Hikvision Digital Technology DS-2AF5268N-A surveillance camera
Contents
1. HIKVISION Analog Speed Dome User Manual UD 6L0201D1445A01 User Manual of Analog Speed Dome Thank you for purchasing our product If there is any question or request please do not hesitate to contact the dealer This manual is applicable to Analog Speed Domes This manual may contain several technically inaccurate points or printing errors and the content is subject to change without notice The updates will be added into the new version of this manual We will readily improve or update the products or procedures described in the manual DISCLAIMER STATEMENT Underwriters Laboratories Inc UL has not tested the performance or reliability of the security or signaling aspects of this product UL has only tested for fire shock or casualty hazards as outlined in UL s Standard s for Safety UL60950 1 UL Certification does not cover the performance or reliability of the security or signaling aspects of this product UL MAKES NO REPRESENTATIONS WARRANTIES OR CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS PRODUCT 0203001040523 EMO Hikvision User Manual of Analog Speed Dome Regulatory Information FCC Information FCC compliance This equipment has been tested and found to comply with the limits for a digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when th2. ccccccccccccsssssececececeessaececececeesesaeeeeeesceeseseeseseeecessesesaeseesesseeseeaeaeeeesseene 39 3 7 3 Restoring Default Dome Settings cccccccccccecsssessesecececsesesassecececeeseeeeeeseeeceeseseseeseesceseeseeaeseeeeseseseaaeaeeeeseeee 40 3 7 4 Restoring Default Camera Settings recenseren poiana iiare eieaa r E E an r An aE ib i E EE ES NERSE 41 3 7 5 Reb oting the DOME sioe ee had Rak HR A ve RE EROR Ea FERRE EE EA REENEN AT EE a REEERE 41 unnpeee 42 Appendix 1 Lightning amp Surge Protection esesssesessssesesee nennen nnne nennen nth nans a sessi natas asas ess ense tias assess nina 42 Appendix 2 RS485 Bus Connection cccsesssscccceesesesseseeececseseeaesecececeeseaaeseeeceseeseeaeseeececeeseeeeseeececeeseeaeseeeesceeseaaeaeseceeeeees 43 EMO Hikvision User Manual of Analog Speed Dome Appendix 3 24VAC Wire Gauge amp Transmission Distance Appendix 4 Table of Wire Gauge Standards EMO Hikvision User Manual of Analog Speed Dome Chapter 1 Overview 1 1 Description Integrated with the built in pan tilt unit the speed dome features highly sensitive response and reliable performance The speed dome can be adopted in various surveillance fields with its full integral functions and features such as corridor large venue meeting room station community etc 1 2 Functions Note The functions vary accordi
3. User Manual of Analog Speed Dome 3 6 1 Configuring Alarm Input and Linked Actions Purpose This section explains how to configure the speed dome to respond to alarm events with alarm linked actions such as calling presets patrols patterns scanning etc Steps 1 Move the cursor to enter the alarm configuration submenu MAIN MENUS DOME SETTINGS ALARMS ALARM SETTING ALARMS ALARM SETTING ALARM RESUME ALARM NUM 1 ALARM SEQUENCE 5 PRIORITY HIGH ALARMRESTDELAY 5 ALARM ACT NONE ALARM SETTING AUX NONE ALARM INPUT OPEN BACK EXIT BACK EXIT Figure 3 25 Alarm Configuration Menu 2 Choose the alarm number Steps 1 Move the cursor to ALARM NUM and click the IRIS to enter edit mode 2 Click the up and down direction buttons to select the number of the alarm which is to be configured 3 Click IRIS again to confirm and exit edit mode of this column Note You can configure up to 7 alarms 3 Configure the alarm input 5 Steps 1 Move the cursor to ALARM INPUT and click the IRIS to enter edit mode 2 Click the up and down direction buttons to set the input status You can configure it as OPEN Normally open CLOSE Normally closed or OFF disable the alarm input 3 Click IRIS again to confirm Note If you set the status as OPEN alarm will be triggered by high electricity level if you set the status as CLOSE alarm will be triggered by low electricity level if you set the status as OFF
4. Move the cursor to enter the PATTERNS submenu MAIN MENU DOME SETTINGS PATTERNS PATTERNS PATTERN NUM EDIT PATTERN PREVIEW CLEAR PATTERN REMAINING BACK EXIT Figure 3 17 Pattern Configuration Menu 2 Choose the pattern number Steps 1 Move the cursor to PATTERN NUM and click IRIS to enter edit mode 2 Click the up down direction buttons to select the number of the pattern which is to be configured 3 Click IRIS again to confirm the settings Note Up to 4 patterns can be configured 3 Edit the pattern Steps 1 Move the cursor to EDIT PATTERN and click IRIS to enter edit mode REMAIN MEMORY 100 DONE OPEN QUIT CLOSE Figure 3 18 Edit the Pattern 2 Click the PTZ control buttons and direction buttons to operate the speed dome to draw a movement path including pan scan tilt scan zoom in zoom out etc The speed dome can automatically memorize the path you operated as a pattern 3 Click IRIS again to save the pattern and exit edit mode Notes REMAIN MEMORY indicates the remaining memory of the speed dome for configuring the patterns When it reaches 0 no more patterns can be configured You can also see the EMO Hikvision User Manual of Analog Speed Dome remaining memory shown under PATTERNS menu as REMAINING The pan tilt movements and the lens operations cannot be memorized simultaneously 4 Preview the pattern Enter the PREVIEW menu to preview the current pattern 5 Call
5. to enter edit mode 2 Click the up down direction buttons to set the task status to ON 3 Click IRIS again to confirm the settings and exit edit mode of this column Note If the task action and task time have not been configured you cannot set the status as ON 4 Configure the task action Steps 1 Move the cursor to TASK ACTION and click the IRIS to enter edit mode 2 Click the up and down direction buttons to select the task action from preset 1 8 pattern 1 4 patrol 1 8 pan scan tilt scan random scan frame scan panoramic scan day mode night mode patrol d zero calibration and none 3 Click IRIS again to confirm the settings and exit edit mode of this column 5 Set the task time Steps 1 Move the cursor to TASK TIME and click IRIS to enter edit mode 2 Click the left and right direction buttons to position the cursor to WEEK START H M and END H M 3 Click the up and down direction buttons to set the start time and end time to run the time task 4 Click IRIS to confirm the settings and exit Note The weekday can be set to be from Monday to Sunday or Whole Week the H refers to Hour and the M refers to Minute WEEK WHOLE WEEK START H M 00 00 END H M 00 00 DONE OPEN QUIT CLOSE Figure 3 20 Set the Task Time 6 Delete the task Move the cursor to TASK CLEAR click IRIS to delete the time and action of the current task and click IRIS again to confirm the settings and exi
6. 11 59 17 150 45 130 21 6 34 10 55 16 139 42 140 20 6 32 9 51 15 129 39 150 18 5 30 9 47 14 120 36 160 17 5 28 8 44 13 113 34 170 16 4 26 7 42 12 106 32 180 15 4 25 7 39 11 100 30 190 14 4 23 7 37 11 95 28 200 14 4 22 6 35 10 90 27 EMO Hikvision User Manual of Analog Speed Dome Appendix 4 Table of Wire Gauge Standards American Cross sectional Bare Wire British Wire Gauge min Wire Gauge Gauge SWG Ped of Bare AWG Wire mm2 0 750 21 0 4417 0 800 20 21 0 5027 0 900 19 20 0 6362 1 000 18 19 0 7854 1 250 16 18 1 2266 1 500 15 17 1 7663 2 000 12 14 3 1420 2 500 4 9080 3 000 7 0683 EMO Hikvision First Choice for Security Professionals www hikvision com
7. Accessing and Operating the Menu c cccccccccssssssesecececsesssaesecececsesesassesececeeeeaesesececeesesasseseescessesesaeseaecesseseaaes 13 3 2 Configuring System Information ccccccccccccsssssseceeececsesnsaesecececsesesaeeeeececseseeeeseeeesceeseeaeeesececeesesesseseesesesesaeaeeeeess 14 3 2 1 Viewing System InformatiOn ien tios tuo a RR Ee T Ce a a a CR Aa eO ERR ER EYE FANE aE Ri 14 3 2 2 Configuring System Parameters ccccccccccccessessaeeecccecseseeaecesececeesesaeeeeeeececeeseeaeseeeceseesnsaeseeeesceeseeaeaeeeeeeeeees 15 3 3 Configuring Image Parameters ccccccccccecessssssecececeesesesaesecececseaseseeececseseeaeseeececeeseseesesececseeaaesesecseseseeaaeeeeecs 18 3 3 3 Configuring Camera Parameters eser nn enin tne I asa Reni Ra Ye Ra vua EBEN Eia AR o Ya Fas E Cae render eR 18 3 3 4 Configuring Privacy MaSK visissssussessccccacssssesneanccctearssccsnwaanceuvensscacsasaesesnsusiensoasn se subdessiedavensgasndsh RACER YE RSS aE ERAS RATER 22 3 35 Configuring OSD SETTIM S ccc scccadeandcs ceasnceeocsdeucesconvcestcaaddeavecenteasceadeesesnuacededhaudeskaus 24 3 4 Configuring PTZ Control Parameters cccccesssssececececsesssaesecececseeasesecececseseeasseeececeeseaaesesececseseeasseseesceeseeeaeseeess 26 3 4 1 Configuring PTZ Parameters ccisvecsccsscecesssseceassaaverecenecedssvveevcatiasecestaseanladieactessaavdeersdaccvonssensedasiaccesvasvesheadseavwests 26 3 4 2 Conf
