horizon s Terms and Conditi
7. de d montage de l hexagone la goupille peut sortir de l axe et tomber Quando montate le ruote accertatevi che il trascinatore esagonale sia allineato con la spina del mozzo ruota Quando togliete il trascinatore esagonale la spina pu sfilarsi dal mozzo TORMENT 53 Replacement Parts Ersatzteile Pi ces de rechange Pezzi di ricambio Part Nummer Numero Codice CX2008 Main Chassis hassis h ssis principal X1028 Servo Saver Set auve servo CX2011 Cover and Rear Mount ee und hinterer Capot et fixations arri res X1050 etscrew M3x12 4 Schrauben Set M3x12 4 Jeu de vis M3x12 4 Description Beschreibung Description Descrizione Telaio principale Set salvaservo Copertura e set montaggio posteriore Grani M3x12 4 C2 N oO Mm OO NIN gt mi 5 ECX2015 Foam Block schaum Block Bloc de mousse opugna distanziale batteria Motor Screw Washer Set Motorschrauben Viti per il motore set di ECX1098 Unterlegscheiben Vis Moteur Set Rondelles randella 7 ECX1058 Ball Stud 6 Kugelkopf 6 Rondelle 6 fere Uniball 6 ECX1065 houlder Screw Set 8 Passschrauben Set 8 eu de vis paul es 8 et viti a doppio stadio 8 Ricevitore Sport con rivesti mento protettivo Servo per lo sterzo imper meabile iastra fermabatteria et paraurti ant Wel PMISR201 2 Ch DSM Sport 2 Kanal DSM Sport R cepteur DSM 2 voies Receiver Coated Empf nger beschic
8. included Item Number s ECX03006l ECX030071 Equipment class 2 The object of declaration described above is in conformity with the requirements of the specifications listed below following the provisions of the European R amp TTE directive 1999 5 EC Directive 2004 108 EC and LVD Directive 2006 95 EC EN 300 328 1 7 1 2006 EN 301 489 1 V1 7 1 2006 EN 301 489 17 V1 3 2 2008 EN 60950 1 2006 A11 2009 A1 2010 A12 2011 EN 55022 2010 AC 2011 EN 55024 2010 EN 61000 3 2 2006 A1 2009 A2 2009 EN 61000 3 3 2008 C ODT ANL Steven A Hall Signed for and on behalf of Horizon Hobby Inc Champaign IL USA Feb 09 2013 Horizon Hobby Inc Instructions for disposal of WEEE by users in the European Union This product must not be disposed of with other waste Instead it is the user s responsibility to dispose of their waste equipment by handing it over to a designated mmm Collections point for the recycling of waste electrical and electronic equipment The separate collection and recycling of your waste equipment at the time of disposal will help to con serve natural resources and ensure that it is recycled in a manner that protects human health and the environment For more information about where you can drop off your waste equipment for recycling please contact your local city office your household waste disposal service or where you purchased the product Executive Vice President and Chief Operatin
9. make sure both arms are parallel with the flat surface Lowering the front ride height increases steering but decreases traction Lowering the rear ride height increases traction but decreases steering Part Description FASTENERS No Description No Description No Description No Description TAPPING TAPPING STEP SCREW WASHER ier HEAD gc eege M3x0 5x7 4mm 5x7x0 5mm x10mm WASHER 3x8x0 5mm WASHER 2x x0 5mm TAPPING BINDER H FLANGED STEP SCREW M3x0 5x13 4mm aum STEP SCREW M3x0 5x10 5mm SETSCREW M3x3mm SETSCREW M3x12mm SET SHAFT TAPPING BINDER BINDER HEAD HEAD M3x16mm M3x12mm TAPPING BINDER BINDER HEAD HEAD M3x18mm M3x20mm TAPPING 5 FLATHEAD W M3x10mm TAPPING BINDER HEAD BINDE M3x12mm M3x8mm B LOCK NUT M3 BUTTON FLAT HEAD M3x12mm TAPPING FLAT HEAD M3x15mm 10 HEX M2 5x4mm BUTTON HEX M2 5x8mm SCREW M3x13mm E CLIP E2 5 G LOCK WASHER BINDING Binding is the process of programming the receiver to recognize the GUID Globally Unique Identifier code of a single specific transmitter The DX2E and SR201 are bound at the factory If you need to rebind follow the instructions below With the receiver off insert the bind plug into the BIND port on the receiver NO Power the receiver through any other port The orange LED will flash continuously indicating the receiver is in bind mode oO With the
