Rosewill RHMS-13002 flat panel desk mount
Contents
1. Monitor Arm System RHMS 13001 RHMS 13002 User Manual For apple LED Cinema Display 24 inch iMac aluminum and 27 inch iMac amp VESA 100 75 Mount Monitor Arm System RHMS 13001 13002 User Manual gt Rotate your iMac forward another 10 degrees until the 8 screws on top of the stand are visible and the stand is locked in place Keep your iMac upright until the stand is locked in place gt To prevent any scratches to your iMac display lay a soft towel or cloth on a flat surface Hold the sides of your iMac and carefully lay it down on a flat surface with the display facing down and the stand hanging over the edge of the work area 2 Apple LED Cinema Display Mount Installation w O TORX tool Hex tool 4mm gt Use the TORX tool to remove the 8 screws that attach the stand to the back of your iMac You ll need these screws to attach the flange to your iMac so set them aside gt Remove the stand and put it in a safe place in case you want to reattach it TORX tool gt Align the hole in the flange with the pin on the back of your iMac and then use the TORX tool and the 8 screws you removed from the stand to attach the flange Monitor Arm System RHMS 13001 13002 User Manual Supplied Parts and Hardwares M3 Hex Tool EVA Swivel Mon P Wrench 4mm _ Cushion Arm Mo P C LA lastic Flange arts RI Parts OA J A itor Cable Dual unt Clip2. Stand L LLA AAA el fos RHMS 13001 RHMS 13002 Specification 13001 VESA MIS D 75x75 100x100 VESA MIS D 75x75 100x100 200mm 200mm 0 0 360 360 360 360 360 360 105 105 400mm 400mm o 0 lt 14kg or 30 9lbs Wt Load Pole Max load lt 20kg or 44lbs 1 Apple LED Cinema Display Stand Removal gt Turn off your iMac and disconnect the power cord and all cables gt Turn your iMac so that the back is facing you and then rotate the top forward until it won t go any further gt Release the latch by inserting the access card in the space directly above the top of the stand gt The access card should go into the space at a slight upward angle for about 3 4 of an inch 19mm 20mm gt If it goes in farther you ve missed the latch so try again Access card Use only the access card provided with the kit for this step Use of any other object or instrument could result in personal injury and or damage to your iMac If you have misplaced or damaged the access card please contact Customer Support for assistance Monitor Arm System RHMS 13001 13002 User Manual gt Set up the 4 plastic parts to the mount gt Place the mount over the flange Keep the flange in the locked position while you attach the mount adapter gt Use the Hex tool 4mm to fasten the screw into the top of the mount gt After installation of the display mount
3. or loosen the swing motion 2 If the display does not stay in place or movement is stiff please use the wrench to increase or decrease the tension until the motion is right for you Increase Tension Turn Clockwise Decrease Tension Turn Counter Clockwise M3 Rosewill Technical Support information 1 800 575 9885 Monday Friday 8AM 5PM PST techsupport rosewill com
4. you may mount the LCD Cinema Display onto the LCD Arm For details on how to mount the Display to the LCD arm please reference the LCD Arm System manual The information has been extracted from the VESA Mount Adapter Install Guide Please refer to the following website for additional details http www rosewill com support Support _Download aspx Monitor Arm System RHMS 13001 13002 User Manual Monitor Arm System RHMS 13001 13002 User Manual 3 Transform to VESA Mount 5 Install Arms 100x100 or 75x75 mm gt Align the back of the display with either the VESA 100x100mm or 75x75mm pre drilled holes on the display mount gt Use the included screws to secure the VESA mount onto the display tighten or loosen the swing motion gt After completion of the VESA Mount installation mount the display to the LCD Arm Please reference the LCD Arm System manual lt Use the M3 wrench to J Adjust to your preferred height and then lock the position by turning the wrench Use the M3 wrench to tighten or loosen the swing motion A 4 Installation Method of Mount Type C Clamp EVA Cushion Table 20 60mm Insert the wrench into w the provided slot when not in use Monitor Arm System RHMS 13001 13002 User Manual Monitor Arm System RHMS 13001 13002 User Manual 6 Install Monitors 7 Route Cables 000000000 Use the M3 wrench to tighten
Download Pdf Manuals
Related Search