Elite Screens SableFrame 2 100"
Contents
1. ezFrame 2 amp Sable Frame 2 Series Fixed Frame Projection Screen User s Guide Thank you for choosing an Elite Screens fixed frame projection screen Please read through this user guide before utilizing the screen Correct usage and maintenance will ensure a long product life Care amp Use Instructions Dust dirt and scratches on the projection surface will affect the picture quality please take note of the points below to prevent that from occurring 1 Do not touch the projection surface with your hands 2 Do not write or draw on the projection surface 3 Do not use fingers or sharp objects to point on the projection surface this will damage the screen material 4 Use a soft damp cloth to clean the projection surface do not use chemical cleaning agents or alcohol 5 Use clean water when dampening the cleaning cloth and do not rub against the material to clean it Hardware and Parts List A Frame Parts B Screen Material C Center joints D Elbow Joints E Wall brackets F Wood Screws G Drywall anchors H M5x15 screws I Center Support Bar J Support joiner K Fix Plates L Rubber hammer M Screw driver x 6 pcs 4 top bottom frame pcs 2 side frame pcs x l pc X 2 pcs x4 pcs x4 pcs depending on model size x 8 pcs x 8 pcs x 16 pcs x 1 2 pcs depending on model size x 2 4 pcs depending on model size x 60 180 pcs depending on model size x l pe x l pc2. 1 is about 10cm away from the frame s corner Fix plate 2 is about 5cm away Fig 7 Fig 7 Rev 081914 JA www elitescreens com 4 Tip for attaching the last corner D 1 Position yourself left of location Q 2 Pull the material to the corner of the frame with your hand while your left hand snaps in the fix plate on location the third red dot 3 Then insert and snap in the fix plate on location 4 Next move and position yourself on location 8 then pull the edge to the frame and fasten plates on locations and 5 Finally fasten the last fix plate on location Fig 8 E Fig 9 5 Next fasten a fix plate on the center of each frame side in the following order IL gt J gt K gt L gt M gt N gt 0 gt P as shown in Fig 10 Fig 10 Fig 11 Rev 081914 JA www elitescreens com 5 Black backing for AcousticPro models This procedure only applies to AcousticPro models Disregard this section if your Fixed Frame does not include an acoustically transparent screen material The purpose of the black backing material 1s to block out any light penetration that may reflect off of anything mounted behind the screen which can cause distortion to the projected image i The black backing is held in place by the Velcro that is on the fix plates Black backing Fix plates secure the Acoustic material and the black backing behind it ecthomeninememronmncmetin wf o
3. Note Please make sure all parts are included in your package before proceeding to assemble your fixed frame projection screen Rev 081914 JA www elitescreens com 1 FRAME ASSEMBLY 1 Insert the center joint c connector to the 1 2 horizontal frame piece and fasten it with two M5x15 screws h M5x15 Screw Y Long Frame 2 Insert the other 1 2 horizontal frame piece to the center joint c connector and fasten it with two M5xI15 screws h Repeat steps 1 and 2 for assembling the second horizontal frame iz Ta Horizontal Long Frame Note a Two size horizontal frames should be assembled for a screen b Do not tighten the screws completely until all frame pieces have been assembled correctly 3 Insert both elbow joint d connectors into the long horizontal frame and fasten it with two M5x15 screws h see Fig 1 Then insert the vertical short frames into the exposed elbow joint d connectors and fasten them with M5x15 screws fig 1 2 Long frame Fig 1 1 Rev 081914 JA www elitescreens com Short frame Fig 1 2 4 Join all four frame parts together following the steps shown below Fig 2 Note When assembled please push simultaneously the two ends of the long frames Insert
4. ctions carefully to ensure proper maintenance and safety of your Fixed Frame Screen 1 When hanging the screen up please make sure that no other objects such as power switches outlets furniture ladders windows etc occupy the space designated for your Fixed Frame screen 2 Regardless if the screen is hung on or installed into the wall make sure that the proper mounting anchors are used and that the weight is supported appropriately by a strong and structurally sound surface just as any large and heavy picture frame should Please consult a home improvement specialist for the best advice on installation 3 Frame parts are made of high quality velour surfaced aluminum and should be handled with care 4 When not in use cover over the screen with a furniture sheet to protect it from dirt grime paint or any other impurities 5 When cleaning use a damp soft cloth with warm water to remove any marks on the frame or screen surface 6 Never attempt to use any solutions chemicals or abrasive cleaners on the screen surface 7 In order to avoid damaging the screen avoid touching it directly with your fingers tools or any other sharp or abrasive objects 8 Spare Parts should be placed out of reach of small children in accordance with household safety guidelines For a local Elite Screens contact or Technical Support please visit www elitescreens com Rev 081914 JA www elitescreens com
