INSTEON 2842-222 multimedia motion sensor
Contents
1. s ability to detect motion Mount Sensor 1 2 3 4 Use the two small screws included to secure the swivel mounting bracket at your desired location Slide Motion Sensor onto the swivel mounting bracket sliding the unit to the right until you hear a click Aim Motion Sensor towards the area in which you wish to detect motion Test by walking through the area Responder s should respond appropriately when motion is sensed and turn off 30 seconds after last motion sensed 2452 222 2452 422 2452 522 Rev 11 6 2012 1 27 PM See Owner s Manual for Warranty Information Protected under U S and foreign patents see www insteon com N S F N Copyright 2012 INSTEON 16542 Millikan Ave Irvine CA 92606 800 762 7845 Adjust Detection Area 1 Tap the Set button on Motion Sensor until the linked responder s turn off 2 Within 10 seconds walk well out of detection area 3 Wait 20 seconds 4 Walk into and near your detection area Your linked responders will turn on LED will flash upon initial motion then once every 8 seconds during motion a If LED does not flash while you are moving within the desired detection area re aim sensor usually means pointing the Sensor up b If LED flashes while you re moving outside detection area i Aim sensor to decrease range usually means aiming the sensor down li If aiming sensor does not generate desired results place jumper 1 on both pins see section2. Setup Modes Setup Modes Optional Set Jumpers Jumpers are small plastic boxes that act as a switch When installed on 2 pins the switch is on When installed on 1 pin or missing the switch is off Jumper 1 Sensitivity To reduce sensor s detection range by approximately 33 use needle nose pliers to carefully remove Jumper 1 the left most jumper from the single pin it is installed on and reinstall it on both pins Tap the set button once wait 10 seconds and activate motion to establish the new setting Jumper 2 Disable LED If you wish to disable the LED it will still operate during setup install Jumper 2 on both pins Tap the set button once wait 10 seconds and activate motion to establish the new setting Jumper 3 Night Only Mode If you wish to have the Sensor operate only when dark install Jumper 3 on both pins Tap the Set button once wait 10 seconds and activate motion to establish the new setting Note It takes 3 5 minutes or 7 Set button taps to detect the difference between day and night See Day Night Threshold below for details Jumper 4 On Only Mode If you wish to disable the automatic off countdown install jumper 4 on both pins and the Motion Sensor will only send On Tap the Set button once wait 10 seconds and activate motion to establish the new setting Jumper 5 Remote Software Management If you wish to manage all of sensors settings via INSTEON software s
3. a small Phillips screwdriver to remove screw and cover from battery compartment on back of unit Attach the included 9V battery Do not replace compartment cover until instructed to do so later in this manual Wait 5 minutes for the circuit to stabilize Then to confirm unit is functioning tap the Set button a couple of times while watching the front of the unit Each time you tap the Set button a red LED behind the sensor lens will flash Don t worry if the LED flashes when you are not tapping the Set button it is simply indicating that motion is being detected Close up of battery compartment Dual Band Products and Access Points If you want Motion Sensor to control a powerline only device you need at least one INSTEON Access Point 2443 or other dual band product installed in your home Make Motion Sensor a Controller 1 Press and hold the set button on Motion Sensor for 5 seconds Motion Sensor LED behind sensor lens will start blinking red 2 Turn responder on or any other state such as on 50 or even off 3 Press and hold responder set button until it double beeps Motion Sensor LED will stop blinking 4 Test by tapping Motion Sensor set button Responder load will respond appropriately Motion Sensor LED will blink red 5 Repeat steps 1 4 for up to 32 responders you wish Motion Sensor to control 2452 222 2452 422 2452 522 Rev 11 6 2012 1 27 PM See Owner s Manual for Warranty Information Protected under U S and f
4. low sensor needs to be able to distinguish between what is being sensed and its surroundings d See Placement Tips section LED is double Low battery warning replace with fresh battery flashing upon motion Remove Motion Sensor as a Controller 1 Press and hold the set button on Motion Sensor for 5 seconds Motion Sensor LED behind sensor lens will start blinking red 2 Press and hold the set button on Motion Sensor for 5 seconds Motion Sensor LED will continue blinking red 3 Press and hold the responder set button until it beeps Motion Sensor LED will stop blinking 4 Test by tapping the set button on Motion Sensor Former responder will not respond Factory Reset Return Motion Sensor to Factory Settings 1 If possible remove Motion Sensor as a controller of all responders before proceeding 2 Remove battery 3 Wait 15 seconds 4 While pressing the set button reattach the battery After about 2 seconds the LED will turn on Continue pressing the set button for 5 seconds and then release the set button The LED will turn off after about 2 seconds o1 If you do not unlink your responder will to continue to respond to Motion Sensor even after factory reset procedure is complete Owner s Manual and Tech Support For the most up to date Quick Start Guide visit http Awww insteon com support Call INSTEON Support Line at 866 243 8022 FCC and IC Warnings This device complies with FCC Rules and Industry Canada license ex
