Bose CineMate 520
Contents
1. English 25 Getting System Information from the Display Understanding messages on the display The display on the front of the console allows you to access the System menu and shows system information and icons Using the System menu Use the System menu to adjust audio levels turn on off features such as AUTO OFF change the language set the coaxial analog and optical inputs for a particular source run ADAPTIQ pair your Acoustimass module with the console or factory reset the system 1 Press BAY on the remote 2 Press and Y to scroll through the System menu 3 Press and gt to adjust the settings 4 Press Qa 1 AUDIO COMP Off Default No change to audio track Enhance dialogue Increases the level of dialogue and sound effects at low volume settings while providing full audio impact at high volume settings Smart volume Reduces the range of volume levels in a movie soundtrack so the difference between extremely loud outbursts and soft sounds is less noticeable 2 AUDIO VIDEO SYNC Adjusts the audio delay to synchronize audio and video 3 HDMI CEC On Default Enables CEC see page 21 Off Disables CEC 4 AUTO OFF Enable Default The system powers off after sixteen minutes of inactivity no sound coming from the system Disable The system will not automatically power off 5 SIDE AUX Audio in Default Sets the Q connector for an auxiliary source Headphones2. Poor or e Remove all protective films from the system distorted e Secure all cable connections on the speakers TV and connected sources e If you see the error message Cannot find Acoustimass Plug in the Acoustimass module Pair the Acoustimass module with the console see If your console cannot find the Acoustimass module e If using the analog or connector decrease the volume on your source e Factory reset the system see page 31 and run the ADAPTiQ audio calibration see page 19 Intermittent Secure all cable connections on the speakers TV and connected sources sound e Move system away from potential interference such as a wireless router cordless phone television microwave etc If your console cannot find the Acoustimass module The Acoustimass module and console are paired at the factory However if you see the error message Cannot find Acoustimass on the display perform this pairing procedure 1 Unplug the Acoustimass module 2 Press BAS on the remote control 3 Press W until 15 PAIR ACOUSTIMASS appears on the display 4 Press Q Plug in Acoustimass appears on the display 5 Plug the AC power cord into an AC mains outlet After the Acoustimass module connects to the console Pairing complete appears on the display 30 English Care and Maintenance Factory reset the system To troubleshoot problems reset the System menu and ADAPTIiQ to th
3. For example corresponds with the BD DVD HDMI connector Your source buttons work with any source that is connected to the corresponding connector If you have a secondary DVD or Blu ray Disc player and connect it to the CBL SAT connector it can be programmed to work with essa If you are using the optical coaxial or analog connectors you must set the input for the appropriate source You can access these settings using the System menu see page 26 24 English Using the System Adjusting the volume On the remote control e Press to increase the volume e Press to decrease the volume e Press to mute or unmute the audio Note If you hear sound coming from your TV see Troubleshooting on page 29 Function buttons The red green yellow and blue buttons on the remote control correspond with the color coded function buttons on your cable satellite box or teletext functions e Cable satellite box functions refer to your cable satellite box owner s guide e Teletext functions correspond with color coded page numbers headings or shortcuts on a teletext display Programming a non Bose remote control You can program a non Bose remote control such as your cable satellite box remote to control the system Refer to your non Bose remote control owner s guide or cable satellite website for instructions Once programmed the non Bose remote controls basic functions such as power on off and volume
4. 6 ft 3 1 8 m of the console e If you have the SoundTouch wireless adapter you can begin set up Refer to the SoundTouch wireless adapter s owner s guide for more information Note Do not connect the adapter to the console until prompted by the SoundTouch app Sample system placement English 9 Setting Up the Acoustimass Module Attaching the rubber feet to the Acoustimass module Attach the rubber feet to the Acoustimass module to protect your floor 1 Turn the Acoustimass module upside down onto a soft surface to protect it from being damaged 2 Attach the rubber feet to the bottom of the Acoustimass module W __ Rubber foot Bottom of Acoustimass module 3 Place the Acoustimass module on its feet Caution Do not place the Acoustimass module on its front back end side or top when in use 4 Remove all protective films These may affect acoustic performance if left in place 10 English Setting Up the Acoustimass Module Connecting the Acoustimass module to power 1 Plug the power cord into the Power connector on the Acoustimass module 2 Plug the power cord into an AC mains outlet English 11 Setting Up the Speakers Connecting the front speakers 1 Insert the front speaker cable s L plug into the left speaker 3 Insert the front speaker cable s R plug into the right speaker 4 Insert the other end of the front speaker cabl
