zBoost TRIO CONNECT
Contents
1. Why isn t my cell phone indicating more signal with more bars You may not always observe more bars on your signal meter because of the signal spreading out from the antenna If your phone has a dB meter 3 dB is a significant increase of 2x 6 dB is 4x and 10 dB is 10x On a four bar phone one bar equals about 10 dB The increase in signal you will see depends upon e The level of signal at the Signal Antenna outdoor The care of the antenna placement two feet away from metal adequate antenna separation 15 horizontal feet of separation is recommended e The signal already present inside related to building losses e The distance of your phone device from the Base Unit signal spreads or diminishes rapidly with distance There are usually several mobile devices in use at one time in my home will your product boost all of our signals simultaneously The zBoost TRIO Workspace is designed to cover multiple signals simultaneously and will allow multiple users to operate at the same time Does the zBoost work if you have no bars No if no signal is present outdoors zBoost products will not work for you Also keep in mind if your best signal is 1 bar at the Signal Antenna your coverage will be limited to a small room You could improve that with an upgraded antenna See page v 10 zBoost TRIO Workspace ZB570 Manual Warranty Information Limited 1 Year Manufacturer Warranty Warranty Registration at www zBoo2. zBoost extending cell zones zBoost TRIO Workspace ZB570 Manual Models e ZB570A e ZB570V zBoost products have a 30 day money back guarantee when purchased directly from zBoost If product is purchased from a reseller or third party the purchaser is subject to the policies of the third party 1 year manufacturer warranty Warranty registration at www zBoost com v 0114 zBoost TRIO Workspace ZB570 Manual FCC Requirements This is a CONSUMER Device BEFORE USE you MUST REGISTER THIS DEVICE with your wireless provider and have your provider s consent Most wireless providers consent to the use of signal boosters AT amp T Sprint T Mobile Verizon and 90 additional carriers have already given consent for all consumers to use this device Some providers may not consent to the use of this device on their network If you are unsure contact your provider You MUST operate this device with approved antennas and cables as specified by the manufacturer Antennas MUST be installed at least 20 cm 8 inches from any person You MUST cease operating this device immediately if requested by the FCC or a licensed wireless service provider WARNING E911 location information may not be provided or may be inaccurate for calls served by using this device FCC contact information www fcc gov signal boosters registration Any product modifications that use unauthorized antennas cables and or coupling devices
3. the rating would have to be reduced by 3 5 dB especially where the output is re radiated and can cause interference to adjacent band users This power reduction is to be by means of input power or gain reduction and not by an attenuator at the output of the device Cet appareillage num rique de la classe B r pond a toutes les exigences de interf rence canadienne causant des r glements d quipement L op ration est sujette aux deux conditions suivantes 1 ce dispositif peut ne pas causer l interf rence nocive et 2 ce dispositif doit accepter n importe quelle interference re ue y compris l interf rence qui peut causer l op ration peu d sir e Le fabricant nominale de la puissance de sortie de ce mat riel est simple transporteur Pour les situations lorsque plusieurs signauxporteurs sont pr sents l valuation devrait tre r duite de 3 5 dB en particulier lorsque le signal de sortie est r mise et peut provoquer des interf rences adjacentes a la bande utilisateurs Ce pouvoir est de la r duction par le biais de la sortie d alimentation ou la r duction de gain et non par un att nuateur a la sortie du dispositif Please note This unit has been approved for use in Canada under RSS 131 however consent for the use of this device to improve cellular or PCS coverage must be obtained through your cellular or PCS provider prior to placing the unit in operation Please refer to the Industry Canada document CPC 2 1 05
