Chief RPMA204 project mount
Contents
1. 134 Gi Z HA E Figure 3 3 Align four mounting holes RPMX with four pilot holes IMPORTANT When RPMX is properly positioned the Set screw access hole should be pointing directly at target or 180 AWAY from target 4 Secure RPMX to structure using four 10 24 x 3 Grade 2 wood screws not included and four 1 4 Grade 2 flat washers not included See Figure 4 O Figure 4 5 Proceed to Installing Projector with Interface Bracket section Installing to Concrete Ceiling WARNING The is designed to be mounted to a concrete ceiling with a minimum thickness of 8 and a maximum drywall covering of 5 8 1 Using the RPMX as a guide mark four mounting hole locations on ceiling using a pencil or similar tool 2 Drill four 1 4 6 4mm dia pilot holes to a depth of 2 1 2 64mm deep See Figure 5 Pilot 6 4mm hole 1 4 dimensions 64mm 2 1 2 Figure 5 Installation Instructions RPMA RPMB RPMC Series 3 Align four mounting holes RPMX with four pilot holes IMPORTANT When RPMX is properly positioned the set screw access hole should be pointing directly at target or 180 AWAY from target WARNING Anchors not provided must be installed into structurally sound solid concrete Inst2. minimum thickness steel or aluminum ASTM B221 threaded extension column not included into threaded collar until tight with a minimum of four threads engaged 2 Thread RPMX projector mount A onto the threaded extension column not included until hand tight 3 Turn RPMX clockwise or counter clockwise until front of mount is facing target IMPORTANT When is properly positioned the set screw access hole should be pointing directly at target or 180 AWAY from target 4 Secure RPMX to pipe by turning set screw with a 5 32 hex key until tight See Figure 1 CAUTION DO NOT OVERTIGHTEN Over tightening of set screw can damage threads on pipe Threaded extension column not included Set screw access hole Figure 1 5 Turn security screw access from bottom of RPMX See Figure 2 using a Phillips screwdriver until set screw cannot be seen through set screw access hole in RPMX See Figure 1 Security screw RPMX bottom view Figure 2 6 Proceed to Installing Projector with Interface Bracket section RPMA RPMB RPNC Series Installation Instructions Installing to Wood Framework Joists 1 Using the RPMX as a guide mark four mounting hole locations See Figure 3 2 Drill four 3 32 2 4mm dia pilot holes to a depth of 1 3 4 45mm deep 2 4mm 77 N hole 2 3 32 dimensions 45mm
3. 11 Turn ROLL micro adjustment screw right or left using a 2 Phillips screwdriver until image is properly aligned on target Tighten ROLL adjustment locking screw using a 2 Phillips screwdriver Figure 11 RPMA RPMB RPNC Series Installation Instructions 10 Installation Instructions RPMA RPMB RPMC Series milestone AV Technologies Product identification Model type Category description Brand Manufacturer EU Representative Concerning A sample of the product has been tested by Test report reference NC707785 WC700711 WC603563 Applied standards Means of conformity MANUFACTURERS DECLARATION OF CONFORMITY For RPMA RPMB RPMC Mounting devices Stands and other Accessories to be used with entertainment electronics Chief Milestone AV Technologies 6436 City West Parkway Eden Prairie MN 55344 Milestone AV Technologies Fellennoord 130 5611 ZB Einhoven The Netherlands 31 0 20 5708923 EMC Ln o E We EN50022B EN55014 1 EN60065 A12 2011 EN61000 4 We declare under our sole responsibility that this product is in conformity with Directive 93 68 EEC Marking 98 37 EC Machinery 2001 95 EC Safety 89 336 EEC EMC and or complies to the essential requirements and all other relevant provisions of the based on test results using non harmonized standards in accordance with the Directives mentioned 11 RPMA RPMB RPNC Ser