5. IN and OUT audio connector panels use audio OUT Audio only sources If your audio only source such as a media or CD player is non HDMI compatible connect it to the console s optical coaxial or analog connector You can use an optical coaxial or analog cable available separately Note After connecting your audio only source you must set the optical coaxial or analog input for the appropriate source You can access these settings using the System menu see page 26 Connecting the console to power 1 Plug the power cord into the Power my connector on the console 2 Plug the power cord into an AC mains outlet 16 English Starting Up the System Installing the remote control s batteries 1 Slide open the battery compartment cover on the back of the remote control 2 Insert the two provided AA IEC LR6 1 5V batteries Match the and symbols on the batteries with the and markings inside the compartment 3 Slide the battery compartment cover back into place Powering on the system Press on the remote The console powers on The display defaults to CBL SAT for first time power on Otherwise the display defaults to your last used source Note The system powers off after sixteen minutes of inactivity You can disable AUTO OFF using the System menu see page 26 English 17 Finishing Setup Checking for sound 1 2 Power on your TV If you are using a cable satellite bo
6. an optical coaxial or analog stereo audio cable Without this secondary connection you may not hear audio from the Bose system Use a secondary connection in the following configurations e You are using internal sources such as Internet applications or an over the air antenna e You are connecting sources to your TV Refer to your TV owner s guide for more information Tip If your TV has IN and OUT audio connector panels use audio OUT for your secondary connection Connecting the console to other sources You can connect the console to other sources such as a cable satellite box DVD or Blu ray Disc player or game system with an HDMI cable available separately If your source is non HDMI compatible use different audio and video cables see page 16 1 Insert one end of an HDMI cable into your source s HDMI OUT connector 2 Insert the other end of an HDMI cable into the appropriate HDMI connector on the console For example to connect a game system connect an HDMI cable to the GAME connector Connect other sources to the appropriate HDMI connector on the console e e ee BO PT ooo on e English 15 Setting up the Console Connecting to non HDMI compatible sources If your source is non HDMI compatible connect it to your TV using audio and video cables available separately Refer to your TV owner s guide for more information Tip If your source has
7. are trademarks of the Blu ray Disc Association HDMI is a trademark or registered trademark of HDMI Licensing LLC in the United States and other countries O DOLBY Manufactured under license from Dolby Laboratories Dolby and the double D symbol are DIGITAL trademarks of Dolby Laboratories dits Manufactured under license under U S Patent s 5 956 674 5 974 380 and 6 487 535 amp other Digital Sureund worldwide patents issued amp pending DTS the DTS Symbol and DTS the DTS Symbol are registered trademarks amp the DTS logos are trademarks of DTS Inc Product includes software 2010 DTS Inc All Rights Reserved SoundTouch and the wireless note design are trademarks of Bose Corporation in the U S and other countries Wi Fi is a registered mark of the Wi Fi Alliance 2014 Bose Corporation No part of this work may be reproduced modified distributed or otherwise used without prior written permission 4 English Contents Introduction About your CineMate 520 home theater system iii 7 System FEGtUrest c arredi fiala 7 Introducing SoundTouch from BOSE cscseseseeseeseeeeeeetseeeeeeeeeeteteseeeeeeeneeeeeees 7 UnpackingtheSysterm nani ere acento Lie aiar 8 Placement guidelines ss RM A Au 9 Sample systemiplacement i rate ia eaves 9 Setting Up the Acoustimass Module Attaching the rubber feet to the Acoustimass module 10 Connecting the Acoustimass module to po