10. monitor the temperature of the battery pack while charging Always end the charging process if the charger or battery becomes hot to the touch or starts to change form during the charge process e Always charge in a well ventilated area 4 TORMENT INSTALLING TRANSMITTER BATTERIES We recommend using only alkaline AA batteries in the transmitter however it is possible to use rechargeable NIMH batteries A CAUTION If using rechargeable batteries charge only rechargeable batteries Charging non rechargeable batteries may cause the batteries to burst resulting in injury to persons and or damage to property e NEVER install damaged batteries batteries of mixed types or batteries of different ages in the transmitter Remove exhausted batteries e NEVER store the transmitter with batteries installed 1 Slide the panel open on the bottom of the transmitter 2 Obey the battery plus and minus diagram in the transmitter to install 4 AA batteries 3 Slide the panel closed TRANSMITTER BATTERY SAFETY PRECAUTIONS e Never install damaged batteries e Always remove batteries before storing the transmitter e Never install batteries of mixed types or of different ages in e Low battery power can result in loss of control of the RC the transmitter vehicle e Always remove exhausted batteries REMOVING THE VEHICLE BODY
11. of Horizon exceed the individual price of the Product on which liability is asserted As Horizon has no control over use setup final assembly modification or misuse no liability shall be assumed nor accepted for any resulting damage or injury By the act of use setup or assembly the user accepts all resulting liability If you as the purchaser or user are not prepared to accept the liability associated with the use of the Product purchaser is advised to return the Product immediately in new and unused condition to the place of purchase Law These terms are governed by Illinois law without regard to conflict of law principals This warranty gives you specific legal rights and you may also have other rights which vary from state to state Horizon reserves the right to change or modify this warranty at any time without notice WARRANTY SERVICES Questions Assistance and Services Your local hobby store and or place of purchase cannot provide war ranty support or service Once assembly setup or use of the Product has been started you must contact your local distributor or Horizon directly This will enable Horizon to better answer your questions and CONTACT INFORMATION Country of Purchase Horizon Hobby United States of America Horizon Service Center Electronics and engines Horizon Product Support United Kingdom Horizon Hobby Limited Address 4105 Fieldstone Rd Champaign Illinois 61822 USA Units 1 4 Ployters Rd Stap
12. that may cause undesired operation A CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This product contains a radio transmitter with wireless technology which has been tested and found to be compliant with the ap plicable regulations governing a radio transmitter in the 2 400GHz to 2 4835GHz frequency range maintain a separation distance of at least 5 cm between your body excluding fingers hands wrists ankles and feet and the antenna to meet RF exposure safety requirements as determined by FCC regulations The following illustrations show the approximate 5 cm RF exposure area and typical hand placement when operating your Spektrum Antenna Separation Distance transmitter When operating your Spektrum transmitter please be sure to IC INFORMATION This device complies with Industry Canada license exempt RSS standard s Operation 1 subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause unde sired operation of the device COMPLIANCE INFORMATION FORTHE EUROPEAN UNION DK PT RO SE Si SK UK Declaration of Conformity in accordance with ISO IEC 17050 1 No HH2013020904 Product s ECX 1 10 th Scale Short Course Truck Torment V2 1 Spektrum DX2E Transmitter and SR201 Receiver
13. ben Set Jeu de rondelles oet rondelle ECX1055 Bearings 10x15x4 2 Lager 10x15x4 2 Roulements 10x15x4 2 Cuscinetti 10x15x4 2 ECX1059 M3 Locknut 4 M3 Stopmutter 4 Ecrou auto frein M3 4 Dadi autobloccanti M3 4 40 ECX232006 Spur Gear Hauptzahnrad Corona d TORMENT GA Part Nummer i 2 m M Num ro Codice Description Beschreibung Description Descrizione ECX1073 19 Tooth Pinion Gear itzel 19 Z hne Pignon 19 dents ignone a 19 denti DYN1172 Motor Cl gt CX1048 Body Clip Body Clip Clips Carrosserie lippe per carrozzeria l Set di sostegni per la ECX2010 Body Post Set oet Plots Carrosserie Aufnahme Set di montaggio per la 45 ECX2009 Body Mount Set Kargssanaheltor oet Montage Carrosserie 46 Kid Plate Set 4 ear Holder Set Set Halter hinten I ei de Maintien Ae 1 48 op Shaft Spacer Set di spessori Setscrew M3x10 9 9 44 5 et supporto posteriore J ECX4006 Rear Bumper Set Hinterer Stofsf nger Set Set de parechoc arri re ECX4004 Nerf Bar Set eitenaufprallschutz Set de protection lat rales Set protezione laterale 52 ECX4007 Mud Flap Set Body Silver Blue ECX Torment Karosserie Carrosserie argent bleue ECX230006 Tonnen Silber Blau Torment Carrozz Blu Arg Torment Body Black Green ECX Torment Karosserie Carrosserie noire verte ECX230007 Torrent Schwarzi Gr n Torment Carrozz Nero Verde Torment __ 2300 2 Chargeur d te
