EZ Dupe BRPIOB2
Contents
1. 9 6 Delete Image Deletes the image s from the HDD and reclaims the space occupied by the image on the HDD gt Press ST gt Select the image file gt to be deleted gt J Press gt Delete Image RE es 9 7 Show HDD Info Shows the amount of used and free images available on the HDD in both CD and DVD formats 9 8 Format HDD Deletes and formats all image s on the HDD restores the HDD to factory defaults and initializes the HDD for use with the duplicator gt Press again formatting gt gt Press ENT ENT to confirm format gt Basic Troubleshooting Follow these simple steps for quick and proper troubleshooting 1 Power does not turn on or unit receives no power a Check power cord and outlet to make sure power connections are secured b Check voltage switch on the back of the duplicator to make sure power supply is set for correct outlet rating c Test with another power cord same as a PC power cord to eliminate cable failure 2 Master disc cannot be read a Change the master disc The master disc may be of poor quality or with error s that can make duplication difficult or impossible 17 b C d Remake the master disc on another disc Master disc may be of poor quality or with error s that make duplication difficult or impossible Change the source drive to one of the other drives to test Make sure the master disc is finalized in standard ISO format High failure rate2. 11 targets from one single master disc Operating Environment Working Temperature 0 75 C E Storage Temperature 20 C 85 C Humidity Working Humidity 20 80 Storage Humidity 5 95 LCD Front Panel Overview Scroll Button UP ENT Button ENTER DG LCD Screen v ESC Button ESCAPE Control Buttons There are 4 control buttons A el Scroll Button DOWN Up Backward To navigate backward in the menu Down Forward To navigate forward in the menu ENT Enter OK Execute the function ESC Escape Cancel Go back to the previous level in the menu Menu Overview Below is a quick reference chart of the functions available on SATA CD DVD Blu ray Duplicators Power on the system to access the menu functions below COPY Copies the master CD DVD Blu ray All contents of the master disc will be duplicated on to all target disc s simultaneously TEST Simulates the copy process but no data is recorded onto the blank disc s Note Test mode can only be done with DVD R and CD R media only COMPARE Performs a bit for bit comparison between the master disc and copied disc s COPY amp COMPARE Copies the master CD DVD Blu ray and then immediately follows the copy process with a bit for bit comparison between the master disc and copied disc s to ensure exact duplication Note The Compare function cannot be used with audio CDs D SET BURN SPEED Allows the speed settings to be changed for v
3. Setup is hidden within the Setup Menu step 11 To access Advanced Setup navigate to Setup Menu then press and hold down the scroll buttons simultaneously until the menu stop looping 8 9 1 Power On Time Set the amount of time the duplicator counts down before initializing the system The default is 15 seconds The time can be set from 5 to 99 seconds in 1 second increments 5 6 7 97 98 99 gt gt Alor v to select gt confirm 13 8 9 2 Start up Menu Sets the command to be displayed first when the machine is powered up and initialized All primary commands are available to be set for Start up Copy Test Copy amp Verify Copy amp Compare etc ei gt Ajor y to select gt confirm 8 9 3 Skip Read Error Allows the duplicator to skip uncorrectable read errors on the master DVD or CD or Blu ray This feature can be turned ON or OFF 8 9 4 Change Bad Master Allows the changing of the master disc during duplication when there is an uncorrectable error on the master disc s that threatens to disrupt the copy process 8 9 5 CD Overburn Allows the copying of CDs that have been burned over their maximum capacity The target disc s must be the same capacity as the master disc gt Press gt Aj or v to select mode and gt press ENT to confirm 8 9 6 Show HDD Image Allows the option to display the name of the HDD image name default or the image size in MB gt A or v to select
4. onto all target discs 7 4 2 Close Disc Closes the target discs when all of the track s are burned on to all target discs Note The copied disc s will NOT play back without this step Do NOT skip this step 7 4 3 Disc Info Checks the capacity and space used on the disc s inside of the drive s of the duplicator 10 7 5 Eject All Discs Performs a simultaneous ejection of all of the optical disk drive s on the duplicator ee gt Press gt All disc trays will open 7 6 Copy Counter Tracks the numbers of successful and failed copies made by the duplicator for both CDs and DVDs There are three 3 parts of this tool Show Count to display current copy counter Enable Counter to turn the counter on or off and Reset Counter to clear counter 7 6 1 Show Counter gt Press Press gt gt 7 6 2 Enable Counter 3 Say gt A or v and press to select choice 7 6 3 Clear Counter gt gt Press Press T rare n m gt gt gt Press to confirm or press to cancel gt 7 7 Update BIOS Updates the BIOS firmware of the duplicator gt Insert update CD gt anm mo ir Setup This command contains options to configure the duplicator system Update completed and eject disc gt 8 1 Auto Start Time Set the amount of time before the duplicator will automatically start the selected command ranging from OFF no auto start to 99 seconds in 1 second increments 1 2 3