8. be discarded as household waste and should SK recycling helps protect natural resources human health and the environment For more Pere mmm information on disposal and recycling of this product contact your local municipality disposal service or the shop where you bought this product English 3 Important Safety Information Names and Contents of Toxic or Hazardous Substances or Elements Toxic or Hazardous Substances and Elements Part Name Lead Mercury Cadmium Hexavalent Polybrominated _ Polybrominated Pb Hg Cd CR VI Biphenyl PBB diphenylether PBDE PCBs X O O O O O Metal parts X O O O O O Plastic parts O O O O O O Speakers X O O O O O Cables X O O O O O O Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement in SJ T 11363 2006 X Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement in SJ T 11363 2006 Please complete and retain for your records Serial numbers can be found on the Acoustimass module s connector panel and on the packaging for the remote control Module serial number Remote serial number Console serial number Purchase date We suggest you keep your receipt with this owner s guide Blu ray Disc and Blu ray
9. to the contact sheet in the carton 8 English Introduction Placement guidelines To avoid wireless interference keep other wireless equipment away from the system Place the system outside of and away from metal cabinets away from other audio video components and away from direct heat sources Acoustimass module e Stand the Acoustimass module on its rubber feet along the same wall as your TV or along any other wall in the front third of the room e Choose a stable and level surface Vibration can cause the Acoustimass module to move particularly on smooth surfaces like marble glass or highly polished wood e Make sure there is an AC mains outlet nearby Front speakers e Place one speaker to the left and one speaker to the right of the TV e Keep each speaker within 3 ft 1 m of the TV if possible e If placing the speakers in an enclosed bookcase shelf position them at the front edge of the shelf Center speaker e Place the center speaker on a stable and level surface directly above or below your TV Rear speakers e Place the rear speakers toward the back of the room behind you at ear height when seated or higher if possible Console SoundTouch wireless adapter available separately e Place the console near your TV Do NOT place the TV on top of your console e Make sure there is an AC mains outlet nearby e Place the SoundTouch wireless adapter within 1
10. IIS EE nn CineMate 520 home theater system Owner s Guide Guia del usuario Notice d utilisation Important Safety Information Please read this owner s guide carefully and save it for future reference The lightning flash with arrowhead symbol within an equilateral triangle alerts the user to the presence of uninsulated dangerous voltage within the system enclosure that may be of sufficient magnitude to constitute a risk of electric shock The exclamation point within an equilateral triangle alerts the user to the presence of important operating and maintenance instructions in the owner s guide WARNINGS eTo reduce the risk of fire or electric shock do not expose this product to rain or moisture Do not expose this apparatus to dripping or splashing and do not place objects filled with liquids such as vases on or near the apparatus As with any electronic products use care not to spill liquids into any part of the product Exposure to liquids may create a failure and or fire hazard Replace only with a AA IEC LR06 alkaline battery or batteries Do not place naked flame sources such as lighted candles on or near the product CAUTIONS A Do not make unauthorized alterations to the product doing so may compromise safety regulatory compliance system performance and may void the warranty eLong term exposure to loud music may cause hearing damage It is best to avoid extreme volume when using headpho
11. Sets the Q connector as a headphones input Note If set to Headphones input and a cable is connected the speakers are muted Disconnect your headphones when not in use 6 BASS LEVEL Adjusts bass level 7TREBLE LEVEL Adjusts treble level 8 CENTER LEVEL Increases or decreases the level of dialogue for movies and TV 26 English Getting System Information from the Display 9 SURROUND LEVEL Adjusts the volume of the rear speakers relative to front speakers 10 LANGUAGE t Changes the language on the console and ADAPTIQ 11 SET OPTICAL INPUT Sets the optical connector to Auto TV Default CBL SAT BD DVD GAME or AUX source 12 SET COAXIAL INPUT Sets the coaxial connector to Auto TV Default CBL SAT BD DVD GAME or AUX source 13 SET ANALOG INPUT Sets the analog connector to Auto TV Default CBL SAT BD DVD GAME or AUX source 14 ADAPTIQ Starts the ADAPTIQ audio calibration process 15 PAIR ACOUSTIMASS Reconnects the Acoustimass module to the system 16 FACTORY RESET Sets the System menu and ADAPTIQ to the factory settings English 27 Getting System Information from the Display Error messages Display System state ERROR The Acoustimass module is not connected to Cannot find Acoustimass the console lt SOURCE gt The source is not connected to the console or the No signal source is connected to the console and powered off SIDE AUX The s