4. AWS PCS 10 12 dBi CANT 0043 Window Mount External Antenna Wideband Directional Panel LTE CEL AWS PCS 6 7 dBi Coax Cable To be used in addition to the cable included in your kit Accessories YX012 Outdoor External Antenna Grounding Kit The FCC requires that this panel antenna has a minimum horizontal separation of 6 feet 2 meters from other CMRS commercial mobile radio service devices zBoost TRIO Workspace ZB570 Manual Table of Contents FCC Requirements ete erect el ee es te acheter lms cerns em nee an kk kk KK K k KK K KK KK k KK KK KA Kl KA i FCG INOM le DD DD E E e E i Industry Canada acer 0 ic 0 gc ee eee ere ence ee emer ee et mete este kk kk kk kk K k ere tee rere ii amp ooWleln l si lle Sy NN ee a E O en er ee rrr Ea ii jir lole Sct cere ec create eda ge dee ha aside gam ee crt eta eo op eee MJMZ M ii MN NV SS yy rr rbrerbrr rrr E r iii Dance l elb oe _w w7 w_ r ewl mmmmmnmmmm W W W WXWasXIok iii Safety and Product Warranty Information E L kk kkk kk kk kaka kk kk kk AK KA KK KK KK kk KAR K KK KK KA AA A iii Pa4Ckage Contents s cinika xl xca x n kare nak aa ke k ya naa k aa xa kn xa ka a n kak n a kar kak kay K aa xud M W k a a Wla da b da a s k RA Ka l Ze K K iv Optional PGC ON Sacre asec ce sce ate este ns dace AA AA A WAA AA ARA AWA AA WAA RAA KA KAR AA WAA AA HAK annnm AWA WAW WA WR vV Tabl e
5. Initial Power Up Light Mode Status Cycle RED System is powering up Please allow up to 30 seconds Flashing BASE UNIT will GREEN flash GREEN once for every 2 dB less than optimal system gain Three flashes or less indicates the system will still operate properly After Initial Power Up Unplug the BASE UNIT power supply Relocate the SIGNAL ANTENNA to pick up the strongest signal from your wireless carrier Move the SIGNAL ANTENNA as far away from the INDOOR ANTENNA as possible with at least 15 ft of horizontal separation Plug the BASE UNIT power supply back in Wait 30 secs for the BASE UNIT to power cycle on SOLID zBoost is ready N A GREEN Flashing zBoost is in use N A GREEN 1 SOLID SIGNAL ORANGE ANTENNA and INDOOR ANTENNA are too close together SOLID RED Signal from the carrier s cell tower is too strong for the BASE UNIT to operate properly Flashing Excessive RED electronic noise in the system the BASE UNIT will not operate Unplug the BASE UNIT power supply 2 Move the SIGNAL ANTENNA as far away from the INDOOR ANTENNA as possible with at least 15 ft of horizontal separation Plug the BASE UNIT power supply back in Wait 30 secs for the BASE UNIT to power cycle on Unplug the BASE UNIT power supply Relocate the SIGNAL ANTENNA to another spot If you have a directional antenna re aim it to reduce carrier signal strength Plug the BASE UNIT
6. keep the original box and packing material in case you need to return your product Before requesting repair service Make sure you have at least 15 feet of horizontal separation between Signal Antenna and Base Unit and that the Signal Antenna is at least 3 feet above metal If red light is on system is receiving signals from either the mobile device or the base station transceiver which are too strong for proper operation Please unplug your system Re orient your Signal Antenna and or Base Unit to reduce the excessive signal source Plug your system back in If still solid red call customer support 1 800 871 1612 To get warranty service Warranty service will be provided by zBoost If you believe you need service for your unit contact zBoost at 1 800 871 1612 or support zBoost com A representative will go through a diagnostic checklist with you If it is determined that the product needs to be returned for service or exchanged you will receive a return merchandise authorization RMA number The representative will give you complete shipping details Do not return products to zBoost without a Return Authorization Number RMA To get out of warranty service To obtain out of warranty service contact zBoost at 1 800 871 1612 or support zBoost com for information on the possibility of any costs for repair or replacement of out of warranty products Reminder Record the model and serial number found on the product below Mode
7. limited remedy Because some jurisdictions do not allow limitations on how long an implied warranty last or the exclusion or limitation of liability for consequential or incidental damages the above limitations may not apply to you For full warranty guidelines see page 11 zBoost TRIO Workspace ZB570 Manual Package Contents Before you begin make sure all of the following parts came with your zBoost TRIO Workspace Literature Contents SETUP OVERVIEW Setup overview Product Contents zBoost Base Unit Indoor Antenna Power Supply RG 6 Coax Cable 50 ft Signal Antenna 2 Signal Antenna Short and Long Suction Cup Attachments zBoost TRIO Workspace ZB570 Manual Optional Accessories The following accessories are authorized for this zZBoost product Please see our website for a complete selection To order call 1 800 871 1612 or visit www zBoost com Broadcast Antennas Indoor CANT 0039 Indoor Broadcast Antenna Omni Whip Direct to Booster Black Wideband LTE CEL AWS PCS 1 dBi CANT 0045 Indoor Broadcast Antenna Wideband Directional Panel LTE CEL AWS PCS 8 7 5 dBi YX052 Indoor Broadcast Antenna Wideband Omnidirectional Ceiling Mount LTE CEL AWS PCS 1 2 dBi External Antennas Outdoor CANT 0040 Outdoor External Antenna Wideband Omni Directional LTE CEL AWS PCS 3 5 dBi CANT 0042 Outdoor External Antenna Wideband Directional Log Periodic LTE CEL
