Tycon Systems UPS-ST2424-50-UBNT uninterruptible power supply (UPS)
Contents
1. Size 24V 270W Overcharge Protection Over discharge protection Over discharge recovery voltage Controller Self Consumption Operating Temperature e 48V 150W Power Supply Shielded POE Injector 10 Typical UPSPro ST2424 UBNT Application J p sul JOd S NI 30Od pue Ajddns u ZHO9 0S DVAOZZ OTT 49MOd MOST dH A8vSd J3 NOY JO YIUMS OL Auaneg Avz jaued JEIOS Avz Ja jOsUOD 0 NI 30d 9 S1V9D youms 07 INO JOd 9 S1Y2 S VST IGA T RES YIUMS 204 HOUN IN SMSS dL 40d Av 9 S1V9 11 Limited Warranty The UPSPro products are supplied with a limited 24 month warranty which covers material and workmanship defects This warranty does not cover the following 2 Parts requiring replacement due to improper installation misuse poor site conditions faulty power etc Lightning or weather damage Physical damage to the external amp internal parts Products that have been opened altered or defaced Water damage for units that were not mounted according to user manual Usage other than in accordance with instructions and the normal intended use D D D D Tycon Power Systems 14641 S 800 W Suite A Bluffdale UT 84065 support tyconpower com 8000025 Rev 3 UPS ST2424 UBNT UPSPro Qwik Install Guide 122. Solar input detects current from solar panel CHA ON Batteries are being charged from solar input If CHA is flashing it means batteries are fully charged LOA ON Battery voltage is sufficient and load outputs POE OUT and auxiliary wire terminal output are turned on REV ON Battery wires reversed Fuse The fuse is in line with battery power If fuse is blown there was some sort of short in the battery connection and the controller will appear dead Replace with 10A fuse 2 CAPACITY The UPSPro UPS ST2424 UBNT is rated at up to 60W power output If you exceed this load the system may not function to expectations Note The controller can supply 24V 1A from the POE OUT port and 24V 1 5A from the auxiliary wire terminal port To utilize the full 60W you can combine the outputs of both ports Power on the POE port is supplied on Ethernet pins 4 5 and 7 8 3 VENTING The enclosure is vented thru the wire feedthrus and vari ous hole plugs in the bottom of the enclosure Don t make these airtight with silicon 4 BATTERY MAINTENANCE The batteries used in the UPSPro sys tems don t require any maintenance They should last up to 5 years in normal use Note Never store batteries for any length of time in a dis charged state or it will kill the battery 5 BATTERY OVERDISCHARGE We highly recommend hooking all equipment loads to the controller voltage output This output will dis connect the load if the battery voltag
3. UPS S12424 UBNT Power UPSPro Backup Systems Power System a Wireless Base Stations and Client Devices gt Surveillance Cameras 2 Remote Sensors 2 UBNT Equipment a Microtik Equipment Congratulations on your purchase of the UPSPro outdoor backup power system Please take a moment to review this Qwik Install Guide before assembly or battery installation DANGER Avoid Powerlines You Can Be Killed When following the instructions in this guide take extreme care to avoid contact with overhead power lines lights and power circuits Contact with power lines lights or power circuits may be fatal We rec ommend to install no closer than 20 feet to any power lines Safety For your own protection follow these safety rules c Perform as many functions as possible on the ground o Do not attempt to install on a rainy windy or snowy day or if there is ice or snow accumulation at the install site or if the site is wet 2 Make sure there are no people pets etc below when you are working on a roof or ladder 2 Recommended Tools Phillips Screwdriver 13mm and 10mm Open End Wrench 8mm nut driver Flat Blade Screwdriv X Please help preserve the environment and return used batteries to an authorized depot Ren Qwik Install STEP 1 Add Grounding Wire Between Door and Enclosure Remove plastic covers on copper studs on inside of door and inside of enclosure Add jumper wire be tween 2 copper studs and use co
4. d due to vibration and the weight of the cables Be sure to add a zip tie or other method to hold the ca bles and relieve the cable weight from the connector STEP 12 If you have a solar panel route the solar panel cable from the solar panel thru one of the feedthrus on the bottom of the en closure and install to the SOL input of the controller Be sure to connect in the proper polarity red wire to and black wire to Make sure any outdoor connections are waterproofed STEP 13 Tighten all wire feedthrus If they don t tighten on a small diameter wire you can wrap some electrical tape around the wire in the seal area to increase its diameter and make a better seal The enclo sure needs some small amount of venting so be sure NOT to seal all holes and feedthrus with silicon STEP 14 Make sure lid gasket is clean and free from any parti cles then carefully close the cover making sure that wires are clear of the seam and hinge area Use the special key to close the two cover locks TECH CORNER Additional Information you may find useful 1 CONTROLLER The controller turns off power to the load at 22V and reconnects when the battery reaches 24V This protects battery from overdischarge and increases battery life and performance Controller LEDS POE ON POE input detects current from POE source If POE led is flashing it means the power source is too weak for the POE input Find a power source with more capacity SOL ON