8. CLOSE normally closed Note there are 2 auxiliary outputs configurable 3 Move the cursor to DWELL TIME to set the duration of the auxiliary output signal The configurable rage is 0760 seconds 4 Linkthe auxiliary output to the configured alarm Steps 1 Enter MAIN MENUS DOME SETTINGS ALARMS ALARM SETTING and choose the alarm number that you want to link the auxiliary output to 2 Move the cursor to AUX and click IRIS to configure the auxiliary output to the alarm You can choose NONE to disable auxiliary alarm outputs choose 1 to active AUX 1 or choose 2 to active AUX 2 3 7 Others 3 7 1 Setting the Language of the Menu Enter MAIN MENUS LANGUAGE you can set the language of the on screen display menu in Chinese or in English 3 7 2 Configuring Dome Authentication Purpose You can modify the password and enable disable the password protection to prevent unauthorized settings of the speed dome After you set and enable the password you need to input the password every time you call preset 95 to enter the menu Steps 1 Move the cursor to enter the password modification submenu MAIN MENU gt DOME SETTINGS gt PASSWORD gt EDIT PASSWORD EMO Hikvision User Manual of Analog Speed Dome Click IRIS to enter edit mode 3 Click the left right buttons to select the digit of the current password and click up down or FOCUS buttons to set the new value 4 Click the right direction button to move the cursor
9. Camera Settings Enter MAIN MENU gt RESTORE CAMERA Click IRIS to restore the camera settings to the default value or click IRIS to exit Note Camera settings include the image parameters lens settings and display settings 3 7 5 Rebooting the Dome Enter MAIN MENU gt REBOOT DOME and click IRIS to reboot the speed dome remotely EMO Hikvision User Manual of Analog Speed Dome Appendix Appendix 1 Lightning amp Surge Protection This product adopts TVS plate lightning protection technology to avoid damage caused by pulse signal that is below 3000V like instantaneous lighting stroke surging etc According to the actual outdoor situation necessary protection measures must be taken besides ensuring the electrical safety The distance between signal transmission wires and High voltage equipment or high voltage cable is at least 50m Outdoor wiring should better be routed under eaves as much as possible In the open field wiring should be buried underground in sealed steel pipe and the steel pipe should be one point grounding Overhead routing method is forbidden In strong thunderstorm area or high induction voltage areas such as high voltage transformer substation high power lightning protection apparatus and lightning conductor are necessary to be added The design of lightning protection and grounding of the outdoor devices and cables should be considered together with the lightning protection demand of buildings It
10. DVR MAIN MENUS SYS INFO DOME SETTINGS RESTORE DEFAULTS gt RESTORE CAMERA lt RESBOOT DOME gt lt LANGUAGE gt ENGLISH lt SET TITLE gt OFF EXIT Figure 3 2 Main Menu To move the cursor and operate the menu Move the cursor up down On control panel of the live view interface of the DVR click up and down direction buttons or FOCUS and FOCUS buttons to move the cursor in the menu up and down Enter Exit On control panel of the live view interface of the DVR click IRIS to enter a submenu move the cursor to BACK in the menu and click IRIS to return to the previous menu move the cursor to EXIT in the menu and click IRIS to exit the main menu Page up page down There is no RETURN or NEXT menu items for turning page up or down On control panel of the live view interface of the DVR you can click left and right direction buttons to turn page up or down To change the value of a parameter Steps 1 Move the cursor to the target item and click IRIS button You can see the shape of cursor changes Click the up down or left right buttons in the PTZ control panel to choose the value from the selectable value list Press IRIS to confirm the change or click IRIS to cancel and restore the original value You can see the shape of cursor changes again 3 2 Configuring System Information 3 2 1 Viewing System Information Purpose System information menu displays the current system information of the s
11. also must conform to the related national standards and industrial standards The system should be equipotential grounded The grounding equipment must conform to the demands of system anti jamming and electrical safety both and it must not appear short circuit or mixed circuit with the zero conductor of strong grid When the system is grounded alone the resistance should be no more than 4Q The sectional area of the grounding cable should be no less than 25mm2 For grounding instructions please refer to the Installation Manual of Speed Dome video arrester communicate arrester lightning rod porer arrester The speed dome should be in the range of 45 degrees under the lightning rod the resistance of earthing conductor should be smaller than 42 steel jacket Figure A 1 Lightning amp Surge Protection EMO Hikvision User Manual of Analog Speed Dome Appendix 2 RS485 Bus Connection General Property of RS485 Bus According to RS485 industry bus standard RS485 is a half duplex communication bus which has 1200 characteristic impendence the maximum load ability is 32 payloads including controller device and controlled device RS485 Bus Transmission Distance When using 0 56mm 24AWG twisted pair line according to different baudrate the maximum transmission distance theory table is shown as below Table A 1 Max Distance of RS485 Transmission Baudrate Max D
12. it will be triggered when this input channel is shut off Configure the alarm linkage action You can specify the linked action when an alarm occurs On the ALARM ACT submenu you can set the alarm action as preset from 1 to 8 pattern from 1 to 4 patrol from 1 to 8 panning scan tilting scan random scan frame scan panoramic scan day mode night mode or none You can also set the alarm output for the alarm Please refer to Section 3 6 3 Configuring Auxiliary Alarm Output for details Configure alarm priority Enter the PRIORITY menu and set the alarm priority as HIGH MID or LOW EMO Hikvision User Manual of Analog Speed Dome If multiple alarms with different priorities are triggered at the same time the dome only responds to the alarm with the highest priority If multiple alarms with the same priority are triggered at the same time then the dome will respond to each alarm according to the defined alarm sequence 3 6 2 Configuring Alarm Parameters Purpose You can set the alarm related parameters following below instructions including linkage action interval alarm duration and dome activity resumption Steps 1 Enter the alarm parameter configuration menu MAIN MENUS DOME SETTINGS ALARMS ALARM SETTING 2 Configure the interval of the alarm sequence When more than one alarm of the same priority occurs at the same time the speed dome will respond to one alarm first and then respond to the next one after the user de
13. it will switch to ON automatically if you delete the zone the ZONE STATUS will switch to OFF 5 Clear the zone settings Move the cursor to CLEAR ZONE click IRIS to clear all the settings of the current zone and click IRIS again to confirm the settings and exit 3 4 7 Clearing PTZ Control Settings Purpose EMO Hikvision User Manual of Analog Speed Dome You can clear all user defined PTZ control settings including presets patrols patterns zones and time tasks You can also clear privacy masks on this menu Steps 1 Enter the CLEAR SETTINGS menu MAIN MENU DOME SETTINGS CLEAR SETTINGS CLEAR SETTINGS CLEAR ALL PRESETS CLEAR ALL PATROLS CLEAR ALL PATTERNS CLEAR ALL BLANKS CLEAR ALL ZONES CLEAR ALL TIME TASKS DIAGNOSTICS BACK EXIT Figure 3 22 Clear Dome Settings 2 Move the cursor to each item e g CLEAR ALL PATTERNS and click IRIS to enter the corresponding submenu Click IRIS again to confirm the settings and exit On DIAGNOSTICS submenu you can see the self diagnostics information of the speed dome For more details please refer to the table below DIAGNOSTICS DIAGNOSTICS HIGH TEMP PAN LOST HIGHEST TEMP TILT LOST LOW TEMP CAMERA LOST LOWEST TEMP VIDEO LOSS LOW VOLTAGE POWER UP BACK EXIT BACK EXIT Figure 3 23 Self diagnostics Table 3 2 Descriptions of self diagnostics information wem Deedpion S O The lowest temperature o LOWEST TEMP The lowest temperature VIDEO LO
14. proper operating environment While shipping the product should be packed in its original packing Please use the provided glove when open up the product cover Do not touch the product cover with fingers directly because the acidic sweat of the fingers may erode the surface coating of the product cover Please use a soft and dry cloth when clean inside and outside surfaces of the product cover Do not use alkaline detergents Improper use or replacement of the battery may result in hazard of explosion Please use the manufacturer recommended battery type EMO Hikvision User Manual of Analog Speed Dome Table of Contents Chapter 1 aul e 7 1 1 DESCHIPEIOMN BERE REED S e EDDA C M P CA 7 1 2 BUI CELOMS TE RR 7 Chapter 2 Getting Started Pee 10 2 1 Power Up AHORN e M 10 2 2 Basic OperatlOIns c ctt eie iecur edet Ra uto qme ee eux nd eo eee ES ex E ORNA A oie Su Aen RE SERERE SURE de RAS HEU RE EN Yi aS eU eR SERE EXE QUERER A DERE ENTER RN E 11 2 3 Systemedefined PEesSets ide AEEA A T AEE A En RU Ete E Eee RUE E v ove PER AA eR Ue vun AA 11 2 4 On screen Displays oot ette viet ei e eee eren dares ned te dau audere drei gas ede Be E eR d e wea 12 Chapter 3 uINeIICuDIPSMe T 13 3 1