4. mounts are designed to be e mounted to a 1 1 2 NPT or NPSM following ANSI ASME B1 20 1 Schedule 40 0 154 minimum thickness aluminum ASTM B221 threaded extension column e mounted to double 2 x 4 wood stud cross bracing 1 1 2 on center between two 2 x 4 ceiling joists with a maximum drywall covering of 5 8 e mounted to a concrete ceiling with a minimum thickness of 8 and a maximum drywall covering of 5 8 or suspended from four 10 24 grade ASTM A307 or better threaded rods not included which are secured to Unistrut amp angle or channel assembly overhead structural members trusses or l beams by 10 24 grade ASTM A307 or better jam nuts not included NOTE RPMA RPMB Series be used with Listed Chief models WM110S WM120S WM130S WM210S WM220S WM230S WM240S WM210Sl WM220SI WM230SI WM240SI and LSB101 not included SAVE THESE INSTRUCTIONS Installation Instructions RPMA RPMB RPMC Series DIMENSIONS 5 072 9 Lee f du RO LLADJUSTE ENT POUT 3 PI C HAD JUSTN ENT MT 410 SECURITY LOCK TOOLS REQUIRED FOR INSTALLATION g 5 32 security included hi 3 32 2 4mm dia wood 1 4 6 4mm dia concrete RPMA RPMB RPNC Series In
5. INSTALLATION INSTRUCTIONS RPA Elite Series Projector Mounts CHIEF RPMA RPMB RPMC Series Our Mounts Your Vision RPMA RPMB RPNC Series Installation Instructions NOTE RPMA RPMB and RPMC models are included in these installation instructions Throughout these instructions RPMX is used to designate all of the models covered by these instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved IMPORTANT SAFETY INSTRUCTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corres
6. allation into hollow concrete block mortar or concrete that exhibits cracking spalling or other defects may result in failure of anchor and serious personal injury or damage to equipment 4 Install four Toggler AF6 Alligator concrete anchors not included by inserting into pilot holes and hammering in until flush with mounting surface 5 Secure RPMX to structure using four 1 4 Grade 2 flat washers and four 10 24 x 3 Grade 2 wood screws not included See Figure 6 o D Figure 6 Installing to Threaded Rod NOTE The RPMX projector mount may be suspended from four 10 24 grade ASTM A307 or better threaded rods not included which are secured to unistrut angle or channel assembly overhead structural members trusses or l beams by 10 24 grade ASTM A307 better jam nuts not included 1 Secure one end of each of the four threaded rods not included to the structural member 2 Install four 10 24 jam nuts not included onto each threaded rod 3 Install RPMX onto threaded rods inserting the rods into the four holes on top of the RPMX NOTE Hole in the RPMX allows socket wrench access without unit disassembly 4 Secure the threaded rods to the RPMX with 10 24 jam nuts not included and 1 4 washers not includ
7. ed See Figure 7 Secure using jam nuts not included Threaded Secure with jam gt o nuts and 4 not included e 7 5 Proceed to Installing Projector with Interface Bracket section PROJECTOR INSTALLATION IMPORTANT Model RPMX uses optional Chief SLM Series interface brackets See Parts drawing 1 Attach projector to interface bracket B using installation instructions and hardware included with the interface bracket NOTE Security screws can be substituted when mounting Interface bracket to projector by using the hardware and installation instructions in the All Points Security Kit included with interface bracket Installing Projector with Interface Bracket 1 Orient projector with interface bracket 2 Lift projector so that screws with thumb nuts are aligned with mounting slots in mount base See Figure 8 3 Slide projector with mounting bracket into mounting slots in mount base until screws are seated against the back of mounting slots RPMA RPMB RPNC Series Installation Instructions WARNING IMPROPER INSTALLATION CAN LEAD TO PROJECTOR FALLING RESULTING IN SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Make certain mounting slots in mount base slide under thumb screws and that screws are seated in the back of slots Mounting structure not shown for clarity Figure 8 4 Verify mounting screws are proper
