Kramer Electronics TP-582T
Contents
1. ACTUAL PURCHASE PRICE PAID FOR THE PRODUCT TO THE MAXIMUM EXTENT PERMITTED BY LAW KRAMER ELECTRONICS IS NOT RESPONSIBLE FOR DIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR CONDITION OR UNDER ANY OTHER LEGAL THEORY Some countries districts or states do not allow the exclusion or limitation of relief special incidental consequential or indirect damages or the limitation of liability to specified amounts so the above limitations or exclusions may not apply to you Exclusive Remedy TO THE MAXIMUM EXTENT PERMITTED BY LAW THIS LIMITED WARRANTY AND THE REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES REMEDIES AND CONDITIONS WHETHER ORAL OR WRITTEN EXPRESS OR IMPLIED TO THE MAXIMUM EXTENT PERMITTED BY LAW KRAMER ELECTRONICS SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IF KRAMER ELECTRONICS CANNOT LAWFULLY DISCLAIM OR EXCLUDE IMPLIED WARRANTIES UNDER APPLICABLE LAW THEN ALL IMPLIED WARRANTIES COVERING THIS PRODUCT INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL APPLY TO THIS PRODUCT AS PROVIDED UNDER APPICABLE LAW IF ANY PRODUCT TO WHICH THIS LIMITED WARRANTY APPLIES IS A CONSUMER PRODUCT UNDER THE MAGNUSON MOSS WARRANTY ACT 15 U S C A 2301 ET SEQ OR OTHER APPICABLE LAW THE FOREGOING DISCLAIMER OF IMPLIED WARRANTIES SHAL2. Connects to a network 7 RS 232 9 pin D sub Connector Connects to an RS 232 port 8 5V DC 5V DC connector for powering the unit 9 R 3 5mm Mini Jack Connector Connects to an external infrared transmitter sensor receiver 10 INLED Lights when an input device is connected 11 OUT 1 LED Lights when the HDMI 1 output device is connected 12 OUT 2LED Lights when the HDMI 2 output device is connected 13 LINK LED Lights when the TP connection is active 14 ONLED Lights when receiving power KRAMER SIMPLE CREATIVE TECHNOLOGY Connecting the TP 581T TP 582T and TP 582R 5 Connecting the TP 581T TP 582T and TP 582R You can use the TP 581T HDMI Line Transmitter or the TP 582T HDMI Switcher Line Transmitter with the TP 582R HDMI Line Receiver DA to configure an HDMI transmitter receiver system e Toconnect the TP 582T or TP 581T see Section 5 1 e Toconnect the TP 582R see Section 5 2 e To remotely control the A V equipment see Section 5 3 5 1 Connecting the TP 582T or TP 581T To connect the TP 582T or TP 581T as shown in the example in Figure 4 do the following 1 Connect the HDMI IN1 connector to the first HDMI source for example a DVD player 1 for the TP 582T 2 Connect the HDMI IN2 connector to the second HDMI source for example a DVD player 2 3 Connect the ETHERNET RJ 45 connector to a network 4 Connect the RS 232 9 pin D sub connector to a computer 5 Connect the IR 3 5mm mini jack to a
3. sub rear panel port on the transmitter receiver system unit via a 9 wire straight cable pin 2 to pin 2 pin 3 to pin 3 pin 5 to pin 5 to the RS 232 9 pin D sub port on your PC 14 KRAMER SIMPLE CREATIVE TECHNOLOGY Connecting the TP 581T TP 582T and TP 582R 5 6 Wiring the RJ 45 Connectors This section defines the TP pinout using a straight pin to pin cable with RJ 45 connectors Note that the cable Ground shielding must be connected soldered to the connector shield EIA TIA 568B Figure 8 TP PINOUT PIN Wire Color 1 Orange White Green White e Green re eom A 15 Connecting the TP 581T TP 582T and TP 582R 5 7 Acquiring the EDID To acquire the EDID connect the transmitter and receiver system as described in Section 5 Once the power is connected the system acquires the EDID according to the following priorities e If only one output is connected the EDID will be acquired from that output e If both outputs are connected the EDID will be acquired from the output connected to HDMI OUT 1 e Ifno output is connected the default EDID is acquired To acquire the EDID of a newly connected output 1 Disconnect the power on the TP 582R 2 Connect the new acceptor to HDMI OUT 1 if two outputs are connected 3 Connect the power The EDID is acquired only if the power is disconnected and then reconnected KRAMER SIMPLE CREATIVE TECHNOLOGY
