Rode NT6 microphone
Contents
1. RODE MICROPHONES NT Instruction Manual www rodemic com C EMC Iw Introduction We at RODE would like to thank you and congratulate you on investing in the RODE NT Compact Condenser Microphone with Detachable Capsule The R DE NT6 is specifically designed for difficult mounting applications Although clearly relevant to instrument miking the NT6 is extremely well suited to any situation where a small and unobtrusive yet powerful microphone system is required The 1 2 externally biased gold sputtered capsule is designed to attach to a custom made multi position swivel mount allowing it to be independently positioned with ease The capsule is connected to the remote pre amplifier body by a custom 3m DO Kevlar fibre reinforced cable The surface mount pre amplifier circuit also incorporates a two position variable PAD with 0 dB and 10 dB attenuation and a two position variable high pass filter that enables you to step from a flat response to 80Hz high pass filter both conveniently located away from the capsule providing additional control without the need to move the capsule once in position The NT6 is intended for film television broadcast live performance theatre surround and environmental recording applications or wherever your imagination takes you Please take the time to visit www rodemic com and register your microphone for a full ten year warranty While there you can2. Filter that enables you to step from a flat response to 80 Hz high pass filter both conveniently located away from the head providing additional control without the need to move the head once in position Use the High Pass Filter when you wish to remove low frequency noise that is not part of your intended sound source Remember however the tonal characteristics will be affected by this so it is important that you listen to the sound with and without the HPF in circuit before deciding if it is appropriate for the source Asmall screwdriver or pen can be used to alter the switch positions as required Storage e After use the NT6 head should be wiped with a dry soft cloth and both head and body placed in the protective case Be sure to place the moisture absorbent crystals supplied at the head of the microphone so as to absorb any moisture present Eventually this pack of crystals will need to be dried This is indicated by the crystals turning pink in colour Theycan easily be re used by placing them in an oven at 100 150 degrees celsius for approximately ten minutes The crystals will operate effectively again once they have turned blue xq Warranty All RODE microphones are warranted for one year from date of purchase You can extend that to a full ten years if you register online at www rodemic com The warranty covers parts and labour that may be required to repair the mi
3. biased condenser Gold sputtered 1 2 capsule Two position PAD OdB and 10dB Two position High Pass Filter flat and 80Hz Convenient two axis swivel mount and 3m Kevlar fibre reinforced cable included e Heavy duty satin nickel plated body Surface mount circuitry Low noise and full frequency response Madein Australia 10 year warranty Accessories f e RM5 stand mount WS5 windshield Swivel mount ZP1 zip pouch Online product registration required Eb Mounting the NT6 e The NT is supplied with a selection of fittings and adaptors designed to ease positioning and mounting The NT head attaches to a 2 axis swivel mount that allows it to independently move and lock in position To further increase the versatility of the NT6 it comes supplied with 2 threaded adaptors a 1 4 to 5 8 and a 1 4 to 3 8 that enable the capsule assembly to be securely attached to a wide variety of mic stands tripods and boompoles e The larger Adaptor is the 1 4 to 5 8 When screwed into the base of the swivel mount it enable the capsule assembly to be attached to a standard 5 8 thread found on microphone stands The smaller 1 4 to 3 8 adaptor when screwed to the base of the swivel mount enables the head assembly to be attached to a standard tripod or boompole Mounting the NT6 With the capsule securely in position you are ready to connect and position th
4. miniature connection cable is Kevlar fibre reinforced and designed to withstand considerable tensile and compressive forces however inside this sheath are three copper wires Always ensure the connectors are correctly aligned groove to key when connecting the miniature connector s and do not use excessive force when inserting and withdrawing Cable runs of no greater than 10 m 30 are recommended to maintain signal integrity Using the NT The NT is a phantom powered microphone To operate correctly it requires a 24V or 48V phantom supply from the mixing console or other source tisrecommended that you use a high quality microphone lead from the preamp body to the recording device or mixing console and keep it as short as practical for your application This will ensure the highest quality sound reproduction Please ensure all cable connections are secure before applying power to the microphone and allow a few moments for the microphone to stabilise after the power is turned on The pre amplifier body incorporates two switches for varying both the low end frequency response HPF and sensitivity PAD Flat YCID 80Hz High Pass Filter Control C ara 0 0 dB O 10 10 dB PAD Control 10 s Using the NT e The PAD settings provide a 10 dB reduction in sensitivity or commonly referred to as attenuation anda two position variable High Pass
5. crophone during the warranty period The warranty excludes defects caused by normal wear and tear modification shipping damage or failure to use the microphone as per the instruction guide If you experience any problem or have any questions regarding your RODE microphone first contact the dealer who sold it to you If the microphone requires a factory authorised service return will be organised by that dealer We have an extensive distributor dealer network but if you have difficulty getting the advice or assistance you require do not hesitate to contact us directly For information and technical support questions please visit www rodemic com support 12
6. e pre amplifier body as required Like the head the pre amplifier is designed to be positioned and or mounted in several ways The NT6 comes complete with an RM5 Stand Mount When connected to a mic stand the RM5 securely holds the pre amplifier in position This allows the head assembly to be directly suspended from or positioned independently to that of the pre amplifier As long as the pre amplifier is suitably protected from the elements it can be positioned as required As with any recording set up it is best to explore the options you have available and use the product within these constraints Connecting the miniature cable With the head and pre amplifier in position and the XLR cable connected to the back of the pre amplifier it is time to connect the mini XLR connectors With the pre amplifier assembly in one hand and the mini XLR in the other align the key on the connector to the groove on the back of the pre amplifier Gently insert the connector ensuring you align the two elements correctly without applying excessive force during insertion e The same method is to be used when attaching the min XLR to the back of the head assembly The miniature connection cable is more than capable of withstanding the rigours of professional use however it is important to understand and where possible consider the following points Connecting the miniature cable The
7. view studio tips and techniques as well as browse the comprehensive range of accessories for RODE microphones 4 is Peter Freedman RODE Microphones Sydney Australia Specifications Acoustic Principle Directional Pattern Frequency Range Output Impedence Sensitivity Equivalent Noise Maximum Output Dynamic Range Maximum SPL Signal Noise Power Requirement Output Connection Net Weight Pressure gradient Cardioid see graph 40Hz 20kHz selectable HPF 80Hz 12dB octave see graph 2000 3 dB re 1 Volt Pascal 16 mV Q 94 dB SPL 2 dB 1kHz 19 dB SPL A weighted per IEC651 6dBu 8 1kHz 1 THD into 1KO load 119 dB per IEC651 IEC268 15 135dB SPL 2 1kHz 1 THD into 1KQ load 145dB with maximum PAD 75 dB SPL A weighted per IEC651 P48 48V P24 24V phantom supply 3 pin XLR balanced output between pin 2 4 pin amp pin 1 ground 386gm Specifications G 91 1 WH oz Dimensions 188 4 mm 7 3 8 b 5 q me l O o 88 5 mm 2 4 8 20 mm 13 16 lt gt 18mm 3 lt 1 4 x 20 tpi be ES i E 3 g E 3 5 8 x 27 tpi 3 8 x 16 tpi Frequency Response dB re 1 V Pa 39 J I I I 1000 10000 20C Frequency 500 Hz mu 1000 Hz uz 4000 Hz ma Features e Externally
Download Pdf Manuals
Related Search