5. e drops below 22V and this will protect the battery from over discharge If batteries get completely dis charged because the equipment was connected directly to the battery you will reduce the battery life and you will most likely need to super charge them with a good quality 10A automotive battery charger Once they are back to a normal operating range the integrated charge con troller will maintain the charge 6 WIND TURBINE A wind turbine can be added to this system at any time Wind Turbines are good sources of power often in times when the sun isn t shining like on stormy days We like to think of a wind tur bine as uptime insurance Tycon Power Systems offers small wind tur bines perfectly suited to augment the UPSPro systems The TPW 400 24 is a 400W 24V wind turbine To add a wind turbine it mounts to the inside diameter of a 41mm ID pole You will need to mount the control ler inside the enclosure and connect the output of the controller to the batteries The connection will be in parallel with the existing solar con troller connection 7 OTHER ACCESSORIES Tycon also offers a variety of voltage conversion products to meet almost any need Just visit tyconpow er com for more info Compatible Solar Panel Kits Tycon Power Systems Solar Panel kits come with High Performance solar panels side of pole mounts and out door rated connection cabling Solar panels have a 25 year output warranty Pole mounts and panels are desi
6. gned for wind loads to 9OMPH TPSK24 85W 24V 85W Solar Panel Pole Mount Cable TPSK24 120W 24V 120W Solar Panel Pole Mount Cable TPSK24 240W 24V 240W Solar Panel Pole Mount Cable Solar Kits Kits 6Hours Peak Sun Hours Peak Sun 3 Hours Peak Sun TPSK24 85W 20W continuous 10W continuous TPSK24 120W 30W continuous 15W continuous TPSK24 240W 60W continuous 30W continuous 8 Compatible Wind Turbine TPW 400DT 12 24 400W 12 24V Wind Turbine e Includes controller e Good low wind performance e Self braking in high wind e 80MPH survivability e Sealed and maintenance free 81mm Charge Controtier For Wind Turbine Nor for Lowe Alone 96mm 81mm Charge Current vs Windspeed 12V Type me 24y Type N Charge into 12V battery Ro o S Charge into 24V battery BS Oo D Windspeed m s 1m s approx 2knots Wind Speed RPM 400 12V 400 24V 4 7 mph 130 0 1A 0 1A 7 4 mph 200 0 5A 0 3A 8 9 mph 250 11 1 mph 300 14 5 mph 400 16 8 mph 450 22 4 mph 600 SPECIFICATIONS Subject change without notice 2 battery 20 hours Reserve Power 30W Load 4 battery 40 hours Battery Voltage DC e 2 battery 51Ah Battery Capacity 4 battery 102Ah Battery Type Valve EEN Lead Acid 24V Solar POE Charge Controller Controller Type POE and secondary outputs regulated Max Solar Panel
7. ng cable to proper length Observe proper polarity for all connections Note There are two V and two V GND connections on the controller and the switch You can use either connection The FG connection is for frame ground or earth ground If your grounding scheme requires it you can connect the FG to the enclosure ground point near the bottom of the door The FG is common to the RJ45 shield TP SCPOE Controller TP POE Switch FG GND 24V STEP 9 Install the batteries in the enclosure Batteries are 12V batteries and need to be connected in series for 24VDC output 24V two batteries and 24V four batteries configurations are shown here 4 STEP 10 If batteries are installed on their side make sure to apply an insu lator tothe top of the battery terminal to pre vent the battery terminals from shorting to the metal en closure in case the battery shifts inside the enclosure during an earthquake STEP 11 Disconnect the green front connector from the controller Connect the battery cables to the battery Be sure to observe polarity Black wire connects to battery negative terminal and BAT terminal on the controller After connecting the batteries plug the green connector into the controller When a fully charged battery is connected the Green LOA LED should light on controller and the LED s on the 5 port switch should power up Note green The con nector on the controller will become unplugge
8. pper washers and nuts to se cure STEP 2 Add wire feedthrus into the bottom connector plate Attach the connector plate to the bottom of the enclosure using self tapping screws provided STEP 3 Install hole plug in drain hole in bottom right corner of the en closure STEP 4 Mount the DIN rail to the door using screws provided Mount any extra equipment to the orange backplate and secure the backplate in the enclosure Note The DIN rail can also be mounted to the orange backplate or sides of enclosure if desired STEP 5 If pole mounting the enclo sure assemble the pole mount kit to the back of the enclosure and mount the en closure to a pole using the 6 hose clamps provided The enclosure can also be wall mounted using the 4 holes in the back of the en closure STEP 6 Insert the battery plat form in the bottom of the enclo sure The battery plat form has cutouts so wires can be routed un der the battery as need ed STEP 7 Attach the 3 green DIN Rail adapters to the charge con troller and 5 port POE switch using the screws provided Clip the controller and POE switch to the DIN rail STEP 8 Connect a two conductor wire be tween the back green connector on the con 3 gt gt S au oS troller to the back green connector on the 5 port switch You can use the included cable with terminal connectors by cutting off terminal con nectors and then cutting and strippi
Download Pdf Manuals
Related Search