12. The system supports Consumer Electronics Control CEC CEC allows you to control multiple HDMI connected sources without programming the remote You can turn on off CEC using the System menu See page 26 Your source may support CEC but refer to it with a different name Refer to your source owner s guide for more information CEC controls sources connected to the console s HDMI connectors Er CBL SAT BD DVD 6 Do BE ooo o Do Tip You may need to use your source s system menu to enable CEC Refer to your source owner s guide for more information English 21 Using the System Test your HDMI connected sources for CEC Test each of your sources for CEC using the remote control Note Your HDMI connected source may not support CEC Refer to your source owner s guide for more information 1 Power off the Bose system 2 Prepare your source e lf you are testing your TV power off your TV e If you are testing another source power off the source Power on your TV 3 Press the button for the source you are testing CBL SAT j BD DVD came ES The source button glows The source and system power on 4 To ensure your source works properly with your remote control press a variety of buttons that correspond with your source s functions If your source does not perform one of the functions program the remote control see page 23 22 English Using the Sys
13. Wer iii Ill Setting Up the Speakers Connecting the frontSpeakers crari aiar 12 Connecting th Fear Speakers coli 13 Wall mounting the speakers inner 13 Setting Up the Console Connecting the console to your TV s HDMI ARC connector 14 TVs without an HDMI ARC connector 15 Use a secondary connection in the following configurations 15 Connecting the console to other sources 15 Connecting to non HDMI compatible sources 16 Audio only SOUIGES irnn as nt ner eee hairiest 16 Connettinptheconsoleto poW eli lt rsrasiiii lana 16 Starting Up the System Installing the remote control s batteries ii 17 Powering on tne SYSTem ss abolire iu 17 Finishing Setup Checking for sound anaa Lalli 18 Changing the language on the console 18 Running the ADAPTIQ audio calibration 19 English 5 Contents Using the System Remote control DUELtOns iir aaa 20 Programming the universal remote control 21 Consumer Electronics Control 12 Test your HDMI connected sources for CEC scececesceseceseteeeeseeeeeeeeseeeeeseeeeneeeaees 22 Program the remote to control YOUF SOUrCE 23 Source S l CtiON cipria 24 Select a source connected to the Bose system 24 Select a source connected to your TV iii 24 Universal source buttons and console connectors 24 Adjusting the Volume ernie NPA nn en A e nee 25 Function DUON Serna n
14. block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 Protect the power supply or cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 10 Only use attachments accessories specified by the manufacturer 11 Unplug this apparatus during lightning storms or when unused for long periods of time 12 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply or cord is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does caus
15. e factory settings 1 2 3 4 Press BAL on the remote control Press W until 16 FACTORY RESET appears on the display Press 5 The system resets Run the ADAPTIQ audio calibration see page 19 Reset a source button on the remote control If you are experiencing problems with a source button on the remote control reset the source button to the factory settings After performing this procedure your source button is in CEC mode 1 2 On the remote control press and hold the appropriate source button until all six source buttons glow then release Only the appropriate source button glows On the number keypad enter 0140 Service connectors on the Acoustimass module The Service and Data connectors are for service use only Do not insert any cables into these connectors English 31 Care and Maintenance Cleaning e Clean the surface of the system with a soft dry cloth e Do not use any sprays near the system Do not use any solvents chemicals or cleaning solutions containing alcohol ammonia or abrasives e Do not allow liquids to spill into any openings Customer service For additional help contact Bose Customer Service Refer to the contact sheet in the carton Limited warranty Your system is covered by a limited warranty Details of the limited warranty are provided on the product registration card that is in the carton Please refer to the card for instructions on h
