Philips HTL2163B
Contents
1. unpack the product and wait until its temperature matches room temperature before connecting it to the power outlet e Parts of this product can be made of glass Handle with care to avoid injury and damage Risk of overheating e Never install this product in a confined space Always leave a space of at least four inches around the product for ventilation Ensure curtains or other objects never cover the ventilation slots on the product Risk of contamination e Do not mix batteries old and new or carbon and alkaine etc e Danger of explosion if batteries are incorrectly replaced Replace only with the same or equivalent type e Remove batteries if they are exhausted or if the remote control is not to be used for a long time e Batteries contain chemical substances they should be disposed of properly Risk of swallowing batteries e The product remote control may contain a coin button type battery which can be swallowed Keep the battery out of reach of children at all times If swallowed the battery can cause serious injury or death Severe internal burns can occur within two hours of ingestion e If you suspect that a battery has been swallowed or placed inside any part of the body seek immediate medical attention e When you change the batteries always keep all new and used batteries out of reach of children Ensure that the battery compartment is completely secure after you replace the battery e Ift2. music vocals in comfort e PERSONAL Personalize the sound based on your preferences Surround sound mode Experience an immersive audio experience with surround sound modes 1 Press SURROUND ON OFF to turn surround mode on or off e On Create a surround listening experience e Off Iwo channel stereo sound Ideal for listening to music Equalizer Change the high frequency treble and low frequency bass settings of the SoundBar 1 Press TREBLE or BASS to change the frequency Synchronize video and sound If the audio and video are not synchronized delay the audio to match the video 1 Press AUDIO SYNC to synchronize the audio with the video Night mode For quiet listening night mode decreases the volume of loud sounds when audio is played Night mode is only available for Dolby Digital soundtracks 1 Press NIGHT to turn night mode on or off Play audio through Bluetooth Through Bluetooth connect the SoundBar with your Bluetooth device such as an iPad iPhone iPod touch Android phone or laptop and then you can listen to the audio files stored on the device through your SoundBar speakers What you need e A Bluetooth device which supports Bluetooth profile AADRAVRCP and with Bluetooth version as 3 0 EDR e The maximum operational range between the SoundBar and a Bluetooth device is approximately 10 meters 30 feet 1 Press Y on the remote control to switch the SoundBar to Blu
3. Always there to help you Register your product and get support at www philips com support FE Contact Philips HIL2163B LLL LLL LL N User manual PHILIPS Contents 1 Important Help and support Safety Care for your product Care of the environment Compliance W UU PND NN NN 2 Your SoundBar Main unit Remote control Connectors U AADA 3 Connect and set up 6 Placement 6 Connect to TV 6 Connect audio from TV and other devices 7 4 Use your SoundBar 8 Adjust the volume 8 Choose your sound 8 Play audio through Bluetooth 9 MP3 player 9 USB storage devices 9 Auto standby 10 Set display brightness 10 Apply factory settings 10 5 Update software 11 Check software version 11 Update software via USB 11 6 Wall mount 12 7 Product specifications Pa 8 Troubleshooting 13 EN 1 Important Read and understand all instructions before you use your product If damage is caused by failure to follow instructions the warranty does not apply Help and support For extensive online support visit www philips com support to e download the user manual and the quick start guide e watch video tutorials available only for selected models e find answers to frequently answered questions FAQs e email us a question e chat with our support representative Follow the instructions on the website to select your language and then enter your product model number Alternatively you can con