15. the defined pattern You can call the special presets to call the defined pattern E g call preset 41 to call pattern 1 Please refer to Section 2 3 to find the corresponding preset number for each pattern 6 Delete the patterns To Delete a Chosen Pattern Click IRIS to enter EIDT PATTERN and you can see DEL PATH ABOVE Click IRIS to delete the pattern Note If you delete the current pattern the following pattern will also be deleted E g if pattern 2 is deleted pattern 3 and pattern 4 will be deleted as well To Clear All the Patterns Enter CLEAR PATTERN menu and click IRIS to delete all the defined patterns 3 4 5 Configuring Time Tasks Purpose A time task is a preconfigured action that can be performed automatically at a specific date and time Steps 1 Move the cursor to enter the TIME TASK submenu MAIN MENU gt DOME SETTINGS gt TIME TASK TIME TASK TASK NUM TASK STATE TASK ACTION TASK TIME TASK PREVIEW TASK CLEAR BACK EXIT Figure 3 19 Time Task Configuration Menu 2 Choose the task number Steps 1 Move the cursor to TASK NUM and click IRIS to enter edit mode 2 Click the up down direction buttons to select the number of the task which is to be configured 3 Click IRIS again to confirm the settings and exit the edit mode Note Up to 8 time tasks can be configured 3 Set the task status EMO Hikvision User Manual of Analog Speed Dome Steps 1 Move the cursor to TASK STATE and click IRIS
16. the device should be firmly fixed To reduce the risk of fire or electrical shock do not expose the indoor used product to rain or moisture This installation should be made by a qualified service person and should conform to all the local codes Please install blackouts equipment into the power supply circuit for convenient supply interruption If the product does not work properly please contact your dealer or the nearest service center Never attempt to disassemble the product yourself We shall not assume any responsibility for problems caused by unauthorized repair or maintenance EMO Hikvision User Manual of Analog Speed Dome ALL Make sure the power supply voltage is correct before using the product Do not drop the product or subject it to physical shock Do not install the product on vibratory surface or places Do not expose it to high electromagnetic radiating environment Do not aim the lens at the strong light such as sun or incandescent lamp The strong light can cause fatal damage to the product The sensor may be burned out by a laser beam so when any laser equipment is being used make sure that the surface of the sensor not be exposed to the laser beam Do not place the dome in extremely hot cold dusty or damp locations otherwise fire or electrical shock will occur For operating temperature please refer to the specification manual for details To avoid heat accumulation good ventilation is required for a
17. the user definable presets can be programmed to use pan tilt camera settings and other settings When preset is called the dome will automatically move to the defined position User is allowed to add modify delete and call each preset EMO Hikvision User Manual of Analog Speed Dome Label Display The on screen label of the preset title time zoom and other operations can be programmed by menu and displayed on the monitor Auto Flip In manual tracking mode when a target object goes directly beneath the dome the dome will automatically rotate 180 degrees in horizontal direction to maintain continuity of tracking Privacy Mask The privacy mask allows a user to program user defined areas that cannot be viewed by the operator of the dome system A masked area will move with pan and tilt functions and automatically adjust in size as the lens zooms telephoto and wide Proportional Pan Proportional pan automatically reduces or increases the pan and tilt speeds in proportion to the amount of zoom At telephoto zoom settings the pan and tilt speeds will be slower for a given amount of joystick deflection than at wide zoom settings This keeps the image from moving too fast on the monitor when there is a large amount of zoom Auto Focus The auto focus enables the camera to focus automatically to maintain clear video images DAY NIGHT Auto switch The speed dome delivers color images during the day as light diminishes at night it switches
18. 4 Return to home position 94 Remote reboot 35 Patrol 1 95 Access main menu 36 Patrol 2 96 Stop scanning 37 Patrol 3 97 Start random scanning 38 Patrol 4 98 Start frame scanning 39 IR cut filter in 99 Start auto scanning 40 IR cut filter out 100 Start tilt scanning 41 Pattern 1 101 Start panorama scanning 42 Pattern 2 102 Patrol 5 43 Pattern 3 103 Patrol 6 44 Pattern 4 104 Patrol 7 46 Quick Patrol 105 Patrol 8 92 Enable limit stops EMO Hikvision User Manual of Analog Speed Dome Note For Manchester code control protocol the system defined presets with special functions are shown as below Table 1 1 System defined Presets of Manchester Code Control Protocol Set Preset Function Call Preset Function No No 65 Remote reboot 67 Auto flip 66 Access main menu 70 Run Pattern 1 69 Stop recording pattern 71 Run Pattern 2 70 Record Pattern 1 72 Run Pattern 3 71 Record Pattern 2 72 Record Pattern 3 2 4 On screen Displays The speed dome supports following on screen displays Zoom Identifies the amount of magnification The format is ZXXX XXX is the zoom amount Direction Displays panning and tilting direction with the format of NEXXX TXXX The XXX following NE indicates the degrees in north east direction while the XXX following T indicates the degrees in tilt position Time Supports for time display Preset Title Identifies preset being called EMO Hikvision User Manual of An
19. SETTINGS PRIVACYS PRIVACY BLANKS BLANK NUM 1 BLANK STATUS OFF SET BLANK CLEAR BLANK BACK EXIT Figure 3 8 Privacy Mask Configuration Menu 2 Choose the privacy mask number Steps 1 Move the cursor to BLANK NUM and click IRIS to enter the editing mode 2 Click the up and down direction buttons to select a mask number for configuration 3 Click IRIS again to confirm and exit the editing mode Note The configurable privacy mask number varies according to the camera models 3 Configure the position and size of the privacy mask Steps 1 Move the cursor to SET BLANK and click IRIS button to enter the editing mode as shown in the following figure You can see a privacy mask on the live window ADJUST BLANK POS FOCUS SHIFT STATUS SAVE OPEN QUIT CLOSE Figure 3 9 Set the Privacy Mask 2 You can see ADJUST BLANK POS message on the screen Click the direction buttons to adjust the position of the privacy mask to the designed scene 3 Click FOCUS button and you can see ADJUST BLANK SIZE message on the screen Click the up down buttons to increase decrease the height of the mask and click right left buttons to increase decrease the width of the mask Click IRIS button to save the settings and return to the previous menu and you can see the mask turn to gray 4 To modify the configured mask click IRISt button to enter the SET BLANK menu and click IRIS button again to modify Note The tilt range for confi
20. SS The occurrence times of video loss LOW VOLTAGE The occurrence times of low voltage lower than the working voltage EMO Hikvision User Manual of Analog Speed Dome mem O Decnpio POWER UP The occurrence times of abnormal reboot PAN LOST The occurrence times of panning loss TILT LOST The occurrence times of tilting loss CAMERA LOST The occurrence times of communication loss Note The panning loss and tilting loss refer to the failures of panning and tilting movement and are for diagnosing the electric motor of the speed dome 3 5 Configuring the Smart Tracking Purpose When the smart tracking is enabled the detected moving object will be fixed in the center of the image through the panning tilting and zooming operations Steps 1 Enter the SMART SETTINGS menu MAIN MENU gt DOME SETTINGS gt SMART SETTINGS SMART SETTING TRACK ACTIVE ON TRACK ZOOM BACK EXIT Figure 3 24 Smart Settings Move the cursor to TRACK ACTIVE and click FOCUS to change the cursor to hollow Click IRIS to select ON for enabling this function Move the cursor to TRACK ZOOM and click FOCUS to change the cursor to hollow Click the PTZ buttons to get a scene you want The speed dome tracks according to the zoom ratio you set 6 Click IRIS to save the settings wPwn 3 6 Configuring and Handling Alarms Note The alarm related function is supported by the IR speed dome and 5 inch high speed dome EMO Hikvision