14. crease torque and motor life when running in mud deeper puddles or any wet conditions that will increase the load on the motor for an extended period of time Wet Conditions Maintenance e Remove the battery pack s and dry the contacts If you have an air compressor or a can of compressed air blow out any water that may be inside the recessed connector housing e Remove the tires wheels from the vehicle and gently rinse the mud and dirt off with a garden hose Avoid rinsing the bearings and transmission NOTICE Never use a pressure washer to clean your vehicle e Use an air compressor or a can of compressed air to dry the vehicle and help remove any water that may have gotten into small crevices or corners e Spray the bearings drive train fasteners and other metal parts with WD 40 solvent or any other water displacing light oil Do not spray the motor e Let the vehicle air dry before you store it Water and oil may continue to drip for a few hours e Increase the frequency of disassembly inspection and lubrication of the following e Front and rear axle hub assembly bearings e All transmission cases gears and differentials e Motor clean with an aerosol motor cleaner and re oil the bushings with lightweight motor oil SPECIFICATIONS Transmitter Frequency 2 4GHz Modulation DSM 05 2 Marine Battery 4 Power Supply 4 8V 6V shared with receiver Output Torque 41 66 oz 3 kg cm Operating
15. ction 2A Caricabatterie a a DYN4113 2A Peak Charger 2A Peak Ni MH Ladegerat de pics rilevamento di picchi DYN1050EC Ni MH battery Ni MH akku Batterie Ni MH Batteria Ni MH TORMENT 55 BS NM ECX03006 ECX03006AU ECXO03006l ECX03007 ECX03007AU ECX03007l1 www ecxre com 37973 Created 1 2013 2013 Horizon Hobby Inc ECX the ECX logo Torment Dynamite and Speedpack are trademarks or registered trademarks of Horizon Hobby Inc WD 40 is a registered trademark of WD 40 Manufacturing Company The Spektrum trademark is used with permission of Bachmann Industries Inc
16. d Horizon dealer or vi Product not compliant with applicable technical regulations OTHER THAN THE EXPRESS WARRANTY ABOVE HORIZON MAKES NO OTHER WARRANTY OR REPRESENTATION AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF NON IN FRINGEMENT MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER S INTENDED USE Purchaser s Remedy Horizon s sole obligation and purchaser s sole and exclusive remedy shall be that Horizon will at its option either 1 service or ii replace any Product determined by Horizon to be defective Horizon reserves the right to inspect any and all Product s involved in a war ranty claim Service or replacement decisions are at the sole discre tion of Horizon Proof of purchase is required for all warranty claims SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER S SOLE AND EXCLUSIVE REMEDY Limitation of Liability HORIZON SHALL NOT BE LIABLE FOR SPECIAL INDIRECT INCI DENTAL OR CONSEQUENTIAL DAMAGES LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT WARRANT Y TORT NEGLIGENCE STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBIL ITY OF SUCH DAMAGES Further in no event shall the liability
17. e caution while using this product and complying with the following precautions could result in product malfunction and or void the warranty General Precautions e Read through the wet conditions maintenance procedures and make sure that you have all the tools you will need to properly maintain your vehicle e Not all batteries can be used in wet conditions Consult the battery manufacturer before use Do not use Li Po batteries in wet conditions e he included transmitter is not waterproof or water resistant If using a different transmitter than the one included consult your transmitter s manual or the manufacturer before operation e Never operate your transmitter or vehicle where lightning may be present e 00 not operate