4. Kramer Electronics Ltd USER MANUAL Models TP 581T HDMI Line Transmitter TP 582T HDMI Switcher Line Transmitter TP 582R HDMI Line Receiver DA Contents Contents 1 Introduction 2 Getting Started 2 1 Quick Start 3 Overview 3 1 Features of the TP 581T TP 582T and TP 582R 3 2 About HDBaseT Technology 3 3 Using Twisted Pair Cable 3 4 Recommendations for Achieving the Best Performance 3 5 Safety Instructions 3 6 Recycling Kramer Products 4 Your HDMI Line Transmitters Receiver 4 1 Your TP 581T HDMI Line Transmitter 4 2 Your TP 582T HDMI Switcher Line Transmitter 4 3 Your TP 582R HDMI Line Receiver DA 5 Connecting the TP 581T TP 582T and TP 582R 5 1 Connecting the TP 582T or TP 581T 5 2 Connecting the TP 582R 5 3 Controlling the A V Equipment via an IR Transmitter 5 4 Controlling the TP 582T via the REMOTE Terminal Block Connector 5 5 Connecting to a PC 5 6 Wiring the RJ 45 Connectors 5 7 Acquiring the EDID 6 Technical Specifications 7 Default EDID Figures Figure 1 TP 581T HDMI Line Transmitter Figure 2 TP 582T HDMI Switcher Line Transmitter Figure 3 TP 582R HDMI Line Receiver DA Figure 4 Connecting the TP 582T TP 582R Transmitter Receiver Figure 5 Controlling a DVD Player via the TP 582R Figure 6 Controlling an LCD Display via the TP 582T Figure 7 Connecting the Contact Closure Remote Control PINs Figure 8 TP PINOUT Tables Table 1 TP 581T HDMI Line Transmitter Features Tab
5. L NOT APPLY TO YOU AND ALL IMPLIED WARRANTIES ON THIS PRODUCT INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR THE PARTICULAR PURPOSE SHALL APPLY AS PROVIDED UNDER APPLICABLE LAW Other Conditions This limited warranty gives you specific legal rights and you may have other rights which vary from country to country or state to state This limited warranty is void if i the label bearing the serial number of this product has been removed or defaced ii the product is not distributed by Kramer Electronics or iii this product is not purchased from an authorized Kramer Electronics reseller If you are unsure whether a reseller is an authorized Kramer Electronics reseller please visit our Web site at www kramerelectronics com or contact a Kramer Electronics office from the list at the end of this document Your rights under this limited warranty are not diminished if you do not complete and return the product registration form or complete and submit the online product registration form Kramer Electronics thanks you for purchasing a Kramer Electronics product We hope it will give you years of satisfaction 20 KRAMER SIMPLE CREATIVE TECHNOLOGY For the latest information on our products and a list of Kramer distributors visit www kramerelectronics com where updates to this user manual may be found We welcome your questions comments and feedback Safety Warning Disconnect the unit from the power supply befor
6. RE 10 two IR Emitter Extension Cables are also available a 15 meter cable and a 20 meter cable 12 KRAMER SIMPLE CREATIVE TECHNOLOGY Connecting the TP 581T TP 582T and TP 582R Figure 6 illustrates how to control the LCD display via the TP 581T TP 582T TP 582T External IR Sensor CD Display IR Transmitter IR Emitter LCD Display with Speakers IR Emitter Figure 6 Controlling an LCD Display via the TP 582T Connecting the TP 581T TP 582T and TP 582R 5 4 Controlling the TP 582T via the REMOTE Terminal Block Connector The contact closure remote control pins operate in a similar way to the INPUT SELECT button Using the contact closure remote control you can select the HDMI input To do so momentarily connect the required input pin IN 1 or IN2 on the REMOTE CONTROL terminal block connector to the GND Ground pin as Figure 7 illustrates Do not connect more than one PIN to the GND PIN at the same time 5 5 REMOTE REMOTE CONTROL CONTROL To select input 1 To select input 2 momentarily connect momentarily connect the 1 PIN to the G PIN the 2 PIN to the G PIN Figure 7 Connecting the Contact Closure Remote Control PINs Connecting to a PC You can connect to the transmitter receiver system via an RS 232 connection using for example a PC Note that a null modem adapter connection is not required To connect via RS 232 connect the RS 232 9 pin D