8. of Kuna CP Nr ea waz 1 V GT Vl i sa saya xanay en xa ran uc xua yak du rl ana b aka d r r d d w VE ee ee y W KA ra r AA Yu W 2 Why Indoor Signals Can Be VV eaK cu kk kek k k kk kak k kk kk K k k k kK kK K k KK KK KK KK 2 Preparing to Set Up Your zBoost Product K K llll kak kaka kkkkk kak KARA ARA AA AA A AKA AA KAR AA AA A KAW AWA A A WA WA A A WR n 3 Check for Signal Strength L eee ee tener error en renee ere kk kk kk kak Te eer K k K K k kK Ka K k k kK KK A KK KAK KK 3 Setting Up Your zBoost Signal Booster cccccccsessssseeeeeeeeceesssseeeeeeeeeeeesssneeeeeseeeaeesseeeeeessooessnseeesssees 4 FIRST Place the Signal Antenna on the interior of a window located in the area of best signal 4 SECOND Place the zBoost Base Unit where you want to create a Cell Zone M 5 THIRD Run the provided coaxial cable between the Base Unit and Signal Antenna 5 FOURTH Connect zBoost Base Unit to the provided power supply and plug into a power outtlet 6 Improving Your Coverage Area rciiiccaveacdinctntinsansiennicnenvnrentezadsecnad KAK AKA KA KAK A AA AA AA HK KK KK AA AA AA A A KAK A A A KA KA KIR KK KK KAW A KH KIR KK K 6 zBoost Base Unit Light Indicators K F kk kk kk kak kk kak kk KAK k KA kK A KAK KAK KK A KK A A KK KAR KK KK A A A A KK A KA KIR K KA 8 Technical Spec
9. power supply back in Wait 30 secs for the BASE UNIT to power cycle on Refer to Solution 2 zZBoost TRIO Workspace ZB570 Manual Technical Specifications Product Specifications for zBoost TRIO Workspace ZB570V a Frequenc Uplink 776 787 MHz Uplink 1850 1910 MHz Uplink 824 849 MHz q y Downlink 746 757 MHz Downlink 1930 1990 MHz Downlink 869 894 MHz Band supported A D B E F C A B A B System gain 58 dB 64 dB 58 dB General Specifications 3W standby 7W max signal 2 5A Max Coverage open areas Desk area Up to 1 500 sq ft Product Specifications for zBoost TRIO Workspace ZB570A Ereatene Uplink 704 716 MHz Uplink 1850 1910 MHz Uplink 824 849 MHz q y Downlink 734 746 MHz Downlink 1930 1990 MHz Downlink 869 894 MHz Band supported A D B E F C A B A B System gain 58 dB 64 dB 58 dB Naiwarks CDMA GSM GPRS EDGE EVDO 1xRTT UMTS General Specifications Power Consumption 3W standby 7W max signal 2 5A Max Wall Supply Input Voltage 100 240VAC 50 60 Hz 5 0VDC System Certifications FCC Parts 15 amp 20 Industry Canada Input and Output Impedance TNC Connector 50 Ohm F Connector 75 Ohm Base Unit Size and Weight 5 x 7 x 1 25 9 oz Operating Conditions Indoor Use Only 40 105 F Coverage open areas Desk area Up to 1 500 sq ft The Manufacturer s rated output power of this equipment is for single carrier op
10. Section 6 1 available or viewable at http www ic gc ca epic site smt gst nsf en sf08942e html Copyright Notice This manual is copyrighted All rights reserved This manual whole or in part may not be copied photocopied reproduced translated or reduced to any electronic medium or machine readable form for distribution This manual whole or in part may not be modified without prior consent in writing from zBoost Copyright 2014 by zBoost Trademarks Wireless Extenders Wi Ex the Wi Ex logo zBoost the zBoost logo and Extending Cell Zones are registered trademarks of zBoost zBoost TRIO Workspace ZB570 Manual Safety and Product Warranty Information Safety Guidelines In accordance with FCC requirements of human exposure to radiofrequency fields the radiating element antenna shall be positioned such that a minimum separation distance of 8 inches 20cm is maintained between the radiating element and the user and or general population Limited Liability In no event shall zBoost be liable for any direct indirect special punitive incidental exemplary or consequential damages or any damages whether in an action under contract negligence or any other theory arising out of or in connection with the set up of use of inability to use or performance of the information services products and materials available from this manual These limitations shall apply notwithstanding any failure of essential purpose of any