your vehicle where it could come in contact with salt water ocean water or water on salt covered roads contaminated or polluted water Salt water is very conductive and highly corrosive so use caution e Even minimal water contact can reduce the life of your motor if it has not been certified as water resistant or waterproof If the motor becomes excessively wet apply very light throttle until the water is mostly removed from the motor Running a wet motor at high speeds may rapidly damage the motor e Driving in wet conditions can reduce the life of the motor The additional resistance of operating in water causes excess strain Alter the gear ratio by using a smaller pinion or larger spur gear This will in
18. er and receiver too near large e Check the receiver antenna to be sure it is Loose or damaged wires or connectors e Replace recharge e Power On e Power On e Replace recharge e Replace recharge e Check tighten e Check repair replace e Move transmitter 8 12 feet 2 4 3 6m from receiver e Move away from large metal objects vehicles etc e transmitter and receiver e Contact Horizon Product Support e Make sure receiver antenna Is in an antenna tube and is above vehicle e Completely recharge battery e Do a check of the wires and connection between battery and receiver Repair or replace wires and or connectors Receiver loses its bind e Transmitter accidentally put in bind mode e Bind transmitter to receiver ending bind to receiver TORMENT 11 LIMITED WARRANTY What this Warranty Covers Horizon Hobby Inc Horizon warrants to the original purchaser that the product purchased the Product will be free from defects in materials and workmanship at the date of purchase What is Not Covered This warranty is not transferable and does not cover i cosmetic damage ii damage due to acts of God accident misuse abuse negligence commercial use or due to improper use installation operation or maintenance iii modification of or to any part of the Product iv attempted service by anyone other than a Horizon Hobby authorized service center v Product not purchased from an autho rize
19. g Officer International Operations and Risk Management TORMENT 13 lt PARTS DIAGRAM EXPLOSIONSZEICHNUNG VUE ECLATEE DES PIECES ESPLOSO DEL MODELLO CON REFERENZA PEZZI RECOMMENDED ITEMS EMPFOHLENE WERKZEUGE hi Qt 24 lt gt 0 SE Oo LLI ech F H D ok TORMENT 52 PARTS DIAGRAM EXPLOSIONSZEICHNUNG VUE CLAT E DES PI CES ESPLOSO DEL MODELLO CON REFERENZA PEZZI The slipper clutch can be adjusted using this locknut ECX1060 Fully tighten the locknut then loosen the nut two full turns Die Rutschkupplung kann durch diese otopmutter eingestellt werden ECX1060 Ziehen Sie die Mutter an und drehen Sie dann volle zwei Umdrehungen zur ck est possible d ajuster le sliper par ac tion sur cet crou de blocage ECX1060 Veillez serrer l crou de blocage fond Ensuite devissez l crou de trois tours complets La frizione pu essere regolata con questo dado autobloccante 1060 Prima avvitate completamente il dado poi svitatelo 2 giri When installing the wheel make sure the drive hex is aligned with the drive pin When the drive hex is removed the drive pin can fall out of the axle Bitte achten Sie bei der Radmontage darauf dass die Radachse im Radmitnehmer sitzt und dass der der Querstift nicht heraus f llt Lors de l installation de la roue assurez vous que l hexagone de roue est align avec la goupille d entra nement En cas
20. harged 1800mAh battery requires 0 9 hours 54 minutes to charge INITIAL CHARGE Your Dynamite peak voltage detection charger includes safety circuit ry and programming allowing the charger to stop charging after 15 minutes if it senses any issues that have come up in charging The high electrical resistance commonly found in new unconditioned Ni MH batteries can cause this safety circuit to activate turning the charger off before a full charging cycle is complete This is commonly known as a false peak in your battery charge should this occur during your first charge cycle it does not neces sarily indicate a failure of either your charger or battery Instead it shows that the charger 1 functioning properly and that the battery 1 not yet fully conditioned To complete your first full charging cycle in the event of a false peak restart the charger by pressing the Start button again Repeat this process until the charge cycle continues to charge past 15 minutes It may take as many as 2 to 4 restarts to complete your first one or two full charge cycles Once your charger completes a charge cycle longer than 15 minutes your battery will be fully charged A typical first full charge cycle should run for 45 to 90 minutes depending the self discharge condition of the battery since it was shipped from the factory Once your battery is properly conditioned through a few full charge and discharge cycles you will see normal ope