7. Technical Specifications 6 Technical Specifications Table 4 includes the technical specifications Table 4 Technical Specifications of the TP 581T TP 582T and TP 582R TP 581T TP 582T TP 582R INPUTS 1 HDMI connector 2 HDMI connectors 1 RJ 45 connector 1 remote contact closure on a terminal block connector OUTPUTS 1 RJ 45 connector 1 RJ 45 connector 2 HDMI connectors 1 TOSLINK optical audio 1 S PDIF in an RCA connector PORTS 1 IR on a 3 5mm mini jack 1 IR on a 3 5mm mini jack 1 IR on a 3 5mm mini jack 1 Ethernet 100BaseT on 1 Ethernet 100BaseT on 1 Ethernet 100BaseT on an RJ 45 connector an RJ 45 connector an RJ 45 connector 1 RS 232 on a 9 pin D sub 1 RS 232 on a 9 pin D sub 1 RS 232 on a 9 pin D sub connector connector connector BANDWIDTH Supports up to 2 25Gbps bandwidth per graphic channel COMPLIANCE WITH Supports HDMI and HDCP HDMI STANDARD POWER SOURCE 5V DC 800mA 5V DC 800mA 5V DC 1 55A DIMENSIONS 18 8cm x 11 4cm x 2 4cm 7 4 x 4 5 x 1 0 W D H WEIGHT 0 6kg 1 4lbs ACCESSORIES Power supply OPTIONS RK T2B 19 rack mount Kramer BC HDKat6a cable 1 Specifications are subject to change without notice 17 Default EDID 7 Default EDID The factory default EDID is listed below Monitor Model name Manufacturer KRM5820 505 707455010 2009 ISO week 10 None EDID revision 1 3 Input sign
8. adapter to the mains electricity not shown in Figure 4 KRAMER SIMPLE CREATIVE TECHNOLOGY Connecting the TP 581T TP 582T and TP 582R TP 582T External IR Transmitter DVD 1 Lapto IR af DVD 1IR External Transmitter S 1V9 Sensor TP 582R RS 232 P Z T h Projector lt SiPDIF LCD Display LCD Display Digital Audio with Speakers with Speakers Recorder Player Figure 4 Connecting the TP 582T TP 582R Transmitter Receiver 11 Connecting the TP 581T TP 582T and TP 582R 5 3 Controlling the A V Equipment via an IR Transmitter Since the IR signal on the TP 581T TP 582T and the TP 582R is bidirectional you can use a remote control transmitter to send commands to the A V equipment from either end of the transmitter Receiver system To do so you have to use the Kramer external IR sensor and the Kramer IR emitter cable Note that the IR sensor is only used to select the TP 582T inputs These IR signals cannot be transmitted to the TP 582R Figure 5 illustrates how to control the DVD player using a remote control via the TP 582R IR Emitter DVD 1IR Transmitter DVD 1 Figure 5 Controlling a DVD Player via the TP 582R 1 That is used for controlling a peripheral device for example a DVD player The Kramer IR remote control transmitter supplied with the TP 582 is used to select the inputs of the machine 2 PIN 95 0104050 3 P N C A35 I
9. ailable where appropriate i Go to http www kramerelectronics com support product_downloads asp 1 GROUP 1 Distribution Amplifiers GROUP 2 Switchers and Matrix Switchers GROUP 3 Control Systems GROUP 4 Format Standards Converters GROUP 5 Range Extenders and Repeaters GROUP 6 Specialty AV Products GROUP 7 Scan Converters and Scalers GROUP 8 Cables and Connectors GROUP 9 Room Connectivity GROUP 10 Accessories and Rack Adapters GROUP 11 Sierra Products 2 Download up to date Kramer user manuals from the Internet at http www kramerelectronics com Getting Started 2 1 Quick Start This quick start chart summarizes the basic setup and operation steps Step 1 Connect the machine see section 5 Connect the CAT 5 input and output Connect the HDMI input Connect the IR emitters sensors Connect the Ethernet ports Connect the RS 232 Connect the HDMI outputs Connect the audio output AO aa oie External IR Transmitter RS 232 DVD 1 jj Laptop d ra External IR ensor Ail Projector S PDIF S LCD Display LCD Display Digital Audio with Speakers with Speakers Player Recorder Step 2 Connect the power KRAMER SIMPLE CREATIVE TECHNOLOGY Overview 3 Overview The TP 582T and TP 582R are a high quality twisted pair transmitter and receiver for HDMI 100BaseT Ethernet bidirectional RS 232 and IR signals With the TP 582T you ca