5. the reader speed for the duplicator to read the master disc s The speeds for CD are 1 2 4 8 10 12 16 20 24 32 36 40 44 48 52 56 default MAX The speeds for DVD are 1 2 2 4 4 6 8 10 12 16 18 20 default MAX de gt Lal or v to select CD Read and press gt gt gt A or v to select DVD read speed and press ENT to finish 8 6 Compare Speed Sets the speed at which the master disc is compared with the copies disc s The speeds for CD are 1 2 4 8 10 12 16 20 24 32 36 40 default 44 48 52 56 MAX The speeds for DVD are 1 2 2 4 4 6 8 12 16 default 18 20 MAX Compare Speed and press gt gt A or v to select DVD Compare and press ENT to finish 8 7 Language Sets the language selection of the display Available languages are English default Soanish Portuguese and Japanese gt Press gt A or y to select gt ae language and press ENT to confirm gt A or v to select CD 8 8 Clear Setup Resets the duplicator back to factory default settings Press confirm gt aa gt Press ENT to clear all settings 8 9 ADVANCED SETUP This menu is for the more advanced functions of the duplicator including changing the duplicator display updating writer drive s of specific brands setting the loop and time parameters for the burn in process to test the machine and performing firmware rollbacks to earlier versions Note The Advanced
6. 97 98 99 11 2 gt press gt A or v to select seconds and press ENT to confirm 8 2 Display Mode Changes the display readout during the performance of various commands 2 gt ress gt A or v to select mode and press ENT to confirm 8 2 1 Basic The Basic mode displays a progress bar along with the amount of total data in MB on the master DVD or in time for the master CD 8 2 2 Show Timer Allows the display of total time taken for the copy process to be complete 8 2 3 Show Speed Displays the speed at which discs are read and writing during various processes gt A or v to select mode and press ENT to confirm 8 3 Button Beep Turns the audio signal a beeping sound ON or OFF for pressing of the buttons SEN gt A or N to select mode and press ENT to confirm 8 4 Eject On Start Allows the drive s with disc s present inside to eject the disc trays when the machine is done initializing gt Alor v to select Eject All gt Press Ee ae No Eject Eject Target Eject gt Source and press ENT to confirm 8 4 1 Eject All Discs Performs a simultaneous ejection of all of the optical disk drive s on the duplicator eo gt Press gt All disc trays will open 8 4 2 Do Not Eject Do not eject any disc 8 4 3 Eject Target Only Eject writer drive only 8 4 4 Eject Source Only Eject reader drive only 12 8 4 5 Eject All Trays Eject all drives 8 5 Reader Speed Sets
7. Blu ray DVD CD Duplicator Manual User s Manual Version 3 0 TABLE OF CONTENTS e HDD Introduction 2 e Setup 11 Manager 15 LCD Front Panel o Select Overview 2 o Auto Start Time 11 Image 15 e i o Disc gt Menu Overview 3 5 o Display Mode 12 Image 16 o Set Functions 6 o Button Beep 12 Reader 16 Speed o Show e Copy 6 o Eject on Start 12 Image 16 Info o Rename e Test 6 o Reader Speed 13 Image 16 o Delete e Compare 7 o Compare Speed 13 Image 17 Sh e Copy Comp 7 Language 13 S DD E 17 e Set Burn Speed 8 Clear Setup 13 gt e S 17 e Select Source 9 e Advanced Setup 13 e Utility Power On Time 13 o Information Start Up Menu 14 o Erase Disc 10 Skip Read Error 14 o Prescan 10 Change Bad Master 14 o Track Edit 10 CD Overburn 14 14 Basic o Eject All Disc 11 Show HDD Image Name Troubleshooting 17 18 o Copy Counter 11 Keep Buffer 14 14 Specification of 19 o Update BIOS 11 Boot Password SATA Duplicator Setup Password 15 Introduction Thank you for purchasing a SATA CD DVD Blu ray Duplicator This duplicator is specifically engineered to run a stand alone SATA CD DVD Blu ray duplicator without additional computer or processing unit With a simple four button interface and a LCD screen to display menu commands and real time status the SATA CD DVD Blu ray Duplicator provides a fast and reliable solution for CD DVD and Blu ray duplication up to