21. Task A time task is a preconfigured action that can be performed automatically at a specific date and time The programmable actions include preset 1 8 pattern 1 4 patrol 1 8 pan scan tilt scan EMO Hikvision User Manual of Analog Speed Dome random scan frame scan panorama scan day night mode or none EMO Hikvision User Manual of Analog Speed Dome Chapter 2 Getting Started 2 1 Power up Action After the power is connected the speed dome will perform a series of self test actions It performs lens actions firstly then the panning movement and the tilting movement at last After the power up self test actions the system information will be displayed for 2 minutes on the live view screen as shown below TYPE XX XXXX X SN XXXXXXX ADDRESS 0 COM FORMAT 2400 8 1 PROTOCOL ADAPTIVE VERSION 0 00 BUILD DATE XX XX XX Figure 2 1 System Information Table 2 1 Descriptions of the System Information Description The model of the speed dome The serial No of the speed dome which is unique The default communication address of the speed dome The communication settings of the speed dome including baudrate 2400 by default data bit 8 by default and stop bit 1 by default It is for the communication with other devices The version of the firmware The date when the program of the software is compiled Notes You have to configure the address and the baudrate for
22. alog Speed Dome Chapter 3 Menu Operation The OSD menu tree is shown in the following figure Note The menu varies depending on the model of speed dome MAIN MENUS DOME RESTORE SYS INFO SETTINGS DEFAULTS p EM i SYS INFO RESTORE TYPE TEMPERATURE SETTINGS PRIVACYS CAMERA do CAMERA ADDRESS VERSION ALARMS PARAMETER EINST DOME MOTION COM FORMAT BUILD DATE PARAMETER AUXS CLEAR LANGUAGE PROTOCOL PRESETS SETTINGS PATROLS PASSWORD SET TITLE TIME TASK ZONES SMART PATTERNS SETTINGS Figure 3 1 Main Menu Before you start You can operate the speed dome using the on screen display menu remotely by connecting to a DVR or an Encoder Examples of entering speed dome menu are listed as follows Enter the menu by pressing buttons PTZ gt REC gt 9 gt 5 on the front panel of the DVR Enter the menu by pressing buttons CALL gt 9 gt 5 gt ENTER on the keyboard Enter the menu via the web browser of a DVR or encoder Menu operations via the web browser of a DVR will be taken as an example in this chapter 3 1 Accessing and Operating the Menu To enter the main menu Steps 1 Connect the video and RS 485 cables of speed dome to a DVR 2 Visit the DVR via the web browser 3 Getthe live view of the speed dome EMO Hikvision User Manual of Analog Speed Dome 4 For PELCO P D and other private PTZ protocols call preset 95 from the preset list in the PTZ control panel of the
23. ase the best way is adding a RS485 distributor This product can effectively change the star shape connection to which satisfies the requirement of RS485 industry standard in order to l 32 Controller Device 154 Figure A 4 Star Shape Connection avoid those problems and improve the communication reliability Show as figure 5 RS485 Distributor I 1200 I 1200 I 1200 164 Figure A 5 RS485 Distributor Troubleshooting of RS485 communication Problem Possible Reasons To Solve the Problem 1 Adjust the address and 1 The address or baudrate of the J baudrate of the remote control The speed speed dome does not match with device to match with those of the dome does those of remote control device i speed dome e i 2 The wire RS485 connects to self test 2 Connect the wire RS485 to the the interface RS485 and wire i i action but interface RS485 and wire RS485 RS485 connects to the interface i cannot be to the interface RS485 RS485 controlled 3 The RS485 wire is 3 Reconnect the RS485 wire remotely disconnected tightly 4 RS485 wire is broken 4 Change a RS485 wire Thespeed 1 The connection is loose 1 Reconnect
24. ation The battery is marked with this symbol which may include lettering to indicate cadmium Cd lead Pb or mercury Hg For proper recycling return the battery to your supplier or to a designated collection point For more information see www recyclethis info C This product and if applicable the supplied accessories too are marked with CE EMO Hikvision User Manual of Analog Speed Dome Safety Instruction These instructions are intended to ensure that the user can use the product correctly to avoid danger or property loss The precaution measure is divided into Warnings and Cautions Warnings Serious injury or death may be caused if any of these warnings are neglected Cautions Injury or equipment damage may be caused if any of these cautions are neglected A A Warnings Follow these safeguards to Cautions Follow these precautions to prevent serious injury or death prevent potential injury or material damage Au Please adopt the power adapter which can meet the safety extra low voltage SELV standard And source with the voltage in the specification manual depending on models according to the IEC60950 1 and Limited Power Source standard The power consumption cannot be less than the required value Do not connect several devices to one power adapter as an adapter overload may cause over heating and can be a fire hazard When the product is installed on a wall or ceiling
25. change the value 3 Click the up down direction buttons to increase decrease the value 4 Click IRIS button to confirm and exit Y M D 07 01 18 H M S 15 33 25 DONE OPEN QUIT CLOSE Figure 3 5 Set the System Time Zero angle initial position configuration Purpose You can define the initial position in the panning direction on the ZERO ANGLE submenu Steps 1 Move the cursor to ZERO ANGLE using the direction buttons and click IRIS to enter EMO Hikvision User Manual of Analog Speed Dome 2 Click the left right up down direction buttons to adjust the view angle 3 Click IRIS button to confirm and exit IR LED Parameters IR PARAMETER IR SENSITIVITY LOW N M LED CURRNT 2 FAR LED CURRNT 2 REFERENCE HEIGHT M N A REFERENCE ZOOM N A LED CONTROL AUTO BACK EXIT Figure 3 6 IR Parameter IR Sensitivity When the LED CONTROL mode is AUTO the IR LEDs are turned on or off according to the illumination of the scene The IR SENSITIVITY is higher the IR LEDs are turned on or off easier when the illumination changes The IR SENSITIVITY can be set to LOW MEDIUM or HIGH LED Current Configure the N M LED CURRENT and FAR LED CURRENT to adjust the brightness of NEAR MEDIUM and FAR LEDs The brightness value ranges from 1 to 10 LED Control Configure the LED CONTROL to set the LED control mode The LED control mode can be AUTO FAR far irradiation distance LEDs ON M F medium and far ir
26. different camera models Some models don t support user defined BLC level Task 6 Configuring the iris gain and shutter speed Setthe AE Mode Purpose AE mode defines the priority of iris shutter and gain while the speed dome adjusting the brightness of the live view You can change the mode on AE MODE submenu AUTO Auto iris auto shutter and auto gain The speed dome adjusts the values automatically responding to the lighting conditions It is the default mode IRIS User defined iris value auto shutter and auto gain It is the iris priority mode Please define the iris value according to related content in this section if you choose IRIS mode SHUTTER User defined shutter speed auto iris and auto gain It is the shutter priority mode Please define the shutter speed according to related content in this section if you choose SHUTTER mode MANUAL User defined iris gain and shutter Please define the iris value gain value and shutter speed according to related content in this section if you choose MANUAL mode Setthe lris Value The IRIS value measures the amount of light entering to the lens You can set the iris value from 0 to 17 in response to the changing light conditions Note Iris is fully closed at value 0 and fully open at value 17 EMO Hikvision User Manual of Analog Speed Dome Setthe Gain Gain value The value of gain indicates the amplification degree of the original image signal You can set the value f
27. e equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense FCC Conditions This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation EU Conformity Statement and comply therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2006 95 EC the EMC Directive 2004 108 EC the RoHS Directive 2011 65 EU 2012 19 EU WEEE directive Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union For proper recycling return this product to your local supplier upon the purchase of equivalent new equipment or dispose of it at designated collection points For more information see www recyclethis info 2006 66 EC battery directive This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union See the product documentation for specific battery inform
28. fined interval You can set the on ALARM SEQUENCE submenu from 1 to 200 seconds 3 Configure the alarm rest delay If there s a linkage action has already been triggered by an alarm input the speed dome will only respond to the input from the same channel again after the user defined reset delay time This is the rest time that the speed dome considers an alarm to be active when it s physically cleared You can set the ALARM REST DELAY from 0 to 300 seconds 4 Resume the dome activity You can set ALARM RESUME to ON to enable the speed dome to resume its previous activity after the triggered actions finished Notes f the speed dome is moving when a linkage action is triggered it will stop at the current position and resume from this position after the linkage action finishes The speed dome can be configured to resume the PTZ positions focus and iris value 3 6 3 Configuring Auxiliary Alarm Output Purpose An auxiliary output is a configurable alarm output interface on the speed dome back box which can connect and trigger another alarm device to operate Steps 1 Enter the alarm auxiliary output configuration submenu MAIN MENUS DOME SETTINGS AUXS EMO Hikvision User Manual of Analog Speed Dome AUX AUXI CLOSE DWELL TIME AUX2 DWELL TIMB BACK EXIT Figure 3 26 Configure the AUX Output 2 Click IRIS to edit the status of the auxiliary outputs You can set the alarm output type as OPEN normally open and