10. al type Digital Color bit depth Undefined Display type RGB color Screen size 520 x 320 mm 24 0 in Power management Standby Suspend Active off sleep Extension blocs 1 CEA EXT DDC Cle sintes Not supported Color characteristics Default color space Non sRGB Display gamma 2 20 Red chromaticity Rx 0 674 Ry 0 319 Green chromaticity Gx 0 188 Gy 0 706 Blue chromaticity Bx 0 148 By 0 064 White point default Wx 0 313 Wy 0 329 Additional descriptors None Timing characteristics Horizontal scan range 30 83kKHz Vertical scan range 56 76Hz Video bandwidth 170MHz CVT standard Not supported GTF standard Not supported Additional descriptors None Preferred timing Yes Native preferred timing 1280x720p at 60Hz 16 10 Modeline 1280x720 74 250 1280 1390 1430 1650 720 725 730 750 hsync vsync Standard timings supported 720 x 400p at 70Hz IBM VGA 640 x 480p at 60Hz IBM VGA 640 x 480p at 75Hz VESA 800 x 600p at 60Hz VESA 800 x 600p at 75Hz VESA 1024 x 768p at 60Hz VESA 1024 x 768p at 75Hz VESA 1280 x 1024p at 75Hz VESA 1280 x 1024p at 60Hz VESA STD 1600 x 1200p at 60Hz VESA STD 1152 x 864p at 75Hz VESA STD EIA CEA 861 Information Revision number 3 IT underscan Supported Basic audio Supported YCbCr 4 4 Supported YCbCr 4 2 2 Supported Nat
11. e opening servicing Caution oo 2 ra Institute of Quality amp Control P N 2900 000582 Rev 5 Kramer Electronics Ltd Web site www kramerelectronics com E mail info kramerel com P N 2900 000582 REV 5
12. easonable use or maintenance misuse abuse accident neglect exposure to excess moisture fire improper packing and shipping such claims must be presented to the carrier lightning power surges or other acts of nature This limited warranty does not cover any damage deterioration or malfunction resulting from the installation or removal of this product from any installation any unauthorized tampering with this product any repairs attempted by anyone unauthorized by Kramer Electronics to make such repairs or any other cause which does not relate directly to a defect in materials and or workmanship of this product This limited warranty does not cover cartons equipment enclosures cables or accessories used in conjunction with this product Without limiting any other exclusion herein Kramer Electronics does not warrant that the product covered hereby including without limitation the technology and or integrated circuit s included in the product will not become obsolete or that such items are or will remain compatible with any other product or technology with which the product may be used How Long Does this Coverage Last Seven years as of this printing please check our Web site for the most current and accurate warranty information Whois Covered Only the original purchaser of this product is covered under this limited warranty This limited warranty is not transferable to subsequent purchasers or owners of this product What K
13. ector Connects to an RS 232 port 8 5VDC 5V DC connector for powering the unit 9 REMOTE IR Sensor Senses commands from the Kramer IR remote control device 10 JRLED Lights when an infrared signal is detected 11 INPUT SELECT Switch Press to toggle between HDMI inputs 12 IN 1 LED Lights when the HDMI 1 input device is connected 13 IN2LED Lights when the HDMI 2 input device is connected 14 OUT LED Lights when an HDMI output device is detected 15 LINKLED Lights when the TP connection is active 16 ONLED Lights when receiving power 1 Note that the IR sensor is only used to select the TP 582T inputs These IR signals cannot be transmitted to the TP 582R Your HDMI Line Transmitters Receiver 4 3 Your TP 582R HDMI Line Receiver DA Figure 3 and Table 3 define the TP 582R LINE IN HDMI Out 1 HDMI Line Receiver DA HDMI Out 2 S PDIF TOSLINK ETHERNET i Ourd Qur2 Link ON ooo0oo0oo TP 582R Figure 3 TP 582R HDMI Line Receiver DA Table 3 TP 582R HDMI Switcher Line Receiver Features Feature Function 1 LINE IN RJ 45 Connector Connects to the CAT 5 OUT RJ 45 connector on the TP 581T or TP 582T 2 HDMI OUT 1 Connector Connects to the HDMI acceptor 1 3 HDMI OUT 2 Connector Connects to the HDMI acceptor 2 4 S PDIF Connector Connects to a digital audio acceptor 5 TOSLINK Connector Connects to an optical audio acceptor 6 ETHERNET Connector
