Premier Mounts EST100 project mount
Contents
1. M5 x 12mm M6 x 12mm Security Ya 20 x 5 16 Security M5 Security Wrench Barrel Cap Security Screw Qty 4 Screw Qty 4 Screw Qty 1 Qty 1 Qty 4 M5 x 10mm M5 Flat Washer Security Screw Qty 2 Qty 4 14 x 2 Wood Screw Sleeve Bushing Dual Stud Back Plate Qty 2 Nylon Qty 4 Qty 1 Installation Instructions Visit the Premier Mounts website at http www mounts com Page 3 D 24 EST100 EST200 Do NOT over tighten lag bolts when attaching the mount to the wall Improper installation may result in personal injury or damage to property THE EXACT CENTER OF THE STUD MUST BE LOCATED FOR CORRECT AND SAFE INSTALLATION Are you installing the single stud EST100 or the dual stud EST200 If EST100 continue to the EST100 Installation section below If EST200 go to the EST200 Installation section on page 8 EST100 Installation Marking Once the mounting points have been marked use a drill bit and portable drill to drill the pilot holes I lt Marking X After the pilot holes have been drilled use 14 x 2 Wood Screw two 2 14 x 2 wood screws to mount the projector arm to the wooden stud Projector Arm Wood Stud Use two 2 M5 x 10mm security screws to attach the projector arm cover plate to the projector arm Go to the Throw Distance Calculation section on page 10 Wood stud not shown Page 4 Visit the Premier Mounts website at http www mounts com Installa2. Page 14 Visit the Premier Mounts website at http www mounts com Installation Instructions EST100 EST200 Mount Adjustment After the projector has been installed the projector must then be adjusted To adjust the projector 1 Loosen the M5 set screw using the M5 Allen wrench both sides 2 Adjust the projector to the correct position Firmly grasp the projector in both hands and tilt either forward or backward to adjust the level OR Firmly grasp the projector in both hands and rotate side to side for orientation adjustment O Tighten both M5 set screws using the M5 Allen wrench Technical Specifications All measurements are in inches mm EST 100 SHORT THROW SINGLE STUD 17 5 0 445 16 00 40 6 EST 200 SHORT THROW DOUBLE STUD Installation Instructions Visit the Premier Mounts website at http www mounts com M5 Set Screw 6 18 F 20 i57 51 f Page 15 yy 24 EST100 EST200 PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Lifetime Warranty Premier Mounts warrants all mounting products to be free from defects in material and workmanship for the lifetime of the original installation of the product What Premier Mounts Will Do At the sole option of Premier Mounts Premier Mounts will repair or replace any product or product part that is defective If Premier Mounts chooses to replace a defective product or part a replacement prod uct or part
3. fy Raise or lower each of the mounting legs by rotating the leveling barrels until all of the mounting legs are at an equal height Lower the mounting leg by rotating the leveling barrel counter clockwise Raise the mounting legs by rotating the leveling barrel clockwise When the desired position is achieved tighten the mounting screws to the projector and then tighten the hex head leg screws with the M5 Allen wrench Page 10 Visit the Premier Mounts website at http www mounts com Installation Instructions EST100 EST200 Mounting Hardware Too Long The depth of some projector mount points may prevent you from tightening the M2 5 and M3 mounting hardware You can reduce the length of the M2 5 and M3 mounting hardware by stacking up to a maximum of five 5 M3 flat washers inside the Mounting Hardware leveling barrel Avoid stacking too many M3 washers the mounting hardware must M3 Washer thread into the projector mount point at least four 4 complete turns Leveling Barrel Cutaway View 1 Identify the projector s approximate front to back center of gravity Place your hands on each side of the projector and gently lift it an inch from the surface on which it is resting Carefully adjust your grip on the projector until Side to Side it seems balanced from front to back M