29. guring the privacy masks is from 0 to 70 EMO Hikvision User Manual of Analog Speed Dome Enable or disable the privacy mask function Move the cursor to BLANK STATUS Click IRIS button to enter the editing mode and click the up and down direction buttons to set it ON or OFF Note If no privacy mask has been configured you cannot set the status as ON Delete the privacy mask You can enter the CLEAR BLANK menu to delete the current privacy mask 3 3 5 Configuring OSD Settings Purpose You can configure the on screen display of the dome name PTZ control information viewing direction etc Display the dome title Steps 1 Enter the dome title setting menu MAIN MENUS gt SET TITLE 2 Click IRIS to enter the editing mode 3 Click FOCUS to set it to ON 4 Click IRIS again to confirm 5 Exit the MAIN MENUS interface 6 On the live view screen call preset 11 twice within 5 seconds to enter the SET TITLE menu as shown in the following figure Figure 3 10 Set Dome Title 7 Click the left right direction buttons to position the cursor to the characters of the title 8 Get the codes for a specific character and enter each code number by calling the preset number i e calling presets 1 9 to enter number 1 9 respectively and calling preset 10 to enter number 0 Note You can get the codes of a specific character using the software we provided For example if you want to display the word HALL as a part of t
30. he dome name please follow below steps Steps 1 Enter HALL in the Title filed of the software click OK and you ll see the corresponding codes 0227 0220 0231 0231 listed for it EMO Hikvision User Manual of Analog Speed Dome Title al 0221 0220 0231 0231 Figure 3 11 Get the Codes of a Character 2 On the SET TITLE menu call the presets standing for each code in sequence to enter the codes E g call preset 10 to get 0 and call preset 2 to get 2 The corresponding numbers characters and position information will be displayed on the screen when you are calling the presets 3 You can call preset 16 to delete the character at the current position Note You can set up to 15 characters for the dome title 9 Exit the title setting menu and display the dome title You can call preset 12 twice within 5 seconds to exit the title setting menu and display the title in the lower right corner or call preset 13 twice within 5 seconds to exit the title setting menu and display the title in the lower left corner or call preset 14 twice within 5 seconds to exit the title setting menu and display the title in the upper left corner or call preset 15 twice within 5 seconds to exit the title setting menu and display the title in the upper right corner Note After exit the SET TITLE menu you can call preset 12 twice within 5 seconds to delete the defined title and remove it from the screen Display the PTZ movements alarm s
31. he time that the speed dome stays on a certain preset the patrol speed level 1 40 selectable is the scanning speed the speed dome switching between the presets 4 Follow the above steps to define the other presets for the selected patrol You can configure up to 32 presets in sequence for a patrol Press IRIS to save the new settings or press IRIS to cancel and return to the previous menu Preview the patrol Move the cursor to PREVIEW and click IRIS to preview the current patrol You can click IRS again to stop the preview Call the defined patrol You can call the special presets to call the defined patrol E g call preset 35 to call patrol 1 Please refer to Section 2 3 to find the corresponding preset number for each patrol Delete a patrol You can move the cursor to CLEAR PATH and click IRIS to delete the current patrol Configuring the shortcut patrol Calling the system defined preset 46 can enable the shortcut patrol The patrol starts from the number 1 preset to number 32 preset by default You can set the duration time in a preset scene by adjusting PATROL D TIME The value can be 5 10 20 30 and 60s 3 4 4 Configuring Patterns Purpose A pattern is a memorized repeatable series of pan tilt zoom and preset movements that can be recalled by a command or automatically performed by a configured function park time task and power up EMO Hikvision User Manual of Analog Speed Dome Steps 1
32. iguring Presets ce ciere otra mee E A EEEE E E E a E A EEA 28 343 Configuring PAthOlS RTEA E AN TEE EE TEE S RR CHR AN SEEE AEA 29 BAA Configuring Patteriston ieas aei ae enu a eaa e eoa damna eani eae akaa asecestodsanlacecescsawedvenndendvensd 30 3 4 5 Configuring Time Tasks oerte eoa e rnt aane ee ea aee ena Ta Eee Y ken V EET Y nan aeu Exe Curae EY REN ad 32 3 4 6 Configuring ZORG rct reete eee a RR Ea CERTA ERE AR URRV KA KER RR VE RRENRERK REO Ya CERES ERR TORRE TR NE NEAEN RA REN RAS CERR RR ERE muc 33 3 4 7 Clearing PTZ Control Settings sireenin enei E a aE Ea e e E a a E E 34 3 5 Configuring the Smart Tracking cccccccccccccsssssssesececseseseseesececeeseeeaesesececseeaesseeececeeseseesesececeeeaesaesececeeseesaeseeess 36 3 6 Configuring and Handling Alarms c ccccccccccsssssececececsessseesecececseseeaeseeeeeceesneaeseeeesceeseeaeeesececsesaeseseeseeeseaeaeeeeess 36 3 6 1 Configuring Alarm Input and Linked Actions eese eene nnne eene rn nnns sisse nete anna sse 37 3 6 2 Configuring Alarm Parameters ceceni seerne rii irkaii iae aeae ir ne aai iaeaea in nekai RE atki 38 3 6 3 Configuring Auxiliary Alarm Output u u sssssssssssseesersssnse sneen sense nn terna nns essent rasan asses essensen essens 38 3 7 al tM EEG 39 3 7 1 Setting the Language of the Men s sorena aiin aka aE a Ea a E EAEE a a REEE EER 39 3 7 2 Configuring Dome Authentication
33. imit the minimum zoom of the lens Note The wide limit function is supported by certain camera model series Chroma Suppress This function suppresses the color noise so as to get the clear and high quality image in the low luminance environment The value ranges from 0 to 3 Note The Chroma Suppress function is supported by certain camera model series Saturation Saturation indicates the brightness of the color The higher the saturation the brighter the color is Note The saturation function is supported by certain camera model series Contrast Contrast is the degree of difference between the darker and lighter parts of the image Note The contrast function is supported by certain camera model series HLC This function can brighten the darker area and weaken the highlight area of the image Note The HLC function is supported by certain camera model series HR Mode Set the HR MODE as ON to adjust the resolution higher Switch it OFF to disable the function which can avoid cross color of the image 3 3 4 Configuring Privacy Mask Purpose Privacy mask enables you to cover certain areas on the live video from being live viewed and recorded The masked areas can move with the panning tilting movements and automatically adjust the size as the lens zooming in out Steps EMO Hikvision User Manual of Analog Speed Dome 1 Move the cursor to enter the privacy mask configuration submenu MAIN MENUS DOME
34. istance 2400BPS 1800m 4800BPS 1200m 9600BPS 800m The transmission distance will be decreased if we use the thinner cable or use this product under the strong electromagnetic interference situation or there are lots of devices are added to the bus on the contrary the transmission distance will be increased Connection Methods RS485 industry bus standard require daisy chain connection method between any devices both sides have to connect a 1200 terminal resistance show as Diagram 1 the simplified connection method is shown as diagram 2 but the distance of D should not be too long 120 1200 1 2 3 4 32 Figure A 2 RS485 Connection 1 xL TT Li M i 3 314 Figure A 3 RS485 Connection 2 Problems in the Practical Application Normally users adopt star shape connection method in construction under this situation the terminal resistors must be connected between two farthest devices as Figure 4 1 and 158 but this connection method is not satisfy the requirement of the RS485 industry standard so that it will lead to some problems such as signal reflection anti jamming ability decline when the devices are EMO Hikvision User Manual of Analog Speed Dome faraway At this time the dome will be uncontrollable or self running etc For such c