16. e harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Changes or modifications not expressly approved by Bose Corporation could void the user s authority to operate this equipment This device complies with part 15 of the FCC Rules and Industry Canada license exempt RSS standard s Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This Class B digital apparatus complies with Canadian ICES 003 CAN ICES 3 B NMB 3 B This device complies with FCC and Industry Canada RF radiation exposure limits set forth for general population It must not be co located or be operating in conjunction with any other antennas or transmitters The temperature range of this product is 32 F 0 C to 113 F 45 C be delivered to an appropriate collection facility for recycling Proper disposal and This symbol means the product must not
17. e for basic functions see step 6 in Program the remote to control your source Repeat steps 1 and 2 until your source responds Press QM to save your settings Note Your source may not be compatible with universal remote controls Refer to your source owner s guide for more information English 23 Using the System Source selection You can switch between sources by pressing the appropriate source button on the remote control Before you begin program the remote to control your source see page 23 Select a source connected to the Bose system If your source is connected to the console and does not use CEC follow this procedure to set the console to the appropriate mode and turn on the source 1 Power on the system 2 Press the button for the source you want to control The source button glows 3 Press i The source powers on Select a source connected to your TV If your source is connected to your TV follow this procedure to select the appropriate TV input 1 Power on the system your TV and the appropriate source 2 Press to select the correct input on your TV You may need to press several times to select the TV input for the source On some TVs displays a menu Use the remote control to choose the correct TV input and close this menu Universal source buttons and console connectors The source buttons on your remote control correspond with the connectors on the back of the console
18. e into the 6 pin Speaker Connections connector on the console 12 English Setting Up the Speakers Connecting the rear speakers 1 Insert the rear speaker cable s LR plug into the left rear speaker 2 Insert the rear speaker cable s RR plug into the right rear speaker 3 Insert the other end of the rear speaker cable into the 4 pin Speaker Connections connector on the console Wall mounting the speakers You can mount the speakers on wall brackets floor stands or table stands To purchase these accessories contact your local Bose dealer or visit www Bose com CAUTION Do not use any other hardware to mount the speakers English 13 Setting Up the Console Connecting the console to your TV s HDMI ARC connector Use the Bose HDMI cable to connect the console to your TV 1 Disconnect your HDMI connected sources such as a cable satellite box DVD or Blu ray Disc player or game system from your TV 2 Insert one end of the Bose HDMI cable into the TV connector on the console 3 Insert the other end of the HDMI cable into your TV s HDMI connector Note Use your TV s HDMI connector labeled ARC or Audio Return Channel if available If your TV does not have an HDMI ARC connector see page 15 14 English Setting Up the Console TVs without an HDMI ARC connector If your TV does not have an HDMI ARC connector you may need to make a secondary connection to the console with
19. n mon en alal 25 Programming a non Bose remote control 25 Getting System Information from the Display Understanding messages on the display Using the System MENU MA M Maree Manas Error MESSAGES ENS io RE en NS pie Acoustimass module status indicator ii 28 Care and Maintenance TroUbDIeSROGTINE 2e ae ner Alana est dede etienne nel 29 If your console cannot find the Acoustimass module 30 Factory reset the syste Missierna ea E ail esi 31 Reset a source button on the remote control 31 Service connectors on the Acoustimass module 31 EN AGMA ER iaia 32 US LONE TS CIV ICE ces carati aiar ei 32 Limited Warranty siana a iii 32 T chnicalinf matins r iraa a locato 32 6 English Introduction About your CineMate 520 home theater system The CineMate 520 system delivers spacious true 5 1 surround sound from small high performance speakers for consistent audio performance regardless of content source or room layout System Features e Advanced Bose audio processing provides natural and lifelike sound e ADAPTiQ audio calibration optimizes sound quality e Display provides access to system settings and information e HDMI connectivity allows easy setup and ensures high quality audio from your connected sources e Supports Consumer Electronics Control CEC e Programmable universal remote can control your TV cable satellite box and other connected sources e Hideaway wireless Acoustima