11. al meters update every 6 to 10 seconds An increase of only one bar typically indicates a 4x to 10x signal increase zBoost TRIO Workspace ZB570 Manual Setting Up Your zBoost Signal Booster MASTER BEDROOM KITCHEN BEDROOM The Metro Workspace boosts signal up to 1 500 square feet making it perfect for apartments condos and lofts No outside antenna placement is required Boost voice and data transmission and improve call clarity in 4 easy steps FIRST Place the Signal Antenna on the interior of a window located in the area of best signal Determine the location that provides the strongest signal using the signal strength indicator on your cell phone Find the location on the window that provides the most bars of signal strength Before proceeding make sure that the intended surface is clean and clear of any dust Then choose the suction cup attachments appropriate for your setting short or long fasten to the Signal Antenna and secure to your window Note Energy efficient windows will likely block signal from reaching the Signal Antenna In this case it is necessary to move the Signal Antenna away from this window to another location You may also upgrade to an outdoor rated antenna part cant 0042 if mounting an antenna outside is possible In order to capture the strongest signal you may do one or all of the following zBoost TRIO Workspace ZB570 Manual 1 Move the antenna around the wind
12. ation NOTE The Base Unit can be plugged into a standard 2 or 3 prong 110 VAC receptacle using the Included power supply The power supply consumes less than 10W less than 0 2A AC For more information on power consumption see Technical Specifications on page 9 Confirm That Your zBoost is Working Properly Improving Your Coverage Area When your zBoost system is in place and fully connected you should walk throughout the room and see that you are able to reliably place calls Remember coverage varies based on outdoor signal level home construction and antenna placement Coverage in adjoining rooms will be reduced due to walls or ceiling floors Should you desire to improve coverage you may e Move the Base Unit and or adjust the angle of the Indoor Antenna e Move the antenna around the window higher is usually better e Move the Base Unit farther from the Signal Antenna or around a wall zBoost TRIO Workspace ZB570 Manual Indoor Antenna E eet Power Supply Coax Cable Cell phone signal bars are approximate and vary from phone to phone The number of bars can fluctuate widely depending on the location of the phone the position or angle of the phone weather etc Most cell phone signal meters update every 6 to 10 seconds An increase of only one bar typically indicates a 4x to 10x signal increase zBoost TRIO Workspace ZB570 Manual zBoost Base Unit Light Indicators During
13. eless routers or wireless access points The zBoost TRIO Workspace performs best when there are no 15 ft obstructions between the zBoost Base Unit and separation your mobile device Indoor Antenna THIRD Run the provided coaxial cable between the Base Unit and Signal Antenna Should you need additional cable length 15 foot extensions Part YX030 15w are available at www zBoost com Power Supply Use the provided RG 6 coaxial cable to connect the Signal Antenna and the Base Unit Coaxial connections can loosen when the cable is moved Be sure the connections stay hand tight zZBoost TRIO Workspace ZB570 Manual The total cable length should not exceed 65 feet A longer cable is helpful only if it allows you to place the Signal Antenna in a location where you measure stronger signal FOURTH Connect the zBoost Base Unit to the provided power supply and plug into a power outlet Upon initial power up the LED will cycle RED GREEN and ORANGE for 30 seconds After 30 seconds a series of GREEN flashes will indicate the quality of your setup Following this a solid GREEN light indicates normal conditions If it is not solid GREEN follow the instructions in the Base Unit LED Indicators section Adjustments may be needed to optimize performance If you find the increased signal coverage is acceptable however no additional adjustments are needed See ZBoost Base Unit Light Indicators on page 8 for more inform
14. eration For situations when multiple carrier signals are present the rating would have to be reduced by 3 5 dB especially where the output signal is re radiated and can cause interference to adjacent band users This power reduction is to be by means of input power or gain reduction and not by an attenuator at the output of the device This product is covered by patent US 7 706 744 Other U S and foreign patents pending 9 zBoost TRIO Workspace ZB570 Manual Frequently Asked Questions What can I expect my cell phone signal range and strength to be inside my home The closer you are to the base the stronger the signal This will vary with different conditions Some of the conditions that will affect the improved data coverage area are signal strength outdoors the type of building materials in the home the placement of the unit and the antenna s proximity to cellular towers You can expect that your indoor coverage will be improved You will experience faster more reliable data where you didn t before The degree of improvement will depend upon many factors The intent of zBoost products are to bring outside coverage inside Just as the signal bars move up and down when outside the boosted signal will fluctuate in a similar fashion Is a cellular phone signal booster the same as a wireless router will it help my WiFi signal The zBoost unit will not help your WiFi service The WiFi in your home operates on a different frequency