14. ht Rear center No Front left right center No Rear left right center No Rear EFE oinei No Report information Date generated Software revision 0 Data source Real time 0x0031 Operating system 5 1 2600 2 Service Pack 3 2 60 0 964 Raw data 00 FF FF FF FF FF FF 00 2E 4D 20 58 01 01 01 01 0A 13 01 03 80 34 20 78 EA B3 25 AC 51 30 B4 26 10 50 54 A5 4B 00 81 80 A9 40 71 4F 01 01 01 01 01 01 01 01 01 01 01 1D 00 72 51 D0 1E 20 6E 28 55 00 07 44 21 00 00 1E 00 00 00 FF 00 35 30 35 2D 37 30 37 34 35 35 30 31 30 00 00 00 FC 00 54 50 2D 35 38 32 20 20 20 20 20 20 0A 00 00 00 FD 00 38 4C 1E 53 11 00 0A 20 20 20 20 20 20 01 86 02 03 1B F1 48 10 05 84 03 02 07 16 01 23 09 07 07 65 03 0C 00 10 00 83 01 00 00 02 3A 80 18 71 38 2D 40 58 2C 45 00 07 44 21 00 00 1E 01 1D 80 18 71 1C 16 20 58 2C 25 00 07 44 21 00 00 9E 01 1D 00 72 51 D0 1E 20 6E 28 55 00 07 44 21 00 00 1E 8C 0A D0 8A 20 E0 2D 10 10 3E 96 00 07 44 21 00 00 18 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 47 19 LIMITED WARRANTY The warranty obligations of Kramer Electronics for this product are limited to the terms set forth below Whatis Covered This limited warranty covers defects in materials and workmanship in this product What is Not Covered This limited warranty does not cover any damage deterioration or malfunction resulting from any alteration modification improper or unr
15. ini Jack Connector Connects to an external infrared transmitter sensor receiver ETHERNET Connector Connects to a network RS 232 9 pin D sub Connector Connects to an RS 232 port 5V DC 5V DC connector for powering the unit gt olo NI OD a A WIN IN LED Lights when an HDMI input device is connected OUT LED Lights when an HDMI output device is detected LINK LED Lights when the TP connection is active 0 ONLED Lights when receiving power KRAMER SIMPLE CREATIVE TECHNOLOGY Your HDMI Line Transmitters Receiver 4 2 Your TP 582T HDMI Switcher Line Transmitter Figure 2 and Table 2 define the TP 582T Line Our HDMI IN 4 HDMI In 2 Rewore m IR INPUT SELECT O o o HDMI Switcher Line Transmitter fai Ind In2 Our Link On ooo0oo0o0 TP 582T Figure 2 TP 582T HDMI Switcher Line Transmitter Table 2 TP 582T HDMI Switcher Line Transmitter Features Feature Function 1 LINE OUT RJ 45 Connector Connects to the CAT 5 IN RJ 45 connector on the TP 582R 2 HDMIIN 7 Connector Connects to the HDMI source 1 3 HDMIIN 2Connector Connects to the HDMI source 2 4 R3 5mm Mini Jack Connector Connects to an external infrared transmitter sensor receiver 5 ETHERNET Connector Connects to a network 6 REMOTE CONTROL Terminal Block Connects to contact closure switches see Section 5 4 7 RS 232 9 pin D sub Conn
16. ion 3 2 e LED status indicators for input output link and power e Two RJ 45 CAT 5 output connectors one for the line output and the other for the Ethernet input 1 Since the TP 581T has only one input it does not have the input selection control which the TP 582T has that is contact closure IR and front panel input selection 3 Overview 3 2 3 3 The compact MegaTOOLS enclosures for the transmitters and the receiver let you rack mount up to two units side by side in a 1U 19 rack space when using the optional RK T2B rack In addition to the common features The TP 582T HDMI Switcher Line Transmitter also features e Two HDMI inputs e Momentary remote contact closure for input switching e Front panel input select button e