8. Do not eject any disc 8 8 Clear Setup Clears the CMOS and resets the duplicator back to factory defaults 8 9 ADVANCED SETUP 8 9 1 Power On Time Sets system warm up time from 5 sec to 99 sec Default is 15 seconds 8 9 2 Startup Menu Assigns a command to be displayed first after the duplicator has been initialized 8 9 3 Skip Read Error Enables the option to halt the duplication process if there is an error on the master disc Disables the option to allow the process to continue with the same errors as the master disc 8 9 4 Change Bad Master Disc 8 9 5 CD Overburn Enables or disables changing of a master disc during the copy process when an error is detected on the master disc Enables or disables the duplication of overburned CDs 8 9 6 Show HDD Image Allows the image name to be displayed on the LCD screen when Name selecting the HDD as the source drive 8 9 7 Keep Buffer 8 9 8 Boot Password To set enable or disable load source to the buffer Sets password protection for machine boot up 8 9 9 Setup Password 9 HDD Manager Sets password protection for changing setup options The management for various functions of the hard disk drive HDD Note For this function and submenu to be displayed a HDD must be installed in the duplicator 9 1 Select Image Selects an image file as a source to be copied to the discs 9 2 Disc Image Loads an image to the HDD from a master CD or DVD or Blu ray as
9. Image sell Name Capacity and press to confirm gt A or v to select mode and press ENT to confirm Press gt 8 9 7 Keep Buffer You can set Yes to load source disc to buffer in first round of Copy Test Compare or Copy Compare and do it again without the source disc Or set No to keep buffer not be used Note The source will be only temporary saved in buffer there will be nothing left when you exit the task Copy Test Compare and Copy Compare or reboot the system 8 9 8 Boot Password Sets password protection for the duplicator before the boot up process can be started The boot password prevents anyone unauthorized from using the duplicator system gt ess gt A or v to select mode and press ENT ENT to confirm If Disable is selected no password will be set and the display will direct back to the Setup sub menu 14 If Enable is selected a password must be entered using the following guidelines Use A or v to select the character desired Press ENT to go to the next position There are a total of 6 positions for the password To enable the password set all 6 positions For space press without choosing a character to leave the position empty Press ESC to cancel the process The duplicator will ask for password when the unit is restarted 8 9 9 Setup Password Sets password protection for the duplicator before the setup settings can be altered The setup password prevents unauth
10. a b Change the media type Certain types of media may not be compatible with the drives Poor quality media can also cause high failure rate Lower the burn speed and attempt another copy process Lowering the speed increases the stability of the duplication process Check for available firmware updates for the unit A firmware update may resolve any unspecified issues Machine locks up during the copy process a b C Hold down the ESC button to abort the copy process The copy process will cancel and menu goes back to the last function executed If the button cancel does not work power cycle the unit power the unit off leave off for five seconds and power the unit back on Change the master disc A master disc with error s or a poor quality master disc can cause duplication to lock up at particular points during the copy process Button s do not function on the unit a b The duplicator may be busy Buttons pressed while the duplicator is processing will not perform functions unless otherwise specified Possible faulty button Contact your technical support department for further information One of the drives does not open and or LED does not light up a b Check USB and or Firewire port switch and make sure the switch is in the OFF position before machine power is turned on If a disc is stuck inside a drive insert a paper clip or safety pin in the pinhole underneath the drive door and push gen
11. an Image file 9 3 Set Reader Speed Sets the speed of data loading from the master CD or DVD or Blu ray to the HDD 9 4 Show Image Info Displays the image file information such as image order name file size and type of image 9 5 Rename Image Renames the HDD image partition name up to 8 characters 9 6 Delete Image Deletes an image file in HDD Note A file selected as the source file cannot be deleted until a different image is selected See 9 1 5 9 7 HDD Info Displays the information in HDD such as the number of discs stored on the HDD and the amount of space left in the HDD 9 8 Format HDD Formats the HDD erasing ALL data stored on the HDD Functions 1 Copy This command will copy the master disc placed in the designated Source Drive to all target discs in the Writer Drives This process burns all information contained on the master disc to the target discs so the copies are exact duplicates of the master disc To Start the Copy Process 1 Power on the machine if not already on 2 Eject disc tray of the Source Drive and place the master disc in the designated Source Drive usually the top The master disc is the original of which copies are made 3 Eject disc tray s of the Writer Drives and place blank disc s on the tray s Number of drives used depends on number of copies desired It is not necessary to always use all drives 4 Use the scroll buttons to select the command 1 Copy an