15. ifications cine scan secrete sec cess ree AA KAKA AA KA KAWA AA KA AA AA KA A AA KAKA AA KAK A AA A A KAK KAW KA WA WA wa 9 Frequently Asked QueStiOnS cc ccceeseeeeeee eee kk kkkkk aka kkk kk KAK AA AKA KAK AA A AA A A KK KK A A KA A A A A KK KA A KAR A KK KK KK A A AK A HIK HK KK A A A A AIR HIK KA 10 Warranty Information sssaaa axa xua K na kn ka E a a Ku a aa U K Xa dik a K a a W n kr Wa k K n Aka a aw xen k 11 zBoost TRIO Workspace ZB570 Manual Overview Thank you for choosing zBoost You will now be able to use your cell phone INSIDE your home Gone are the days when you had to go to the window upstairs or walk outside to use your cell phone Like a skylight that brings sunlight into your home zBoost TRIO transports and amplifies the outdoor 2G 3G and 4G data signal into your home Why Indoor Signals Can Be Weak There are several obstacles that can contribute to the poor reception you receive in your home 1 Location of the Cell Phone Tower in Relation to Your Home While cell phone providers have tried to place cell phone towers to provide the best overall coverage local ordinances and terrain features can impose restrictions on where these towers can be placed thus limiting the signal strength available at your location 2 Obstructions Caused by Buildings Terrain and Trees Cell phone signals can be completely blocked or reflected by buildings walls trees hills and other terrain featu
16. is no longer FCC compliant and will void the product warranty FCC Information FCC ID S04ZB570 TRI VLTE S04ZB570 TRI ALTE Warning Changes or modifications to this device not expressly approved by zBoost could void the user s authority to operate the equipment Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If the equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment to an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This transmitter mu
17. l Serial Purchase Date 12 zBoost TRIO Workspace ZB570 Manual
18. ow higher is usually better 2 Use the long suction cup attachments provided in order to create a greater angle in which to capture the signal The suctions cups must be vertical on the window as pictured with cable at the bottom not on the side Avoid draping the coax near the antenna ce Antena A 3 Keep the Signal Antenna 2 feet from any metal SECOND Place the zBoost Base Unit where you want to create a Cell Zone Connect the Indoor Antenna and coax to the Base Unit and place it where you need A signal For the widest possible signal area it JA is recommended that you position the Base Unit near the middle of a room or mount it 27 on an interior wall This Base Unit uses an omni directional antenna that delivers signal power una in a circular pattern around the antenna The i zBoost TRIO Workspace does not require zBoost Base Unit Assembly Avoid placing the Signal Antenna near metal such as wiring things likely in near a window e g window edge frame A C unit metal siding etc vertical separation however the Signal Antenna and Indoor Antenna should have at least 15 feet of horizontal separation Increasing separation of the 2 antennas will optimize ZBoost performance Suction Cup Attachments _ IP Signal Antenna Coaxial Cable For best results keep the Base Unit off the floor and at least 2 feet away from other cords metal objects or other wireless devices such as wir
19. p of the unit Product replacement because of misuse accident lightning damage unauthorized repair or other cause not within the control of zBoost e Incidental or consequential damages resulting from the product Some states do not allow the exclusion of incidental or consequential damages so the above exclusion may not apply to you e Any modifications or other changes to the product including but not limited to software or hardware modifications in any way other than as expressly authorized by zBoost will void this limited warranty e Product that has been modified or adapted to enable it to operate in any country other than the country for which it was designed manufactured approved and or authorized or repair of products damaged by these modifications All zBoost products that are packaged with other zBoost accessory products are intended for resale and use as a single unit and such product kits are required to be sold to the end user or subsequent reseller as packaged The de kitting and sale as a standalone product of any one or more components of such a product kit is in violation of zBoost warranty No de kitted product will be eligible for return for any reason The sale of separate not kitted cable antennas and other accessories is allowed and fully warranted n ZBoost TRIO Workspace ZB570 Manual Make sure you keep Please keep your sales receipt or other document showing proof of purchase Also