8. foque del proyector Ziel des Projektors Mira do projector Punto di proiezione Doel van de projector Cible du projecteur By Hand la main A mano Von Hand A mano Met de hand Com ej 0000 Security Wrench Cl de s curit Chiave di sicurezza Sicherheitsschl ssel Llave de seguridad Veiligheidssleutel Chave de Installation Instructions RPMA RPMB RPNC Series PREPARATION Locate Mounting Site WARNING IMPROPER INSTALLATION MAY LEAD TO PROJECTOR MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT It is the installers responsibility to make certain the structure to which the projector mount is being mounted is capable of supporting five times the weight of the projector mount and all attached equipment Reinforce the structure as required before installing the projector mount 1 Determine required position of the RPMX projector mount 2 Determine required distance of the projector mount from the screen using the projector specifications NOTE Proceed to Installing to 1 1 2 Threaded Extension Column Installing to Wood Framework Installing to Concrete Ceiling or Installing to Threaded Rod section as appropriate INSTALLATION Installing to 1 1 2 Threaded Extension Column 1 Install 1 1 2 NPT or NPSM following ANSI ASME 1 20 1 Schedule 40 0 154
9. ies Installation Instructions USA International G CHIEF Our Mounts Your Vision Europe Chief a products division of Milestone AV Technologies Asia Pacific 8800 002307 Rev01 2014 Milestone AV Technologies www chiefmfg com 05 14 gt 6436 City West Parkway Eden Prairie 55344 800 582 6480 952 225 6000 877 894 6918 952 894 6918 Franklinstraat 14 6003 DK Weert Netherlands 31 0 495 580 852 31 0 495 580 845 Office No 918 on 9 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477
10. ly seated in mounting slots in mount base 5 Move locking lever to LOCKED position See Figure 8 6 Insert key into lock and turn to secure projector to RPMX 7 Route all cables as required ADJUSTMENTS The RPMX projector mount can be adjusted for pitch vertical elevation roll horizontal tilt and yaw rotation WARNING OVER LOOSENING OR REMOVAL OF HARDWARE MAY RESULT IN PERSONAL INJURY OR SERIOUS DAMAGE TO EQUIPMENT RPMX projector mount and hardware is to be loosened only enough to allow for necessary movement YAW Adjustment Rotation 1 2 3 Loosen YAW adjustment locking screw using a 2 Phillips screwdriver See Figure 9 Turn YAW micro adjustment screw right or left using a 2 Phillips screwdriver until image is properly aligned on target Tighten YAW adjustment locking screw using a 2 Phillips screwdriver Figure 9 Pitch Adjustment Vertical Elevation 1 2 3 Loosen PITCH adjustment locking screw using a 2 Phillips screwdriver See Figure 10 Turn PITCH micro adjustment screw right or left using a 2 Phillips screwdriver until image is properly aligned on target Tighten PITCH adjustment locking screw using a 2 Phillips screwdriver Figure 10 Installation Instructions RPMA RPMB RPMC Series Roll Adjustment Horizontal Tilt 1 2 3 Loosen ROLL adjustment locking screw using a 2 Phillips screwdriver See Figure
11. ponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to the RPMX does not exceed 50 Ibs 22 7 kg The weight capacity of the RPMX may be LIMITED to the lowest weight capacity of any other components located between the RPMX and the supporting structure WARNING Use this mounting system only for its intended use as described in these instructions Do not use attachments not recommended by the manufacturer WARNING Never operate this mounting system if it is damaged Return the mounting system to a service center for examination and repair WARNING Do not use this product outdoors IMPORTANT The RPMX
12. stallation Instructions LEGEND Tighten Fastener Serrez les fixations Serrare il fissaggio Befestigungsteil festziehen Apretar elemento de fijaci n Bevestiging vastdraaien Apertar fixador Pencil Mark Marquage au crayon Segno a matita Stiftmarkierung Marcar con l piz Potloodmerkteken Marcar com l pis Loosen Fastener Desserrez les fixations Allentare il fissaggio Befestigungsteil l sen Aflojar elemento de fijaci n Bevestiging losdraaien Desapertar fixador Drill Hole Percez un trou Praticare un foro Bohrloch Perforar Gat boren Fazer furo Phillips Screwdriver Tournevis a pointe cruciforme Cacciavite a stella Kreuzschlitzschraubendreher Destornillador Phillips Kruiskopschroevendraaier Chave de fendas Phillips Adjust Ajuster Regolare Einstellen Ajustar Afstellen Ajustar Hex Head Wrench Cl a t te hexagonale Chiave esagonale Sechskantschl ssel Llave de cabeza hexagonal Zeskantsleutel Chave de cabeca sextavada Hammer Martillo Hammer Martelo Martello Hamer Marteau d y 9 E Open Ended Wrench Cl fourche Chiave a punte aperte Gabelschl ssel Llave de boca Steeksleutel Chave de bocas Target of Projector Punto de en
Download Pdf Manuals
Related Search