12. arious formats SELECT SOURCE Allows the source drive to be changed to any of the available drives in the duplicator including the Hard Disk Drive HDD 7 1 1 Disc Info Displays basic information of the discs inserted such as disc type amount of data on disc for master disc s in MB and media book type For blank media displays the media book type available Space and speed of the media 7 1 2 Drive Info Displays information of all drives in the aman including the Reader HDD if present and Writer drive s 7 1 3 System Info Displays the duplicator information such as the hardware version buffer Es and currently loaded firmware 7 2 ERASE 7 2 ERASEDISC 7 2 1 a Erase ree all rewritable media CD RW DVD RW DVD RW DL BD RW 7 2 2 Full Erase Formats all rewritable media CD RW DVD RW DVD RW DL E RW 7 3 7 3PRESCAN 7 3 1 gg scan e a scan on the master disc before the copy process starts and ensures the master disc can be copied in the duplicator 7 4 TRACK EDIT Allows for the selection of individual track s from different master audio CDs to create custom compilation 7 4 1 Copy Track Allows the selection of individual track s from the master CD and copies the selected track s onto all target discs 7 4 2 Close Disc Closes the target discs when all of the track s are burned on to all target discs Note The copied disc s will NOT play back without this step Do NOT skip this st
13. d press the ENT button The drives will automatically close trays and begin the copy process 5 Once the copy process is completed the disc trays will eject and the display will read Copy Result Pass X Fail Y with X being the number of successful copies and Y being the number of failed copies To reduce copy failure please refer to the troubleshooting section of the manual gt Press to Eee load disc and a gt Analyze master disc gt execute Copy gt gt Finis h gt Rm oso E eject discs 2 Test This command will simulate the copy process and make sure all target discs are usable The test process does NOT burn anything to the blank disc s A built in diagnostic algorithm is used to verify the chance of successful copy for each target disc To start the Test Process 1 Power on the machine if not already on 2 Eject disc tray of the Source Drive and place the master disc in the designated Source Drive usually the top The master disc is the original of which copies are made 3 Eject disc tray s of the Writer Drives and place blank disc s on the tray s Number of drives used depends on number of discs to be tested It is not necessary to always use all drives 4 Use the scroll buttons to select the command 2 Test and press the ENT button The drives will automatically close trays and begin the test process 5 Once the test process is complete the disc trays will eject an
14. d the display will read Test Result Pass X Fail Y with X being the number of discs that passed the test and Y being the number of failed copies Use discs that have passed the test for the actual duplication gt Press to ene load disc and Kee gt Analyze source disc gt execute Test gt Finis P E gt Start simulation KE h anc a ejeci discs 3 Compare This command compares copied disc s to the master disc and ensures that the copies are exact duplicates of the master disc This command is especially useful for DVDs data CDs and video CDs Note The Compare process is a bit by bit comparison between the master disc and the copied discs This operation ensures that all of the copies are completely identical to the Master disc This command is not applicable to audio CDs To start the Compare process please follow the instructions below 1 Power on the machine if not already on 2 Eject disc tray of the Source Drive and place the master disc in the designated Source Drive usually the top The master disc is the original of which copies are made 3 Eject disc tray s of the Writer Drives and place copied disc s to be compared on the tray s gt Finish gt E o ER p eject disc Number of drives used depends on number of copies to be compared It is not necessary to always use all drives 4 Use the scroll buttons to select the command 3 Compare and press the ENT bu