35. ke sure that the speed dome focuses on the target Note The focus limit value varies according to the models of speed dome Task 2 Configure the zoom settings Setting the zoom limit Purpose Zoom limit is a user defined limitation of the zoom amount Zoom amount optical zoomx digital zoom If you set the zoom limit to the minimum value the digital zoom will be invalid and the optical zoom will reach the maximum value if you set the zoom limit smaller the digital zoom will be enabled Steps 1 Move the cursor to ZOOM LIMIT using the direction buttons and click IRIS to enter 2 Click up down direction buttons to choose the limit from 23 46 92 184 and 368 3 Click IRIS button to confirm Note If you set the ZOOM LIMIT as the minimum value 23 the digital zoom function will be disabled and the optical zoom function is at its maximum value Configure the zoom speed Purpose You can define the speed at which the lens changes from full wide zoom to the optical zoom Steps 1 Move the cursor to ZOOM SPEED using the direction buttons and click IRIS to enter 2 Click up down direction buttons to choose the speed from HIGH default MEDUIM and LOW 3 Click IRIS button to confirm Task 3 Configure the Day Night mode There are two parameters available for day night mode configuration EMO Hikvision User Manual of Analog Speed Dome 1 IR cut filter It can be set as AUTO DAY or NIGHT AUTO The
36. l corresponds to the faster speed to call a preset e Limit stops Purpose The limit stops are user configurable stops which limit the panning and tilting area of the speed dome There are left right up and down limit stops to define an area Steps 1 Move the cursor to LIMIT STOPS and click FOCUS to set it ON to enable this feature Click IRIS to confirm the new settings 2 Move the cursor to SETTING STOPS and click IRIS You will see the message SET LEFT LIMIT on the screen 3 Click the direction buttons in the PTZ panel to configure the left limit stop Click IRIS to confirm EMO Hikvision User Manual of Analog Speed Dome the new settings 4 Follow the prompts to configure the right up and down limit stops on the menu Note The new limit stops will overwrite the existed ones by default 5 You can clear the defined limit stops Click IRIS to enter CLEAR STOPS and click IRIS again to clear the stops Elevation set You can set ELEVATION SET as ON to increase the elevation angle range of the speed dome or set it as OFF to disable the function Note The range of the elevation angle is 5 90 by default and it changes to 2 90 when the ELEVATION SET is set as ON 3 4 2 Configuring Presets Purpose A preset is a user defined monitoring position point You can simply call the preset number to change the monitor scene to the defined position Steps 1 Move the cursor to enter preset configuration submen
37. n scan preset pattern etc automatically after a period of inactivity park time You can set PARK TIME from 5 to 720 seconds and set the park action PARK ACT as preset 1 8 pattern 1 4 patrol 1 8 pan scan tilt scan random scan frame scan panoramic scan day mode night mode patrol d or none Note If no control signal is received after the park time under the following circumstances no park actions will be performed in the process of performing dome actions by calling special presets Image freeze This feature enables the live view to switch directly from the current scene to another scene that is defined by a preset without showing the middle areas between these two scenes It reduces the use of bandwidth in a digital network system and it also provides privacy protection for the middle areas You can set IMAGE FREEZE as ON or OFF to enable or disable this function Note The function varies according to the different camera models PTZspeed Purpose You can define the speed of the dome movements 1 DOME SPEED The manual movement speed of the dome can be set from level 1 to 5 2 SCAN SPEED The scan speed defines the scan degree per second of pan scan tilt scan frame scan random scan and panoramic scan The scan speed is adjustable from level 1 to level 40 and the higher the level is the faster the scan speed is 3 PRESET SPEED The speed of calling a preset can be set from level 1 to 8 The higher leve
38. nd zooming movements and configure PTZ control functions including presets patrols patterns etc for the speed dome 3 4 1 Configuring PTZ Parameters Enter PTZ configuration menu MAIN MENU gt DOME SETTINGS gt MOTION PARAMETER MOTION PRESET SPEED LIMIT STOP lt SETTING STOPS gt CLEAR STOPS ELEVATION SET MOTION AUTO FLIP ON PROPORTIONAL PAN ON PARK TIME 2 PARK ACT NONE SCAN SPEED 28 IMAGE FREEZE OFF DOME SPEED 6 BACK EXIT BACK EXIT Figure 3 13 PTZ Configuration Auto flip In manual tracking mode when a target object goes directly beneath the speed dome the speed dome automatically rotates 180 degrees horizontally for tracking Note AUTO FLIP is set as ON for this speed dome by default and it s not user definable Proportional Panning When the speed dome is zooming in out you can enable the proportional panning function to EMO Hikvision User Manual of Analog Speed Dome automatically reduce or increase the panning and tilting speed according to the zooming amount This function enables the speed dome to trace the object at a proper speed when the speed dome is zooming and the monitored scene is narrowed zoom in or enlarged zoom out You can set PROPORTIONAL PAN as ON or OFF to enable disable the function Note This function is enabled automatically while setting the patterns Parktime and actions Purpose This feature allows the speed dome to start a predefined action park actio
39. ng to the different models of the speed dome Coaxial Control The speed dome with a specified DVR or controller can be sent the control signals via coaxial cable BNC cable OSD On Screen Display The on screen display is an image superimposed on a screen picture used for displaying information and menu Self adaptive Protocol While using RS485 control the speed dome is compatible with PELCO D PELCO P and PRIVATE Code etc and is capable of being self adaptive to these protocols without selecting protocol by DIP switch settings While using coaxial control the speed dome is self adaptive to PELCO D and PRIVATE Code protocols Keyboard Control The pan tilt movement and zoom actions of dome can be controlled by the control keyboard DVR matrix etc Limit Stops The dome can be programmed to move within the limit stops left right up down which are configurable by the control keyboard DVR or client application software Scan Mode The dome provides 5 scanning modes pan scanning tilt scanning frame scanning random scanning and panorama scanning The scanning speed can be set by OSD menu from level 1 to 40 with the corresponding speed ranging from 17 second to 40 second Preset Freeze Frame This feature freezes the scene on the monitor when going to a preset This allows for smooth transition from one preset scene to another and also guarantees that masked area will not be revealed when going to a preset Presets Each of
40. o 14 The default value is 7 You can adjust this value to increase the brightness of the image Task 8 Configure white balance You can set WHITE BALANCE mode as AUTO INDOOR OUTDOOR SELFDEF self defined ATW auto tracking and HAUTO half auto AUTO In Auto mode the dome retains color balance automatically according to the current color temperature INDOOR OUTDOOR These two modes are for indoor use and outdoor use respectively SELFDEF In this mode you can adjust the color temperature manually to meet your own demand Note In SELFDEF mode you need to adjust the RED and BLUE values manually ATW In auto tracking mode white balance is continuously being adjusted in real time according to the color temperature of the scene illumination EMO Hikvision User Manual of Analog Speed Dome HAUTO Selecting this mode the viewed image retains color balance automatically according to the current color temperature Task 9 Configure the image flip If you turn the IMAGE FLIP function on the image will be flipped 180 degree along its central axis like the mirror reflection of the image Task 10 Configure the INIT LENS You can turn INIT LENS on to trigger a spontaneous lens initiation to ensure the normal operation Task 11 Configure the noise reduction To reduce the image noise you can set the NOISE REDUCE to LOW HIGH MIDDLE and OFF Task 12 Configure the image quality Wide Limit Set the wide limit ON can l
41. peed dome If the SOFT ADDR is set to ON the soft address is the valid address for connecting the speed dome The SOFT ADDRESS NUM ranges from 1 to 255 EMO Hikvision User Manual of Analog Speed Dome If the SOFT ADDR is set to OFF the hard address set by the DIP switch is the valid address of the speed dome Task 2 Set the broadcast address of the speed dome When the BROADCAST ADDRESS is set to ON the control devices with address 0 can control the speed dome remotely regardless of the address of the speed dome With this function on the control device with address O is capable of controlling all domes connected to it This function is usually for debugging Soft baudrate settings If the SOFT BAUD ACTIVE is set as ON the soft baudrate is the valid baudrate for the speed dome with 2400 4800 9600 and 19200 selectable If the SOFT BAUD ACTIVE is set as OFF the baudrate should be set by the DIP switch Note After you enable disable the soft baudrate the speed dome will reboot automatically to activate the settings PELCO checksum If the speed dome uses PELCO P or PELCO D protocol you can set the PELCO CHECKSUM as ON for improving the controlling effect System time configuration Steps 1 Move the cursor to SYS TIME using the direction buttons and click IRIS to enter 2 Click the left right direction buttons to position the cursor on the specific item year month day or hour minute second of which you want to