4. RC connector on the TV e The HDMI ARC connector on the TV might be labeled differently For details see the TV user manual 2 On your TV turn on HDMI CEC operations For details see the TV user manual e If your TV is not HDMI ARC compliant connect an audio cable to hear the TV audio through your SoundBar see Connect audio from TV and other devices on page 7 e If your TV has a DVI connector you can use an HDMI DVI adapter to connect to TV However some of the features may not be available Connect audio from TV and other devices Play audio from TV or other devices through your Soundbar speakers Use the best quality connection available on your TV Soundbar and other devices Note Option 2 Connect audio through a digital coaxial cable Good quality audio e When your Soundbar and TV are connected through HDMI ARC an audio connection is not required see Connect to TV through HDMI ARC on page 6 DIGITAL IN COAXIAL IN Option 1 Connect audio through a digital optical cable Best quality audio DIGITAL IN OPTICAL 1 Using an optical cable connect the OPTICAL connector on your SoundBar to the OPTICAL OUT connector on the IV or other device e The digital optical connector might be labeled SPDIF or SPDIF OUT 1 Using a coaxial cable connect the COAXIAL connector on your SoundBar to the COAXIAL DIGITAL OUT connector on the TV or other de
5. When HDMI ARC blinks tt indicates that the connected TV is not HDMI ARC compliant or an unsupported audio format is detected Bluetooth A device cannot connect with the SoundBar The device does not support the compatible profiles required for the SoundBar You have not enabled the Bluetooth function of the device See the user manual of the device on how to enable the function The device is not correctly connected Connect the device correctly The SoundBar is already connected with another Bluetooth device Disconnect the connected device then try again Quality of audio play from a connected Bluetooth device is poor The Bluetooth reception is poor Move the device closer to the SoundBar or remove any obstacle between the device and the SoundBar The connected Bluetooth device connects and disconnects constantly 14 The Bluetooth reception is poor Move the device closer to the SoundBar or remove any obstacle between the device and the SoundBar Turn off Wi Fi function on the Bluetooth device to avoid interference For some Bluetooth the Bluetooth connection can be deactivated automatically to save power This does not indicate any malfunction of the SoundBar EN PHILIPS Specifications are subject to change without notice 2014 WOOX Innovations Limited All rights reserved Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N V and are used by WOOX Innova
6. etooth mode L gt BT is displayed on the display panel blinking 2 On the Bluetooth device switch on Bluetooth search for and select PHILIPS HTL2163B to start connection see the user manual of the Bluetooth device on how to enable Bluetooth L gt During connection BT on the display panel blinks 3 Wait until you hear a beep sound from the SoundBar L gt When the Bluetooth connection succeeds BT is displayed on the display panel L gt If the connection fails BT on the display panel blinks continuously 4 Select and play audio files or music on your Bluetooth device e During play if a call is coming music play is paused Play resumes when the call ends e lf your Bluetooth device supports AVRCP profile on the remote control you can press I PI to skip to a track or press PH to pause resume play 5 To exit Bluetooth select other source e When your switch back to Bluetooth mode Bluetooth connection remains active e The music streaming may be interrupted by obstacles between the device and SoundBar such as wall metallic casing that covers the device or other devices nearby that operate in the same frequency e If you want to connect your SoundBar with another Bluetooth device press and hold on the remote control to disconnect the currently connected Bluetooth device MP3 player Connect your MP3 player to play your audio files or music What you need e An MP3 player e A 3 5mm ste
7. he battery compartment cannot be completely secured discontinue use of the product Keep out of reach of children and contact the manufacturer E This is CLASS ll apparatus with double insulation and no protective earth provided Care for your product Use only microfiber cloth to clean the product Care of the environment OY ae Your product is designed and manufactured with high quality materials and components which can be recycled and reused R When this crossed out wheeled bin symbol is attached to a product it means that the product is covered by the European Directive 2002 96 EC Please inform yourself about the local separate collection system for electrical and electronic products Please act according to your local rules and do not dispose of your old products with your normal household waste Correct disposal of your old product helps to prevent potential negative consequences for the environment and human health R Your product contains batteries covered by the European Directive 2006 66 EC which cannot be disposed with normal household waste Please inform yourself about the local rules on separate collection of batteries because correct disposal helps to prevent negative consequences for the environmental and human health Compliance C 0560 This product complies with the radio interference requirements of the European Community Hereby WOOX Innovations declares that this