21. htet tanche CX13000 SEN Steering Lenkservo wasserdicht Servo de direction tanche CX231003 Battery Hold Down Akkuhalter ixation pour batterie CX4005 Front Bumper Set Vordere Stossstange eu de pare chocs avant Suspension Arm Jeu de renfort de CX2006 Mount Set Querlenker Set hinten suspension 14 ECX4003 md Wheel Rad montiert 2 Pneu mont jante 2 CX1015 Wheel Bearing Set Radlagersatz Set Jeu de roulement de roue CX1018 GE Suspension AIM querlenker Set vorne ECH bras de suspension Jeu de support Supporto ammortizzatori 17 ECX1020 Shock Tower Set Dampferbriicke aT richie eur posteriori X1035 ront Axle 2 Radachse vorne 2 Axe de roue avant 2 Mozzi ruota anteriori 2 X1044 inge Pin Set Querlenkerbolzen Set Jeu d axes de suspension Jeu de biellettes de Set tiranteria Camber e CX1046 Camber Link Set Spur Sturzstangenset 10 1 13 oupporti braccetti sosp Ruote e gomme montate 2 li Set cuscinetti ruote Braccetti delle sospensioni 16 anteriori 0 NIN miim m c CD CD C ct 2 Gc Mm 21 ECX1049 Wheel Pins 4 Radmitnehmerstifte 4 Goupilles d entra nement 4 Spine trascinatori ruote 4 ECX1060 M4 Locknut 4 M4 Stopmutter 4 Ecrous de roues 4 4 Dadi autobloccanti M4 4 ee Jeu de fus es avant et 23 ECX234000 Hu Un R dtr ger arri re avec triers portes d sterzo mozz
22. l space or indoors can cause overheating turning your transmitter off at low speeds Operating at low speed increases heat in the electronic speed control ESC Overheating can damage the vehicle and failure may result C F WHEN YOU ARE FINISHED 1 Power off the Electronic 2 Disconnect the battery 3 Power off the transmitter opeed Control ESC MOTOR CARE e Seat the motor brushes by driving smoothly on a flat surface starts pushing objects driving in deep water and tall grass during use of the first battery charge Failing to do so can and driving continuously up hill greatly reduce motor performance and functional life e ver temperature protection is installed on the ESC to e Prolong motor life by preventing overheating conditions prevent circuit damage but cannot protect the motor from Undue motor wear results from frequent turns stops and driving against heavy resistance 8 TORMENT MAINTENANCE SETTINGTHE GEAR MESH The gear mesh has already been set at the factory Setting the gear mesh is only necessary when changing motors or gears You must remove the vehicle s gear cover A to make this adjustment Proper gear mesh how the gear teeth meet is important to the performance of the vehicle When the gear mesh is too loose the spur gear could be damaged by the pinion gear of the motor If the mesh is too tight speed could be limited and the motor and ESC will overheat oet
23. le Tye service you in the event that you may need any assistance For ques tions or assistance please visit our website at www horizonhobby com submit a Product Support Inquiry or call 877 504 0233 toll free to speak to a Product Support representative Inspection or Services If this Product needs to be inspected or serviced and is compliant in the country you live and use the Product in please use the Horizon Online Service Request submission process found on our website or call Horizon to obtain a Return Merchandise Authorization RMA number Pack the Product securely using a shipping carton Please note that original boxes may be included but are not designed to withstand the rigors of shipping without additional protection Ship via a carrier that provides tracking and insurance for lost or damaged parcels as Horizon is not responsible for merchandise until it arrives and is accepted at our facility An Online Service Request is available at http www horizonhobby com content _service center_render service center If you do not have internet access please contact Horizon Product Support to obtain a RMA number along with instruc tions for submitting your product for service When calling Horizon you will be asked to provide your complete name street address email address and phone number where you can be reached during business hours When sending product into Horizon please include your RMA number a list of the included items