42. peed dome as shown in Figure 3 3 including model address protocol etc The information shown on this submenu is EMO Hikvision User Manual of Analog Speed Dome similar to the system information shown after the power up action Please refer to Section 2 1 for more details Enter the system information display menu MAIN MENUS SYS INFO SYS INFO TYPE XX XXXXX X ADDRESS 0 COM FORMAT 0000 0 0 PROTOCOL XXXXX VERSION 0 00 HARDVERSION 0 00 BUILD DATE 13 08 05 BACK EXIT Figure 3 3 System Information Notes Information on this menu cannot be edited The temperature refers to the internal temperature of the speed dome 3 2 2 Configuring System Parameters Purpose You can check and also edit the system information of software address baud rate system time etc on the system information settings menu Enter the system information settings menu MAIN MENUS DOME SETTINGS SYS INFO SETTINGS SYS INFO SETTINGS PROTOCOL STATUS SET OFF PROTOCOL SET AUTO MATCH 485CHECK SET AUTO COAXITRON ACTIVE ON POWER MEMORY 180S SYS INFO SETTINGS SYS INFO SETTINGS SOFT ADDRESS 1 ZERO ANGLE SOFT ADDR ACTIVE OFF DISPLAY SETTINGS SOFT BAUD 2400 IR PARAMETER SOFT BAUD ACTIVE OFF FAN CONTROL BROADCAST ADDRESS ON EIS FUNCTION PELCO CHECKSUM ON EIS LEVEL SYS TIME PRESET DFOCUS BACK EXIT BACK EXIT BACK EXIT Figure 3 4 System Information Settings Dome address settings Task 1 Set the soft address of the s
43. pose A patrol is a scanning track specified by a group of user defined presets You can call a patrol to scan the scenes automatically among the user defined presets in sequence Steps Move the cursor to enter patrol configuration submenu MAIN MENU gt DOME SETTINGS gt PATROLS PATROLS PATROL NUM EDIT PATROL PREVIEW CLEAR PATH PATROL_D TIME BACK EXIT Figure 3 15 Patrol Configuration Menu Choose the patrol number Steps 1 Move the cursor to PATROLS NUM and click IRIS to enter edit mode 2 Click the up and down direction buttons to select the number of the patrol which is to be configured 3 Click IRIS again to confirm the settings and exit edit mode of this column Note Up to 8 patrols can be configured Edit the patrol Steps 1 Move the cursor to EDIT PATROL and click IRIS to enter edit mode EMO Hikvision User Manual of Analog Speed Dome NUM PRESET DWELL SPEED 6 30 30 30 30 30 30 0 30 DONE OPEN QUIT CLOSE Figure 3 16 Edit the Patrol 2 Click up down direction buttons to choose the number and locate the preset to be edited 3 Click left right direction buttons to position the cursor to the column of PRESET DWELL and SPEED You can click the up down direction buttons to set the value of preset number dwell time and patrol speed Note The presets you set for a patrol should be the ones that have been pre defined by users The dwell time 5 800 seconds selectable is t
44. radiation distance LEDs ON MiD medium irradiation distance LEDs ON M N medium and near irradiation distance LEDs ON and OFF Note The IR function is supported by IR speed dome only Fan parameter configuration You can set the FAN CONTROL as ON or OFF EIS Electronic Image Stabilization configuration You can set the EIS FUNCTION as ON or OFF and set the EIS LEVEL as 0 3 Note The selectable EIS levels vary depending on the camera models Preset direct focus You can set the preset direct focus function ON OF on PRESET DFOCUS submenu Protocol settings You can set the PROTOCOL STATUS SET as ON or OFF and set the PROTOCOL SET as AUTO MATCH PELCP P PELCO D Private code etc EMO Hikvision User Manual of Analog Speed Dome RS 485 checksum setting You can set the 485CHECK SET as ON or AUTO for improving the controlling effect Coaxitron Settings The Coaxitron transmission function can be enabled to transmit the RS485 signal along with the video signal via the BNC cable If the connected encoding device supports the Coaxitron transmission as well the RS485 cable will not be necessary Power Off Memory You can set the duration of Power Memory as 10s 30s 60s 180s or 300s for power off memory 3 3 Configuring Image Parameters 3 3 3 Configuring Camera Parameters Purpose You can set the camera parameters including focus shutter speed iris etc Enter the camera parameters settings men
45. rom 0 to 15 Gain limit The higher gain value you set the more noises will appear in the image You can set the maximum user configurable gain value from 0 to 15 to limit the gain range and control the noises in the image Gain limit function varies according to the different camera models Note You need to change the IRCUT FILTER as DAY or NIGHT mode and set the AE MODE as MANUAL before you adjust the gain value Setthe Shutter Purpose The speed of the electronic shutter controls the amount of light entering to the lens in a unit of time a second You can manually configure the shutter speed for the speed dome and you can also enable the slow shutter function for low lighting circumstances 1 Shutter speed The larger you set the SHUTTER value the faster the shutter speed is the fewer the amount of entering light per second is and the darker the image is You can set the value as 1 2 4 8 15 30 50 125 180 250 500 1000 2000 4000 or 10000 Note The value of X indicates that the shutter speed is 1 X second If you set the SHUTTER value bigger shutter speed is faster the amount of entering light per second is fewer and the image is darker 2 Slow shutter Set SLOW SHUTTER as O 1 2 3 4 or 5 The shutter speed can automatically slow down to extend exposure time under low lighting circumstances to obtain clearer image Task 7 Configure exposure compensation You can set the EXPOSURE COMP value from 0 t
46. speed dome is capable of automatically switching from Black and White mode NIGHT and Color mode DAY regarding to the lightening conditions It is the default mode NIGHT B W You can switch the IR cut filter into Black and White mode to increase then lens sensitivity in low light conditions DAY Color You can switch it to DAY mode in normal lighting conditions Note You can set the IRCUT FILTER value on this menu and you can call preset 39 to set the IR cut filter mode to DAY mode and call preset 40 to set it as NIGHT mode D N level The D N level is the light level for auto D N mode switch As a dividing line IR cut filter switches between DAY and NIGHT when the light condition reaches the user defined D N level Three levels are selectable HIGH MID default and LOW Note D N level configuration varies according to the different camera models Some models don t support user defined D N level 2 Task 4 Configure the sharpness level The sharpness function can increase the gain of the image and sharpen the edges in the picture to enhance the picture details You can set the SHARPNESS level from 0 to 15 Task 5 Configure the BLC and WDR There are two parameters available for BLC and WDR configuration on this menu 1 BLC WDR You can set the value as ON or OFF to enable or disable the functions 2 BLC LEVEL You can manually adjust the backlight compensation level Note BLC level configuration varies according to the
47. t 3 4 6 Configuring Zone Purpose EMO Hikvision User Manual of Analog Speed Dome A zone is a panning and tilting area defined by the left right and up down limit stops You can configure the zones on ZONES submenu You can define a zone when the targeted surveillance scene is limited Steps 1 Move the cursor to enter the zone configuration submenu MAIN MENU gt DOME SETTINGS gt ZONES ZONES ZONE NUM UNDEFINED EDIT ZONE ZONE STATUS SCAN STATUS CLEAR ZONE BACK Figure 3 21 Zone Configuration 2 Choose the zone number 1 Move the cursor to ZONE NUM and click IRIS button to enter the edit mode 2 Click the up and down buttons to select the zone number to be configured 3 Click IRIS again to confirm the settings and exit edit mode of this column Note Up to 8 zones can be configured 3 Configure the zone area Steps 1 Move the cursor to EDIT ZONE and click IRIS button to enter the edit mode 2 You can see SET LEFT LIMIT on the screen Click the direction buttons to set the left limit stop 3 Follow the prompts on the screen to set the right limit up limit and down limit 4 Click IRIS button to save the settings and exit 4 Set the zone status and scan status ZONE STATUS The zone status just indicates the current status of the zone SCAN STATUS You can set the scan status to ON OFF to enable disable the scanning in the zone Note ZONE STATUS is not editable After you edited the zone
