KT&C KPC-LP751NU surveillance camera
Contents
1. Video In Monitor ES 0000 When you install the camera please glue the end of cable to keep it stable in order to protect the camera from humidity problems e Service Video Connector Handheld Monitor 10 7 Functions OSD Menu Structure e MODE INSTALLATION SETUP Installation Mode provides a bright video screen for adjusting the angle and focus gt MODE LICENSE PLATE SHUTTER 1 9000 LICENSE PLATE boris License plate Mode provides high contrast and clear license plate images for license plate capture e SHUTTER 1 250 1 500 1 10000 adjusted to 1 500sec measure SETUP 1 30K 1 50K 1 70K 1 90K T 00K MODE LICENSE PLATE Adjusted when LICENSE PLATE MODE is gt SHUTTER 1 9000 performed Initial value 1 9000 NEG IMAGE OFF Indicated as when INSTALLATION MODE SS is set e NEGATIVE The user can select positive or negative image SETUP MODE LICENSE PLATE SHUTTER 1 9000 NEG IMAGE OFF EXIT 659 T5Y Negative OFF INSTALLATION MODE e EXIT Enables user to EXIT the OSD menu by using FOCUS VALUE 2 T SELECT If Installation Mode is selected the user can see the screen as below 11 8 Installation Guidelines Camera Height e Must consider height in distance calculation e Sharper angle will alter appearance of plate Horizontal Distance a Capture Distance C Ja b Horizontal Distance Ft2. 8 Installation Guidelines Camera Angles e Both the vertical and the horizontal angle must be less than 30 degrees in order to get an optimal view of the license plate H angle lt 30 X V angle lt 30 V angle less than 30 correct H angle less than 30 correct Capture Zone e Wide angle provides a shorter capture distance e Tele angle provides a longer capture distance What will the plate look like on screen WIDE SETTING 66 5 f 5mm All pictures taken with high beam TELE SETTING 7 4 O f 50mm Position A with WIDE SETTING Position B with WIDE SETTING MM 1M A ona 3 Optimized Capture License Plate Range for S W recongnizable with eyes Position B with TELE SETTING Position C with TELE SETTING 13 8 Installation Guidelines Lane Width e Narrow lanes less variation in plate location e Wider lanes more variation in plate location e Lens should cover entire width of the lane e Ensure that the horizontal field of view is wide enough Narrow lane Easy capture Wider lane Difficult capture Speed e Camera can capture moving vehicles up to 75mph e Keep camera as low as possible e Minimize horizontal angle e Zoom in the lens as close as possible Up to 75 mph 14 8 Installation Guidelines DVR Camera is fully compatible with industry standard DVRs Check compression settings Non conditional refresh compression i e MJPEG or JPEG D1 720x48
3. 0 resolution 30fps each channel for best results 9 Specifications 1 3 960H SONY EXview HAD CCD II Day amp Night 00 IR LED 850nm Power LED 10EA Up to 75mph 120km h License Capture Capture Capture Angle Maximum 30 degree offset 14 F 122 F 10 C 50 C Operating Temperature Heater On ne DC12V 10 Max 700mA Without Heater DC12V 10 Max 1 6A With Heater Power DC12V 10 Max 760mA Without Heater Consumption DC12V 10 Max 990mA With Heater a AC24V 10 Max 9W Without Heater AC24V 10 Max 20W With Heater Approx 1 37Kg Specifications and designs are subject to change for improving the functionality of this product without notice 15 10 Dimensions unit mm M12XP1 25 106 5 125 135 Mount Guide
4. M152 LP751 002 High Contrast License Plate Capture Camera OPERATION MANUAL Thank you for choosing our high guality camera Before attempting to connect or operate this unit please read and follow these instructions Contents A Cautions Important Safety Instructions Features Components Product Diagrams Installation Diagrams Functions Installation Guidelines O OO N O Ci A W N Specifications 10 Dimensions CAUTION These servicing instructions are for use by gualified service personnel only To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are gualified to do so Use Class 2 Power Supply Only 1 Cautions This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Note This eguipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the eguipment is operated in a commercial environment This eguipment generates uses and can radiate radio freguency energy and if not installed and used in accordance with the instruction manual may cause harmf
5. ed all warnings 5 Do not use this apparatus near water 4 Follow all instructions 6 Clean only with dry cloth 7 Do not block any ventilation openings Install in accordance with the manufacturer s instructions 8 Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to EN avoid injury from tip over AI 13 Unplug this apparatus during lightning storms or when unused for long periods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power sup
6. ment L This marking shown on the product or its literature indicates that it should not be disposed with other household wastes at the end of its working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take item for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product should not be mixed with other commercial wastes for disposal CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL This symbol is intended to alert the user to the presence of un insulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock important operating and maintenance servicing instructions This symbol is intended to alert the user to the presence of in the literature accompanying the appliance 2 Important Safety Instruction 1 Read these instructions 2 Keep these instructions 3 He
7. ply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 3 Features e 1 3 960H SONY EXview HAD CCDII e High Resolution 700TV Lines e Special filter and IR LED provides maximum readability despite headlight glare Plate capture up to 75mph 120Km H e 5 0 50 0mm Vari focal lens captures license plate from 16ft 65ft 5M 20M P67 rated Water Proof e Cable concealed bracket e DC12V AC24V Dual power with auto polarity 4 Components LP Camera Video Output Test Cable L Wrench Screws Operation Manual 5 Product Diagrams D Sunshield Cable Concealed Bracket LED 10ea Body CONTROL FUNCTION OSD JOYSTICK 5 Product Diagrams Built in heater protects the camera from low temperatures Operating temperature with Heater 40 C 6 Installation Diagrams e MOUNTING POSITION 6 Installation Diagrams e Monitor Connection DC 12V Power Supply gt DC12V Un VIDEO IN Monitor 0000 DC 12V Power Supply or AC 24V Power Supply DC12V AC24V CJ
8. ul interference to radio communications Operation of this eguipment in a residential area is likely to cause harmful interference in which case the user will be reguired to correct the interference at his own expense WARNING This is a class A product In a domestic environment this product may cause radio interference in which case the user may be reguired to take adeguate measures Caution Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user s authority to operate the eguipment A CAUTION A regulated DC12V 3A power supply is recommended for use with this camera for the best picture and the most stable operation An unregulated power supply can cause damage to the camera When an unregulated power supply is applied the product warranty will be void It is recommended that the camera be used with a monitor that has a CCTV quality 75 video impedance level If your monitor is switched to high impedance then please adjust accordingly Do not attempt to disassemble the camera to gain access to the internal componets Refer servicing to your dealer Never face the camera towards the sun or any bright or reflective light which may cause smears on the picture and possible damage to the image sensor Do not remove the serial sticker for the warranty service 1 Cautions n WEEE Waste Electrical amp Electronic Equip
Download Pdf Manuals
Related Search