24. o fus es avant p Rear Suspension Arm Jeu de bras de suspension Braccetti delle sospensioni 0 Ensemble carter de Lee 25 ECX1021 Transmission Case Set Getriebegeh use oet scatola trasmissione 26 ECX232001 Rear Axle 2 Wellenmitnehmer hinten 2 Axe de roue arri re 2 0771 ruota anteriori 2 7 ECX232005 Driveshaft Pivot Ball 4 Antriebswellengelenk 4 roisillon de cardan 4 nodi semiassi 4 ECX232002 Driveshafts 2 Antriebswellen 2 ardan 2 emiasse 2 29 ECX1045 Hinge Pin Screws 8 Querlenkerbolzen Vis de fixation de renfort 8 Viti per perni sospensioni 8 Schrauben 8 30 DYN4925WP Regler ESC Variateur lectronique Variatore elettronico ESC otofsdm mpferkappen Bouchon piston et rotules oet tappi e pistoni 31 037 Shock Caps Pistons Kolben d amortisseur ammortizzatori 32 ECX1027 Gear Cover Getriebeabdeckung Carter de R ducteur Copertura per ingranaggi Couronne et pignons 33 ECX1022 Transmission Gear Set Getriebe interm diaires corps et et ingranaggi trasmissione pignons de diff rentiel olipper Clutch Plates Garnitures plateaux et Piattelli frizione disco 34 ECX1024 Pads Spring Rutschkupplung Teilesatz ressort de slipper e Arbre secondaire de 35 ECX1025 A Hauptgetriebewelle Set transmission avec goupilles ad Intermedio con d entra nement p 36 ECX1026 C Drive Getreibeausgangswelle 2 Ep d arbre de transmission Mozzi Differenziale 2 7 ECX1052 Washer Set Unterlegschei
25. ons found on our website http www horizonhobby com content service center render service center ATTENTION Horizon service is limited to Product compliant in the country of use and ownership If received a non com pliant Product will not be serviced Further the sender will be responsible for arranging return shipment of the un serviced Product through a carrier of the sender s choice and at the sender s expense Horizon will hold non compliant Product for a period of 60 days from notification after which it will be discarded Phone Number Email Address 877 504 0233 productsupport horizonhobby com 44 0 1279 641 097 sales horizonhobby co uk Harlow Essex CM18 7NS United Kingdom 12 TORNMENT Country of Purchase Horizon Hobby Germany Horizon Technischer Service Address Christian Junge Strake 1 49 0 4121 2655 100 25337 Elmshorn service horizonhobby de Germany Phone Number Email Address France Horizon Hobby SAS 11 Rue Georges Charpak 33 0 1 60 18 34 90 77127 Lieusaint France infofranceQhorizonhobby com 1 I H China Horizon Hobby China Room 506 No 97 Changshou Rd 86 021 5180 9868 shanghai China 200060 info horizonhobby com cn FCC INFORMATION This device complies with part 15 of the FCC rules Operation is sub ject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference
26. r off e Keep the wheels of the model off the ground when checking the operation of the radio equipment TABLE OF CONTENTS Safety Precautions and 5 2 AEN OI Mec 8 Water Resistant Vehicle When you are Finished 8 with Waterproof Electronics 3 Motor Care usn paret ri cariche naci nac nd 8 Specifications 3 Maintenance ENEE 9 4 Setting the Gear Mech g Vehicle Preparations Electone Speed Control ESC 9 Charging the Vehicle 4 Electrical Layout 9 Initial Charge nes 4 Shock Cleaning s 10 Baies 4 Fasteners tnn 10 Installing Transmitter 11 Transmitter Battery Safety Precautions 9 Troubleshooting 11 Removing the Vehicle Body Limited Warranty 12 Installing the Battery in the Vehicle SOMATA MA 12 6 ATTAT 13 RF Mode V m 6 IC 13
27. ration of the charger by a single press of the start button followed by a 60 to 90 minute charge cycle CHARGING WARNINGS A WARNING Failure to exercise caution while using this product and comply with the following warnings could result in product malfunction electrical issues excessive heat FIRE and ultimately injury and property damage e head all safety precautions and literature prior to use of this product Never leave the battery and charger unattended during use Never allow children under 14 years of age to charge battery packs Never attempt to charge dead or damaged batteries Never charge a battery if the cable has been pinched or shorted Never allow batteries or charger to come into contact with moisture at any time Never charge batteries in extremely hot or cold places recommended between 50 80 F 10 26 or place in direct sunlight Always use only Ni MH rechargeable batteries This charger cannot charge batteries such as heavy duty alkaline mercury or lithium battery Always connect to the charger correctly Always disconnect the battery and charger after charging and let them cool between charges Always inspect the battery before charging Always terminate all processes and contact Horizon Hobby if the product malfunctions Always make sure you know the specifications of the battery to be charged or discharged to ensure it meets the requirements of this charger Always constantly