4. will be shipped to you at no charge but you must pay any related labor costs What is Not Covered Limitations Premier Mounts disclaims any liability for damage to mounts adapters displays projectors other property or personal injury resulting in whole or in part from improper installation modification use or misuse of its products NOTWITHSTANDING ANYTHING TO THE CONTRARY IN THIS WARRANTY THIS WARRANTY IS LIMITED TO FIVE YEARS FROM THE DATE OF PURCHASE IN THE EVENT THAT THE WARRANT ED PRODUCT IS COMMERCIALLY RENTED OUT Electrical products and components such as amplifiers speakers motors switches remote controls and related electrical items are backed by a 3 year warranty Premier Mounts disclaims all other warranties express or implied including warranties of merchant ability and fitness for a particular purpose Premier Mounts is not responsible for incidental or conse quential damages including but not limited to inability to use its products or labor costs for removing and replacing defective products or parts Some states do not allow the exclusion or limitation of inci dental or consequential damages so the above limitation or exclusion may not apply to you What Customers Must Do for Warranty Service If you discover a problem that you think may be covered by the warranty you must report it in writ ing to the address below within thirty 30 days Proof of purchase an original sales receipt from the original
5. 4 PREMIER 24 PA MOUNTS THE ORIGINAL MOUNT COMPANY INSTALLATION INSTRUCTIONS Single Stud Dual Stud Short Throw Projector Wall Mount Model EST100 EST200 NORTH AMERICA 1321 S State College Blvd Fullerton CA 92831 USA USA and Canada Phone 1 800 368 9700 Fax 1 800 832 4888 Other Locations Phone 001 714 632 7100 Fax 001 714 632 1044 9530 011 001 0X Rev 1 24 EST100 EST200 oa Table of Contents Weight Capacity sist it iccctnrnecdndanouaneanndnns a2 Warning Statements DS oe 2 Installation Tools PPANS 3 Parts List AEE E T pd Features seronenreirieii ae A Determining the Installation Height se O Wood Stud Installation esti E en tee EA EE E EA EON Ereni Throw Distance Calculation NE A e a esi ee f e eee 10 Projector Installation paris ae eens ea a eee cane en aaa 10 Attaching the Mount Carriage ee ee oa E E E Il Multiple Mounting Point Installation ETOT eee os VERET cel ee Single Mounting Point Installation 7 i E AE E EE E T Attaching the Mount Carriage to the ai AE EE E TO ene EE ID Cable Routing Optional PEE E EEEE E A Securing the Projector Optional a ne E tea neta Mount Adjustment 20 se a N EE OE Technical Specifications eee oe E E E E E E bl Warranty IO tirkat PE E E EE I D E R E E E dtadianelod 18 Disclaimer a DENSE _ A E e E E E EE Weight Capacity THE WALL STRUCTURE MUST BE CAPABLE OF HOLDING FIVE Maximum projector weight 25 Ibs 5 T
6. IMES THE WEIGHT OF THE PROJECTOR IF NOT THEN THE WALL STRUCTURE MUST BE REINFORCED Warning Statements aa PRIOR TO THE INSTALLATION OF THIS PRODUCT THE INSTALLATION INSTRUCTIONS SHOULD BE READ AND COMPLETELY UN DERSTOOD THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND PROPERTY DAMAGE KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE STOP PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS AND IS NOT RESPONSIBLE FOR ANY DAMAGES CLAIMS DEMANDS SUITS ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM ARISING OUT OF OR IN ANY MANNER RELATING TO ANY SUCH USE ATTACHMENTS OR MODIFICATIONS STOP SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT USE PROPER TT AT PPS OVE SAFETY GEAR AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY At least two qualified people should perform the assembly procedure Injury and or damage can result from dropping or mishandling the projector If mounting to studs make sure that the mounting screws are anchored into the center of the studs Use of an edge to edge stud finder is recommended Be aware of the mounting environment If drilling and or cutting into the mounting surface always make sure that there ar
7. consumer purchaser must accompany all warranty claims Warranty claims must also include a description of the problem the purchaser s name address and telephone number General inquiries can be addressed to Premier Mounts Customer Service at 1 800 368 9700 Warranty claims will not be accepted over the phone or by fax Premier Mounts Attn Warranty Claim 1321 S State College Blvd Fullerton CA 92831 USA How State Law Applies This warranty gives you specific legal rights and you may also have other rights which vary from state to state Premier Mounts intends to make this manual accurate and complete However Premier Mounts makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Premier Mounts makes no representation of warranty expressed or implied regarding the information contained herein Premier Mounts assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Page 16 Visit the Premier Mounts website at http Awww mounts com Installation Instructions
