Chief KRA225B mounting kit
Contents
1. INSTALLATION 2 Use 5 16 18 x 3 button head cap screw D two thin steel washers H plastic washer J pivot pin G pivot pin spacer C and 5 16 18 lock nut F to secure KRA225 1 Remove button head cap screw spacers pivot pin and lock p p head assembly to Kontour mount See Figure 2 nut to disassemble head from K2 mounting arm See SUME NOTE Cable clip B can be used in place of pivot point spacer C if additional cable management is desired See K2W110 shown Figure 2 as example 1 S K2W110 shown as example K2W110 arm Figure 1 Figure 2 KRA225 Installation Instructions Display Installation 1 Remove quick release faceplate from mount by pulling quick release lever and sliding faceplate off mount See Figure 3 For recessed mounting hole installation e Place four spacers on top of mounting holes on back of display See Figure 5 Using Phillips screwdriver carefully install four M4x25mm screws through corresponding holes on faceplate spacers and into the mounting holes on the display See Figure 5 Figure 3 2 Carefully place display face down on protective surface NOTE Use display mounting hardware included with K2 Series mount to attach display to KRA225 faceplate 3 Connect faceplate to display For flush mounting hole installation Using Phillips screwdriver carefully install four M4x14mm screws through corr2. INSTALLATION INSTRUCTIONS K1 Extreme Tilt Head Accessory KRA225 CHIEF Vision Our Mounts Your KRA225 Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief and Kontour are registered trademarks of Milestone Technologies All rights reserved IMPORTANT SAFETY INSTRUCTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warranty I
3. esponding holes on faceplate and into the mounting holes on the display See Figure 4 for recessed mounting holes T gt quick release faceplate M4x25mm x4 spacers x 47 for flush mounting holes quick release faceplate oQ M4x14mm x4 Figure 4 Figure 5 4 Position display with faceplate attached above mount See Figure 6 5 Slide faceplate onto mounting head until quick release tab clicks into place See Figure 6 2d Figure 6 Installation Instructions KRA225 Adjustments Pitch Adjustment 1 Adjust pitch to desired tilt position See Figure 7 2 Adjust pitch tension screw to change the adjustment tension See Figure 7 Pivot Adjustment 3 Adjust pivot position as desired See Figure 7 4 Use 3 16 hex key to adjust pivot point tension screws to change pivot adjustment tension See Figure 7 Rotational tension pivot point tension tension Figure 7 Rotational Adjustment NOTE Optional Rotational adjustment may be locked by installing rotational locking screw E into back of faceplate See Figure 8 Figure 8 5 The monitor may be adjusted 90 degrees in either direction in order to provide a portrait view of the monitor See Figure 7 6 Use 3 16 hex key K to adjust rotational adjustment screw to adjust rotatio
4. nal tension See Figure 7 Display Removal WARNING Only remove display from mount when the display can be lifted up from the mount DO NOT remove display unless the display is in the upright position See Figure 9 1 Make sure display is in the upright position 2 Remove quick release faceplate from mount by pulling quick release lever and sliding faceplate off mount See Figure 9 quick release tab Figure 9 KRA225 Installation Instructions Installation Instructions KRA225 KRA225 Installation Instructions USA International CHIEF Our Mounts Your Vision Europe Chief a products division of Milestone AV Technologies Asia Pacific 8800 002497 Rev00 2014 Milestone AV Technologies www chiefmfg com 03 14 gt 6436 City West Parkway Eden Prairie 55344 800 582 6480 952 225 6000 877 894 6918 952 894 6918 Franklinstraat 14 6003 DK Weert Netherlands 31 0 495 580 852 31 0 495 580 845 Office No 918 on 9 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477
5. t is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components located attached to the KRA225 tilt head accessory up to and including the display does not exceed the weight limit listed for the mount to which it is attached Use with products heavier than the maximum weight indicated may result in collapse of the mount and its accessories causing possible injury WARNING Use this mounting system only for its intended use as described in these instructions Do not use attachments not recommended by the manufacturer WARNING Never operate this mounting system if it is damaged Return the mounting system to a service center for examination and repair WARNING Do not use this product outdoors SAVE THESE INSTRUCTIONS INTERFACE ROTATION RANGE 0 TING PATT 100 1 100 151 13 Installation Instructions KRA225 TOOLS PARTS FOR INSTALLATION UM 10 1 4 1 8 included se 18 clip IL 2 mm 4 9 Thin ui washer J 1 3 ie KRA225 head Pivot pin washer e accessory C 1 ASSEMBLY AND
Download Pdf Manuals
Related Search