28. sitions normally full brakes and straight steering If the receiver is turned on prior to turning on the transmitter the receiver will enter failsafe mode driving the servos to their preset failsafe positions When the transmitter is turned on normal control is resumed Failsafe servo positions are set during binding see binding a receiver above Solution short Run Time e Battery damaged not charged Check change battery e Motor dirty or brushes worn e Check clean replace Sluggish Action e Motor dirty or brushes worn e Bind in drivetrain e Vehicle battery is not charged Check clean replace e Clean adjust e Replace recharge Controls Reversed e ST REV or TH REV e Change switch position Motor ESC overheat Over geared for the driving environment e Install smaller pinion e Transmitter batteries low e Transmitter powered off e ESC powered off e Vehicle battery is not charged e Transmitter batteries low Doesn t Operate Poor Range e Transmitter antenna 15 damaged or loose e Receiver antenna damaged The system will not connect metal objects vehicles etc e Receiver accidentally put in bind mode so receiver is no longer bound The receiver goes into failsafe mode a short distance away from the transmitter The receiver quits re sponding during operation not cut or damaged ow battery voltage between battery and receiver e ransmitter and receiver too near each other e Transmitt
29. steering wheel and throttle trigger in the failsafe positions normally full brakes and straight steering see the Failsafe section on this page for more information press and hold the bind button and turn on the transmitter The green LED on the front of the transmitter will flash within three seconds indicating the transmitter is in bind mode 4 Release the bind button when the green LED flashes Continue to hold the steering wheel and throttle trigger in the failsafe positions until the LED on the receiver glows solid Bind Button TROUBLESHOOTING GUIDE Problem Possible Cause 5 The LED on the receiver will glow solid when the transmitter and receiver are bound 6 Remove the bind plug and store it in a convenient place You must rebind when e Different failsafe positions are desired e g when throttle or steering reversing has been changed e Changing receiver types e g changing from a DSM receiver to a DSM2 or Marine receiver e Binding the receiver to a different transmitter some Spektrum receivers like the SR3001 use bind button rather than a bind plug The binding process is the same with this receiver however instead of inserting the plug before powering up the receiver press and hold the bind button while powering up the receiver to enter bind mode FAILSAFE In the unlikely event that the radio link is lost during use the receiver will drive the servos to their preprogrammed failsafe po
30. the gear mesh by following these simple steps 3 Push the gears together while tightening the motor screws 1 Loosen the 2 motor screws B 4 Rotate the gears to remove the paper The gearing should 2 Put a small piece of paper C between the pinion and spur move a small amount gears 5 Reinstall the gear cover ELECTRONIC SPEED CONTROL ESC NOTICE The ESC DYN4925WP is compatible with NiCd and NiMH batteries only Not for use with LiPo or LiFe batteries Programming This is auotprogramming ESC The ESC auto programs each time the vehicle is turned on Operation LED Color LED Status Sound o Stop idee JON Forward AHO forward fullspeed Red JON Reverse Reverse full speed Green ON Broke ON Solid Green LED Red LED flashing once per second ELECTRICAL LAYOUT Part Description A A DYN1172 Motor c ee Ee O DYN1050EC Battery 7 2V SSS C ECX13000 Waterproof Steering WIT Servo 3 SPMSR201 a DYN4925WP_ Waterproof Electronic Speed Control ESC Channel 2 Tre For correct operation Channels 1 and 2 E must be used as shown in the wiring diagram 59 je 29 lt The motor can be disconnected from the ESC at the connectors in the wiring TORMENT 9 SHOCK CLEANING Oil filled shocks will require regular maintenance due to the oil breaking down or getting dirt