8. e no electrical wires in wall Cutting drilling into an electrical line may cause serious injury Make sure there are no water lines inside the wall where the mount is to be located Cutting drilling into a water line may cause severe water damage to the mounting surface This product is intended for indoor use only Use of this product outdoors could lead to product failure and personal injury Do not install near sources of high heat Do not install on a structure that is prone to vibration movement or chance of impact Contact Premier Mounts with any questions 800 368 9700 techsupport mounts com Page 2 Visit the Premier Mounts website at http www mounts com Installation Instructions 4 EST100 EST200 24 Installation Tools The following tools may be required depending upon your particular installation They are not included Phillips Screwdriver Drill Bit Electronic Stud Finder Parts List Make sure your Premier Mounts product has the following hardware and components before beginning installation If there are parts missing and or damaged stop the installation and call Premier Mounts at 800 368 9700 EST100 EST200 Hardware Projector Arm Projector Arm Mount Carriage Qty 1 Cover Plate Qty 1 S Qty 1 d M3 Flat Washer M2 5 x 8mm M2 5 x 10mm M3 x 16mm M4 x 12mm M5 x 10mm Qty 4 Security Screw Qty 4 Security Screw Qty 4 Security Screw Qty 4 Security Screw Qty 4 Security Screw Qty 3 a
9. entally note the apparent center of i Center of Gravity gravity Identify the projector s approximate side to side center of gravity Place your hands on the front and back of the projector and gently lift it an inch from the surface on which it is resting Carefully adjust your grip on the projector until it seems balanced from side to side Mentally note the apparent center of gravity Make sure the mount carriage is as close as possible to the projector s center of gravity Front to Back Center of Gravity 1 Position the legs accordingly for best configuration You may raise or lower each leg independently by turning the leveling barrels Sliding M6 Secure the legs to the mount carriage by screwing Square Nut M6 x 12mm security screws into the M6 square nut do not overtighten on the mounting legs Verify the position of the integrated sliding M6 square nut in the mounting leg relative to a nearby slot on the mount carriage If the M6 square nut is not aligned with any slot you can use any thin implement such as a toothpick to nudge it into alignment Installation Instructions Visit the Premier Mounts website at http www mounts com Page 11 yy 24 EST100 EST200 1 Tighten the mounting screws which secures the mounting legs to the projector Do not overtighten the mounting screws 1 Insert one 1 Barrel Cap except for the security barrel into the end of each leve
10. ling barrel Go to the Attaching the Mount Carriage to the Projector Arm section on page 15 Single Mounting Point Installation A single 1 4 20 x 5 16 screw must be used to attach the mount carriage to the projector if your projector has only one mounting point A Do not overtighten the 20 x 5 16 screw Proceed to the Attaching the Mount Carriage to the Projector Arm section on page 15 Page 12 Visit the Premier Mounts website at http www mounts com Installation Instructions A EST100 EST200 24 Attaching the Mount Carriage to the Projector Arm Insert and slide the mount carriage along the projector arm to the desired position Projector not shown Once you have the desired position use one 1 M5 x 10mm security screw to tighten the mount carriage in place M5 x 10mm Security Screw Proceed to the Cable Routing Optional section on page 16 Installation Instructions Visit the Premier Mounts website at http www mounts com Page 13 24 EST100 EST200 Cable Routing Optional 1 Remove the plastic cover s from the cable routing openings 2 Route cables and wiring through the openings then out the back or bottom near the wall Proceed to the Securing the Projector Optional section Plastic Cover Route cables and wiring through the projector arm openings then out the back or bottom near the wall Securing the Projector Optional Padlock Combination or Keyed