15. e source drive is changed to the HDD gt Press The source disc loaded to gt HDD as image file A001 gt gt Im Note The Source Disc may be placed in the Reader Drive or any of the Writer Drives 9 3 Set Reader Speed Change the read speed load speed for the HDD The speeds for CD are 1 2 4 8 10 12 16 20 24 32 36 40 44 48 52 56 default MAX The speeds for DVD are 1 2 2 4 4 6 8 10 12 16 18 20 default MAX press ENT ENT to confirm gt Ajor v to select DVD Read and press ENT to confirm 9 4 Show Image Info Shows the image number in sequential order the file name of the image stored on the HDD the type of image stored and the amount of data the image contains in MB for DVD Blu ray or time for CD EE gt DVD disc image of 3 875GB as file A001 gt A or v to select CD Read Speed and gt A or y to select mage and press ENT ENT T to display info CD disc image of 65 min 28 sec as file A003 Ce eeccccscccccvrescccsceccceee 9 5 Rename Image Renames the image instead of using default file names A001 A002 etc Up to 8 characters gt Select the image gt Press file to be gt renamed and press gt p D i gt A or vj to 16 select character Press ENT to go to the next position gt Se gt There are 8 characters for each image name No empty space allowed in the image file name Press ESC to cancel the process
16. ep 7 4 3 Disc Info Displays the information regarding the track s on the disc s and how much space is remaining on the target disc s 7 5 EJECT ALL DISC Allows the duplicator to eject disc 7 6 COPY COUNTER Counts the number of successful and failed copies of CD DVD Blu ray made by the duplicator 7 6 1 Show Counter Show the number of successful and failed copies of CD DVD Blu ray 7 6 2 Enable Counter Set Enable or Disable the Copy Counter 7 6 3 Clear Counter To reset the Copy Counter 7 7 Update Bios Allows for update or rollback of the duplicator firmware 8 1 Auto Start Time Sets auto start time from OFF no auto start to 99 sec Allows the duplicator to automatically start one of six following functions once the master disc and desired number of target disc s are inserted and the drive trays are closed Copy Test Copy amp Verify Copy amp Compare Verify and Compare 8 2 Display Mode Sets the amount of information displayed on the LCD during the performance of various functions 8 2 1 Basic Basic Information Displays 8 3 Button Beep ON or OFF Beeping sound 8 4 Eject on Start Eject all trays after the booting sequence complete 8 2 2 Show Timer Enables or disables the copy time to be displayed when the copy process is finished 8 2 3 Show Speed Displays the speed at which discs are read and writing during various processes 8 4 1 Eject All Discs Eject all trays with disc inside 8 4 2 Do Not Eject
17. nside of the drive s of the duplicator 7 1 2 Drive Info Checks the make model firmware and the channel port of the drive s that are connected to the duplicator gt Press A or v to select 7 1 3 System Info Checks the model number buffer memory and firmware version of the duplicator 7 2 Erase Disc 7 2 1 Quick Erase Performs a quick erase of rewritable RW media for next use Note Do NOT perform this function on recordable R media gt Finish Insert re j Eo writable discs and eke pele press ENT gt E Note If the display shows O o blinking Erasing is in progress If the display shows F P blinking DVD RW Disc Formatting is in progress 7 2 2 Full Erase Performs a full erase and format of rewritable RW media for next use Note Do NOT perform this function with recordable R media gt Insert re writable disc gt Finish Full Erase and press ENT and eject discs Note If the display shows O o blinking Erasing is in progress If the display shows F P blinking DVD RW Disc Formatting IS in progress 7 3 Prescan 7 3 1 Prescan Prescans the master disc and verifies the integrity and quality of the master disc a Select Utility and press ENT to enter the sub menu b Select 1 Pre scan and beem 7 4 Track Edit in 7 4 1 Copy Track Allows the selection of individual track s from the master CD and copies the selected track s
18. orized changes to the system gt Press gt A or v to select mode and gt press ENT to confirm If Disable is selected no password will be set and the display will direct back to the Setup sub menu If Enable is selected a password must be entered using the following guidelines Use A or y to select the character desired Press ENT to go to the next position There are a total of 6 positions for the password To enable the password set all 6 positions For space press without choosing a character to leave the position empty Press ESC to cancel the process The duplicator will ask for password when 11 Setup is selected 9 HDD MANAGER This command is for the management of the hard disk drive HDD installed in the duplicator Note This feature is only available on duplicators with a HDD installed If there is no HDD present in the duplicator this feature will NOT show in the menu of commands 9 1 Select Image Allows the selection of the image s present on the HDD The Scroll buttons cycle through the image s on the HDD and the ENT button confirms the selection while the ESC button cancels the selection The image s are listed in order of which they were loaded Be gt A or v to select ress press ENT to confirm 15 9 2 Disc gt Image Transfers the information from the master CD DVD Blu ray to the HDD After the image s transfer is complete the reader drive is ejected and th