31. to motor for forward batteries or reverse see TH REV switch RF MODE The DX2E has a France Mode that complies with French STANDARD MODE DEFAULT PRESET SET AT FACTORY regulations The DAZE must be in France mode when used Turn the wheel full right pull the trigger full throttle and hold outdoors in France At all other times the transmitter should be down the bind button while turning on the transmitter The in Standard mode Green LED will flash once FRANCE MODE Turn the wheel full left pull the trigger full throttle and hold down the bind button while turning on the transmitter The Green LED will flash twice 6 TORMENT GETTING STARTED 1 Power on the transmitter 2 Power on the ESC 4 Start driving slowly and if the vehicle does not go 3 Do a test of the transmitter s control of the vehicle with adjust the steering trim dial on the transmitter 1 straight the vehicles wheels off the ground IMPORTANT Seat the motor brushes by driving smoothly on a flat surface during use of the first battery charge Properly seating the motor brushes will increase the life and performance of the motor INSTALLING THE VEHICLE BODY TORMENT OPERATION e ALWAYS turn on your transmitter before you turn on the e ALWAYS operate your vehicle in a wide open area Operating receiver in the vehicle Always power off the receiver before the vehicle in a smal
32. ury WARNING Procedures which if not properly followed create the probability of property damage collateral damage and serious injury OR create a high probability of superficial injury A WARNING Read the ENTIRE instruction manual to become familiar with the features of the product before operating Failure to operate the product correctly can result in damage to the product personal property and cause serious Injury This is a sophisticated hobby product and NOT a toy It must be operated with caution and common sense and requires some basic mechanical ability Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property This product is not intended for use by children without direct adult supervision Do not use with incompat ible components or alter this product in any way outside of the instructions provided by Horizon Hobby Inc This manual contains instructions for safety operation and maintenance It is essential to read and follow all the instructions and warnings in the manual prior to assembly setup or use in order to operate correctly and avoid damage or serious injury Age Recommendation Not for children under 14 years This is not a toy Safety Precautions and Warnings As the user of this product you are solely responsible for operat ing in a manner that does not endanger yourself and others or result in damage to the product or property of others
33. y This maintenance should be performed after about every 3 to 5 hours of use depending on the conditions that the vehicle is used in e Remove the shock from the vehicle REAR SHOCK ECX1037 lt ECX1043 sP ECX1057 ECX1043 c FRONT SHOCK ECX1037 Gr SCH WS 2 ECX1037 ECX1057 e Remove the cap from the shock body and dispose of fluid ECX1038 ECX1038 E e Disassemble the shock Clean thoroughly with DYN5505 Dry ECX1036 parts before assembly ECX1038 lt gt e he assemble the shock and refill the shock body with silicone ECX1043 Ji ECX1038 fluid 30 weight recommended ECX1037 ECX1043 e Slowly move the shaft and piston up and down to remove air ECX1037 bubbles e Move the piston to the midway point of the body and install 040 ECX1039 D the cap e Wipe off any overflowing fluid e When properly filled the piston should rebound about 3 8 in 9 5mm after being pushed in fully 1041 ECX1038 e Re install the shock on the vehicle 1038 Ride Height Adjustment Le Ride height is an adjustment that affects the way the vehicle ECX1037 oth we jumps turns and goes over bumps Drop one end of the vehicle from approximately 6 inches 152 mm in height onto a flat surface When dropping the front of the vehicle after the vehicle settles make sure the front arms are equal and parallel to the flat surface Do the same with the rear to
Download Pdf Manuals
Related Search