Havis C-VS-0809-CHGR-1 car kit
Contents
1. threading screws 10mm under rubber mat as shown included in hardware kit to mount rear of console 7 16 wrench A Q ie x Push Console assembly forward and Place KRM98017 Rubber O Cut off O E M 12 volt socket tighten all floor mount bracket Ring onto AUX socket assembly connectors and attach 1 4 spade hardware Run all wiring as needed Push ring all the way on This connectors on O E M wires O E M allows for a tight fit when installed wire will need to be extended for rear socket If desired new heavier gauge wires can be installed instead of using O E M wiring Prior to installing passenger side Reconnect under dash AUX Attach passenger and driver side trim panel firmly push in the USB connectors back together trim panels on with 8 x 1 4 Flat O E M Auxiliary socket assembly Plug spade connectors onto 12 volt Head Screws 3 screws each panel into cutout AUX lettering goes sockets included with hardware kit toward the front of vehicle Positive Pink wire connects to Install 12 volt socket into 7 8 hole center silver spade and Negative Phillips Screwdriver or close off with supplied plug Black wire to outboard gold spade C VS 0809 CHGR 1_INST_4 11 a O E M Prior to installation of control heads and a A cover is provided to guard the Sensor on transmission hump If desired accessories determine desired position and attach to existing stud and 6mm nut and at2. Havis Inc 75 Jacksonville Road PO Box 2099 Warminster PA 18974 F T 800 524 9900 F 215 957 0729 Productivity in motion www havis com INSTALL INSTRUCTIONS C VS 0809 CHGR 1 2011 2013 Dodge Charger Police Package VEHICLE SPECIFIC CONSOLE With 17 inches Equipment space TOOLS NEEDED Phillips Screw Driver Wire Cutters Wire Crimping tool Socket set Standard amp Metric 7 16 wrench T 20 Torx Bit QTY DESCRIPTION PART 1 Main Console Housing CM004345 CM004345 Main Housing Includes 1 Floor Mount Bracket CM003956 1 Front Center End Panel CM004380 1 Lighter Socket with cap CM216560 3 7 8 Plug CM86430 l O Ring KRM98017 Not Included with CM00435 Housing but included with complete kit l Driver Side Trim Panel CM004381 l Passenger Side Trim Panel CM004382 1 Lighter Socket with cap CM216560 1 Sensor Cover CM001638 l Hardware kit C HK 174 C VS 0809 CHGR 1 Assembly T CM004382 N Passenger Side Trim Panel CM003956 Floor Mount Bracket CM004381 Driver Side Trim Panel CM004380 Front Center End Panel CM004345 Main Console Housing ALWAYS Read all Instructions before installing any Havis Inc products Use Hardware included with install kit NOTE f your vehicle has the optional carpet interior there will be a small hole in the carpet not covered by the console housing at the rear If desired an optional cover plate part number CM001642 is available C VS 0809 CHG
3. R 1_ INST 4 11 Cover plate not shown Remove bolts that hold underside O E M console prior to Remove forward O E M console of extrusion to rear floor bracket C VS 0809 CHGR 1 console plastic cover and remove two 2 7 16 wrench installation nuts from front floor bracket Remove rear floor bracket bolts Nuts to be reused 10mm and center console bolt 10mm Remove Ignition proximity sensor Remove sensor and 12 volt socket Remove O E M plastic center antenna from rear underside of wire harness assembly from under cono O E M console side of O E M console Phillips Screwdriver Pop out AUX socket from center SEE NOTE BELOW of O E M console Passenger side Plug O E M wire harness back Omer a ear Eaa tour Carefully place console assembly between seats and onto front O E M floor studs a proximity sensor antenna to onto original connectors ae transmission hump with Velcro NOTE 2012 and newer cars include an O E M bracket with this sensor already relocated Velcro mounting C VS 0809 CHGR 1_INST 4 11 will not be needed y ra F gt Lite mes BANTER i eA Sey SAMI f le Ry Pz rif de ify iY PEF Sy lt z a i e Bee a j ejg yy paes hy je iu a ee P f aT r CE fd fi a Loosely attach previously removed Loosely attach rear of console to Use OEM screws if provided or nuts onto front floor studs existing floor inserts Inserts located 1 4 x 3 4 self
4. tach Tilt Swivel and Docking Station washer provided bracket Console assembly complete Completed console installation with Laptop with Docking Station Docking Station example 1 Completed C VS 0809 CHGR 1 console installation with Laptop Docking Station example 2 C VS 0809 CHGR 1_INST_4 11
Download Pdf Manuals
Related Search