20. res resulting in low signal strength 3 Energy Efficient Windows Energy efficient windows contain a metal film that can affect signal penetration into the house lt A gt xN A Y l Y l Y wail Yaon aay zBoost TRIO Workspace ZB570 Manual Preparing to Set Up Your zBoost Product Check for Signal Strength Before placing the unit in your home make sure that you have reliable signal and fast reliable data speeds outside your home in the attic at roof level or wherever you plan to place the Signal Antenna zBoost can only bring signal into your home when it reaches the Signal Antenna If there is no signal zBoost will not work for you If a weak signal is available at ground level check the signal strength in your attic or at roof level location where the signal will likely be stronger and where the Signal Antenna can be placed for best performance If you have reliable fast data speeds outside your home then zBoost can bring the signal into your home If only one signal bar is displayed on your cell phone outside indoor coverage will be limited to one small room We recommend placing the Signal Antenna outside and or purchasing a zBoost upgrade Signal Antenna for increased coverage see page v Cell phone signal bars are approximate and vary from phone to phone The number of bars can fluctuate widely depending on the location of the phone the position or angle of the phone weather etc Most cell phone sign
21. st com zBoost warrants every zBoost product to be free from defects in material and workmanship under normal use for the warranty period of one year Who Is Covered You must have proof of purchase to receive warranty service A sales receipt or other documentation showing the product purchased and the purchase date is considered proof of purchase This limited warranty extends only to the original consumer purchaser or any person receiving the product as a gift from the original consumer purchaser and to no other purchaser or transferee What is Covered Warranty coverage begins the day you purchase the product For one year from the original date the zBoost Cell Phone Signal Booster will be repaired or replaced with a new repaired refurbished or comparable product whichever is deemed necessary by zBoost if it becomes defective or inoperative The exchange will be made without charge to you for parts and labor You will be responsible for the cost of shipping to the location designated by zBoost If zZBoost cannot reasonably repair or replace the unit then zBoost may at its sole discretion refund the price you paid for the product or the price of the unit All products including replacement products are covered only for the original warranty period When the warranty on the original product expires the warranty on the replacement product also expires What is Excluded Your warranty does NOT cover Labor charges for set u
22. st not be co located or operating in conjunction with any other antenna or transmitter In accordance with FCC requirements of human exposure to radiofrequency fields the radiating element antenna shall be installed such that a minimum separation distance of 20cm 8in is maintained from all persons Additionally the device must not be used above 10 m above ground zZBoost TRIO Workspace ZB570 Manual About zBoost zBoost the leader in cell phone signal boosters manufactures an award winning line of cell phone signal boosters that enhance the performance of your cell phone smartphone and wireless data card Uses patented technologies and protects the carrier networks 1 year manufacturer warranty register your product at www zBoost com Industry Canada Regulations IC ID 5544A ZB570TRIVLT 5544A ZB570TRIALT This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation The term IC before the radio certification number only signifies that Industry Canada technical specifications were met RF Exposure The manufacturer s rated output power of this equipment is for single carrier operation For situations when multiple carrier signals are present
Download Pdf Manuals
Related Search