8. he optical connection COAX Switch your audio source to the coaxlal connection AUDIO IN Switch your audio source to the MP3 connection 3 5mm Jack AUX Switch your audio source to the AUX connection G 4 gt I Previous Next Skip to the previous or next track in USB mode gt HH Play Pause e Start pause or resume play in USB mode BASS Increase or decrease bass Volume control e J Increase or decrease volume e amp Mute or restore volume SOUND Select a sound mode SURROUND ON OFF Select surround or stereo sound AUDIO SYNC Increase or decrease audio delay DIM Set the brightness of SoundBar display panel NIGHT Turn night mode on or off 6 TREBLE Increase or decrease treble Connectors This section includes an overview of the connectors available on your SoundBar an IN 8 DIGITAL IN COAXIAL OPTICAL SUBWOOFER DC IN HDMI OUT ARC TOTV AUX IN L WHITE I R RED o E pS 1 DIGITAL IN COAXIAL Connect to a coaxial audio output on the TV or a digital device AUX IN L R Connect to an analog audio output on the TV or an analog device DIGITAL IN OPTICAL Connect to an optical audio output on the TV or a digital device DC IN Connect to the power supply HDMI OUT ARC TO TV Connect t
9. m 5 25 woofer Dimensions WxHxD 169 240 297 mm Weight 2 5 kg Remote control batteries 1 x AAA RO3 1 5 V 8 Troubleshooting Warning e Risk of electric shock Never remove the casing of the product To keep the warranty valid never try to repair the product yourself If you have problems using this product check the following points before you request service If you still have a problem get support at www philips com support Main unit The buttons on the SoundBar do not work e Disconnect the SoundBar from the power supply for a few minutes then reconnect Sound No sound from SoundBar speakers e Connect the audio cable from your SoundBar to your TV or other devices However you do not need a separate audio connection when the SoundBar and TV are connected through HDMI ARC connection e Reset your SoundBar to Its factory settings e On the remote control select the correct audio Input e Make sure that the SoundBar is not muted Distorted sound or echo e If you play audio from the TV through the SoundBar make sure that the TV is muted Audio and video are not synchronized e Press AUDIO SYNC to synchronize the audio with the video Error message is displayed on the display panel e When ERROR is displayed it indicates that an input audio format is not supported EN 13 When USB ERROR is displayed it indicates that the connected USB device is not supported
10. o the HDMI input on the TV SUBWOOFER Connect to the supplied subwoofer 7 lt gt USB e Audio input from a USB storage device e Upgrade software of this product e Charge a USB device AUDIO IN e Audio input from for example an MP3 player 3 5mm Jack 2 e EN 5 3 Connect and set up This section helps you connect your SoundBar to a IV and other devices and then set it up For information about the basic connections of your SoundBar and accessories see the quick start guide For identification and supply ratings see the type plate at the back or bottom of the product e Before you make or change any connections make sure that all devices are disconnected from the power outlet Placement Place the subwoofer at least 1 meter 3 feet away from your SoundBar and ten centimeters away from the wall For best results place your subwoofer as shown below Connect to TV Connect your SoundBar to a 1V You can listen to audio from TV programs through your SoundBar Use the best quality connection available on your SoundBar and TV Connect to TV through HDMI ARC Your SoundBar supports HDMI with Audio Return Channel ARC If your TV is HDMI ARC compliant you can hear the TV audio through your SoundBar by using a single HDMI cable HDMI OUT ARC 1 Using a High Speed HDMI cable connect the HDMI OUT ARC TO TV connector on your SoundBar to the HDMI A