48. the RS485 wire EMO Hikvision User Manual of Analog Speed Dome Problem Possible Reasons To Solve the Problem dome can tightly be 2 RS485 or RS485 wire is 2 Change a RS485 wire controlled broken but not 3 Th d d is too f i sada be ca oak da ME 3 Add a terminal resistor smoothly from the remote control device 4 Ti d d Pee ese 4 Add a RS485 distributor connected EMO Hikvision User Manual of Analog Speed Dome Appendix 3 24VAC Wire Gauge amp Transmission Distance The following table describes the recommended max distance adopted for the certain wire gauge when the loss rate of 24VAC voltage is less than 1096 For the AC driven device the maximum voltage loss rate is 1096 allowable For example for a device with the rating power of 80VA which is installed at a distance of 35 feet 10m away from the transformer then 0 8000mm is required as the minimum wire gauge 0 8000 1 000 1 250 2 000 10 283 86 451 137 716 218 1811 551 20 141 42 225 68 358 109 905 275 30 94 28 150 45 238 72 603 183 40 70 21 112 34 179 54 452 137 50 56 17 90 27 143 43 362 110 60 47 14 75 22 119 36 301 91 70 40 12 64 19 102 31 258 78 80 35 10 56 17 89 27 226 68 90 31 9 50 15 79 24 201 61 100 28 8 45 13 71 21 181 55 110 25 7 41 12 65 19 164 49 120 23 7 37
49. the speed dome the same as those in the control devices The speed dome is self adaptive to the PELCO D PELCO P PRIVATE Code VICON and KALATEL 312 protocols EMO Hikvision User Manual of Analog Speed Dome 2 2 Basic Operations You can operate the speed dome using a control device The control devices include the control keyboards DVRs DVSs etc In this and the following chapters operation of the speed dome by the IE browser of a DVR will be taken as an example Panning and tilting Click the direction buttons to control the pan and tilt movement of the speed dome Zooming Click the ZOOM and ZOOM buttons to control the zooming Focusing Click the FOCUS and FOCUS buttons to adjust the focus Iris Click the IRIS and IRIS buttons to adjust the iris 2 3 System defined Presets Purpose The section lists the system defined presets with special functions These presets cannot be edited but can be only called through a control device e g a DVS or web browser To call the system defined presets remotely you can choose the preset number from the list in the PTZ control panel Please refer to table below for details For instance preset 99 is the Start auto scan If you call the preset 99 the speed dome starts auto scan function Table 2 2 System defined Presets Preset No Function Preset No Function 33 Auto flip 93 Set manual limit stops 3
50. to night mode and delivers black and white images with high quality You can also switch it to NIGHT mode manually to increase the sensitivity in low light conditions Wide Dynamic Range WDR The wide dynamic range function helps the speed dome provide clear images even under back light circumstances When there are both very bright and very dark areas simultaneously in the field of view WDR balances the brightness level of the whole image and provide clear images with details White Balance White balance is the white rendition function of the speed dome to adjust the color temperature according to the environment automatically It can remove the unrealistic color casts in the image Patrol The high speed dome support patrols In each patrol user is allowed to specify the scanning track by a group of user defined presets with the scanning speed between two presets and the dwell time at the preset separately programmable Pattern A pattern is a memorized repeating series of pan tilt zoom and preset functions that can be recalled with a command from a controller or automatically by a configured function park time task or power up By default the focus and iris are in auto status during the preset is being memorized Power off Memory This feature allows the dome to resume its previous position or status after power is restored By default setting the dome supports the power off memory capability with the dwell time of 3 minutes Time
51. to INPUT PW AGAIN and input the password again 5 Click IRIS to save the new settings and exit 6 Enter the START USING submenu and switch the status to ON and click IRIS to save PASSWORD START USING INPUT PW 123456 EDIT PASSWORD INPUTPWAG 123456 DONE OPEN BACK EXIT QUIT CLOSE Figure 3 27 Set the Password 3 7 3 Restoring Default Dome Settings Purpose You can reset all dome settings to factory default parameters as shown in the table below Note Dome settings are mainly of PTZ parameters and some system settings e g dome address Enter default dome settings menu MAIN MENU gt RESTORE DEFAUTLS Click IRIS to restore the dome settings to the default value shown as the following table or click IRIS to exit EMO Hikvision Table 3 3 Default Dome Settings Parameters Default Value Dome address 0 Baud rate 2400bps 1200 DIS enti Off resistance Soft address Off Focus HAF Zoom limit Max Optical Zoom Zoom speed High Slow shutter Off IR cut filter Day D N level Mid BLC Off User Manual of Analog Speed Dome AE mode Auto Exposure 7 compensation White balance Auto Auto flip On Proportional pan On Park time 5 seconds Park act None Scan speed 28 Image freeze Off Limit stops Off Time show Off Zone show On Address show Off Error rate show Off Zoom PT Preset show Off 3 7 4 Restoring Default
52. u MAIN MENU DOME SETTINGS PRESETS PRESETS PRESET NUM UNDEFINED PRESET PTZ CLEAR PRESET BACK EXIT Figure 3 14 Preset Configuration Menu 2 Choose the preset number Move the cursor to PRESET NUM and click IRIS to enter Click the up and down buttons to choose the preset number which needs to be edited If the preset has been defined the preset label will be listed under the number if it has not been defined you will see the information UNDEFINED under the number Notes There are up to 255 presets can be set for the speed dome The system defined presets will be displayed on this submenu and they are not editable 3 Set the preset position Move the cursor to PRESET PTZ and click IRIS to edit the preset position Use the direction buttons to move the speed dome to find the desired scene position and then press IRIS to confirm the settings and return to the previous menu or press IRIS to cancel EMO Hikvision User Manual of Analog Speed Dome Note The preset position settings will be restricted by the limit stops if they are defined 4 Call the presets You can select the preset number from the drop down preset list in the control panel of the encoder through a web browser and click the arrow to call a user defined or system defined preset 5 Clear the preset settings Move the cursor to CLEAR PRESET and click IRIS to clear the settings of the current preset 3 4 3 Configuring Patrols Pur
53. u MAIN MENUS DOME SETTINGS CAMERA SETUP CAMERA FOCUS ZOOM LIMIT ZOOM SPEED SLOW SHUTTER IRCUT FILTER D N LEVEL SHARPNESS BACK EXIT CAMERA WHITE BALANCE RED BLUE IMAGE FLIP FOCUS LIMIT INIT LENS NOISE REDUCE BACK EXIT CAMERA BLC WDR BLC LEVEL AE MODB IRIS SHUTTER GAIN EXPOSURE COMP BACK EXIT CAMERA WIDE LIMIT CHROMA SUPPRESS SATURATION CONTRAST HLC HR MODE GAIN LIMIT BACK EXIT Figure 3 7 Camera Settings EMO Hikvision User Manual of Analog Speed Dome Task 1 Configure the focus settings Setting the focus mode Steps 1 Move the cursor to FOCUS using the direction buttons and click IRIS to enter 2 Click up down direction buttons to set the focus mode to AF MF or HAF AF Auto focus The lens remains in focus during PTZ movements MF Manual Focus You need to adjust the focus with Focus and Focus buttons manually HAF Half auto Focus The speed dome focuses automatically only once after panning tilting and zooming 3 Click IRIS button to save the settings Setting the focus limit Purpose This function is used to limit the minimum focus distance You can configure the focus limit longer when the target is at a distance to avoid the speed dome focusing on the objects close to it or configure the focus limit shorter when the target is near the speed dome and avoid it focuses on the objects father You can set FOCUS LIMT to 1CM 1M 5M 20M and AUTO to ma
54. ystem time etc Purpose You can enable or disable the on screen display of PTZ movements presets etc and configure the display time Steps 1 Enter the display settings menu MAIN MENUS DOME SETTINGS SYS INFO SETTINGS DISPLAY SETTINGS DISPLAY SETTINGS DISPLAY SETTINGS ZOOM SHOW 2 ADDRESS SHOW OFF EF SHOW 2 ERROR RATE SHOW OFF ALARM SHOW ON FAN AND HEAT SHOW OFF TIME SHOW ON PRESET SHOW ON ZONE SHOW ON BACK BACK EXIT Figure 3 12 Display Settings 2 Move the cursor to DISPLAY SETTINGS using the direction buttons and click IRIS to enter 3 Move the cursor to the target item and click IRIS and click up down direction buttons to EMO Hikvision User Manual of Analog Speed Dome choose each display mode as ON or OFF and define each display time as 2 seconds 5 seconds or 10 seconds 4 Click IRIS button to confirm Note If you enable the ZOOM and PT OSD both while calling a preset the preset label will be displayed on the screen until the preset finishes The speed dome shows the viewing direction when you manually control it to rotate Table 3 1 Viewing Direction Display Display N NE E SE S SW W NW Indication North Northeast East Southeast South Southwest West Northwest Note The due north direction is 02 It is also the factory default initial position 3 4 Configuring PTZ Control Parameters Purpose You can configure panning tilting a
Download Pdf Manuals
Related Search