IR remote control input switching via the Kramer IR remote control transmitter e Front panel input selection The TP 582R HDMI Line Receiver DA also features e One RJ 45 CAT 5 input connector e Two HDMI outputs e AnS PDIF digital audio output e A TOSLINK optical audio output The TP 581T HDMI Line Transmitter also features e One HDMI input About HDBaseT Technology HDBaseT is an advanced all in one connectivity technology Supported by the HDBaseT Alliance It is particularly suitable in the consumer home environment as a digital home networking alternative where it enables you to replace numerous cables and connectors by a single LAN cable used to transmit u
17. ive formats 1 Detailed timing 1 Modeline Detailed timing 2 Modeline 1920x1080p at 60Hz 16 10 1920x1080 148 500 1920 2008 2052 2200 1080 1084 1089 1125 hsync vsync 1920x1080i at 60Hz 16 10 1920x1080 74 250 1920 2008 2052 2200 1080 1084 1094 1124 interlace hsync vsync Detailed timing 1280x720p at 60Hz 16 10 Modeline N 1280x720 74 250 1280 1390 1430 1650 720 725 730 750 hsync vsync Detailed timing 4 720x480p at 60Hz 16 10 Modeline 720x480 27 000 720 736 798 858 480 489 495 525 hsync vsynce CE video identifiers VICs timing formats supported 18 KRAMER SIMPLE CREATIVE TECHNOLOGY Default EDID 1920 x 1080p at 60Hz HDTV 16 9 1 1 1920 x 1080i at 60Hz HDTV 16 9 1 1 1280 x 720p at 60Hz HDTV 16 9 1 1 Native 720 x 480p at 60Hz EDTV 16 9 32 27 720 x 480p at 60Hz EDTV 4 3 8 9 720 x 480i at 60Hz Doublescan 16 9 32 27 720 x 576i at 50Hz Doublescan 16 9 64 45 640 x 480p at 60Hz Default 4 3 1 1 NB NTSC refresh rate Hz 1000 1001 CE audio data formats supported LPCM 2 channel 16 20 24 bit depths at 32 44 48 kHz CE vendor specific data VSDB IEEE registration number 0x000C03 CEC physical address 1 0 0 0 Maximum TMDS clock 165MHz CE speaker allocation data Channel configuration 2 0 Front left right Yes Front LFE Front center Rear left rig
18. le 2 TP 582T HDMI Switcher Line Transmitter Features Table 3 TP 582R HDMI Switcher Line Receiver Features Table 4 Technical Specifications of the TP 581T TP 582T and TP 582R COINDAUUUA RWWNE m 11 12 13 14 15 ONA Introduction Introduction Welcome to Kramer Electronics Since 1981 Kramer Electronics has been providing a world of unique creative and affordable solutions to the vast range of problems that confront the video audio presentation and broadcasting professional on a daily basis In recent years we have redesigned and upgraded most of our line making the best even better Our 1 000 plus different models now appear in 11 groups that are clearly defined by function Congratulations on purchasing your Kramer MegaTOOLS TP 581T HDMI Line Transmitter TP 582T HDMI Switcher Line Transmitter or TP 582R HDMI Line Receiver DA that are ideal for e Home theater presentation and multimedia applications e Rental and staging The package includes the following e TP 581T and or TP 582T and or TP 582R e Power supply 5V DC e IR remote control transmitter for TP 582T only e This user manual Getting Started We recommend that you e Unpack the equipment carefully and save the original box and packaging materials for possible future shipment e Review the contents of this user manual to check for up to date user manuals application programs and to check if firmware upgrades are av
19. n IR emitter 6 Connect the REMOTE CONTROL terminal block to an external set of switches not shown in Figure 4 7 Connect the LINE OUT RJ 45 connector over CAT 5 twisted pair to the TP 582R LINE IN connector 8 Connect the 5V DC power adapter to the power socket and connect the adapter to the mains electricity not shown in Figure 4 1 On the TP 581T connect the HDMI IN connector to the HDMI source 2 There is no HDMI IN 2 connector for the TP 581T 9 Connecting the TP 581T TP 582T and TP 582R 5 2 Connecting the TP 582R To connect the TP 582R as shown in the example in Figure 4 do the following 1 Connect the HDMI OUT 1 connector to the first HDMI