11. oundBar on the fastening screws 7 Product specifications Note e Specifications and design are subject to change without notice Amplifier e Total output power 120W RMS 0 5 dB 10 THD e Frequency response 20 Hz 20 kHz 3 dB e Signal to noise ratio gt 65 dB CCIR A weighted e Input sensitivity e AUX 900 mV e AUDIO IN 500 mV Audio e S PDIF Digital audio input e Coaxial IEC 60958 3 e Optical TOSLINK USB e Compatibility Hi Speed USB 2 0 e Class support USB Mass Storage Class MSC e File system FAT16 FAT32 NTFS e Supports MP3 and WMA file formats e Sampling frequency s MPSS kaz 1 kHz 12 krz 16 Kriz 22 kHz 24 kHz 32 kHz 44 1 kHz 48 kHz e WMA 44 1 kHz 48 kHz e Constant bit rate e MP3 8 kbps 320 kbps e WMA 32 kbps 192 kbps e Version e WMA V7 V8 V9 Note e This product supports WMA files which are converted via Windows Media Player WMA files converted via other file format converters may not work Main unit Power supply e Model Philips branded AC power adapter DYS602 210309W AS650 210 AA309 e Input 100 240 V 50 60 Hz 1 5 A e Output 21V 3 09A Standby power consumption lt 0 5 W Speaker impedance e Woofer 8 ohm e tweeter 16 ohm Speaker drivers 2 x 90mm 3 5 x 34mm 1 3 woofer 2 x 31mm 1 2 tweeter Dimensions WxHxD 843 x 52 x 60 mm Weight 1 4 kg Subwoofer Impedance 3 6 ohm Speaker drivers 1 x 134 m
12. product is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC You can find the Declaration of Conformity on www p4c philips com Copyright in the U K Recording and playback of material may require consent See Copyright Act 1956 and The Performers Protection Acts 1958 to 1972 EN 3 2 Your SoundBar Congratulations on your purchase and welcome to Philips To fully benefit from the support that Philips offers register your SoundBar at www philips com welcome Main unit This section includes an overview of the main unit Standby On Standby indicator e Switch the SoundBar on or to standby e When the SoundBar is in standby the standby indicator turns red 2 SOURCE Select an input source for the SoundBar G Display panel 4 Volume Increase or decrease volume Remote control This section includes an overview of the remote control a COAX OPTICAL ME y o aux AUDIO IN f Oe en A gm m um Seem Oe OK Na Q 5 OFF SURROUND ON AUDIO SYNC gt DIM NIGHT 1 411 PHILIPS Standby On Switch the SoundBar on or to standby Q Source buttons HDMI ARC Switch your source to HDMI ARC connection 8 Switch to Bluetooth mode USB Switch to USB mode OPTICAL Switch your audio source to t
13. reo audio cable 1 Using the 3 5mm stereo audio cable connect the MP3 player to the AUDIO IN connector on your SoundBar Press AUDIO IN on the remote control UI NY Press the buttons on the MP3 player to select and play audio files or music USB storage devices Enjoy audio on a USB storage device such as an MP3 player and USB flash memory etc What you need e A USB storage device that is formatted for FAT or NTFS file systems and complies with the Mass Storage Class e An MP3 or WMA file on a USB storage device EN 9 1 Connect a USB storage device to this product 2 Press USB on the remote control 3 Use the remote control to control play Button Action gt Il Start pause or resume play I4 I Skip to the previous or next track USB During USB play press repeatedly to select a repeat or shuffle mode or turn off a play mode Note e This product supports WMA files which are converted via Windows Media Player WMA files converted via other file format converters may not work e This product may not be compatible with certain types of USB storage device e If you use a USB extension cable USB HUB or USB multi reader the USB storage device may not be recognized Digital camera PTP and MTP protocols are not supported e Do not remove the USB storage device while it is being read e DRM protected music files MP3 WMA are not supported Support a USB port 5V TA A
14. tact Consumer Care in your country Before you contact note down the model number and serial number of your product You can find this information on the back or bottom of your product Safety Risk of electric shock or fire e Never expose the product and accessories to rain or water Never place liquid containers such as vases near the product If liquids are spilt on or into the product disconnect it from the power outlet immediately Contact Consumer Care to have the product checked before use e Never place the product and accessories near naked flames or other heat sources including direct sunlight e Never insert objects into the ventilation slots or other openings on the product e Where the mains plug or an appliance coupler is used as the disconnect device the disconnect device shall remain readily operable e Disconnect the product from the power outlet before lightning storms e When you disconnect the power cord always pull the plug never the cable Risk of short circuit or fire e Before you connect the product to the power outlet ensure that the power voltage matches the value printed on the back or bottom of the product Never connect the product to the power outlet if the voltage is different Risk of injury or damage to this product e Never place the product or any objects on power cords or on other electrical equipment e If the product is transported in temperatures below 5 C