5. will flash on first motion but it will not turn on its linked responders Troubleshooting Symptom Resolution Sensor won t link to Move a dual band INSTEON device e g Access Point closer to the Motion Sensor responders 2452 222 2452 422 2452 522 Rev 11 6 2012 1 27 PM See Owner s Manual for Warranty Information Protected under U S and foreign patents see www insteon com N S E N Copyright 2012 INSTEON 16542 Millikan Ave Irvine CA 92606 800 762 7845 Make sure LED flashes to confirm it has power and is sensing motion Sensor is in night only mode and it is day Move a dual band INSTEON device e g Access Point closer to the Motion Sensor Sensor is in its 1 minute countdown Sensor won t control a linked responders b C d LED flashing rapidly Sensor did not receive an acknowledgement from one or more linked devices If this occurs after motion is repeatedly you may need to move a dual band INSTEON device closer to the Sensor or you may detected need to unlink a device which is no longer in use in your home If the INSTEON responders are no longer available you may either use software or perform a factory reset to remove the unwanted links LED not flashing a You may need to wait up to 8 seconds to see the flash upon motion b Battery may need to be replaced Not sensing motion a Light detected and unit is in night only mode b Motion Sensor aimed too low c Temperature too high or
6. Quick Start Guide INSTEON Motion Sensor Models 2842 222 2842 422 2842 522 Tools Needed e Small Phillips screwdriver LED i illip wdriv Introduction The INSTEON Motion Sensor is an indoor outdoor motion sensor that will turn INSTEON controlled lights on and off in response to movement around your home The sensor also contains a photocell allowing you to configure the unit to only turn your lights on at night Pair the Motion Sensor with INSTEON software for almost limitless automation possibilities In this package you will find the Motion Sensor a 9V battery a swivel mount and 2 SCrews Operation When Motion is Sensed 1 When motion is sensed the Motion Sensor will send an ON command to up to 30 linked INSTEON responders and flash its LED unless it is daytime and unit is in night only mode 2 Sensor will begin its automatic countdown 3 Whenever motion is sensed during countdown the countdown will be reset to easily allow you to create occupied versus unoccupied modes for your home 4 When countdown expires the Sensor will send an OFF command to all linked responders unless it is in on only mode Applications e Turn on driveway or front step lights when visitors approach e Have your fountain always on when you are around and off when you are away e Save money by having HVAC and lighting automatically go into energy saving mode when no one is around Setup Insert Battery Set button Use
7. empt RSS standard s Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference including interference that may cause undesired operation of the device Le present appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence L exploitation est autorise aux deux conditions suivantes 1 l appareil ne doit pas produire de brouillage et 2 l utilisateur de l appareil doit accepter tout brouillage radiolectrique subi mme si le brouillage est susceptible d en compromettre le fonctionnement CAUTION To reduce the risk of overheating and possible damage to other equipment do not install to control a receptacle a motor operated appliance a fluorescent lighting fixture or a transformer supplied appliance Gradateurs commandant une lampe a filament de tungstene afin de reduire le risqu de surchauffe et la possibilite d endommagement a d autres materiels ne pas installer pour commader une prise un appareil a moteur une lampe fluorescente ou un appareil alimente par un transformateur 2452 222 2452 422 2452 522 Rev 11 6 2012 1 27 PM See Owner s Manual for Warranty Information Protected under U S and foreign patents see www insteon com N S F N Copyright 2012 INSTEON 16542 Millikan Ave Irvine CA 92606 800 762 7845
8. oreign patents see www insteon com N S E N Copyright 2012 INSTEON 16542 Millikan Ave Irvine CA 92606 800 762 7845 Detecting Area DETECT NG AREA Unit Meter 70 1 gt ee A 012 3 4 5 6 7 8 9 0 228M LENGTH 12M 0123456789 101112135 Placement Tips Select a location that will provide the coverage required while keeping in mind the following potential problems Reflective surfaces Do not aim the detector at reflective surfaces such as mirrors or windows as this may distort the coverage pattern or reflect sunlight directly onto the detector Air flow Avoid locations that are subject to direct high air flow such as near an air duct outlet Moisture Do not place the detector near sources of steam or oil Sunlight Do not aim the detector such that it will receive direct or reflected mirror sunlight Obstruction Do not limit the coverage with large objects within the detection area such as plants or filing cabinets Pet rejection Do not aim the detector at a stairway which a pet has access to and do not place furniture or objects higher than 3 ft 0 9 m which a pet can climb onto e g a cat on a couch closer than 6 ft 1 8 m to the detector Fireplace Do not place the detector near a fireplace due to the light and heat Snow or ice Snow or ice on the Fresnel lens may interfere with Motion Sensor s ability to detect motion Dirt Dirt on the Fresnel lens may interfere with Motion Sensor
9. uch as HouseLinc install jumper 5 on both pins Then follow your INSTEON software instructions for managing sensor Adjust Modes Adjust Dials Left Dial Adjust Automatic Off Countdown Using a small Phillips screwdriver adjust to the desired time duration in which you want Motion Sensor to send an OFF command after the last motion sensed Turning the dial all the way counter clockwise sets the countdown to 30 seconds turning the dial all the way clockwise sets it to 2 hours Anywhere in between results in a proportional difference between 30 seconds and 2 hours Right Dial Day Night Threshold Using a small Phillips screwdriver adjust the day night threshold to desired light level Turning the dial clockwise increases the light level of the threshold turning the dial counter clockwise decreases the light level of the threshold For example when you turn the dial all the way clockwise Motion Sensor will read night no matter how bright it is Likewise turning the dial all the way counter clockwise will make Motion Sensor read day no matter how dark it is Turning the dial anywhere in between will choose the specific light level which Motion Sensor uses to determine night vs day To test set Motion Sensor to night only mode see above and tap the set button 7 times If it reads the current light level as night it will turn on its linked responders on first sensed motion If it reads day the LED
Download Pdf Manuals
Related Search