acceptor for example LCD display 1 Connect the HDMI OUT 2 connector to the first HDMI acceptor for example LCD display 2 Connect the ETHERNET RJ 45 connector to a network Connect the RS 232 9 pin D sub connector to an RS 232 port for example a projector Connect the IR 3 5mm mini jack to an IR sensor Connect S PDIF RCA connector to a digital audio acceptor for example a digital audio recorder Connect TOSLINK connector to an optical audio acceptor for example a digital audio recorder not shown in Figure 4 Connect the LINE IN RJ 45 connector over CAT 5 twisted pair to the TP 581T or TP 582T LINE OUT connector If required acquire the EDID see Section 5 6 Connect the 5V DC power adapter to the power socket and connect the
20. n select one of two HDMI inputs and convert it with the 100BaseT Ethernet RS 232 and IR input signals to a twisted pair signal The TP 582R converts the twisted pair signal back to 100BaseT Ethernet RS 232 IR and two HDMI outputs and de embeds the audio to S PDIF and TOSLINK audio outputs The TP 581T is identical to the TP 582T but has only one HDMI input For optimum range and performance using HDBaseT use Kramer s BC HDKat6a cable Note that the transmission range depends on the signal resolution source and display used The distance using non Kramer CAT 6 cable may not reach these ranges 3 1 Features of the TP 581T TP 582T and TP 582R This transmitter receiver pair features e Signals of up to 6 75Gbps up to 1080p 60Hz 36 bit over a range of up to 130m 430ft when using BC HDKat6a cables e HDTV compatibility e HDMI support V 1 4 with Deep Color x v Color Lip Sync HDMI Uncompressed Audio Channels Dolby TrueHD DTS HD CEC e 3D pass through e HDCP compliance e EDID PassThru passes EDID HDCP signals from source to display e A bidirectional RS 232 interface over which commands and data can flow in both directions via the RS 232 interface at rates up to 115200 allowing status requests and control of the destination unit e Bidirectional infrared interface for remote control of peripheral devices see Section 5 3 e 100BaseT Ethernet interface for connection to a network see Sect
21. ncompressed full high definition video audio 100BaseT Ethernet power over cable as well as various control signals The products described in this user manual are HDBaseT certified Using Twisted Pair Cable Kramer engineers have developed special twisted pair cables to best match our digital twisted pair products the Kramer BC HDKat 6a CAT 6 23 AWG cable significantly outperforms regular CAT 5 CAT 6 cables We strongly recommend that you use shielded twisted pair cable KRAMER SIMPLE CREATIVE TECHNOLOGY Overview 3 4 3 5 3 6 Recommendations for Achieving the Best Performance To achieve the best performance e Use only good quality connection cables we recommend Kramer high performance high resolution cables to avoid interference deterioration in signal quality due to poor matching and elevated noise levels often associated with low quality cables e Do not secure the cables in tight bundles or roll the slack into tight coils e Avoid interference from neighboring electrical appliances that may adversely influence signal quality e Position your TP 581T TP 582T TP 582R away from moisture excessive sunlight and dust This equipment is to be used only inside a building It may only be connected to other equipment that is installed inside a building Safety Instructions Caution There are no operator serviceable parts inside the unit Warning Use only the Kramer Electronics input power wall adap