20. nes especially for extended periods WARNING LS Contains small parts which may be a choking hazard Not suitable for children under age 3 WARNING This product contains magnetic material Contact your physician if you have questions on whether this might affect the operation of your implantable medical device NOTES e The product label is located on the bottom of the console e Where the mains plug or appliance coupler is used as the disconnect device such disconnect device shall remain readily operable e This product must be used indoors It is neither designed nor tested for use outdoors in recreational vehicles or on boats e The speaker wire and interconnect cables included with the system are not approved for in wall installation Please check your local building codes for the correct type of wire and cable required for in wall installation and other relevant provisions of Directive 1999 5 EC and all other applicable EU directive C Bose Corporation hereby declares that this product is in compliance with the essential requirements requirements The complete declaration of conformity can be found at www Bose com compliance 2 English Important Safety Information Important Safety Instructions ONDN FWP 1 Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with a dry cloth Do not
21. onnected to your TV select the correct TV input see page 24 e Disconnect headphones when not in use e If connecting your source through the Q connector enable Audio in using the System menu see page 26 A e If you are connecting headphones to the connector enable Headphones using the System menu see page 26 e If you see the error message Cannot find Acoustimass pair the Acoustimass module with the console see page 30 e Factory reset the system see page 31 Sound is coming from your TV speakers Remote control is inconsistent or does not work e Insert the HDMI cable into a connector on your TV labeled ARC or Audio Return Channel if available e Turn off your TV speakers refer to your TV owner s guide e Decrease your TV volume to its lowest setting e Match the and symbols on the batteries with the and markings inside the compartment See page 17 e Replace the battery see page 17 e Press the volume button on the remote control and see if the correct source button flashes e If using CEC Point the remote control at the console Program the remote to control your source see page 23 e If you have programmed the remote to control your source Point the remote control at the appropriate source Ensure you have entered the correct code for your source s brand Program the remote with another code see page 23 English 29 Care and Maintenance
22. ource is not connected to the Q connector on Nothing connected the console ERROR Call Bose customer service Refer to the contact Call Bose sheet in the carton Acoustimass module status indicator The status indicator on the back of the Acoustimass module provides information on system activity Indicator activity Acoustimass module state Amber Connected to the console Blinking amber Disconnected from the console Slow blinking amber Available to make a wireless connection to the console Red System error 28 English Care and Maintenance Troubleshooting No power e Secure the Acoustimass module s and console s power cords e Reconnect the Acoustimass module s and console s power cords firmly into an AC mains outlet e Use the remote control to power on the system e Factory reset the system see page 31 No sound e Unmute the system e Increase the volume e Plug the Acoustimass module and console into a live AC mains outlet e Insert the HDMI cable into a connector on your TV labeled ARC or Audio Return Channel If your TV does not have an HDMI ARC connector use a secondary audio cable in addition to the HDMI cable see page 15 e If using a secondary audio cable insert the cable into a connector on your TV labeled Output or OUT not Input or IN e Secure all cable connections on the speakers TV and connected sources e If your source is c
23. ow to register Failure to register will not affect your limited warranty rights The warranty information provided with this product does not apply in Australia and New Zealand See our website at www bose com au warranty or www bose con nz warranty for details of the Australia and New Zealand warranty Technical information Acoustimass module Power rating 100 240V U 50 60Hz 150W Console Power rating 100 240V VU 50 60Hz 60W 32 English Care and Maintenance English 33 IDE 2014 Bose Corporation The Mountain Framingham MA 01701 9168 USA AM715113 R v 00 F15113 0010