11. s or a single mounting point If your projector has multiple mounting points proceed to the Multiple Mounting Point Installation section PA A knn AL A If your projector has a single mounting point skip to the Single wel Mounting Point Installation Small Straw Depth Plus 1 8 Allowance Small Straw Depth Plus 1 8 Allowance or Toothpick M or Toothpick Installation Instructions Visit the Premier Mounts website at http www mounts com Page 7 D C4 EST100 EST200 1 Locate the projector s mounting points 2 Position the mounting legs on the projector The mounting legs are pre installed Depending on the requirements of your projector you may remove one of the mounting legs fy The number and placement of mounting points on projectors varies between projector manufacturers Refer to you projector s technical specifications for the number and location of the mounting points on your specific projector Mount carriage not shown 1 Attach the mounting legs to the projector using the corresponding mounting hardware A Do not tighten the mounting hardware at this time Screws shown for illustration purposes only 1 If the mounting legs need to be leveled rotate the leveling barrels to level the mounting bracket 2 To raise the mounting legs rotate the leveling barrel clock wise To lower the mounting leg rotate the leveling barrel counter clock wise
12. the back plate to the wooden studs where the pilot holes are The elongated mounting slots in the back plate allow some lateral shift for Na precise adjustments against the studs hy Proceed to the Throw Distance Calculation section on page 10 Page 6 Visit the Premier Mounts website at http www mounts com Installation Instructions Al EST100 EST200 A Attaching the Mount Carriage Selecting the Mounting Hardware Insert a small straw or toothpick into the threaded inserts found on the bottom or top of the projector Use a pencil to mark the depth of the threaded insert on the small straw or toothpick Mark the straw or toothpick 1 8 above the depth of the threaded insert as shown in Figure 1 Insert the small straw or toothpick into the remaining threaded inserts to compare and verify their depth using the straw or toothpick s 1 8 allowance mark Locate the correct diameter screw for the threaded insert If the screw you selected is longer than the 1 8 allowance mark on the small straw or toothpick as shown in Figure 2 and Figure 3 do not use this screw The Marking the 1 8 screw length must not bypass the mark Allowance r gt Marking the Depth Test each size of the screws provided The correct screws should thread easily into the mounting point and not pull out when tension is applied Threaded Insert r A r Small Straw or Toothpick Does your projector have multiple mounting point
13. tion Instructions 4 EST100 EST200 24 EST200 Installation lt Wood Stud Stud finder Use an electronic stud finder not supplied to locate the center of the stud that is in the wall A Use a pencil to mark the first mounting point just Mounting Point above your height mark from page 5 Je Mark I de Height Mark from page 5 1 Use the level to make sure the back plate is level from side to side 2 Align one of the lower mounting slots of the back plate with the first mounting point mark and use a pencil to mark the rest of the mounting points fin Four 4 mounting points must be used Two 2 upper mounting points and two 2 lower mounting points Once the mounting points have been marked use a drill bit and portable drill to drill the pilot holes Marking Installation Instructions Visit the Premier Mounts website at http www mounts com Page 5 24 EST100 EST200 Projector Arm Put the projector arm cover plate on the projector arm N Cover Plate Projector Arm 1 Place the projector arm assembly within the desired mounting slots on the back plate 2 Use four 4 M5 x 10mm security screws four 4 M5 flat washers and four 4 sleeve bushing nylons to attach the projector arm assembly to the back plate The elongated mounting slots in the back plate allow some lateral shift for precisely adjusting the projector arm Na W Use four 4 14 x 2 wood screws to mount
Download Pdf Manuals
Related Search