22. ramer Electronics will do Kramer Electronics will at its sole option provide one of the following three remedies to whatever extent it shall deem necessary to satisfy a proper claim under this limited warranty 1 Elect to repair or facilitate the repair of any defective parts within a reasonable period of time free of any charge for the necessary parts and labor to complete the repair and restore this product to its proper operating condition Kramer Electronics will also pay the shipping costs necessary to return this product once the repair is complete 2 Replace this product with a direct replacement or with a similar product deemed by Kramer Electronics to perform substantially the same function as the original product 3 Issue a refund of the original purchase price less depreciation to be determined based on the age of the product at the time remedy is sought under this limited warranty What Kramer Electronics will not do Under This Limited Warranty If this product is returned to Kramer Electronics or the authorized dealer from which it was purchased or any other party authorized to repair Kramer Electronics products this product must be insured during shipment with the insurance and shipping charges prepaid by you If this product is returned uninsured you assume all risks of loss or damage during shipment Kramer Electronics will not be responsible for any costs related to the removal or re installation of this product from or into an
23. ter that is provided with the unit Warning Disconnect the power and unplug the unit from the wall before installing Recycling Kramer Products The Waste Electrical and Electronic Equipment WEEE Directive 2002 96 EC aims to reduce the amount of WEEE sent for disposal to landfill or incineration by requiring it to be collected and recycled To comply with the WEEE Directive Kramer Electronics has made arrangements with the European Advanced Recycling Network EARN and will cover any costs of treatment recycling and recovery of waste Kramer Electronics branded equipment on arrival at the EARN facility For details of Kramer s recycling arrangements in your particular country go to our recycling pages at http www kramerelectronics com support recycling Your HDMI Line Transmitters Receiver Your HDMI Line Transmitters Receiver This section describes the e TP 581T HDMI Line Transmitter see Section 4 1 e TP 582T HDMI Switcher Line Transmitter see Section 4 2 e TP 582R HDMI Line Receiver DA see Section 4 3 Your TP 581T HDMI Line Transmitter Figure 1 and Table 1 define the TP 581T HDMI Line Transmitter ETHERNET IN Our Link ON oo oo TP 581T Figure 1 TP 581T HDMI Line Transmitter Table 1 TP 581T HDMI Line Transmitter Features Feature Function LINE OUT RJ 45 Connector Connects to the CAT 5 IN RJ 45 connector on the TP 582R HDMI IN Connector Connects to the HDMI source IR 3 5mm M
24. y installation Kramer Electronics will not be responsible for any costs related to any setting up this product any adjustment of user controls or any programming required for a specific installation of this product How to Obtain a Remedy under this Limited Warranty To obtain a remedy under this limited warranty you must contact either the authorized Kramer Electronics reseller from whom you purchased this product or the Kramer Electronics office nearest you For a list of authorized Kramer Electronics resellers and or Kramer Electronics authorized service providers please visit our web site at www kramerelectronics com or contact the Kramer Electronics office nearest you In order to pursue any remedy under this limited warranty you must possess an original dated receipt as proof of purchase from an authorized Kramer Electronics reseller If this product is returned under this limited warranty a return authorization number obtained from Kramer Electronics will be required You may also be directed to an authorized reseller or a person authorized by Kramer Electronics to repair the product If itis decided that this product should be returned directly to Kramer Electronics this product should be properly packed preferably in the original carton for shipping Cartons not bearing a return authorization number will be refused Limitation on Liability THE MAXIMUM LIABILITY OF KRAMER ELECTRONICS UNDER THIS LIMITED WARRANTY SHALL NOT EXCEED THE
Download Pdf Manuals
Related Search