24. rmine optimal sound quality Insert the ADAPTIQ headset cable into the z connector on the console Press RO on the remote control Press W until 14 ADAPTIQ appears on the display Press Follow the voice prompts until the system completes the process Unplug the ADAPTiQ headset from the console and store it in a safe place Note If you move the system or any furniture run ADAPTIQ again to ensure optimal sound quality English 19 Using the System Remote control buttons Use the remote to control sources connected to your system adjust the system volume change channels use playback functions enable cable satellite box functions and navigate the System menu F Toggles between SoundTouch AE ESS EE available separately Source selection as and 5 connector TV F AUX Selects a source Powers on off the connected to ACER Duse Bose system your TV L Powers on off a selected source Navigation pad Lists recorded Displays the Internet DVR programs E TV home page System menu Previous channel chapter or track Playback controls TV aspect ratio Teletext mode Function buttons Closed captioning see page 25 20 English Using the System Programming the universal remote control You can use the remote to control your TV cable satellite box DVD or Blu ray Disc player game system DVR or other auxiliary source Consumer Electronics Control
25. ss module provides impactful bass sound e Speakers can be mounted on the wall or floor stands kit available separately e Supports the SoundTouch wireless adapter available separately Introducing SoundTouch from Bose With the SoundTouch wireless adapter available separately you can stream Internet radio music services where available and your music library If you have Wi Fi at home you re ready to enjoy your favorite music in any room you want Key Benefits e Enjoy wireless access to Internet radio music services and your music library e Stream your favorite music easily with personalized Presets e Works with your existing Wi Fi network e Free SoundTouch app for your computer smartphone or tablet provides more powerful control e Simply add additional systems at any time for a multi room listening experience e Wide selection of Bose audio systems lets you choose the right solution for any room English 7 Introduction Unpacking the system Carefully unpack the carton and confirm that the following parts are included D Center speaker LU Lo A Acoustimass Console power cord HDMI cable ADAPTIQ headset power cord amp Universal remote control Rubber feet 0 The appropriate power cords for your region are supplied Note If part of the system is damaged do not use it Contact your authorized Bose dealer or Bose customer service Refer
26. tem Program the remote to control your source If your source does not support CEC you can program the remote to control your source 1 2 3 Power on your source Locate the code for your source s brand in the Universal Remote Device Codes book provided On the remote control press and hold the appropriate source button until all six source buttons glow then release For example to program your TV press and hold iv _ Only the appropriate source button glows On the number keypad enter the code for your source s brand Note If all six buttons blink three times you entered an invalid code Repeat steps 3 and 4 Press on the volume button Test the source for basic functions e TV press the channel buttons Press SE The settings menu appears Press and to navigate e Cable satellite box press SW The programming guide appears Press and gt to navigate e DVD or Blu ray Disc player press Cy The settings menu appears Press and P to navigate e Game system press and to navigate through your menu If your source responds to basic functions press amp to save your settings If your source does not respond Use the remote control s code scanner to find the code for your source 1 2 3 4 Press on the volume button to try another code Note If all six buttons blink three times you have cycled through all codes for your source Test the sourc
27. x or other secondary source power on this source Tip If your secondary source is connected to your TV select the appropriate TV input You may need to use a different remote Power on the system Press the appropriate source button Check if sound is coming from the Bose speakers Note If you do not hear sound from the Bose speakers see Troubleshooting on page 29 Press NG on the remote control Check that no sound is coming from the TV speakers Note If you hear sound coming from your TV speakers see Troubleshooting on page 29 Changing the language on the console Use the remote control to change the language on the console 1 2 3 Power on the system Press RQ on the remote control Press W until 10 LANGUAGE appears on the display d CI 10 LANGUAGE English v 4 Press lt and gt to select your language 5 Press nb Tip Look for the t icon in the System menu if you select the wrong language 18 English Finishing Setup Running the ADAPTiQ audio calibration The ADAPTIQ audio calibration customizes the sound of the system to the acoustics of your listening area by taking five audio measurements To perform an audio calibration you need 10 minutes when the room is quiet 1 NOGARO N Put the ADAPTIQ headset on your head During the ADAPTIQ audio calibration a microphone on the top of the headset measures the sound characteristics of your room to dete
Download Pdf Manuals
Related Search