5. e E Interval markings reveal the best points for inserting the fix plates Fig i RRR a Mae a 12 The prongs on the fix plates insert to the lip on the back of the es PRn i frame creating a friction hold that will firmly keep the material and black backing in place Fig 13 14 After the material has been installed the backing will lay over the back of the white Acoustic material and then be held in place by the Velcro on the fix plates Fig 15 Fig 12 f Center Support Bar 1 Insert the support joiner j into each end of the center support bar i Center support bar a v 2 Insert the Center Support Bar into the upper top groove on the back of the frame not the one where the fix plate inserts with the bottom end near the approximate center point of the frame and rotate it in at an angle so that both ends of the bar are in alignment with the groove see Fig 16and Fig 17 below for details Diagonal models 135 and below use 1 x Center Support Bar Center Support Bar _ Fixed plate groove Ran do not insert here Center polnt Fig 16 Screen material edge Rev 081914 JA www elitescreens com 6 Diagonal models above 135 require 2x Center Support Bars Center point Center point Fig 17 3 Slide the top end of the bar into the top center point of the frame to complete the center support bar installation This will provide added stability to your frame and added tension to
6. the exposed ends of the joint connectors into the short vertical frame and align the four corners so that they meet at perfect right angles Rev 081914 JA www elitescreens com Attaching the screen material to the frame 1 Make sure the screen material and frame are both lying face down on a clean dry and non abrasive surface 2 Carefully unroll the material inside the frame Fig 3 Please note the material will be noticeably smaller than the frame as the material must be stretched to create a sufficient amount of tension for perfect material flatness Notes Make note of the label to help distinguish the back and front side Unroll the screen material face down Fig 3 Keep the screen material as close as possible to the frame and do not allow it to scratch against any part of the frame 3 Attach the fix plates 1 Stretch the material to the corner and insert the screen material s edge in the groove of the frame While one hand holds the material in place the other hand snaps in the push plate Fig 4 Fig 5 Insert push plate in Fig 5 he Schematic cross section Plate AN of the frame A Frame groove Screen material edge 2 Begin by securing the four corners in the following sequence A B C D Fig 6 3 Insert the fix the plates as shown on Fig 5 Fix plate
7. the material Installation 1 Locate your desired installation location with a stud finder recommended and mark the drill hole area of where the screen is to be installed 2 Drill a hole with the proper bit size according to the wood screws included 3 Line up the wall brackets with the drilled holes on the installation location and screw them in using a Phillips screwdriver Note Use 2 top wall brackets on diagonal sizes below 135 and use 3 top wall brackets on diagonal sizes 135 and above 4 Position the fixed frame screen onto the top wall brackets as shown in Fig 18 and push down at the center of the bottom frame to secure the installation 5 The design of the wall brackets allows the frame to slide over them through its sides This is an important feature of the installation design as it allows your screen to be properly centered 6 Using both hands finish the installation by pushing the lower portion of the fixed frame screen into the lower bracket as shown in Fig 19 y F miam a Fig 18 T Fig 19 eee AA a Io ae oe a aa rea oe ea Pe re neesan ve oS a 24 2H ie Tr a p E eH LA T I 7 I Sh ZI L Ta T 5 ae T ae C pui H I I rae T ro L 4 or E T eTe E os He xir fal LA A ge oi n i a fake ee ete tio vad I aaa E ga Rev 081914 JA www elitescreens com 7 Please follow these instru
Download Pdf Manuals
Related Search