15. tions Limited under license from Koninklijke Philips N V HTL2163B_05_ UM V2 0
16. ur TV to the HDMI source 5 On the remote control within six seconds press twice then Volume once and then hold down SURROUND ON L gt If an upgrade media is detected on the TV screen you are prompted to start the update gt If an upgrade media is not detected an error message Is displayed on the TV screen Make sure that the latest software of this product is put in the USB storage device 6 Press to start the update 7 Wait until the update Is completed L If the update is complete this product automatically turns off and on again Caution Do not turn off the power or remove the USB storage device when the software update is in progress because you might damage this player EN 11 6 Wall mount EA vote e Improper wall mounting may result in accident injury or damage If you have any query contact Consumer Care in your country Before wall mounting make sure the wall can support the weight of your SoundBar Before wall mount you need not remove the four rubber feet at the bottom of the SoundBar otherwise the rubber feet cannot be fixed back Screw length diameter Depending on the type of wall mounting your SoundBar make sure that you use screws of a suitable length and diameter See the illustration in the quick start guide on how to wall mount the SoundBar 1 Drill two holes on the wall 2 Secure the dowels and screws in the holes 3 Hang the S
17. uto standby When playing media from a connected device the SoundBar automatically switches to standby after 29 minutes of button inactivity and no audio video play from a connected device Set display brightness You can press DIM repeatedly to select a different brightness level of the display panel on this product 10 EN Apply factory settings You can reset this product to the default settings programmed at the factory In any source mode on the remote control press Volume BASS and TREBLE in sequence within three seconds L When the factory settings restore is complete the product automatically switches off and restarts 5 Update software To get the best features and support update your product with the latest software What you need e Connect this product to your TV through HDMI Check software version In HDMI ARC source on the remote control press TREBLE BASS and Volume in sequence Update software via USB 1 Check the latest software version on www philips com support e Search for your model and click on Software and drivers 2 Download the software into a USB storage device Unzip the download if zipped and make sure that the unzipped file is named HTL2163 BIN 2 Put the HTL2163 BIN file in the root directory 3 Connect the USB storage device to the e USB connector on this product 4 Switch this product to the HDMI ARC source and switch yo
18. vice e The digital coaxial connector might be labeled DIGITAL AUDIO OUT Option 3 Connect audio through analog audio cables Basic quality audio 1 Using an analog cable connect the AUX connectors on your SoundBar to the AUDIO OUT connectors on the TV or other device EN 4 Use your SoundBar This section helps you use the SoundBar to play audio from connected devices Before you start e Make the necessary connections described in the quick start guide and the user manual e Switch the SoundBar to the correct source for other devices Adjust the volume 1 Press Volume to increase or decrease a volume level e To mute sound press Mute e To restore the sound press Mute again or press Volume Choose your sound This section helps you choose the Ideal sound for your video or music Sound mode Select predefined sound modes to suit your video or music 1 Press SOUND to select a sound option from the display panel e AUTO Automatically select a sound setting based on the sound stream e POWERFUL Enjoy thrilling arcade sounds ideal for action packed videos and loud parties e BALANCED Experience the original sound of your movies and music without added sound effects e BRIGHT Spice up your dull movies and music with added sound effects e CLEAR Hear every detail in your music and clear voices In your movies e WARM Experience spoken words and
Download Pdf Manuals
Related Search