19. process gt Press to gt Analyzing load disc gt source disc gt Copy completed Finish and eject and start Compare gt discs 6 Once the compare process is completed the trays will automatically eject discs that have passed the Copy amp Compare process 5 Set Burn Speed This feature allows you to set the burn speed of various types of disc general CDs data and VCDs audio CDs DVDs and dual layer DVDs DVD DL Selectable burn speeds CD 1 2 4 8 10 12 16 20 24 32 36 40 default 44 48 50 52 56 MAX Audio CD 1 2 4 8 10 12 16 20 24 default 32 36 40 44 48 50 52 56 MAX DVD 1 2 2 4 4 6 8 default 12 16 18 20 22 24 MAX DVD DL 1 2 default 2 4 4 6 8 12 16 18 20 22 24 MAX BD 1 2 default 4 6 8 MAX To Set the Burn Speed 1 Power on the machine if not already on 2 Use the Scroll buttons to select 5 Set Burn Speed Press the ENT button 3 The first soeed selection is for general CDs Use the Scroll buttons to select the desired burn speed and press the ENT button 4 The second speed selection is for audio CDs Use the Scroll buttons to select the desired burn speed and press the ENT button 5 The third speed selection is for DVDs Use the Scroll buttons to select the desired burn speed and press the ENT button Note The selection is only available on DVD duplicators 6 The last speed selection is for DVD DL Use the Scroll buttons
20. tly Make sure the power is OFF during this step Then press the EJECT button of the drive a few times to test the disc tray The blank CD or DVD or Blu ray is not recognized in the writer drive s a b Test the blank disc in another writer drive A faulty writer drive will not recognize blank discs Change the blank disc to another disc A defective blank disc will not be recognized by the writer drive Change the brand of media or media type Certain types of media may not be compatible with the drives Poor quality media can also cause high failure rate 18 Interface SATA SATA SATA SATA for Buffer DDR2 64MB Blu Ray Writing Method DAO TAO RAW BD ROM BD R BD RE DVD ROM DVD Video DVD Audio DVD R Disc Format DVD RW DVD R DVD RW Dual Layer DVD R CD ROM CD I Audio Support CD Video CD CD G CD TEXT Bootable CD Mixed mode CD Multi session CD CD Extra Business Card CD 3 Mini CD R Display 2x16 Backlight Monochrome LCD 40 C 104 F 5 C 41 F Cs fes oo eeler wee eae MB OX 8X Copyright 2010 All rights reserved 19
21. to select the desired burn speed and press the ENT button Note The selection is only available on DVD duplicators gt Press ENT amp A or v gt gt Aj or bel and press all ENT to set general data CD burning speed gt A or v and press to set audio CD burning speed gt gt Aj or v and press to gt Finish i and return to set DVD burning speed gt E GA NC det 6 Select Source This command will allow you to change the source drive to any one of the drive s inside the unit including the HDD if installed To change the source drive inside the unit to a different drive 1 Power on the machine if not already on 2 Use the Scroll buttons to select the 6 Select Source Press the ENT button 3 The current Source Drive will be displayed along with the partial model number of the drive and the port number in brackets 4 Use the Scroll buttons to select from other available drives until the port number of the desired drive is displayed Press the ENT button The desired drive will then become the Source Drive saat gt r Em gt EES gt Alor 8 es des Fe gt Press to finish Setting 7 Utility This command contains various tools to check functionality of the drive s information of the components and other system information gt Display current Source Drive setting gt 7 1 Information 7 1 1 Disc Info Checks the capacity and space used on the disc s i
22. tton The drives will automatically close trays and begin the compare process 5 Once the compare process is complete the trays will eject the discs that have passed the compare process 4 Copy amp Compare This command will perform the copy process and immediately follows with a comparison between the master disc and the copied disc s to ensure the copies are exact duplicates of the master disc This command is especially useful for DVDs data CDs and video CDs Note The Compare process is a bit by bit comparison between the master disc and the copied discs This operation ensures that all of the copies are completely identical to the Master disc This command is not applicable to audio CDs To start the Copy amp Compare process 1 Power on the machine if not already on 2 Eject disc tray of the Source Drive and place the master disc in the designated Source Drive usually the top The master disc is the original of which copies are made 3 Eject disc tray s of the Writer Drives and place blank disc s on the tray s Number of drives used depends on number of copies desired It is not necessary to always use all drives 4 Use the scroll buttons to select the 4 Copy amp Compare command and press the ENT button The drives will automatically close trays and begin the copy process 5 Once the copy process is complete the tray s will open briefly and then automatically close again to begin the compare
Download Pdf Manuals
Related Search